Search Documents

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011

By Raymond B. Ladoo

The uses for which ground talcs are suited closely depend upon their physical and chemical properties , but , in spite of this fact , little scientific investigation has been made in order to devise quick and accurate tests for the determination of these properties . The chemical properties of talc are inherent and may not be altered or modified except by selective mining or by chemical processes not practical in the present status of the industry . However , the determination of chemical properties is not so important , for most uses , as of physical properties , although sometimes certain chemical characteristics are perhaps unduly insisted upon by chemists in some industries . Physical properties are dependent both upon mineralogical characteristics and upon methods of grinding and sizing and may thus be partly changed or modified by changes in practice . There is so little known of the chemistry and physics of the various processes in which talc is used that the purchase and sale of talc is governed more by rule- of- thumb methods dependent upon individual opinion and often , prejudice , than by accurate , standard tests . This not only causes unwarranted price fluctuations , but injures both the producing and consuming industries by creating false ideas of the suitability of talc for various uses . It thus seems important that present tests be standardized and made uniform for the whole industry , and that new tests devised to fill the existing gaps .

Jul 1, 1920

Established as a Society February 26, 1957 John S Bell, President Wayne E Glenn, President-elect Basil P Kantzer, Past President R E Howard, Vice, President M B Penn, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Bldg Dallas 1, Texas

Jan 1, 1959

By L. H. Michaud

A mining company plans to extend its surface coal-mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accountings for the site shows an overall Neutralization Potential to Maximum Potential Acidity Ratio (NP:MPA) of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to be mined. If traditional dragline-mining methods are used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of acid mine drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. To prevent the formation of AMD, the company has proposed to mine the area using truck-shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, amine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil to achieve an overall net alkalinity in all spoil areas. Therefore, mining this site should not result in the formation of AMD.

Jan 1, 1996

By J. Drew

Oregon Resources Corporation (ORC), an industrial minerals mining company, is currently engaged in the development of a new process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be mined efficiently and economically, creating an additional domestic source for chromite, garnet, and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America. Metallurgical study of the placer material was grouped into four distinct samples based on marine terrace deposition, geological facies, and mineralogy. Because the metallurgical samples represented the extremes likely to be encountered in all future Oregon paleo-beach placer ores, the process design is highly dynamic and will successfully adjust to meet the production needs. Water availability at the mining area is seasonal and will not support a typical placer operation?s water requirement needs for heavy mineral concentration. For this reason, ORC has developed a plan to construct the ore processing facilities near Coos Bay, where a municipal source of water is available. Raw ore will be transported from the mining sites approximately twenty miles one way to the processing facility with return loads hauling tailings back to the active pit. The need to haul dry tailings, return dry material to the pit for reclamation, and limit the amount of water being purchased from the municipality has driven the design of a unique water reclamation system. BACKGROUND Location and Access Economic concentrations of ?black sand? or heavy mineral (minerals with specific gravity greater than 2.85) have been recognized and studied in marine placers from Coos Bay to the mouth of the Rogue River, a distance of approximately 75 miles along the southern Oregon coast (Hornor, 1918; Griggs, 1945)(Figure 1). ORC will begin mining existing reserves approximately 20 miles south of Coos Bay in a region known locally as Seven Devils. Ore will be trucked north to the processing site near Coos Bay via use of existing county and state roads, including U.S. 101. The available facilities at the processing site include highway, rail, municipal water and electricity, natural gas, and a deep water port. At the time of this writing, the rail line had been abandoned, but was being pursued by the International Port of Coos Bay. It is anticipated that this will be serviceable at some time in the future. History The southern Oregon marine placers have garnered the interests of miners since 1852, when present day beaches were exploited for gold. The beach deposits were small and irregular in nature and were easily washed away by the major storms the coast endures during the winter months (Hornor, 1918). [ ] In the 1920?s, deposits at the beach were followed upstream to their paleo-beach terrace origins (Pardee, 1934). These terrace placers were mined, but with little success, as the cost of mining and processing was greater than at the present day beach deposits. The greatest effort to understand and delineate the paleo-beach terrace placers came during World War II. As the need for a domestic source of steel hardening chromite was evident, the heavy mineral bearing placers of southwestern Oregon provided just that. The U.S. Geological Survey, under guidance from the Oregon Department of Geology and Mineral Industries, began exploration drilling of the paleo-beach terraces in 1940 (Griggs, 1945). This work was part of the investigation of strategic mineral deposits and would ultimately supply much needed chromite for the war efforts. The first mining efforts began in 1943 by the Humphreys Gold Corporation and the Krome Corporation (Griggs, 1945). Black sand

