Search Documents

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

By Gennaro G. Marino

During the preliminary design stages of the Illinois Division of Natural Resources(DNR) building, it was discovered that an old coal mine was present some 70 m (220 ft) beneath the building site. The new DNR building to be constructed is 36 m (120 ft)wide and 134 m (440 ft) long. It has three stories above grade and abasement level. The building is oriented north-south and has east and west ponds next to it (Fig. 1). The building is located on the State Fairgrounds in Springfield, IL. Given the history of surface subsidence of these underground coal mines in the Springfield area, there was concern about the potential for future subsidence at the building site. Mine subsidence events in the area have resulted in more than 0.9 m (3 ft) of settlement and have caused significant structural damage.

Jan 1, 2000

By A. V. Roschin, N. V. Malkov, V. N. Karnoukhov, V. E. Roschin

Reduction interactions in solid phases are widespread and occur in most complex metallurgical processes. Among these processes, reactions between oxides and carbon have a special importance. The authors conducted experiments for comparison of reduction by different reducing agents of impregnated chromite ores, in which grains of the reducible chromite spinel are isolated from direct contact with the reducing agent by layers of non-ore material. The results of the experiments have revealed that the beginning of reduction is preceded by thermal and impurity order-disorder transformation of the oxide lattice whilst the transformation of the oxide lattice into the metal lattice takes place as a result of removal of oxygen anions from the zone of metal germ nucleation. Since anions are charge carriers, increase of their mobility can be monitored by changes in electrical conductivity of oxides. Respective measurements of electrical resistance of ores of different metals and a number of pure refractory oxides under heating have indicated that the beginning of reduction coincides with the time of drastic (tens of thousands times) increase of conductivity of the oxides. Besides, the temperature of the beginning of carbon-thermal reduction is in line with the Tammann temperature, i.e. the temperature of transition from the predominantly surface diffusion to volume diffusion. Segregation of metals from the oxide lattice occurs as a result of merging of anion vacancies with defect electrons on defects of the oxide lattice. The transformation of the oxide lattice into the metal lattice requires a certain concentration of anion vacancies and inflow of electrons from the reducing agent to the site of metal segregation. Such inflow has no difficulties due to the mixed anion-electron nature of high-temperature conductivity of oxides. Thus, the reduction is not determined by oxygen diffusion, it is determined by oxygen vacancies diffusion whose speed exceeds the speed of oxygen diffusion by orders of magnitude. This determines that the kinetics of reduction considerably exceeds the kinetics of oxidation at similar temperatures since oxidation proceeds by means of mass transfer of oxygen through the layer of the generated oxide.

Jan 1, 2004

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Kent C. Condie

Precambrian terranes in the Rocky Mountain region decrease progressively in age from the Archean Wyoming Province (> 2.5 b.y.) to the late Proterozoic in West Texas (figs. 1,2). Within the Wyoming Province, most dates fall near 2.7 b.y. although some are recorded at 2 3.8, 2.9, and 2.6 b.y. Although Penokean (- 1.8 b.y.) deformation and plutonism are recorded in southeastern Wyoming, most Precambrian rocks south of the Wyoming shear zone, which separates the Archean and Proterozoic provinces, are < 1.76 b. years in age. Supracrustal rocks in Colorado, western Arizona, and northern New Mexico fall in the range of 1.72-1.76 b.y., those in central New Mexico about 1.65 b.y., those in southeastern Arizona and southwestern New Mexico about 1.70 b.y., and those in West Texas 1.1-1.2 b.y. The Wyoming Province is comprised chiefly of 2.7 or 2.9 b.y. tonalitic gneiss terranes intruded by 2.6 b.y. granites in the central and southern parts of the province. Supracrustal rocks are minor and include greenstone belts comprised chiefly of pillow- ed tholeiites and graywackes and remnants of quartzite-shale successions. Metamorphic grade in greenstone-gneiss terranes ranges from upper greenschist to amphibolite facies and in quartzite-gneiss terranes from upper amphibolite to granulite facies.

