Search Documents

By S. A. Moffatt, S. K. Kawatra, T. C. Eisele

This paper describes the decomposition of bulk samples to fine particles using alkali metal vapors. Basalt, pyrite, alumina, pyrex and quartz glass samples were exposed to sodium vapors at elevated temperatures for different time periods up to 30 hours. Examination of the particles showed that fragmentation occurred preferentially along grain boundaries. Emphasis of this paper is on the theory of the degradation mechanism and the size distribution of the particles produced.

Jan 1, 1992

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By Henk L. C. Meuzelaar

Most of us are aware of the relationship between the golden-yellow resin spots on Upper Cretaceous Wasatch Plateau coals and fossil tree resins (?amber?). Nevertheless, confusion remains about the exact chemical composition and structure of commercial coal resin preparations as well as their observed heterogeneity. In order to arrive at a more detailed chemical description we need to distinguish between micropetrographic, organic geochemical and process technological definitions of coal resins, which may include substantial quantities of constituents unrelated to fossil tree resins. New information on composition and origin obtained by Curie-point pyrolysis/evaporation in combination with isobutane chemical ionization mass spectrometry, as presented in this paper, points to the presence of four more or less distinct resin components: (1) a sesquiterpenoid polymer; (2) sesqui-and triterpenoid monomers and dimers; (3) a suite of triterpenoid alcohols, ketones and acids; and (4) a series of increasingly aromatized hydrocarbons with naphthalene and picene type skeletons. Moreover, a strong similarity is found between the composition of recent Dammar resin and fossil Wasatch Plateau coal resins. Some of the technological implications of these findings and the consequent need for a more precise chemical definition and nomenclature are discussed.

Jan 1, 1990

By F Melcher, M Wiedicke, A Wittenberg

Ferromanganese nodules form a specific category of widespread marine mineral deposits. The tremendous increase in metal prices during the last decade raised new economic interest in their exploration. The German Federal Institute for Geosciences and Natural Resources (BGR), which had been engaged in nodule research in the 1970s and 1980s, renewed its activities on this subject based on an exploration contract with the International Seabed Authority, signed in 2006. BGRÆs licence area û comprising 75 000 km2 û is located between the Clarion and the Clipperton Fracture Zones. In this so-called nodule belt north of the equator the sea floor reaches water depths of >4000 m. About 900 million tonnes of manganese nodules are expected there. In this study the fine-scale distribution of important elements in manganese nodules and crusts from a variety of locations was investigated. Besides 11 samples from the RV SONNE cruise SO-25, numerous samples from additional locations were included in this study for comparison. In general, the sample suite includes two genetic types of precipitates, manganese nodules and Co-rich crusts. A detailed characterisation of the distribution of major, minor and important trace elements in manganese nodules based on in situ microenergy dispersive X-ray fluorescence (¦-EDXRF) analysis is presented here. The data are compared with bulk major, minor and trace element data as well as with quantitative electron probe microanalysis (EMPA) data sets. The element distribution maps and profiles produced by ¦-EDXRF analysis with short or extended (in case of profiles) counting times, allow precise selection of æregions of interestÆ for further detailed investigation using high spatial resolution techniques (eg scanning electron microscope (SEM)-EDAX; laser ablation-inductively coupled plasma mass spectroscopy (LA-ICPMS); isotopic studies).

Jan 1, 2008

By Jinhua Wang

Based on engineering examples and theoretical analysis, the mechanism of chemical consolidation for fractured roadway surrounding rock was discussed. The chemical consolidating materials and three consolidating methods, that is, capsule, forced infusion and spraying, were introduced. Finally the application effects of the chemical consolidating technique to reinforce the fractured surrounding rock of roadways were analysed.

Jan 1, 1996

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By R. L. Curfman

From January 1, 1965 through July 5, 1970, the very difficult potash ore body of Texasgulf Inc. near Moab, Utah was mined by conventional methods. The mine was gassy, the temperature was high and structural conditions precluded a satisfactory or economical extraction ratio due to the undulating configuration of the ore horizon. In 1966, 67, and 68, alternative mining methods were considered, among which was solution mining of the ore body. Cost studies indicated that the use of crystallizers to evaporate the large amounts of water attendant to solution mining offered no chance of economic success. In 1969 additional testwork and cost studies were carried out utilizing solar evaporation. These studies showed economic potential and justified additional investigation. As a result of these studies, Texasgulf now gathers potash solids from these solar evaporation ponds, (Fig. l), after pumping them from the underground mine as brine. The investigations were concentrated in four basic areas : (1) area evaporation rates and crystal growth habits; (2) underground solution tests including heat transfer rates; (3) accelerated evaporation tests to provide material for metallurgical testing, and (4) tests of evaporation pond lining materials and application techniques, along with area surveys to ascertain if sufficient earth was available in the near vicinity to con-

Jan 1, 1974

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By AIME AIME

A MODERN copper reduction works has both a genera1 chemical laboratory for control work and a research laboratory for the study of improvement of present processes and better working-up of by-products. The division of work in the general laboratory would naturally differ in different plants. The following statement to the writer from a chemist in one of the works will give a good idea of the type. of work in the general laboratory :

Jan 1, 1929

By Joseph U. Messenger

A method of applying ammonium hydroxide to a drill stem containing hydrogen sulphide gas and hydro-gen-sulphide-bearing oil and water so as to remove the hydrogen sulphide as ammonium sulphide is de-scribed. It was concluded that the method allowed trips with drill pipe filled with sour fluids to be made more safely, more rapidly, and more economically. INTRODUCTION THE DANGER of poisoning rig crews during drill stem tests of sour wells by exposing them to hydrogen sulphide gas is well known in Canada. Concentrations of hydro-gen sulphide in sour gases range from 0 to 40 volume percent. There have been numerous casualties from hydrogen sulphide exposure during drill stem testing. Some have resulted in permanent injuries; in some cases the injuries have been fatal. For example, in Alberta in 1957 there were four deaths and 100 exposures which required medical treatment. These fatalities and injuries indicate the need for a more effective way of handling hydrogen sulphide in oilfield operations.