Jan 1, 2009

JAMES A. BARR Consulting Engineer Mt. Pleasant; Tennessee Washington, D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia LENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.

Jan 1, 1952

[JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Montieello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By D Craw

At Reefton, mesothermal gold deposits occur in the Ordovician Greenland Group basement and bituminous coal deposits occur in overlying Eocene Brunner Coal Measures. These different resource types occur in close proximity to one another in the same topography, vegetation and climate. Both types of resources have been mined for many years and as a result historic mining areas discharge water with chemistry reflecting the mineralogy of the deposits. Coal measures release natural acid rock drainage throughout the region due to oxidation of pyrite in coal and associated sediments. Levels of acidity are increased in mining areas, and pH near three is common. Gold mines contain pyrite, arsenopyrite and stibnite. Discharge waters from these sites have pH near seven because of the high acid neutralising capacity of the basement rocks. Both coal and gold mining sites have iron oxyhydroxide precipitates in drainage waters. These precipitates are more abundant at gold mining sites, and one deposit is up to 5 m thick. Iron oxyhydroxide at coal mine sites contain Zn (up to 89 ppm), Ni (up to 10 ppm), As (up to 163 ppm), Cr (up to 23 ppm), Pb (up to 16), and Cu (up to 11 ppm). Jarosite group minerals have been identified in the coalmine iron oxyhydroxide, although most of the material is amorphous. Gold mine iron oxyhydroxide contains Zn (up to 353 ppm), Ni (up to 592 ppm), Cr (up to 17 ppm), Cu (up to 72 ppm), Pb (up to 29 ppm), Sb (up to 230 ppm), and this material is particularly high in As (up to 20 wt per cent). Most of the material is amorphous but distinctive zones (mm scale) are As rich (up to 30 wt per cent As oxide). Pharmacosiderite, K2Fe4(As04)3 (OH)5.6.3H20, is a secondary mineral in one deposit. These iron oxyhydroxide deposits are useful indicators for the metals mobilised into the environment by oxidation in the historic workings.

Jan 1, 2003

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

JAMES A. BARR Consulting Engineer Mt. Pleasant. Tennessee Washington. D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Callf.

Jan 1, 1952

By Randal Martin

Recently, questions regarding the influence of atmospheric temperature and humidity levels on airblast levels have arisen at a number of blast sites. Humidity is alleged to have contributed to high levels of disturbance within communities surrounding blasting. In some cases, local regulatory agencies considered adopting guidelines to specify humidity and temperature ranges under which blasting cannot take place. However, it is normal blasting industry practice not to consider humidity or temperature effects, in the absence of inversions, on airblast levels. When blasting is conducted in the vicinity of residential structures, the influence of weather on the propagation and attenuation of airborne noise from the blasting site is always a concern. Sound naturally attenuates in air with distance from the source. A part of this attenuation is attributed to divergence at the airblast wave front, while the remainder of the attenuation is an accumulation of various factors that include temperature and barometric pressure, absorption in air due precipitation and vegetation, wind and temperature gradients, atmospheric turbulence and topography (Beranek, 1971). Wind speed and wind direction, as well as vertical and horizontal temperature gradients can cause airblasts to focus in local regions surrounding blasting operations and may result in air pressures greater than expected. In fact, wind and temperature inversions can actually increase sound levels with distance from the blast site. Close to the blast site, the effects of inversions may be negligible but may exceed 10 dB at 800 m or greater (Davis and Cornwell, 1991).

