Search Documents

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By R L. Brathwaite

The mesothermal quartz-scheelite lodes of the Wakamarina valley are one of twelve known mined or prospected gold-bearing areas in the Marlborough Schist. Recorded production was 556 kg gold, a little silver, and c. 390 t scheelite. 134 m of the 1800 m long Golden Bar reef are accessible in the No 2 level of the Golden Bar mine. The reef is a typical multi-banded mesothermal vein, mostly c. 1.75 m wide, enclosing narrow horses of schist country rock. Scheelite is sparsely distributed, and is more common in small veinlets in the hanging wall schist. The country rocks are textural zone I-1m schists of prehnite-pumpellyite to pumpellyite-actinolite metamorphic facies. Their geochemistry suggests they are part of the Caples Terrane, and of calc-alkaline volcanogenic arc origin. The associated Wakamarina Quartzite is strongly recumbent folded, and of the same metamorphic grade, with abundant pumpellyite, stilpnomelane, and garnet, presumably spessartine. Although it has geochemical signatures of a deep sea sediment, it is depleted in Cr and Cu, and greatly enhanced in K and Ti, when compared with a standard chert. It also has trace element characteristics of a calc-alkaline arc-related sediment. However, associated greenschist has MORB-like incompatible element chemistry. The Golden Bar reef lies within a steeply dipping, normal to transtensional dip-slip fault adjacent to a shallow-dipping mylonite shear zone, which, at least on the footwall side, is 040 m wide. The shear foliation has been severely dragged down to nearly parallel the Golden Bar reef within 1 m of the quartz lode. Preliminary structural analysis suggests that the shear zone is extensional. X-ray diffraction analyses of the wall rocks show a progressive depletion of amphibole, stilpnomelane, and pumpellyite towards the reef, and enhanced illite/muscovite and Kfeldspar adjacent to the lode, along with possible graphitic carbon within 10m. Two zones of intense quartz veining occur, one adjacent to the hanging wall for 12 m and one from 40 m outwards. Quartz vein systems in the country rock are complex and span from pre-schistosity to post-mylonite. They include multiple generations of quartz, actinolite, stilpnomelane, pumpellyite, albite, adularia, chlorites, illite/muscovite, calcite, and scheelite. Metal analyses across the Golden Bar reef showed gold values of 0.13.1 ppm, and low tungsten values, consistent with the observed sporadic scheelite occurrences. As and Sb are at background levels, but enhanced Cr (150 - 430 ppm) relative to the schists (30 - 41 ppm) suggests that the source hydrothermal fluids passed through and leached mafic to ultramafic rocks.

Jan 1, 1994

By John H. Soulé

This paper describes the location and general features of the ?Red Bed? or sandstone copper deposits in southeastern Colorado and New Mexico. Most of the areas containing this type of deposit were visited, and many deposits were examined. Some deposits were not visited because of lack of information as to their location. In the large area covered a great variety of climatic, geographic, and topographic conditions exists. Some of the deposits are in arid areas, whereas others are in heavily forested regions. Altitudes range from 3,400 to 9,200 feet, and the terrain varies from flat plains to rugged mountains. Transportation is a difficult problem in most of the districts, involving long truck hauls to a railroad and long rail hauls to a smelter.

Jan 1, 1956

By F. C. Langenberg, J. Chipman

Jan 1, 1959

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By M. A. Trevits, M. R. Thibou, A. Ozment, A. C. Smith, J. B. Walsh

The Excel No. 3 Mine is a room-and-pillar mining operation owned by MC Mining, LLC, a subsidiary of Alliance Resource Partners, LP, which produces coal from the Pond Creek Coalbed in Pike County, Kentucky. Late on December 25, 2004, a fire was discovered near the bottom of the slope and, after an unsuccessful attempt to fight the fire underground, it was decided to address the fire remotely from the surface. The mine operator developed a plan to fight the fire that called for the installation of temporary seals at the slope and mine shafts to eliminate the inflow of oxygen. In addition, the plan called for drilling and completion of vertical boreholes into select areas of the mine workings to monitor the mine atmosphere and inject nitrogen gas and gas-enhanced foam. Over the next 9 days, nitrogen gas was injected almost continuously and gas-enhanced foam was injected periodically as deemed necessary. On January 7, 2005 it was determined that the fire was successfully suppressed. This paper presents a discussion of the fire-fighting approach and an analysis of the results of the application of gas-enhanced foam technology.

