Search Documents

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

By J. A. Hayes

For over a decade the Osterberg Load Cell has been successfully used to determine the shear capacities of drilled shafts. Since the test method measures side shear directly, analytical complications due to the influence of end bearing resistance are removed. The data suggest that the side shear component of a drilled shaft&apos;s capacity is often more significant than end bearing. Given the interest in the use of side shear in drilled shaft design in compressible materials, it is important to examine factors that can influence capacity. We have found that some factors widely believed to influence capacity, such as slurry type, are not as important as commonly thought in most materials. Factors that are not usually considered as important, such as casing use, hoop spacing, concrete slump, concrete additives, spacers and rebar clear cover, seem to be more influential with respect to side shear capacity. For example, substantially lower than predicted shear resistance can occur when the rebar clear cover is small with respect to the cage diameter. We observe this most often in fine-grained cohesive soils. This effect can be exaggerated if the rebar cage has tight hoop spacing, if the concrete has low slump and if the hole is not straight. We have also noted that improper use of temporary casing can have a dramatic effect on side shear resistance. In some cases we have observed tested shear capacities reduced to less than 5% of either predicted or available shear values.

Jan 1, 2003

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By P. J. Bhonde, R. D. Angal

Conventionally low carbon ferromanganese is manufactured globally by refining high carbon ferromanganese in liquid state. This process is an expensive and lengthy technique. Hence, the present work was undertaken with the objective of understanding the feasibility and kinetics of the solid state refining of ferromanganese. The process involved transformation of carbon rich carbides viz. Mn3C2, Mn7C3 into metal rich carbide i.e. Mn15C4, Mn23C6 by subjecting the alloy powder to a flowing stream of carbon dioxide. Effect of the process governing parameters such as time, temperature, particle size, pressure on the extent of decarburization was studied. Without any loss of manganese in the form of fumes or slag, it was observed that, there was substantial reduction, viz. 65 per cent in the total carbon content, by this technique. Subsequently, the process was investigated to find out the mechanism of carbon removal. Depending upon the temperature and the particle size, it was found that the rate controlling mechanism changes from chemical reaction control to product layer (ash) diffusion control. The activation energy for each of the aforesaid mechanism was computed. The values thus obtained substantiated the aforesaid mechanisms.

Jan 1, 2004

By R. E. Jones

"Crusher sizing and application in mining operations is the selection of a crusher or a series of crushers to reduce run of mine ore to a size suitable for either autogenous or conventional grinding. It is important that the crusher or crushers be sized to operate within the range to which they have been designed. By the range to which they have been designed, we mean that the reduction ration must be held between specified limits. Reduction ration is the relationship between feed size to product size.In todays plants reduction is usually accomplished in three stages by primary, secondary and tertiary crushers.Primary crushers are either jaw or gyratory and are designed to handle run of mine feed at an open side setting of 5-1/2” to 7”. Reduction ration should not exceed 7 to 1.Jaw CrushersThe model size of a jaw crusher signifies the feed opening. A model 60 x48 jaw has a feed opening 60” wide by 48” long. The 48” is the dimension between the top of the swing jaw and the top of the stationary jaw. The 60” is the width between the two side frames. The crusher open side setting is the discharge opening at the bottom of the crushing chamber with the jaws in an open position. When corrugated jaw plates are used, the open side setting is measured from tip of one jaw plate to the valley of the opposite jaw plate. If a jaw crusher has a 6” open side setting with a 1” jaw motion, you could also say it has a 5” closed side setting."

Jan 1, 1974

By G. Deschênes

The Eleonore property (James Bay district of Northern Québec), owned by Goldcorp, hosts gold within stockworks of quartz-tourmaline-arsenopyrite veins and veinlets contained within microcline (potassic alteration) and brown tourmaline replacement zones. The preliminary investigation to recover gold from drill core samples showed that flotation followed ultrafine grinding and cyanidation is the preferred option. Ultrafine grinding is used to liberate gold finely disseminated in sulphides. The flotation concentrate used in the investigation had a P80 of 11 microns and contained 75.5 g/t Au, 5.0 g/t Ag, 10.3% S, 0.07% Cu and traces of antimony (0.03%). The mineralogical characterization showed the presence of 65% gangue minerals, 23% pyrrhotite (hexagonal), 9.6% arsenopyrite, 2.2% pyrite and 0.08% chalcopyrite with trace amounts of galena (0.05%) and sphalerite (0.03%). Gold was in the form of native gold and electrum. A straight cyanidation conducted at pH 11.0, DO of 3-5 ppm, 2000 ppm NaCN, 20 C 72 hours extracted 97.0% Au and consumed 31.5 kg/t NaCN. The equilibrium was reached within 24 hours. Increasing the dissolved oxygen to 16 ppm reduced the consumption of cyanide to 22.0 kg/t with 96.7% Au extraction. A 16-h pretreatment with 2.0 kg/t lead nitrate, followed by a 24-h cyanidation reduced the cyanide consumption to 6.0 kg/t with a gold extraction of 97.5%. Increasing the lead nitrate addition to 6.0 kg/t reduced the cyanide consumption to 1.2 kg/t by passivating the surface of pyrrhotite. The gold extraction remained at 97.0%. It was possible to decrease the concentration of cyanide to 800 ppm NaCN without compromising gold extraction. The associated cyanide consumption was 1.2 kg/t NaCN. The passivation of gold grains was an issue when the cyanide concentration was decreased to 550 ppm NaCN. The gold extraction decreased to 92.2%. The average lime addition for all the tests was 7.4 kg/t and the average silver extraction was 80%. Efficient cyanidation of an ultrafine sulphide concentrate with only 800 ppm NaCN represents an advance in leaching of ultrafine sulphide concentrates.

