Search Documents

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By R. Daignault et G. O. Allard

The Chibougamau area represents a part of the Abitibi greenstone belt. The rocks constitute a volcanic pile (Roy Group) overlain by a volcano-detritic sequence (Opemisca Group). Three important periods of tectonic deformation have been distinguished. The first one produced folds with north-south horizontal axes. The second one is responsible for the isoclinal east-west folds, and the associated regional schistosity. Reverse faulting contemporaneous with this period of deformation, produced two distincts effects. In some cases the faults cause a repetition of the stratigraphic sequence. Whereas in others the faults truncate second period folds. Domes and basins interference pattern are produced by the superposed effect of Di and D2 deformations. The motion of these two periods would be more or less contemporaneous. The deformation could be generated by rising diapirs of early plutons combined with the progressive formation of troughs by gravitational subsidence of denser strata. The rising diapirs of late granitoid plutons produces a wraparound of the host strata.

Jan 1, 1984

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By E. Sun

Tailings disposal is a significant consideration for the mining industry, with the majority of the ore processed in most mining operations ending up as tailings. Several tailings dam failure accidents have occurred during the past few years and mine tailings dam failures are occurring at relatively high rates. Tailings dam failure is disastrous with the serious damage and the loss of lives. To increase the tailings dam safety, a tailings dam monitoring and pre-alarm system (TDMPAS) based on the internet of things and cloud computing platform has been accomplished with the abilities of real-time monitoring of the saturated line, impounded water level, rain fall and the dam deformations etc. The TDMPAS has been applied in several mines in China and helped the mine engineers monitor the tailings dam safety and get warning information automatically and remotely in any kind of weather conditions. This work has been demonstrated the tailings dam monitoring and pre-alarm system (TDMPAS) is meaningful to monitor the tailings dam physical safety condition. The TDMPAS could be applied to monitor all the national tailings dams online in the future.

Jan 1, 2012

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By A Goldstone, T Maton

The Golden Cross Mine is located on the North Island of New Zealand, at the base of the Coromandel Peninsula, approximately 8 km northwest of Waihi. The project is operated as a Joint Venture with Coeur Gold New Zealand holding 800/0 and Viking Mining Limited with a 20% interest. The past open-pit and underground gold and silver producer has been in the reclamation phase of the operation for approximately 2.5 years and is now nearing completion. Although rehabilitation of the site is a regulatory requirement, the Closure Plan has been enhanced by the ongoing commitment of the Joint Venture to establish a sustainable land use for the site by commissioning engineered facilities designed to last for perpetuity. The Joint Venture identified six significant design features that were key to successful rehabilitation. These were the controlled placement of acid generating waste rock into engineered disposal sites; the design and placement of sealing layers over the waste rock disposal sites; the design and construction of diversion drains; the establishment and management of vegetation to protect the oxygen diffusion layer; a partial capping of the tailings to accelerate consolidation adjacent to the tailings dam embankment, and the implementation of a cyanide recovery circuit to recycle cyanide from the tailings prior to disposal. Another key to success for the project involved genuine consultation with all parties participating in the planning, evaluation, and consenting of the closure process at Golden Cross. The local and regulatory community has been widely represented in the Joint Venture's operating and closure plans throughout the history of the mine. Participants include: Regional and District Councillors and staff members, professional peer reviewers, environmental groups, local residents of the valley, and Iwi. This overall commitment to the project has resulted in a world-class rehabilitation program for the first modern metal-mine closure in New Zealand and we believe that collectively, the work done at Golden Cross is helping to set a standard for the success of future programs within the extractive industry.

Jan 1, 2000

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By Bertrand L. Johnson

Barite, the natural sulfate of barium (BaSO4), is the most important barium mineral. Normally it is white (opaque to translucent), but impurities sometimes render it yellow, gray, blue, brown, red, or black. Brown or red stains are commonly caused by iron oxide. Barite is unusually heavy (specific gravity, about 4.5); in fact, it is one of the heaviest of the nonmetallic minerals. It is brittle and fractures unevenly. The hardness of barite ranges from 2.5 to 3 but is usually about 3. It can be scratched by a copper coin. Pure barite contains 65.7 percent BaO and A.3 percent S03. Much of the crude barite ore mined, however, contains impurities; thus it has a lower content of barite and consequently less barium oxide. Commercial analyses show its total BaSO4 content. Barium also occurs in nature as the mineral witherite (BaCO3), which, however, is not common in the United States, and commercial deposits have been found only in California. Witherite is a yellowish-white, light-gray, or Kite mineral with a specific gravity of about 3, a hardness of 3 to 4, and an uneven to subconchoidal fracture.