Jan 1, 2001

By P Paredes, T Leaño, D Gajardo, C Tramón, S Peñaloza

The definition of an ore handling system and its consequent layout design is of crucial importance in cave mining projects. It not only represents the main driver in the production capacity and reliability of the mining system, it is also a fundamental variable in the footprint’s development time and cost.In recent decades, load-haul-dump (LHD) tramming distance optimisation through the allocation of several orepasses inside the footprint has been the most common practice in ore handling system layout definition at Codelco’s operations. Today, the improvement of existing technology, such as higher-capacity LHDs and jaw-gyratory crushers, and intensive preconditioning techniques to improve fragmentation allow the conceptualisation of simple and highly productive ore handling system layouts for wide caving areas that avoid the complexity and high cost of developing numerous orepasses inside the footprint.The initial macroblocks of the Chuquicamata underground mine project (PMCHS) consider an ore handling system layout in which LHDs dump into orepasses located inside the footprint area. The ore is then transferred into crusher chambers located below the production level, where it is crushed by jaw crushers and then conveyed to surface. In an effort to reduce development time and costs, a new ore handling system layout for the PMCHS experimental macroblocks was engineered using improved technologies and techniques in a simpler mining system. This paper compares the new ore handling system layout for the project’s experimental macroblocks with the traditional LHD-orepass layout in terms of production capacity, reliability, development time and cost.CITATION:Paredes, P, Gajardo, D, Leaño, T, Peñaloza, S and Tramón, C, 2016. Simplifying the ore handling system through the use of current technology at Chuquicamata underground mine project, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

In 1976 the Pitjantjatjara Council was established under the Associations Incorporation Act 1985 (SA), for the initial purpose of organising and bringing together three similar Indigenous groups. These members of the Pitjantjatjara Council of Central Australia were demanding land rights and to legally protect their traditional lands. The Land Rights movement was more focused on the South Australian Government that became more receptive to the general notion that Aboriginal freehold land could be attainable.For almost five years, Pitjantjatjara CouncilÆs intense negotiations took place with the Dunstan and Tonkin Governments culminating in the final passage of legislation by 1981. A bi-partisan approach by Government and opposition applauded by all South Australians for its mature and socially responsible actions, in line with the Aboriginal Land Rights (Northern Territory) Act 1976 (Cth). Despite the similarities between South Australian and the Northern Territory Land Rights legislation, there still remains one obvious distinction. In the Northern Territory case, its legislation established æLand CouncilsÆ as statutory authorities that are responsible for the management and use of designated Aboriginal lands. On the other hand, South Australian legislation fails to include any reference to æLand CouncilsÆ as defined in the Northern Territory Act. The intention of establishing such æLand CouncilsÆ in the Northern Territory was, and is to provide legal, anthropological and other expect advisers that respond to the wishes and opinions of Traditional Aboriginal Owners. Negotiations between mining companies and Land Councils, will, after the granting of mining leases, monies are then transferred to those Councils being a percentage of royalty entitlements. While the Pitjantjatjara Land Rights Act 1981 (SA) (Act) does provide royalty arrangements to Anangu Pitjantjatjara (AP), a body corporate pursuant to the Act as a Landholding Body (and not as a æLand CouncilÆ), it does not provide any royalty payments for the legal and anthropological services by the Pitjantjatjara Council for providing essentially similar services as the Northern Territory Land Councils. The limited services by AP do provide complimentary services from other organisations û including the Pitjantjatjara Council. There are approximately 4000 Anangu members who reside on AP Lands and more than 1000 other Anangu members live near AP Lands in Western Australia and the Northern Territory. These people are defined as APÆs æTraditional OwnersÆ by virtue of their affiliation to portions of AP Lands. As a result, the depth and understanding of spiritual beliefs and customs are strongly present as it relates to the whole of the Lands. Most of these members reside at permanent communities that spread unevenly about the northern and south-western parts of AP Lands. In addition, there are numerous æHomelandsÆ where families and extended families have establish homes, with electricity and water supplies on those Traditional Lands (see Appendix 1 and 2 of this paper depicting the map showing AP Lands and also showing stunning photographs taken during late last year). All roads and airstrips are unsealed between communities and Homelands and the essential services to all communities are limited and costly to provide, and require continuous upgrading. Capital expenditure on infrastructure is sorely needed and alarming levels of unemployment is of serious concern. Tjilpi (older) Anangu members have continually discuss the urgency to provide employment and education for the future of their children and grandchildren while balancing the needs of maintaining cultural and spiritual considerations. It is thus a growing realisation by many Traditional Owners that long-term benefits occur as a result of exploration and production of oil or minerals. There are promising results from Primary Industry and Resources of South AustraliaÆs (PIRSA) Aero-magnetic Surveys on the Musgrave and Mann Ranges and soon to be completed surveys of the remaining southern half of AP Lands (see Appendix 3). PIRSA and mining companies û such as Rio Tinto Exploration Pty Ltd and Delta Gold NL û have been more conscious of the necessity for improving the dissemination of information to Traditional Owners and to AP members. With recent findings of large nickel deposits just over the border in Western Australia, there is a strong indication that discoveries may occur on AP Lands as similar geological information is present on the east Musgrave Block. Consequently there are concerted efforts by the legal and anthropological services of the Pitjantjatjara Council to arrange Workshops and Summit meeting to give extra information û particularly information concerning the true effect of large-scale mining operations û to members to properly consider these proposals. Pitjantjatjara Council will play a major role in any decisions effecting Traditional Owners and AP, and will ensure orderly and professional services when dealing with legal, cultural and sensitive matters. This paper addresses the historical and current relationship between Pitjantjatjara Council and AP, with an emphasis on mining operations on AP Lands. It argues that future economic and social development on AP Lands hinge predominantly on the legal recognition of the Pitjantjatjara Council for its ongoing role, responsibilities and protection afforded to AP and its Traditional Owners.

