Search Documents

By Avery H. Reed

RECORD production of crude petroleum, lime, crushed marble, and talc highlighted the mineral industry of Alabama in 1963. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 86 percent of the total value of production, compared with 82 percent in 1962. The iron-ore industry continued to decline; in 1959 the value of iron ore produced was 12 percent of the total State production value; in 1960, 11 percent; in 1961, 10 percent; in 1962t 8 percent; and in 1963, 5 percent.

Jan 1, 1964

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators (VPHGMS) possess the advantages of high efficiency and high reliability in beneficiating weakly magnetic minerals. In recent years, models SLon-2250, SLon-2500, SLon-3000 and SLon-4000 have been developed. This paper gives several examples of their applications in oxidised iron ore and ilmenite processing flow sheets to improve iron and ilmenite recoveries.CITATION:Dahe, X, 2017. Recent development and application of SLon vertical ring and pulsating high gradient magnetic separators in the iron ore and ilmenite processing industries, in Proceedings Iron Ore 2017, pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

Paper written on project work carried out in partial fulfilment of B.Sc. Eng. (Extractive Metallurgy)degree The concepts behind support vector machines are very interesting both in theory and in practice, as they are based on a universal constructive learning procedure derived from the statistical learning theory developed by Vapnik. In this paper, their application to time series modelling is considered by means of simulated data from an autocatalytic reactor. In particular, reconstruction methods from non-linear dynamics are used to define a state space model for the process. Multivariate embedding techniques are compared to scalar embedding with respect to modelling. Keywords: System identification, Support vector machines, Multilayer perceptrons, Non-linear dynamics

Jan 1, 2003

By L R. Marshall, M J. Rubenach, T G. Blenkinsop, J S. Cleverley

The source and transport regions of fluidised (transported) breccias outcrop in the Cloncurry Fe-oxide-Cu-Au district, providing insights into the origins of other fluidised magmatic-hydrothermal breccias such as kimberlites. Discordant dikes and pipes with rounded clasts of metasedimentary calc-silicate rocks and minor felsic and mafic intrusions extend several kilometres upwards and outwards from the contact aureole of the 1530 Ma Williams Batholith into overlying schists and amphibolites. The brecciation initiated at depths >10 km and may have resulted in surface breaching. We used analytical equations for particle transport to estimate clast velocities (eÆ 20 ms-1), approaching volcanic ejecta rates (up to 80 ms-1). The wide range of CO2 fluid inclusion densities (up to 150 MPa), the localisation of the base of the breccias in contact aureoles, and the scale and discordancy of the bodies suggests the breccia transport process was triggered by an abrupt release of overpressured fluid. At these depths, such extreme behaviour may have been achieved by release of dissolved fluids from crystallising magma, in combination with a strongly fractured and fluid-laden source, sitting under a strong, low permeability barrier, and such parameters may be analogous to the asthenosphere/lithosphere boundary in the case of kimberlite initiation. The relationship of these breccias to the Ernest Henry iron-oxide-Cu-Au deposit suggests they may have been either fertile or æfailedÆ orebody feeders.

Jan 1, 2005

By V. A. Melezhik, P. K. Skufin, L. P. Nilsson

these factors into account. Theoretical and

Aug 1, 1994

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

Established as a Society February 26, 1957 OFFICERS AND COMMITTEES Wayne E Glenn, President Earl M Kipp, President-elect John S Bell, Past President R A Morse, Vice-President W D Owsley, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 6300 North Central Expressway Dallas 6, Texas

Jan 1, 1960

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

Devitrification of a glassy volcanic ash equivalent to an alkaline trachyte in composition has resulted in the formation of an interstratified illite-montmorillonite with an 1:1\1 content of 1:4 as the principal clay mineral.A high concentration of potassium ions and a deficiency of magnesium ions favoured the formation of the potassium-bentonite.A poorly ordered mica mineral, equivalent to illite, was produced by weathering of potassic feldspar. Subsequent degradation of the illite through the loss of potassium was responsible for the formation of several interstratified minerals with very approximate 1:1\1 contents of 4: I as minor components.Other authigenic minerals present in small amounts were u-cristobalite, sepiolite, and the zeolite clinopitolite.The non-swelling character of the potassium-bentonite makes it economically unattractive...

Jan 1, 1967

By J. N. Van der Merwe

The research described in the paper was aimed at providing standardized information of cases of failed and intact coal pillars in the form of databases to researchers. It also offered the opportunity to take stock of the pillar stability situation in coalmining and to review the impact of the application of the safety factor formula for pillar design. It was found that the physical parameters of coalmining have not changed substantially over the last four decades. However, changes in the controllable parameters like pillar width, pillar width-to-height ratio and percentage extraction have all moved toward the more conservative side. Scrutiny of the database indicates that of all the failures recorded, only 23 occurred in panels that were mined after 1969, when one can assume that the safety factor formula was fully applied. If the pre-1969 practices had been continued, at least 144 collapses would have been expected. There has thus been a substantial reduction of pillar collapse cases, justifying the cost paid for the formula, which has shown to be in the region of 600 million tons of coal. It is evident that that are distinct differences in the natures of the failures among different coalfields. This justifies the attempts to derive seam or coal field specific strength formulae and is a topic that should be pursued.

Jan 1, 2006

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By Stephen L. Chryssoulis, Stamen Dimov

"Preg-robbing has been known for many years, where increased losses are suffered because dissolved gold is removed from solution by adsorption onto carbonaceous matter. In direct cyanidation circuits it is reasonable to conclude that the preg-robbed gold is either in a gold cyanide [Au(CN) - 2, AuCN] or metallic [Au°] form. However, in circuits with a pre-oxidation step possibilities increase and multiply even further because of water recycle streams containing apparent and not-so-apparent gold ligands. It is in these circuits where speciation of sorbed gold, i.e. the identification of the gold compound, is useful. The importance arises from the fact that proper identification of the sorbed gold species can be used to determine how, when, where and why gold was removed from solution, thereby identifying the exact cause of the problem and providing clues as to how it may be rectified.INTRODUCTIONTo the best of our knowledge, this is the first attempt ever to speciate gold preg-robbed by carbonaceous matter using a surface sensitive microbeam technique. This approach enables the direct determination of gold species sorbed on carbonaceous particulates, opening an entirely new field in the understanding of the chemistry of gold sorption on carbon. The reasoning behind this effort was to add to the current knowledge of the detrimental effect chloride ions have on gold recovery by the pressure oxidation and in particular why in the ensuing CIL step, gold is not being desorbed from the surface of the carbonaceous particles (Table 1)."

Jan 1, 2004

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco's Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006