Jan 1, 1941

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By Silver EA

The Finisterre Range on the north coast of Papua New Guinea is the uplifted forearc riagio.n. of a modern arc-continent collision. The core of the range is composed of the P- nisterre Volcanics, an Oligocene''-arc terrane. The southern flank of the range consists of a clastic sedimentary sequence which is an uplifted accretionary wedge and collision complex. This clastic sequence can be subdivided into three distinct units. To the south of aiid structurally below the Finisterre Valcanics are the Mebu beds, an Oligocene- $arly Miocene sequence of volcanolithic turbidites. The Erap Structural Complex is south of, and structurally below the Mebu 43eds. , It consists of three subunits; the 3rly Pliocene micaceous turbidites of the Sukurum unit, contemporaneous pillow basalts AF{ the Basalt unit, and Late Pliocene to Pleistocene volcanolithic turbidites of the -Nariawang unit. The Quaternary Leron Formation, a fluvial to shallow marine 'clastic unit, is the southernmdst. and structurally lowest unit of the clastic -sequence The Finisterre Range is dominated by a fold-and-thrust belt with most thrusts "dipping steeply N. Melange fabric _ is developed in the vicinity of major thrusts. "ffle thrust belt strikes NW, oblique to the regional convergence direction, but no strike-slip motion is observed along NW striking faults.

Jan 1, 1991

Every automatic citizen is an automatic recipient of a miner's right under the present Mining Act (Chapter 195), but this alone does not entitle any automatic citizen to mine for minerals on any land, even his customary group's land. Without complying with requirements of the Mining Act, any automatic citizen who engages in mining solely on the basis of a miner's right would be mining illegally. He would also be engaged in illegal mining if he mines on customary or other non-government land. Even if mining is legally pursued by an automatic citizen, he does not acquire ownership of minerals without first making the required royalty payments to the State.

Jan 1, 1991

By Scott Martin

This paper will discuss the challenges currently facing the mining industry. By sharing experiences gained in the CIM Leading in Mining Course, I will highlight what’s working, what’s not, what are the challenges, what are the concerns, what are the opportunities, what needs to happen. Specifically, I will discuss what is currently happening with leadership and leadership development in members’ own organizations, what skill sets are important to develop in different hierarchical groups and how comprehensive leadership courses like the leading in Mining course can help improve leadership within individuals and the industry. Leadership development is a process not an event.

Jan 1, 2014

By George Harrison

A great many labor leaders and others advocate shot-firers as the acme of relief for all the dangers connected with solid shooting, and where large quantities of powder are used in one blast in coal mines. Legislative bodies in several mining States have enacted laws providing for shot-firers in mines under such circumstances, the blasting to be done at night after the miners have left the mine. With all due respect to the opinions and honesty of purpose of these advocates of shot-firers, it is evident that a great many of them are not considering this important question in the broad sense it deserves and should be considered.

Jan 1, 2008

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By C. D. Shackelford, J. F. Muñoz, M. Vauclin, P. Rengifo, A. Suazo

The results of a field-scale study involving in situ leaching of copper ore tailings using sulphuric acid as the leaching agent, injection wells to introduce the leaching solution and extraction wells to recover the copper-enriched pregnant leaching solution are presented. The study was performed at an abandoned tailings disposal site using a battery of injection and extraction wells. The medium was characterized through the determinations of physical, chemical, mineralogical, and hydro-dispersive properties based on laboratory and field tests, including a tritium tracer test, a pumping test, particle size analyses, and hydraulic conductivity tests. Numerous horizontal strata with different hydraulic conductivities were identified. A previously developed model was used to simulate the leaching of copper ore tailings. Although the study confirms the feasibility of using in situ leaching for recovery of residual copper from tailings deposits, the efficiency of the technology depends significantly on the medium stratigraphy and hydraulic conductivity.

Jan 1, 2001