Search Documents

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By G. E. Agar, W. B. Kipkie, V. K. Drylie

"This paper describes mineral processing test work on drill core samples from an ilmenite deposit in Terrebonne County just north of Montreal.Mineralogical examination showed that the intimate associa¬tion between ilmenite and hematite precluded their separation. The maximum concentrate grade was therefore limited to 22.9% Ti. Liberation of gangue from the hemo-ilmenite grains occurred around 400 µm, a size which proved to be too coarse for recovery by flotation.Other physical separation techniques, such as elec¬trodynamic, magnetic and jigging, were tried in order to take advantage of the relatively coarse liberation size. An all-flotation procedure and a combination of jigging and flotation yielded similar separations.IntroductionInco Metals Company, through its subsidiary Canico, optioned an ilmenite deposit in Terrebonne County, just north of Montreal, and conducted a drilling campaign to confirm previous geological assessments of the deposit and to provide core samples for mineralogical study. Parts of these core samples were used for mineral processing studies, which will be described in this report. The objective was to identify suitable upgrading procedures, to determine the optimum combination of concentrate grade and recovery, and to provide suitable batches of concentrate for further treatment."

Jan 1, 1980

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By A. Erickson

The effectiveness of a loader-mounted fan on diesel vehicles combined with natural convection for ventilation of a dead heading (the patented Janelid system) was investigated experimentally. The results were obtained using CO2 as a tracer gas in a 1/4 scale model heading. Buoyant forces were scaled to establish similarity with full scale. For a loader moving in a typical load-haul-dump cycle, the loader-mounted fan reduced the tracer gas concentration by 26 percent compared with a reduction of 32 percent for a jet fan of four times the flow capacity.

Jan 1, 1981

[Chairman ZAY JEFFRIES, Vice-chairman S. SKOWRONSKI, Chairman WILLIAM M, CORSE, Secretary Executive Committee J. R. FREEMAN, JR., Local Section G. E. JOHNSON R. S. ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C. BAIN, Journal Committee L. W. SPRING SAM TOUR, Papers Committee F. L. WOLF H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G. H. CLAMER, Philadelphia W. A. SCHEUCH, Chicago R. F, Woon, New York Papers Committee S. SKOWRONSKI, Chairman F. H. DIx, JR.-Aluminum E. R. DARBY-Bronze C. S. WITH ERELL-Copper H. A. BEDWORTH-Brass W. K. FRANK-BRONZE F. W. HARRIS-Copper R. L. SUHL-Nickel H. M. ST. JOHN--Foundry Metallurgy R. S. DEAN-Theoretical Metallurgy]

Jan 1, 1928

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007

By Gordon King

The City of Atlanta Water Department required the construction of a two sludge tanks and a wet well at the existing Chattahoochee Water Treatment Plant. Western Summit won a design build contract to build the project and proceeded to evaluate the wet well size options, and construction procedures. The final design required the construction of a 1 million gallon tank. The proximity of the underground tank to adjacent roads and existing plant structures ruled out laying back the excavation. As a result a tied back sheet pile retaining wall was initially proposed.

Jan 1, 2003

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

By Mostafa Benzaazoua

Les remblais en pâte cimentés sont de plus en plus utilisés dans les exploitations minières souterraines. Une autre alternative d?utilisation du remblai en pâte consiste à le pomper et à le stocker dans des empilements de surface. En plus d?avoir des avantages d?un point de vue de stabilité physique des ouvrages, le remblai en pâte cimenté en surface permettrait également de stabiliser les contaminants dans la matrice du remblai à l?aide du processus de solidification et de stabilisation. Dans cette étude, des remblais en pâte constitués d?un résidu minier sulfuré renfermant beaucoup d?arsenic et de différents liants ont été testés afin d?évaluer la stabilisation des contaminants dans la matrice de remblai. La méthode utilisée pour évaluer la stabilisation et la solidification des contaminants est le test de lixiviation en extracteur de Soxhlet. Les résultats géochimiques issus de ces essais ainsi que la caractérisation chimico-minéralogique des remblais lixiviés ont été analysés pour comprendre les phénomènes chimiques présents dans les remblais durant le temps de cure. Les résultats obtenus montrent que les sulfures présents dans les remblais étudiés (pyrite FeS2 et arsénopyrite FeAsS) s?oxydent et provoquent la dissolution des hydrates les plus vulnérables (dissolution de la portlandite Ca(OH)2 et/ou décalcification des gels CSH). Le calcium produit permet de précipiter les sulfates (essentiellement sous forme de gypse plus ou moins hydraté) et l?arsenic sous forme d?arséniates de calcium plus stables. Les différents liants utilisés donnent des résultats différents en termes de stabilisation et de solidification qui seront discutés dans cet article.

Nov 1, 2002

By A Webster, T Murphy

Block cave mining, in its broadest sense, has transitioned from an orebody/rock mass determined method of extraction, to a low-cost and high production mining method that may be applied to any large ore deposit. This inherently means that caving is now required in more complex rock mass conditions where assistive damage, through preconditioning, may be necessary. This requires comprehensive understanding of the geology, and its interwoven relationship with geotechnical parameters, and is made more challenging due to limited exposure in block cave mines. Limited mine development throughout the cave volume equates to a heavy reliance on drilling data in terms of observations, modelling of the mine geology, and collection of geotechnical data. This translates as increased uncertainty of geological and geotechnical models and has potential to impact significantly on the ability to make informed decisions in the design and operation of the cave mine.Modelling of cave propagation behaviour requires a complex, coupled system of draw of material, flow of material through the cave stocks, and propagation of the cave-back assisted by autogenic stress-related breakage of the rock mass, manifested as seismicity. The role of geological features in the process of cave propagation is not well understood and requires evaluation on a mine-specific basis, given the diversity of geological controls/settings of ore deposits and local variability of stress fields.Seismic monitoring systems can elucidate key geological features and domains, as heterogeneous seismogenic activity is observed ahead of the advancing cave-back. The observations made from analysis of seismic monitoring data may have potential to be used as a validation tool for numerical modelling of predicted cave behaviour in similar geological settings (eg next lift/panel).Understanding of the geological structure, at all scales, is critical to optimise the design and operating decisions made in a block cave operation. At present, intermediate-scale structure, anisotropy, mineralogy and model uncertainty may be neglected or under-represented despite their likely significant role in the mechanisms of cave propagation.Insights from an analysis of the Ridgeway Deeps block cave mine are discussed in this paper.CITATION:Murphy, T, Webster, A and Chitombo, G, 2016. Beyond rock mass characterisation – the impact of geology on block cave mining, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 861–872 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By Steven W. Hunt, Isabelle Lamb, Steven B. Fradkin

Groundwater control is generally an important consideration and significant source of risk during most tunneling projects. Proper baselining of groundwater conditions requires: 1) a thorough understanding of the geological environment; 2) a focused site investigation; 3) identification of construction and adjacent property damage risks associated with inflows and short and long term piezometric level changes; and 4) consideration of contractual issues including restrictions on means and methods and pay items for associated work. This paper provides an overview of groundwater baselining issues and risks based on selected design studies and construction case histories.

Jan 1, 2005

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001