Search Documents

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the 5 potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum < potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the 5 potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as PH, reagent concentration, and floc size and density. Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By Eugene R. Rice

There are many methods for determining the meridian, but all of those in common use involve at least two separate observations, one for latitude and one for azimuth. Such observations made upon a south star at any hour are open to the objection of possible inaccuracy due to ignorance of the absolute refraction, and also to slow change in the altitude of the star when near the meridian. The method of observing a circum-polar star at elongation. besides requiring a separate observation for latitude, is open to the serious objection that clouds may obscure the star at the critical moment. Moreover, a tedious wait for the star to come to elongation is sometimes necessary. Many of us can recall &apos;long, cold, weary vigils, waiting for Polaris to reach elongation. For observing a circumpolar star at any hour, not only the latitude, but also the true time, must be known. This it is practically impossible to obtain, except in regions reached by the telegraph, and usually then one has to know the longitude also, in order to reduce " standard time" to " local time." The results obtained by this method, when the star is at culmination, are not very good, unless the true local time is absolutely known. The methods of obtaining the nleridian from the sun, by means of a solar attachment, or by direct observation, while good, are not absolute, by reason of refraction, change in declination of the sun, and small change in vertical angle, when the sun is near the meridian. For these two methods, latitude, time, and approximate longitude have to be known. In the method here described, only one observation is needed, and from it are computed azimuth, latitude, aud sidereal time. In other words, one call observe a circumpolar star—Polaris

Jan 1, 1911

The last one decade in India had witnessed phenomenal growth in the coal, lignite, iron ore, limestone and many other minerals. To meet the production of minerals, the energy requirement is also very high both in terms of petroleum products and electrical energy. Because of spiralling prices of crude oil and also of the electrical energy, attempts have been made by various mining companies to select energy efficient mining machineries (in underground and surface) mines, together with energy efficient mining and mineral processing operations. Mineral sector of India is working seriously in tune with the Planning Commission stipulations to conserve energy.Apart from energy use (both electrical and fossil fuels) in mining, it is also significantly contributing to the cost of mineral processing depending on the quality of ore/rock being processed. Over the years a number of studies have been initiated and implemented to reduce cost of energy bill. An attempt has been made to present the various aspects of energy conservation, Impact of Energy Conservation Act 2001, Relevance of energy audit, areas of energy consumption and conservation efforts, etc in this paper. The paper also deals with some of the case studies to show how energy conservation programs has been implemented in the Indian mineral sector.

Dec 6, 2010

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Andrew K. hg` Officer, A. L. Griffiths, J. Andrew Hindmarch, Gert Wittneben

Durban Harbour in South Africa is one of the continent’s busiest ports however the harbor entrance is currently too small for the new generation of container ships. There-fore it is to be deepened and widened by the National Ports Authority in the near future. An existing immersed tube tunnel carrying major sewer, water and other utilities under the harbor first needs to be removed and replaced by a deeper 4.4 m ID ser-vices tunnel. Construction of the deeper tunnel saw the first use of a slurry machine in South Africa and was required to negotiate grades up to 20%.

Jan 1, 2007

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961

By Ammar Henchiri, Godfrey McDonald

"Breakwater Tunisia S.A.’s Bougrine mine is located in a semi-arid region of Tunisia characterized with Triassic salt domes. Due to extensive agricultural land-use in the mine area, a zero-discharge tailings facility design and high water recycling rates to the concentrator were chosen to minimize the environmental impact to the surrounding area. The process water supply has an accumulation of naturally occurring salts due to high evaporation rates and the need to recycle 70% of the process water. The elevated salt content of the process water had an adverse effect on the efficiency of the flotation reagents, which led to the production of lower quality zinc concentrate.The impact of the water salinity on the zinc concentrate quality was documented by extensive laboratory testing. A feasibility study was prepared and a decision was made to install a reverse osmosis plant for desalination of the process water. A plant was constructed during 2000 which currently supplies up to 85 m3/hr of de-mineralized water, equal to approximately 45% of the total process water requirement. The salinity of the process water decreased from about ten to twelve grams per litre before installation to less than three grams per litre. Together with minor modifications to the concentrator circuit, Breakwater Tunisia has increased the zinc concentrate grade from 50% zinc to 55% zinc without compromising the zinc recovery rate of approximately 84%.This paper discusses the successful installation of a reverse osmosis desalination plant that allowed Breakwater Tunisia to improve the grade of the Bougrine mine zinc concentrate and thus increase the net smelter return.INTRODUCTIONBreakwater Resources Ltd., through a wholly owned subsidiary, Breakwater Tunisia S.A., acquired the Bougrine underground mine and related assets in September 1997. During the winter of 1997/1998, the company rehabilitated the mining equipment, modified the concentrator circuit, developed a new mine ventilation system and prepared a new mining production program. The mine was reopened on May 2, 1998 and was in commercial production as of June 1, 1998."

Jan 1, 2003

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

By A. Whillier

The decisive action taken by mine managements in recent years has been the main factor in bringing about the present downward trend in mine fires. A better understanding of the fundamental factors that govern the ignition and spread of fires. obtained as a result of investigations into mine fires, has provided useful guidance to production personnel. Similar investigations into fire-fighting techniques have assisted the Rescue Training Service and mines to institute more effective fire-fighting techniques. Some of the more important findings of recent investigations in these areas are outlined.

Jan 1, 1981

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By A. K. Majumder

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of coal fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of coal fines. The results obtained from this study revealed that among the parameters studied, drum rotation and feed solids concentration play dominating roles in controlling the yield and ash content of the clean coal. Mathematical modeling equations that correlate the variables studied and the yield and ash contents of the clean coal were developed to predict the performance of an MGS under different operating and design conditions. The entire exercise revealed that the MGS could produce a clean coal with an ash content of 14.67% and a yield of 71.23% from a feed coal having an ash content of 24.61%.

Jan 1, 2007

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

A Robust Chemically Enhanced Electrostatic Separation Technology Physical separation processes such as gravity, magnetic and electrostatic separations are extensively used in heavy minerals separations. Electrostatic (aka High-Tension) separation facilitated by the conductivity differences, in particular, is used for separating rutile from zircon. Although electrostatic separation is effective, it is not efficient. It suffers from separation efficacy issues owing to sensitive variables such as humidity, surface contamination, particle sizes and the temperature of the feed and other equipment parameters. The variations in the process conditions especially with humidity, temperature of the feed and the mineralogy and surface impurities can cause significant reduction in the separation resulting in production rate losses and product quality issues. Cytec Industries has developed chemical enhancement technologies for electrostatic separation for rutile -zircon separation from the heavy minerals. The major advantage of our technology is its higher separation efficacy in the first pass, substantial energy savings and most importantly its ability to do separation at room temperatures. The bolt-on nature to the existing electrostatic also an added feature that reduces the capital expenditure significantly. The separation efficiency between rutile and zircon was increased as much as 8 - 11 per cent compared to control. It is possible to extend the chemical enhancer technology to problematic feeds and other mineral systems that are not easily amenable to conventional electrostatic separation.

Sep 13, 2010

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By A. Patri, D. S. Nimaje

Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before implementation of any wireless system, the variable path loss indices for different workplaces should be determined. This helps in better signal reception and sensor node localization, and also improves the method by which miners carrying the wireless devices are tracked. This paper proposes a novel method for determining the parameters of a suitable radio propagation model, which is illustrated with the results of a practical experiment carried out in an underground coal mine in southern India. The path loss indices, along with other essential parameters for accurate localization, have been determined using the XBee modules and ZigBee protocol at 2.4 GHz frequency.

Jan 1, 2015

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009