Jan 1, 2013

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988

The Martha deposit is an economic giant epithermal gold deposit, with mined and unmined resources of more than 218 000 kg (7 Moz) Au. The Au-Ag, base metal sulphide-bearing quartz lodes in the Martha deposit form an extensive braided pattern within hydrothermally altered andesite wall rock. There are five main quartz lodes: 1.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Martha, 2.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Welcome, 3.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Edward, 4.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Empire, and 5.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Royal. &nbsp; Information from historic mine plans and reports has been used to determine the depth distribution of economic ore within the Martha deposit. Economic ore (average of 10 g/t Au) in the Martha underground mine was at a maximum width and strike length between a vertical depth of 160 and 350 m. Below this depth the quartz-sulphide lodes continue, but the grade declined to sub-economic grades (&lt; 4g/t Au) at about 575 m depth and economic ore shoots were localised, mainly on the hangingwall side of the lodes. Samples from exploration drill holes indicate that this decrease is associated with a depth zonation from electrum-bearing Zn-Pb-Cu-Ag sulphide ore (average 10 g/t Au) to sub-economic (&lt; 2 g/t Au) electrum-poor Zn-Pb sulphide mineralisation.

Jan 1, 2006

By P. J. van der Walt

Some 30 years ago exposure to dense-medium separation in South Africa, culminated in the adaptation of the process for the treatment of -0.5 mm fines. The first commercial plant at Greenside Colliery apparently operated for some 18 years. Three further plants followed, including one treating tin ore. It is gratifying to learn, therefore, that there is renewed interest. The objective of making the process easier to operate (?more practical??) is commendable but the cumbersome technical approach could be counter productive. Perhaps a brief outline of the original thinking might be helpful when analysing the problem.

Jan 1, 2003

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By David Cole, Paul Cooper, Dale Preece, Jerome Stofleth

The Explosive Destruction System (EDS) has been designed at Sandia National Laboratories for the disposal of chemical munitions (phosgene, mustard gas, sarin etc.), many dating back to World War I. EDS is a portable system that is trailer mounted and consists of a vessel into which a chemical munition can be loaded and opened for neutralization with linear and conical shaped charges. Gases are contained within the sealed chamber. The linear shaped charges split the munition in two and the conical shaped charge (CSC) is aimed at the explosive burster, in each munition, which is detonated by the resulting shaped charge jet, Toxic chemicals remaining in the vessel following detonation are neutralized and disposed of. This paper documents the development of a new CSC needed to reliably detonate explosive bursters in an expanding array of chemical munitions that are beyond what the EDS device was originally designed to eutralize. Design of this new CSC was controlled by the need to deliver energy above the detonation threshold into the explosive after penetrating the outer steel casing, fluid, the burster casing and finally the explosive. Design considerations were driven by jet conditions at the steel/explosive interface inside the burster. Parameters to consider in CSC design include: 1) diameter, 2) liner thickness, 3) liner position in body, 4) explosive weight, and 5) liner shape or interior (apex) angle. The effects of these parameters on final CSC performance are examined in detail. CSC’s that meet the design specifications have been manufactured and tested. The performance of these charges are compared with the original design requirements.

