Search Documents

The Hishikari gold deposit, discovered by the Metal Mining Agency of Japan, has become a giant class epithermal gold deposit with the highest grade of gold yet recorded in the world through detailed exploration and development by the Sumitomo Metal Mining Co Ltd. The exploration strategy involved a regional approach combining geological and gravity surveys over a 900 km2 area which had historically produced over 120 t of gold. These surveys were carried out to grasp the common geologic features of epithermal gold deposits in the survey area. A genetic model for epithermal gold deposits in the area under regional survey was also considered based on detailed research of the Kushikino epithermal gold deposit which was in operation at that time. This model was applied to the targeted areas, and important relationships between mineralisation, host lithology, intensive propylitic alteration and gravity highs became apparent. The Hishikari block was selected in this way and bonanza gold was discovered during drilling. Since the development of the Hishikari mine, information useful for further exploration for the same type of deposit has been accumulated.

Jan 1, 1995

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By D. Symonds, A. J. Richins, M. G. Nelson

Mining activities at Kennecott and Park City are similar in that both districts began operation in the last half of the 18th century, and both operated on a large scale for many years. However, they are different for two important reasons. First, the mines in the Park City district were always underground. The city of Park City was above many of those mine workings. It remained in place after mining activity stopped, and as the town became an up-scale ski resort, property values increased and the tailings dumps became desirable building sites. In contrast, Kennecott eventually became an open pit mine, and the growing pit effectively consumed many of the small towns that had grown up around the underground workings. Even towns on the periphery of the open pit were razed to allow for the disposal of mine overburden. Second, almost all mining activity stopped in Park City in the early 1970s, just as the first rigorous environmental legislation in the United States was enacted. (The Ontario mine operated sporadically until 1982.) Many mine structures, waste dumps, tailings ponds and piles, and tunnels were simply abandoned as the mining companies ceased business or were bought out. Kennecott, on the other hand, has been in continuous operation for more than 120 years, so a closure plan hasn’t been finalized. Nonetheless, environmental and social problems have arisen, and the company has had to address them.

Mar 2, 2022

Circulating Air Classification of Manufactured Sand Due to environmental concerns, the supply and use of natural gravel has been limited by the Swedish government. The Swedish concrete industry is therefore examining manufactured sand as an alternative that has equal or better product quality, and which the Swedish quarry industry already has the ability to deliver. However, in order to comply with the specifications set by the concrete industry, a better means of classification is needed, as the proportion of fine particles (filler) smaller than 63 - 125 ¦m in size must be reduced. One classification technology that meets the requirements may be air classification. This paper examines the process of circulating air classification, which is not yet commonly used in the Swedish quarry industry; suggesting that a better understanding of the process is needed. The circulating air classifier in this study has two internal machine parameters that can affect the separation point; namely, the speeds of the circulating fan and the separator fan. We study their effect on the separation point as well as the interaction between these parameters. Full-scale parameter tests are also conducted, in which size distribution is measured before and after the circulating air classification. This study shows how the different parameters affect the separation point and that it is possible to produce manufactured sand according to specifications. Computational fluid dynamics (CFD, Fluent) is used to study the internal flow of the air circulating within the classifier. A single-phase study of the flow field is conducted to support and explain the findings from the full-scale tests.

Sep 13, 2010

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By Neil H. Brown

Outline ? Cameco - Cigar Lake ? Cigar Lake Mine Development ? MDS #1 ? MDS #1 Improvements ? MDS #2 ? MDS #2 Improvements Pending ? Acknowledgements Mine Development System ? Mining methods tested and developed over the years ? Construction began officially in 2005 ? Water inflow events in 2006 and 2008 ? Successful dewatering and re-entry in 2010 ? Remediation continues ? Production target is mid-2013

Oct 1, 2010

This paper examines the issues involved in the technical audit and valuation of exploration prospects. Certain methodologies are more appropriate to use depending upon whether the mineral property valuation is of an exploration area, a project under development, or an operating mine. Valuation approaches that are reviewed include the Multiple of Exploration Expenditure, Joint Venture Terms, Rules of Thumb, and particularly the Kilburn Rating Method. The DCF/NPV Financial Simulation Method, even modified by the use of Expected Values, is not considered appropriate for valuing exploration prospects. The choice of the most appropriate methodology and its successful application depends primarily upon the amount of reliable input data available and, more importantly, the experience and judgement of the valuer. It must be remembered that all valuations are time and circumstance specific and will be generally subject to revision as more data becomes available.