Jan 1, 2013

By Gordon Bath

During the summer of 1946, the Division of Geophysical Exploration of the U.S. Bureau of Mines established several primary magnetic base stations near important iron-producing districts in Minnesota, Michigan, and Wisconsin. Stations were located in groups of four to six in six separate base-station areas, and each position was marked with a concrete monument. Differences in magnetic intensity between stations in these areas, as well as the difference between each area and a magnetic datum at the magnetic observatory of the Coast and Geologic Survey at Cheltenham, Md., were measured with a modified Askania magnetometer. Measurements also were made with a Hotchkiss superdip to study the usefulness of the stations for the calibration of instruments of this type. The work was planned and supervised by F. W. Lee, chief of the Division of Geophysical Exploration, and Edward F. Fitzhugh, Jr., chief of the Minneapolis Division of the Bureau of Mines. Special mention is due Harold B. Ewoldt, Bureau of Mines engineer, for his assistance in the field work, especially in locating and establishing monuments. Special mention also is due Clyde L. Holmberg, of the Bureau of Mines, for the magnetic measurements made with the Hotchkiss superdip. Helpful suggestions were received in the field from H. L. James, of the U. S. Geological Survey. Acknowledgment is made of the cooperation of Stephen Royce, Irving E. Beckwith, Arthur Johnson, and Josiah Royce of Pickands, Mather & Co., and A. E. Matson, of Butler Bros. The U. S. Coast and Geodetic Survey furnished daily magnetograms from the Cheltenham Magnetic Observatory as well as calibration equipment and values of absolute magnetic intensity. Short-term forecasts of ionospheric conditions were obtained from the National Bureau of Standards.

Jan 1, 1951

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. [SECRETARY&apos;S NOTE.-All of these notices have been revised, and some of then have been more or less completely prepared, by me. To those which contain more particularly the expression of my personal feeling, my initials have been appended. The labor of preparing or editing these paragraphs has been in many respects both welcome and interesting, on the one hand, and sorrowful, on the other. In going through the list, I have repeatedly felt like one who, visiting the Morgue, suddenly comes upon the pale face of a dear friend, of whose death lie was not aware ; and, even when this fact was known to me, the work of recording it has brought upon me a flood of recollections, almost preventing the discharge of that official duty. The list for 1907 seems to me to he peculiarly sad, comprising, as it does, so many sudden deaths by violence or accident, so many veterans, removed too soon, and so many young men whose early departure impoverishes the future, even more than the present. Probably, this feeling on my part is largely due to the circumstance that the increased membership of the Institute necessarily in¬volves an increase of the annual death-list. Probably, also, it is connected with the circumstance that during the first years of the history of the Institute-say from 1871 to 1880-it was joined by men of all ages, and that the death-rate is consequently now above the average which would result from the normal annual addition, principally of young men. And finally, I must admit that, as one of the original members of the Institute, and practically connected with it for nearly thirty-seven years as Acting President, President or Secretary, I am peculiarly impressed and depressed by the successive deaths of those who were my associates in the years of its early struggles and triumphs. I do not wish to inflict upon my younger colleagues the melancholy reflections of an increasingly lonesome old man. In fact, my prevailing mood concerning the Institute is not at all melancholy, but triumphant and hopeful. If I may be permitted to preach at all, I would enforce, from the texts given below, a moral which many of them declare so forcibly as to preclude the necessity of expository enforcements-namely, the duty of every one of us, old or young, to give to his brethren, as he goes along, and without waiting for some future occasion for a comprehensive and monumental contribution to technical literature, the results of his observation and experience. When I look at this list of names, my personal sorrow over many of them is drowned in my professional reflection as to each and all-How much has died with

Jan 1, 1908

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By P. G. Gresse

The Orange-Vaal River system is known to be the primary secondary source for alluvial diamond deposits in the northern Cape and along the west coast of Namaqualand. The higher order sources for diamonds contained within this system are still not defined entirely to satisfaction, but certainly include kimberlite pipes exposed in the catchment regions of these rivers. The focus of alluvial diamond mining along the Orange-Vaal system recently changed from the traditional areas in the upper catchment regions?the Barkly West, Christiana, Bloemhof, Wolmaranstad, Schweizer-Reineke region, and the lower regions near the mouth of the Orange River at Baken, Alexander Bay and Oranjemund, to the area between Douglas and Prieska?the so-called mid-Orange region (Figure 1).

Jan 1, 2003

By HARRINCTON EMERSON

UNEMPLOYMENT is the most ominous shadow ahead of the industrial nations today. Only two great industrial countries are free from unemployment, France and the Soviet Commonwealth. In France the social unit is the family, not the individual. This has saved France. In the Soviet Commonwealth, development is proceeding so rapidly from agricultural to industrial that there is still a dearth of muscle workers in the non-agricultural enterprises. In the other industrial countries unemployment results both from acute temporary recession in industrial activities and from the rapidly increasing substitution of the machine for the man. Temporary recessions can be mitigated, alleviated by makeshifts, often ill considered. Secular recessions due to a fundamental change in the way of accomplishing physical, chemical results cannot be cured by any makeshift. There must be a period of transition. There is therefore before us the three- fold problem, immediate, prosimate and ultimate.

