Search Documents

By Tian Sugui

By direct aging treated, creep properties measurement and microstructure observation, the influences of the direct aging treatment on the creep behaviors of Hot Continuous Rolled GH4169 superalloy are investigated. Results show that the creep resistance of Hot Continuous Rolled GH4169 superalloy may be obviously improved by directly aged treatment. Under the applied stress of 700MPa at 660, the creep lifetime of the alloy is enhanced to 126h from 60h. During hot continuous rolling, the deformation features of the alloy are the twinning and the double orientations slipping of the dislocation activated within the twinning regions. After direct aging treated, the alloy displays a smaller grain size, and the finer g² phase is dispersedly precipitated in the matrix of the alloy, which is thought to be a main reason of enhancing creep lifetime of the alloy.

Jan 1, 2010

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001

By E. Chin

The only economically significant mineral exploited in Banglades - during 1981 was natural gas. Nitrogenous fertilizer production was important to the agricultural sector and was totally dependent on the natural gas for fuel and raw material. Domestic cement plants were also fu pled by natural gas. The flat river-delta terrain for most of Bangladesh makes the potential for discovering major mineral deposits poor. No large deposits of metal ores have been found and only in the small hilly southeastern section of the country is there even much chance of finding any. Heavy mineral sand deposits may eventually be exploited along the Chittagong coastline. There is a good potential for crude oil discoveries. The Bangladesh economy has been heavi¬ly subsidized by billions of dollars of foreign aid since the country's inception. A World Bank report recommended total aid needs of over $2.6 billion in fiscal year (FY) 1980-81. It received commitments for barely over one-half that amount.

Jan 1, 1983

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

By D Wyatt, J Domenico, W Kow

Over the past few years developments in heavy minerals processing have concentrated on the mineral separation portion of the business. The best example of this would include new developments in rare-earth magnetic separators and associated flowsheet modifications. Except for some minor modifications in spirals, the æwetÆ side of the separation business has lagged behind the ædryÆ side. Basic concentrator design has not changed in 20 years. Recent pilot trials by Outokumpu Technology have shown the benefits of a new gravity flowsheet that combines density separation and spiral concentration on a variety of heavy mineral deposits. This concept is already well utilised within the iron ore industry. The synergistic combination of these two technologies allows smaller, simpler, and controllable gravity concentrators to be built while providing equivalent or better grade and recoveries of valuable heavy mineral. This is contrasted to the all spiral flowsheet characterised by the diminishing returns of multiple stages of spirals and associated recirculating loads. Examples of the flowsheets and associated benefits will be presented from a variety of cases.

Jan 1, 2001

By C. Kloppers

The aim of this investigation was to reduce the cost of primary steel de-oxidation by substitution of aluminium primary de-oxidation with a practice that uses carbon. The cost of carbon is four times lower than that of aluminium. The application of carbon would directly result in raw material cost savings. Investigations were conducted at Iscor?s Newcastle steel plant on various steel grades. Specific production aspects were emphasized to ensure that the cost savings accrued would not create secondary expenses. These production aspects entailed: ?Yields on de-oxidation elements ?De-oxidation capabilities ?Alloying yields (Mn and Si) ?Carbon-pickup ?Nitrogen-pickup ?Temperature loss during tap ?Steel cleanliness ?Slag morphology. This project proved that carbon de-oxidation, apart from reducing de-oxidation raw material cost due to cheaper raw materials being used and lower consumption rates, resulted in steel that is cleaner and has lower nitrogen concentrations. Carbon primary de-oxidation has been implemented at Iscor?s Newcastle plant on a large range of steel grades, ranging from ultra-high carbon (> 0.60% C) to ultra-low carbon (< 0.03% C) grades. A net saving of between R100 000 and R200 000 per month was achieved.

Jan 1, 2001

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By U. Paschedag, H. Bussmann

"Bucyrus manufactures the most comprehensive product portfolio of mining equipment worldwide. Its mission is to have a positive, lasting effect on our world. Bucyrus makes sustainable development a fundamental way of doing business through economic, environmental and social initiatives that support, educate and benefit our employees, customers, shareholders and other stakeholders. Our participation in GRI (Global Reporting Initiative), a network-based organization that has pioneered the most popular sustainability reporting framework will be discussed as well as examples will be given on each major field of engagement. Two examples from surface machinery are most fuel efficient haul trucks as well as the Highwall mining system which allows access to coal reserves which are lost not making use of this kind of system. Two examples from underground machinery are Bucyrus’ automated plow systems for the mining of medium and thin coal seams with minimum rock and Bucyrus’ intelligent CST drive system for high-powered armored face conveyors (AFCs) for efficient use of energy."

Jan 1, 2011

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By G. R. Smith

Critical and strategic metals are often present in small quantities in low-grade domestic ores. When these ores are leached, the resulting solution usually contains the metals in very dilute quantities. Selective electrowinning from dilute electrolytes was investigated by the Bureau of Mines. A metal deposit containing 84 pct nickel was electrowon from the leach solution of a complex domestic ore bulk flotation concentrate originally containing approximately 2 wt-pct nickel. Key to achieving accelerated deposition rates, in the case of dilute solutions, is the rapid movement of the electrolyte through the electrowinning cell. Pure, synthetic nickel electrolytes were used to establish deposition parameters, and to optimize electrolyte velocity or mass transfer rates. Hydrodynamic and electrodeposition parameters for both the synthetic and leach electrolytes are presented and the experimental research described. Selective electrowinning appears to offer a viable alternative to physical separation methods to obtain separate metal "concentrates" from low-grade ores.

Jan 1, 1983

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems include: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of environmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental difficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 9, 1980

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By O Haavisto, N Khajehzadeh, L Koresaar

Online analysis of metal content can be used to optimise the grade and recovery of a flotation circuit. Compared to conventional laboratory analyses, the benefit of an online analyser is the speed of the measurement, therefore disturbances (eg changes in feed grade and decrease in recovery) can be reacted to in real time by an operator or automatic process control system. In some cases traditional X-ray fluorescence analysers can be applied to silica analysis in iron ore when the SiO2 grades are high enough and have a negative correlation with iron; however, generally a laser-induced breakdown spectroscopy (LIBS) analyser is more suitable for low Z elements.The Outotec Courier 8&#174; analyser is a LIBS based analyser able to measure elements starting from lithium (Z = 3), thus being able to measure impurities; eg silica and aluminium directly in iron ore slurries. Besides online elemental analysis, the analyser can be combined with optical measurements for rapid continuous measurement of each sample line. Laboratory testing has also shown potential for mineralogical analysis using the combination of LIBS and reflectance spectroscopy.CITATION:Koresaar, L, Khajehzadeh, N, Haavisto, O and Timperi, J, 2017. Online elemental and mineral measurement of slurries in iron ore beneficiation, in Proceedings Iron Ore 2017, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By Mansour Asri, Philippe Somogy, Youssef Daffi, Amor Karim

Very few cases of Cast Blasting use in phosphate mining are reported. However, in open-cast coal mining, Cast Blasting is a common practice. And yet, the geological structure of both types of deposits is similar. Accordingly, advantages for phosphate open-cast mines are manifest, especially as future conditions of phosphate deposits fit quite well with the approach.

Jan 1, 2015

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016