Search Documents

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By R Bezuidenhout, J K. Claflin, S R. La Brooy, G M. Wardell-Johnson, A M. Claflin

Best practice gold (Au) recovery is not an accident. It is the result of proper operation of the adsorption circuit using good quality activated carbon. A conventional carbon ‘regeneration’ kiln cannot process carbon fouled with floatation chemicals and achieve best practice gold recovery. A high temperature, controlled atmosphere carbon ‘reactivation’ kiln is required. Carbon circuit design allows for low quality carbon by increasing the carbon advance rate, carbon inventory and setting an easily achieved and commercially prudent solution tails target of typically 0.02 ppm Au. These design criteria are important to ensure the commercial success of the gold operation in the first instance. Most carbon ‘regeneration’ kilns will produce carbon of sufficient quality to achieve a 0.02 ppm Au solution tail in the absence of flotation reagents.Best practice recovery is considered less than 0.005 ppm Au in solution reporting to tails. If the carbon is heavily fouled, as it will be if used for flotation leach circuits, then a conventional carbon ‘regeneration’ kiln cannot achieve world’s best practice recovery no matter how much carbon is advanced. World’s best practice gold recovery requires a carbon ‘reactivation’ kiln and the whole of the carbon circuit operated optimally.The competing reactions occurring in a carbon ‘reactivation’ kiln are presented and discussed in terms of kiln design and operation. New industrial and laboratory findings are presented to fill gaps in the body of knowledge and identify that a large reduction in residence time at temperature will not significantly impair reactivation, but can significantly reduce the size and cost of the kiln or permit significantly increased carbon throughput.The carbon circuit performance is modelled in terms of gold adsorption, as a function of carbon reactivation using ‘simulation of carbon-in-leach/carbon-in-pulp circuits’ (SIMCIL). An optimum carbon advance rate is identified as a function of optimum carbon ‘reactivation’ kiln operation to achieve 0.005 ppm Au in the tails solution. A conventional carbon ‘regeneration’ kiln is compared to a state-of-the-art carbon ‘reactivation’ kiln in terms of reactivation performance and gold recovery.CITATION:Claflin, J K, La Brooy, S R, Wardell-Johnson, G M, Bezuidenhout, R and Claflin, A M, 2017. Optimising carbon reactivation kiln operation, in Proceedings MetPlant 2017, pp 346–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By K. W. Lee, C. Pound, J. Carmody, L. Petersen, C. Nelson, J. G. Cai

The feasibility of developing the Underground Science City below the Kent Ridge Park has been investigated. The primary aim of the study has been to explore the possibility of creating underground space to house a new community of research laboratories and offices. The investigation represents the first such study undertaken in Singapore for a non-military underground facility. The paper describes the geology of the Underground Science City site and illustrates the layout and plan of the Underground Science City. The geology and rock mass below the Kent Ridge Park is generally favorable for the development of an underground cavern complex. Underground Science City can be potentially developed housed in a cavern complex. Several potential development schemes are studied; with various combination of deep/shallow mined caverns of different span sizes and access options. The preferred scheme is shallow, mined room-and-pillar caverns with large spans and shaft accesses at both existing surface Science Park 1 and Science Park 2. The scheme can be potentially expanded laterally to create more underground space for new Underground Science Cities at Kent Ridge area.

Jan 1, 2001

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

At Appin colliery, geological structural analyses and investigations of roof conditions suggest roof failure may be attributed to vectorial stresses acting on underground openings, and inducing movement along inherent discontinuities in the surrounding rocks. Certain complex joint and fracture patterns tend to exhibit the effect of this movement resulting often in local deterioration in natural support.The following conclusions are drawn.1. Roof failure is related to the inherent nature of the roof rocks, the presence of mechanical discontinuities, and the vectorial stresses imposed upon it.2. Roof failure is not necessarily related to the statistically most prominent jointing.3. Colliery development approximately parallel to the direction of the statistically most prominent jointing sometimes results in favourable roof conditions.4. The maximum principal stress is the resultant of those vectorial stresses acting upon a mine opening and may be inferred from roof adjustments to those stresses after mining.5. Statistical analyses of jointing in the mine workings can provide clues to the tectonic force or forces which have been regionally or locally influential.6. There is a probable relationship between mining induced fracturing, jointing, and micro-fractures in quartz grains, within the sediments of the mine roof.

Jan 1, 1970

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

Despite a long history of production of industrial minerals and rocks, New South Wales still offers significant opportunities for exploration for and development of these minerals. Exploration for opal, sapphires, and zeolites in the State has been particularly encouraged by pioneering geological studies by the Department of Minerals and Energy, which have resulted in the development of important new geological concepts and exploration techniques. Large areas with potential for these minerals have not yet been tested. In the case of sapphires, the studies have identified a new type of deposit which is'the source of most of the sapphires mined from alluvial deposits. Recent price increases for heavy minerals, a re-evaluation of previous exploration in coastal regions, and a recognition of suitable environments in inland New South Wales have stimulated renewed exploration both onshore and offshore and have led to increased production. Significant potential also exists for development of a number of other minerals, including: topaz, which occurs in large, unusual and perhaps unique deposits in northern New South Wales; dimension stone (particularly granite); bentonite; diatomite; and silica for metallurgical use. Potential also exists for development of construction material resources, particularly construction sand, which is in short supply in the Sydney region.

Jan 1, 1989

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By Albaharna O. T., Argyropoulos S. A.

"This paper describes the development and the implementation of process control in a variety of instruments used in metallurgical laboratories. These instruments are used for different research projects in extractive metallurgy. Hardware and software aspects for this implementation are described and analyzed. Extractive metallurgy applications where process control was .used are presented. IntroductionMicroprocessors are invading almost every area of our lives and are turning up in unexpected applications. A great deal of new equipment which is coming into the market have built- in microprocessor systems. Nevertheless, the area of upgrading existing processes has been slow to develop. There are a variety of reasons for this, and many of these are economic. One of the principal reasons, however, is the general reluctance on the part of many organizations to commit a strong effort to put this new technology into their existing processes.Microprocessor systems developed ""in lab"" are capable of not only measuring thermophysical events which are taking place in metallurgical furnaces, but simultaneously controlling these furnaces. In this paper software and hardware aspects in the implementation of microprocessor control for resistance and for induction furnaces are presented. In addition to this, metallurgical results are given from experiments where this furnace control was applied."

Jan 1, 1989

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

The results of self potential geophysical surveys conducted over base metal prospects near Orange, Goulburn, and Wellington, N.S.W., indicate that this rapid and inexpensive exploration procedure merits wider application within eastern New South Wales, and in similar environments elsewhere.

Jan 1, 1973

The University of New South Wales (UNSW Australia) has been a world leader in the development of innovative virtual reality technologies over the last 15 years. AVIE (Advanced Visualisation and Interactive Environment) was developed by iCinema as a collaborative venture between UNSW?s Faculties of Engineering and the College of Fine Arts. This is the world?s first 360°-surround, virtual reality (VR) stereo projection theatre system. The School of Mining Engineering at UNSW Australia has developed 18 different virtual reality modules aimed at mine safety training and mining engineering education. These modules are being regularly used in both the mining industry and the university. The School of Mining Engineering is continuously involved in the development of different modules. Research is also currently being conducted on the implementation of other technologies into this environment. Artificial intelligence (AI) and fuzzy logic are tools that the authors would like to consider implementing in future module development. This paper will review current research in both these areas and consider options for applying these technologies.

Jan 1, 2014