Jan 1, 2002

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By S. Zekovic

"The paper gives an overview of the economics condition and strategic business challanges of the mining&metallurgy sector and their possible impact on the future development of the Bor basin of copper in Serbian part of Danube Region. Economics and strategic challanges in the mining& metallurgy complex are emphasized by world economic and financial crisis. An analysis of strategic challanges is undertaken by application of a comprehensive development framework approach. Paper indicates that an economics and evaluation of possible impacts of constraints and challenges for the development of Bor basin shows that it must be included in corporative decision, local and regional plans.INTRODUCTIONRisks are characteristic of every strategic development and business decision-making, so their successful management should be a part of the development strategy of the corporation, especially longterm. Due to the growing uncertainty in the general socio-economic environment, “risk management”, risk insurance, risk control, risk culture, risk optimization are frequently talked about. Among the key risks at a corporate level are the financial risks and risks of the regulative framework, especially in the field of environment and land use. In both cases, it is a question of external risks, which the companies need to relativize and successfully manage. Some companies pay more attention to production risks and search for better solutions in that domain which is not enough (Ernst&Young, 2008). Strategic business risks appear mostly on the macro-economic level, from where they should be” transferred” onto the level of sector economics and action level in corporations. Risk management include transferring the risk to other parts, avoiding the risk, preventing hazard, reducing the negative effect or probability of the risk, accepting some or all of the consequences of a particular risk.The research has included perspective and the general market trend and market positioning of the production and copper processing complex in the world; the impact of the requirements and strategic goals of the EU Directive and Kyoto Protocol on the institutional and other adjustments important for business in this sector; the impact assessment of the regulations important for business in the mining and metals sector, and case study of economics and challenges for the development of mining and metallurgy sector in the Bor basin of copper in Serbian part of Danube region. The analysis has included the identification and assessment of the global challenges on the future development of the copper complex in the miningsmelting basin Bor. Presented results in the paper are part of the research project “Sustainable spatial development of the Danube area in Serbia"" (No. 036036), financed by Ministry of Education and science of Republic Serbia."

Jan 1, 2012

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the 'wet zone' with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013