Search Documents

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The industrial Internet of Things (IIoT)—a concept that combines sensor networks and control systems—has been employed in several industries to improve productivity and safety. NIOSH researchers are investigating IIoT applications to identify challenges of and potential solutions for transferability of IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40% of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system based on low-cost microcontroller Wi-Fi boards, to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine, and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communications and tracking infrastructure. INTRODUCTION The nation’s approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communications with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there currently exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT). IoT is the network of physical objects or ""things"" embedded with electronics, software, sensors, and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator, and/or other connected devices [1, 2]. It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: internet and things. The first one pushes towards a network-oriented vision, while the second tends to put the focus on generic objects. The traditional internet can be viewed as an internet of computers —i.e., “things” connected to the internet are computers only. IoT “extends” the internet by allowing other generic things that are commonly found in our daily life, such as refrigerators and cars, to be interconnected via the internet, and thus creates a bridge between the virtual word and the physical world."

Jan 1, 2017

By G K. Jorkenson

The SABREX Blast Modelling Program was developed joinlly by the companies of the ICI Explosives Group. of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.

Jan 1, 1989

By Thomas C. Atchison

The purpose of this Bureau of Mines investigation was to measure the amplitude and shape of the strain pulse and the size of the crushed zone produced in a granite by different explosives and to determine how these quantities are related to the detonation properties of the explosives. The reflection theory of rock breakage has shown that the amplitude and shape of the strain pulse incident at a free surface determine the fragmentation and volume of rock broken. Determination of the properties of an explosive that control the characteristics of the strain pulse produced in the rock will help in evaluating explosives for use in blasting. The investigation showed the different explosives produced a twofold variation in the amplitude of the strain pulse but little variation in the shape of the pulse. The explosives also produced a twofold variation in the volume of the crushed zone, but differences among the explosives were more accurately determined by strain-amplitude measurements than by crushed-zone measurements. The peak amplitude of the strain pulse and the volume of the crushed zone correlated with the calculated detonation pressure of the explosive.

Jan 1, 1959

By M. Javier

Mining, waste is growing problem both physical accumulation and increasing toxic uncertainties it presents in the long run. Its value ?zero? is strictly calculated by economy. This mining model begs the question: What is the value of waste & what does it represent to the mining industry? Waste is widely accepted as a ?by product? generated as a consequences of the mining process. The abundant waste accumulation affects society, as receptor, in many ways and the waste piles of materials has no use and no destiny. In reality, this waste is monument of imperfection of the extractive industries worldwide. Our planet is finite and has strict limitations, which mining has traditionally ignored. It is time to design a new system, in which clearly, waste design must be integrated in whole mining process; it has no room to postpone. This paper presents a concept in waste design by which toxic mining waste not only can be rendered inert but also act as nutrient to help balance the ecosystems. This concept calls for extractive industries to pursue EQUILIBRIUM with nature (Geomimic). Also, this concept offers countless gains and opportunities fro the industry and by converting liabilities into assets; mining engineers become the managers and stewards of nature. Also, waste design offers new solutions for proper and sustainable waste management of the mining industry.

Jan 1, 2011

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

By H. F. Dunlap, R. R. Hawthorne

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By R. R. Hawthorne, H. F. Dunlap

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By E Beltran, S Ngunz, F Orrante, F van Zyl, M Westcott

"The primary control objective of the project is to achieve milling optimisation by ensuring that the energy available for rock breakage is used as efficiently as possible. This is achieved by increasing the level of mill filing until a process constraint is reached. Stable operation against this limiting constraint is then maintained to ensure long-term optimised operation.Semi-autogenous grinding (SAG) mill control optimisation presents a number of challenges. SAG mills have multiple inputs that are used to control multiple outputs (MIMO process). Secondly, the SAG mill loading process is a ‘high inertia’ process that can be approximated as an integrating process. This means that it is open-loop unstable. The hybrid control strategy presented implements an advanced ‘load stabiliser’, which transforms this integrator process into a more manageable first order process, which can be steered stably against the constraints. This SGS hybrid Expert control strategy implemented on both SAG mills at the Porgera concentrator therefore consists of two integrated parts responsible for:stabilising the mill load to a targetdriving the mill load target to the maximum determined by the process constraints (eg maximum power draw) to maximise efficiency and throughput. A comparative study is done between the operation of the plant for a period of a month before and a month after the implementation of this strategy. The results indicated a significant improvement in the SAG mills’ stability and operation as well as a reduction of overload situations leading to a loss of throughput.Citation:Ngunz, S, van Zyl, F, Orrante, F, Beltran, E, Westcott, M and Wilson, S, 2016. Simplified Hybrid Semi-autogenous Grinding Mill Control - Explanation and Practical Results at the Porgera Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 313&ndash;320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By N. L. Piret

Primary and secondary copper smelting dusts are being generated in varying quantities with very dissimilar characteristics due to the different compositions of feed materials and the type of process utilized. After categorizing the multitude of dust types, the criteria for on-site and off-site recycling of smelter dust in terms of type and concentrations of the accompanying elements are established. Thereby, consideration is given to the important aspects of: ? optimization of copper recovery ? quality of copper product ? valorization of accompanying elements ? elimination and disposal of deleterious impurities ? minimization of impact on operation ? effects on operating costs ? environmental impact of dust treatment on overall process Existing commercial, emerging and proposed copper smelting dusts, pyrometallurgical as well as hydrometallurgical, treatment schemes are reviewed and evaluated technically, economically and environmentally in an attempt to streamline the vast number of proposed options. Thereby, the high selectivity achievable in hydrometallurgical dust processing due to it being complementary to the smelting process is expected to be given increased consideration.

Jan 1, 1995

By M. Grun, A. C. Marlowe, I. Littleford

SYNOPSIS A Wirth tunnel borer owned by Anglo American Corporation completed a 1150m long tunnel some years ago and was subsequently extensively modified by Technical Development Services. In 1982 this borer provided new and particularly interesting information In the field of hard rock boring. The abrasive quartzltes traversed proved to be a challenge to the cutter manufacturer and the project team. This paper examines the problems faced, the solutions found and the lessons learnt.

Jan 1, 1983

By Alan A. Campoli

OD March 20, 1989, a meeting was held at the U.S. Bureau of Mines Pittsburgh Research Center at the request of Senator Pete V. Domenici of New Mexico. The purpose of the meeting was to engender a technical relationship between the National Laboratories and the minerals industry. During the meeting, the Director of the Bureau of Mines, T S Ary, suggested that since the Bureau is the focal point for mining research in the United States, it would be appropriate for the agency to act as the liaison between the National Laboratories and the minerals industry. As the first step in this process, the author was selected to perform a 6-month investigation to better define the proper role of the Bureau in this area. As part of the investigation, the mining and mineral-related technology available at 21 major U.S. Department of Energy (DOE) Research Laboratories was reviewed. It was assumed that the broad range of scientific and technical areas covered DOE research would provide fertile ground for mining-related technologies. It was hoped that the applicability of DOE research to this liaison effort would be indicative of Federal laboratories in general.

Jan 1, 2011

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilise crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realise reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By E. A. Ziemba

The modified in-situ process is one of the methods being considered for extracting oil from oil shale. One of the questions to be answered for this approach is the environmental consequence of underground retort abandonment. This report outlines a study which addresses the question in terms of a grouting solution. It covers the development of a spent shale ash based grout which will fulfill the environmental requirements in terms of strength, stability, and impermeability. In addition, it will allow the reinjection of up to 50 percent of material mined and surface retorted as part of this process.

Jan 1, 1982