Jan 1, 1958

By A. Redman

Aquatic organisms are sensitive to free cyanide (HCN) though the presence of certain metals that can form stable complexes and thereby reducing both the amount of bioavailable cyanide. Recent work has suggested that consideration of HCN rather than total cyanide can provide the basis for water quality criteria. Cyanide is often present in complex effluents that affect speciation and bioavailability. We have developed a model to predict the speciation of cyanide in complex effluents and have shown that this model can predict the toxicity of metal-cyanide complexes in terms of HCN. This study evaluated available cyanide toxicity exposures with this model to assess the role of water chemistry (e.g., metal-cyanide interactions) on the observed. Toxicity endpoints based on total cyanide ranged over several orders of magnitude for a variety of metal-cyanide mixtures. However, predicted HCN concentrations among these same tests described the observed toxicity data to within a factor of 2. Aquatic toxicity can be well described using HCN though in certain metal-cyanide mixtures toxicity was jointly described by HCN and elevated levels of bioavailable metals. This work was performed in support of an industry-sponsored reassessment (Gensemer et al 2006) of the U.S. EPA water quality criteria for cyanide (EPA 1985) using free cyanide as the basis for the re-calculation. The work presented in this manuscript presents technical support for using free cyanide as the preferred basis for this recalculation.

Jan 1, 2011

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By Hun-Joon Sohn

Chemical metathesis and electrochemical reductive conversion of chalcopyrite in the presence of cupric ions were studied in sulfuric acid solutions for temperatures up to 90°C. The process results in the displacement of iron in the chalcopyrite lattice by copper ions with rejection of ferrous ions to the aqueous phase. The rate of reaction was found to be very slow, requiring subsieve-sized particles for extensive reaction to occur. The reaction was insensitive to copper ion concentration. Stirred ball milling of chalcopyrite introduces lattice strain. The reaction rate with strained particles was markedly higher than with annealed chalcopyrite. The reaction rate was found to be diffusion-limited, showing two distinct reaction stages corresponding to the formation of CuS (covellite) followed by Cu1.8S (digenite). The experimental activation energy for the first stage was 102 J (24.4 kcal) and the second stage 123 3 (29.4 -kcal) per mole. The rate-controlling process is diffusion of lattice ions, probably iron. The enhanced rate after milling is attributed to a recrystallization process which provides new paths for diffusion along dislocations and grain boundaries.

Jan 1, 1984

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By R. Agius, A. Nacu

"Cyanide destruction technologies are implemented at gold and silver operations to comply with the International Cyanide Management Code and meet ever more stringent discharge limits. Currently, the most common chemical cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide, and Caro’s acid. The cyanide destruction process used at an operation must reliably generate streams of acceptable quality at all times, and depends on numerous factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Selecting the most appropriate cyanide destruction process and determining the process design criteria requires accurate laboratory testing. This paper presents and discusses the results of a number of cyanide destruction evaluations that have been conducted to reduce cyanide concentration in process solutions or cyanidation tails. Laboratory testing provides important insights into reagent consumption and other factors required to achieve the target residual weak acid dissociable cyanide (CNWAD) levels.INTRODUCTION Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values comprises both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable, even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution. Total cyanide levels in solutions are always equal to or higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically in Canada, CNTOTAL levels cannot exceed 1 mg/L in solutions discharged to the environment."

Jan 1, 2017

By P Wollants, B Blanpain, R Ding

Vacuum oxygen decarburisation (VOD) is the refining process used by ALZ (Genk, Belgium) for their production of stainless steels. The process consists of three stages: oxygen blowing at a pressure of 100 mbar, degassing, and reduction of the slag with ferrosilicon at 5 mbar. The magnesia-chromite bricks used in the slag zone of the ladles suffer from acute wear. In this paper results obtained from a program to improve the refractory life span are presented. The dominant wear phenomena were identified with an electron microscopy study of bricks taken from different locations in the ladle. Concurrently a dynamic model for the vacuum oxygen decarburisation (VOD) refining process was developed. The model calculates the elementsÆ oxidation rate during the blowing oxygen stage and allows the continuous calculation of the change of the metal, slag and gas composition throughout the VOD process. From these activities a general scheme of the refractory wear was worked out and measures to improve the refractory life were proposed and implemented.

Jan 1, 2000

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By Kevin L. Purdy

Chemical dewatering aids for mineral slurries generally fall into two classes: surfactants and flocculants, which can be used separately or together. Current industrial use of both types of reagents is summarized for sulfide and non-metallic minerals, as well as uranium and gold leach residues and coal refuse. Laboratory testing for reagent selection is briefly discussed along with reagent preparation. Chemical properties of the reagents which affect the suitability for particular applications are analyzed. [BLANK PAGES - Are in the original]

Jan 1, 1986