Jan 1, 1930

By J. Goyman, K. R. Rawling

"1.1 Location and Transportation ServicesNanisivik Mines Ltd. is located at latitude 73°, 3,200 km north of Montreal and 700 km north of the Arctic circle, on the south side of Strathcona Sound, which is an arm of Admiralty Inlet, in Northern Baffin Island. The orebody and mill site are 4 km distant from Strathcona Sound which provides deep water anchorage for ocean transportation of concentrate to Europe during the short northern shipping season from mid-July to mid-October.The operations and the resident community have direct jet aircraft service from Montreal two days per week, and local nights connect with other Arctic communities in the northern Baffin region. Bulk supplies and general cargo are delivered in the summer shipping season.1.2 HistoryThe Texas Gulf Sulphur Company, now Kidd Creek Mines Limited, staked claims in the Nanisivik area in 1957 and carried out exploration through to 1968. After the Kidd Creek orebody was found, Texas Gulf optioned the property in 1972 to Mineral Resources International Inc. (MRI), which undertook further exploration and completed a feasibility study.Nanisivik Mines Ltd. was formed in 1975, with MRI as the majority shareholder and minority shareholdings held by Metallgesellschaft, Billiton and Texas Gulf. Strathcona Mineral Services Limited was retained to manage the project during both the construction and operational phases."

Jan 1, 1984

By R Long

The founder of social psychology is sometimes identified as Kurt Lewin. In a 1947 article, Kurt Lewin coined the term ‘group dynamics’. He described this notion as the way that groups and individuals act and react to changing circumstances. Lewin theorised that when a group is established it becomes a unified system with unique dynamics that cannot be understood by evaluating members individually. The discipline of social psychology really emerged out of World War II and tackled questions associated with human judgement and decision-making by the Nazis. For a comprehensive look at the development of social psychology look at Abelson, Frey and Gregg (2004).Social psychology is concerned with the way social arrangements affect human judgement and decision-making. What the author has done is apply the knowledge of this new discipline to an understanding of risk, safety and leadership. This paper will explain some of the developments in social psychology, such as the discovery of the bystander effect, Groupthink, bounded rationality, heuristics, risk homeostasis and the Milgram effect.The social psychology of risk tackles the way decisions are made about risk in their social context. Unless organisations understand that decision-making is socially conditioned, they are unlikely to be able to tackle the complexities of culture change or the development of risk maturity.The paper will offer a new understanding of why people do what they do, how risk makes sense and why a ‘dumb down’ approach to safety is dangerous. A model will also be presented that shows the pathway to risk maturity.CITATION:Long, R, 2016. The social psychology of risk, safety and leadership maturity, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 31–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By Peter Fullagar, Adel Vatandoost, Steve Walters, Toni Kojovic

"Traditional comminution tests are a vital component in every mine plant design. Comminution behavior governs both the cost of equipment and its operating efficiency. Most comminution tests are conducted off site on a limited number of samples, owing to the high costs and long lead times involved. Therefore a strong incentive exists to find alternative means for efficiently characterizing comminution behavior for a truly representative suite of samples. The potential for inferring comminution behavior from drill core is investigated in this paper. Our approach involves development of small scale comminution tests on the one hand, and measurement of a wide range of core attributes on the other. Our focus is the relationship between petrophysical properties and comminution behavior.Petrophysical properties of archival diamond drill core from the Ernest Henry Mine (Queensland, Australia) have been measured using a Geotek multi-sensor petrophysical core logger. We have investigated the relationship between the petrophysical properties and the corresponding small scale A*b and estimated Bond mill work index test results for 2m composites of the core. Core samples were petrophysically classified by means of cluster analysis. Comminution behaviour was then modeled for each cluster via multiple regression. The results suggest that prediction of the comminution behavior on the basis of petrophysics is viable at Ernest Henry.INTRODUCTIONMineral processing is the most important downstream operation for mining engineers and metallurgists since most mined materials are subjected to some type of comminution or beneficiation operation (SME, 1992). Comminution or size reduction is typically the first stage of processing. Size reduction steps (crushing and grinding) in any plant consume large amounts of energy, normally more than 50% of total energy (Weiss, 1985). Therefore, it is desirable to obtain laboratory results to design the size reduction equipment appropriately. One of the main factors that control the selection of hard-rock crushing equipment and the design of a crushing circuit is the mechanical character of the ore(s). Work index, density, abrasivity, compressive strength and clay content are essential parameters for ore characterisation (SME, 1992)."

Jan 1, 2009

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN&apos;m). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003