Jan 1, 2002

By F. G. Crack, R. V. Ramani, R. L. Frantz

Management for mine construction and development differs from that needed for routine mine production and maintenance. An integrated approach to managing mine development projects must consider contract documents; management organization of a project; the project manager&apos;s role and the field supervisor&apos;s responsibility; and the use of scientific techniques for planning, scheduling, executing, and controlling projects. Professional project management encompasses the following: • Preparing contract documents that establish technical and financial schedules, and detail the responsibility for the physical work commitment. • Developing a project&apos;s organizational structure, to clearly define the roles of the project manager and the field supervisors. • Establishing project management and field supervisor relationships, to avoid ambiguity in assigning responsibility and to ensure desired project progress. • Using management science techniques, particularly networking techniques such as the critical path method for planning scheduling, executing, and controlling projects. Project Versus Production Management Project management differs from routine production management in the following ways: • Uniqueness: A project is unique. Production operations tend to be repetitive. The magnitude of one-time capital expenditures for many facets of mine development warrant special skills and attention. These professional project development skills must already be available by prior experience in the management team. • Personnel: In projects, personnel are usually assigned on a specialty basis and frequently change with the project activity. On the other hand, production personnel work together, more or less permanently. • Management Structure: In a project there may be several staff-line relationships that are not clearly defined and change with changing project activities. In a production situation, the lines of communication and authority are usually well defined. • Time Frame: A difference between project and routine production management is that project activities have comparatively less well defined durations and often tend to be relatively short-term. Production usually has both long-term and short-term plans and well defined long-term and shor-term goals. In project management, formal, critical, short-term reviews are frequently required. In production management, five year plans can be formally adjusted quarterly and annually. Short-term weekly or daily reviews can be informal. • Response to Delays: Delays in a development project may occur without anyone being immediately aware of their existence or suspecting the magnitude of consequence. In contrast, any delays in the production process can be easily identified from prior results comparison. Additionally, the response is quick, usually in a set routine. This can be traced back to the management structure and personnel. • Control Techniques: Measurements of project progress for control are not easily made due to the variety of activities that are carried on at the same time by different work groups. The yard-sticks of performance measurement for individual activities, let alone for the total project, are not easily established. However, due to the difficulty in detecting project delays, a workable control system is vitally important to a project manager. To apply a scientific project control technique such as "management by exception" requires specific planning and monitoring from the project manager for each activity in the project. Production and productivity are quick and effective yard-sticks of measuring performance in a routine operation. Control techniques required in production management usually revolve around these measures. Construction Contracts The construction contract is an important document that establishes contract scope, technical and financial details of the work, and achievement deadlines. It may also serve as the contract document to pay for work done and to verify field progress with planned progress. In practice, it is a good idea to develop a job-specific contract. This whole area is replete with legal precedence and procedures, and it is not the intent here to deal with the intricacies of establishing a contract document. But it is necessary to have an understanding of major contract types. Construction contracts are extremely important legal documents. They may vary in work specifications and enforcement of the provisions. Due to their nature, they must be composed with legal help and will take some time to compile. Even with all the precautions and provisions, it is not uncommon to find owner and contractor disagreeing. Therefore, it is important to include a way to resolve any difference quickly and to incorporate aspects of the contract as part of an overall management control tool for efficient project management.

Jan 7, 1982

By S F. Simmons

At Broadlands-Ohaaki geothermal system, TVZ, mineral distribution patterns in geothermal wells are analogous to those in epithermal veins. Fluid flow through geothermal wells is focused over vertical intervals &gt;500 m with discharge at rates up to 90 l/s. Focused flow at similar rates also occurs in natural systems where hydrothermal eruption vents provide enhanced vertical permeability. These vents are commonly aligned with the tectonic fabric, indicating fault control at depth. We suggest that host rock strength and structural context exert significant control on the hydrological regime conducive to epithermal mineralisation.

Jan 1, 2005

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016

By M. J. Miller, N. Ripepi, M. Karmis, J. M. Conrad

Unmineable coal seams present an opportunity to sequester carbon dioxide emissions from power plants, while enhancing the recovery of coalbed methane. Injected carbon dioxide is adsorbed and stored on the coal surface while releasing methane that can be commercially recovered. Carbon sequestration, therefore, allows the utilization of unexploited mineral resources while reducing “greenhouse” gas emissions. This paper presents the feasibility, efficiency and enhanced recovery potential of coalbed methane production using carbon dioxide sequestration in the Central Appalachian Basin. The focus of research is on geological characterization of unmineable coal seams in Central Appalachia and the corresponding carbon dioxide storage capacity. Virginia Tech and Marshall Miller & Associates, Inc. conducted this research under the Department of Energy’s Southeast Regional Carbon Sequestration Partnership program.

Jan 1, 2006

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites. The objective of this study was to compare two mines, each affected by this pillar load transfer mechanism, and to show how this interaction affected underground workings by the installing and monitoring underground instrumentation. At mine site A where the overburden was 1,000 ft, the innerburden thickness was less than a pillar width (40 to 45 ft), overlays of the mine layout show pillars were not superpositioned, excessive roof to floor convergence was measured, and pressure readings indicated pillar core loading only. At mine site B, the overburden was approximately 555 ft, the innerburden thickness was approximately 105 ft, overlays of the mine layout show pillars were superpositioned, minimal roof to floor convergence was measured, and pressure readings indicated a skin loading only.

Jan 1, 1988

By Joseph J. Mgumbwa

Pillars are any structures left between two or more underground openings. The stability of pillars is normally considered to depend on shape (defined by width to height ratio), rock mass strength, extraction ratio, in situ stresses and the gross structural features (i.e. joints, contacts, faults etc). Recent experience has shown that pillar stability is also controlled by the relative orientation of the orebody with respect to the in situ principal stress. In inclined orebodies, pillars are loaded in compression and shear, thus creating unsymmetrical stress distribution. Failure mechanisms of these pillars are little known. This paper investigates the failure mechanisms of pillars under shear loading. Two dimensional elastic numerical modeling was used to examine the behavior of pillars in different orebody inclinations relative to the major farfield stress orientation. First, the paper reviews pillar design approaches including the empirical pillar design chart and uses numerical modeling to investigate the effect of the major farfield stress orientation on pillar stability. It is concluded that the empirical pillar design chart be used with caution, and that for orebodies under shear loading mine planning and design should take this into consideration since such geometrical orebody/stress relations put mine structures at higher risk of instability.

Oct 1, 2010