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981

By G. E. Vaninetti

During its modem era, the southern Powder River Basin (PRB) in Wyoming has grown from meager origins in the early 1970s to become one of the most important coal-producing regions in the United States. In 1993, production and sales of southern Powder River Basin coal exceeded 190 Mt (209 million st), or about 20% of the US coal industry. Despite the remote location of the PRB relative to its potential markets, most coal industry observers anticipate continued strong growth to meet utility compliance plans for Phases I and II of the Clean Air Act Amendments (CAAA). This article is an overview of supply and demand issues concerning the marketing of southern PRB coal. It reviews the events leading up to the recent run on spot coal and offers a forecast of demand and prices.

Jan 1, 1994

By William H. Schiffbauer

The Bureau of Mines is conducting research that is aimed at making the mining industry more efficient in term of both productivity and the health and safety of the worker. As part of this research the Bureau of Mines has integrated a testbed composed of computer and related peripheral hardware to form an intelligent base for performing autonomous mining machine experiments. Although this particular application was con- figured for use on a Joy 16 CM mining machine, its generic structure facilitates its attachment to a variety of mining machine types. The multitasking multiuser computer can be set up for other applications by changing a bubble memory cartridge. The Joy 16 CM implementation includes 96 digital input-output (1-0) ports, 32 analog inputs, 8 analog outputs, 2 serial data channels, and 1 printer port. Operation of the machine can be performed either through a local terminal or remotely through a modem hookup. This report describes a testbed for autonomous mining machine experiments (TAMME)--its hardware, software, and complete system integration--so that it can be used as a foundation for other applications.

Jan 1, 1988

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10- to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 1993

By R. Emmett Hughlett

The Bureau of Mines has developed a statistical approach to the laboratory evaluation of response bias and precision in gas detectors. The techniques described employ a computerized analysis and a new method of data presentation called composite graphing. The underlying theory, its practical application to the data, and the experimental equipment and procedure are described.

Jan 1, 1982

The widely accepted concept of mineral resources are that they are finite - mining therefore being intrinsically unsustainable. Yet the modern global mining industry continues to grow production at strong rates - how can this be? In reality, mining is a complex industry, starting with exploration, development, operations and then rehabilitation and closure. A recent major study of Australia has shown that for most mineral commodities, exploration continues to find new deposits, or expand resources at existing mines. In parallel, however, there are a number of key 'mega-trends' which are growing in their importance - declining ore grades (or quality), increasing tailings and waste rock volumes, the need for deeper mining, more refractory ore types, increasing energy inputs and higher unit energy costs, increasing pollution issues and, of course, not to forget greenhouse gas emissions issues. This paper will present a detailed case study of the ultimate sustainability of the Australian mining industry - showing long term historical data sets on ore grades, waste volumes and economic resources and placing these trends in light of major twenty-first century issues such as energy supplies (especially Peak Oil), climate change and existing and emerging land use conflicts (eg agriculture versus mining). Australia is a critical case study in the sustainability of mining, as it is a major global exporter of numerous commodities, and this is expected to continue to underpin the ongoing industrialisation of countries such as China and India. The ultimate question begs - can Australia actually meet this fundamental challenge, or will our resources run out, or will we be constrained by environmental issues such as climate change, land use or perhaps water? Rather than a mere optimist's or pessimist's view, this paper will present a range of hard data which underpins the debate about the sustainability of mining this century: ultimately, we cannot assume that the patterns of past mining will continue to work in the future. The sustainability of mining continues to hang in a precarious balance.

Jun 1, 2010