Jan 1, 1993

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.   There is a great need to improve science, natural science, education at all levels. All people must know how our planet works and that fluctuations, some inevitable, some controllable, are inevitable and that we must prepare for them. And it is clear that protecting the environment, eliminating pollution, preserving bio diversity is good economics. Ecology Economy cannot be separated.  

Jan 1, 1995

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By E. D. Gardner

From the standpoint of tonnage and dollar value copper is the most important nonferrous metal mined in North America. The opening of copper mines has had an important bearing on the development and settlement of many sections of the continent. The prosperity of many of the mining States or provinces depends directly upon the copper-mining industry. Normally, about 35,000 men are employed in the copper mines, mills, and smelters of the United States. The United States is the most important producer of copper among the nations; more copper is mined in North America than in any other continent, and for many years the United States alone produced about half of the copper of the world. During the last 10 years increasing production in South America and Africa has reduced the relative importance of North America and the United States.

Jan 1, 1938

By Unknown

More than 60 years ago Lakota (Sioux) Chief Henry Standing Bear asked Korczak Ziolkowski to create a monument of Crazy Horse in the sacred Black Hills. Today, you can see Standing Bear’s dream has grown into enormous reality. Crazy Horse Memorial, mankind’s largest mountain carving in progress, is being carved in the round and when completed will be 641 feet long and 563 feet high. Crazy Horse is only 17 miles from Mount Rushmore National Memorial, giving South Dakota unique boasting rights for having two extraordinary mountain carvings in such close proximity

Jan 1, 2009

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

Map

Jan 1, 1941

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

By W. Hrynewich

"The Central Canada Potash facility, a division of Noranda Metal Industries Limited, is located 3 kilometres south of the junction of Highways 16 and 2, about 75 kilometres south-east of Saskatoon, Saskatchewan. The site occupies 26~ hectares of land and includes well-equipped machine and electrical _shops, a 325,000-tonne muriate storage and reclaim warehouse, a stores warehouse, processing plant (mill), two mine shafts (one for production, the other for servicing and personnel transport), as well as a two track product loading complex. Access to the site is by road and railway (CN and CP Rail). Suppliers of operating and maintenance use both means of transportation, whereas muriate shipments are entirely by railway.Currently five continuous mining machines - one a Goodman 526 borer and four Marietta 911-A units produce some 10,500 tonnes of ore per operating day. A smaller Voest-Alpine Af.1-100 boom type miner is used for floor cutting which was previously done by a production unit. In order to maintain safe, competent ground conditions only 35 percent of the total ore is extracted. At this rate mine reserves are deemed adequate for about 100 years. The plant has operated since August 1969 and has a current practical annual capacity of 1,270,000 tonnes of muriate. As of June 30, 1981, some 11.9 million tonnes of muriate had been produced from 31.4 million tonnes of ore. Of the total muriate, 6.1 million tonnes was granular, 4.8 million was coarse, and 1.0 million was standard. No standard product has been made since August 1978."

Jan 1, 1982

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008

By H Peiming, W Sakurai, Y Matsuhisa, H Shimazaki, Y Fukahori

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skarn Pb-Zn deposits in the Kamioka mining district, centralJapan, where the wall rocks consist of heterogeneous rock units. The results (d18OSMOW of -1.1 to +17.3ë and d13CPDB of -5.0 to +4.8ë for limestones, and d18OSMOW of -0.8 to +12.5ë for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (18O and 13C) toward the centre of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralisation. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to-rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralisation had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360 m.

Jan 1, 1995