Search Documents

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By W. N. Marchant

[The citrate process for flue gas desulfurization (FGD) is a product of continuing research by the U.S. Bureau of Mines to meet the goal of minimizing the objectionable effects of minerals industry operations upon the environment. The reduction of SO2, in solution by H2S to produce elemental sulfur by the citrate process is extremely complex and results in solutions that contain at least nine different sulfur species. Process solution analysis is essential to a clear understanding of process chemistry and its safe, efficient operation. The various, chemical species, the approximate ranges of their concentrations in citrate process solutions, and the analytical methods evolved to determine them are hydrogen sulfide (~0M to 0.06M) by specific ion electrode, polysulfides (unknown) by ultraviolet (UV) spectrophotometry, elemental sulfur (~0M to -0.001M dissolved, ~0M to ~0.1M suspended) by W spectrophotometry, thiosulfatc (~0M to ~0.25M) by iodometry or high performance liquid chromatography (HPLC), polythionates (~0M to ~0.01M) by thin layer chrornatogrphy (TLC), dithionite (searched for but~ not detected in process solutions) by polarography or TLC, bisulfite (~0M to 0.2M) by iodometry, sulfate (~0M to 1M) by a Bureau-developed gravimetric procedure, citric acid (-GM to 0.5M) by titration or visible colorimetry, glycolic acid (~0M to 1N) by HPLC, sodium (~1.5M) by flame photo¬metry, and chloride by argentometric titration.]

Jan 1, 1980

By Bruce Vandenberg

Two tests were set up as part of the course given by Blasting Analysis International. Both tests were performed using the prototype Velocity of Detonation Recorder (VODR). The prototype has several limitations, which have been rectified for the production units.

Jan 1, 1990

By Howard Eavenson

THE low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent. The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper.

Jan 1, 1931

By B Cope, Y Churi

Roxgold was a small exploration company when it discovered the Zone 55 orebody at the Yaramoko project in Burkina Faso in 2010. Since this time, it has actively progressed the project with the completion of a preliminary economic assessment in 2013, a feasibility study in early 2014 and obtained full permitting for construction in January 2015. With no other underground gold mine in Burkina Faso, developing a modern and productive modern gold mine in West Africa was considered a significant challenge as Roxgold moved from explorer to producer.To facilitate this development, Roxgold engaged an international underground mining contractor to partner this development. This has enabled Roxgold to successfully develop the mine over a relatively short time frame with construction commencing in April 2015, first gold being poured in May 2016 and commercial production being achieved in October 2016.This paper discusses key elements of the project development and highlights some of the challenges faced with operating in a remote poorly developed area with a limited mining culture. Furthermore, the authors highlight the key technical and operational aspects that make the Yaramoko project a very successful development project.CITATION:Cope, B and Churi, Y, 2017. The development of the Yaramoko gold project in Burkina Faso, West Africa, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R Castedo, L. M. Lopez, J. A. Sanchidrian

In 2014 the authors presented results from 13 tests made with two blasting seismographs on a vibration exciter. They measured coupling transmissibility as function of frequency (i.e. ratio of the velocity of the sensor mount to the velocity of the ground motion) from 16 to 200 Hz at one or two vibrations levels (5 mm/s or 0.2 in/s, and 20 mm/s or 0.79 in/s) with mounts freely placed, sandbagged, and anchored to a granite slab firmly attached to the plate of a vibration exciter. As the memory capacity of one of the seismographs prevented to cover low frequencies, e.g. 4-16 Hz, a new measuring campaign has been recently made to extend the study down to 2 Hz. In this campaign, two more techniques, in which the sensor mounts were fixed with thermal adhesive or a combination of duct tape and gypsum plaster, have been also investigated from 2 to 200 Hz at 5 and 20 mm/s. Free and sandbagged mounts lead to a weak coupling of the mounts to rock, so that transmissibility depends on the characteristics of the imposed rock motion (peak velocity and frequency). Measurements are accurate only at low frequencies (below 17 Hz for free mounts and 10 Hz for sandbagged) in the tested conditions (velocities up to 20 mm/s). Above these frequencies, ground motion in the measurement can be modified by a factor of 0.16 to 1.22. Anchored, glued and plastered mounts achieve a stiff rock-to-ground coupling, ensuring consistent measurements for the frequencies commonly found in blasting independently of the vibration level and the mount characteristics

Jan 1, 2015

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By V. R. Miller

The Bureau of Mines developed and evaluated a detecting and sorting device to separate the copper-bearing portion from the barren portion of Michigan native copper ore in the minus 4- plus 1-inch size range. Small-scale sorting tests were also conducted on minus 1- plus 1/2-inch material from the Centennial No. 6 mine, using a previously developed system that was modified to increase sensitivity. Results showed that, with the added sensitivity, 85 to 90 pct of the copper in the minus 1- plus 1/2-inch material could be recovered in about 50 to 60 pct of the fraction. Sorting tests on minus 4- plus 2-inch and minus 2- plus 1-inch fractions from the Centennial mine were conducted with the large sorting system. Results showed that 86 to 93 pct of the copper was recovered in 43 to 64 wt-pct of the sorted fractions. Combining of concentrates from the two fractions resulted in a recovery of 90 pct of the Popper in 55 pct of the weight. The composite concentrate contained 2.40 pct copper, and the tailing analyzed 0.33 pct Cu; the head sample assayed 1.46 pct Cu.

Jan 1, 1978

By F. D. Everett

This report summarizes the results of a nationwide investigation completed in 1964 to determine the nonferrous base metal ore reserves and potential sources of ore and to evaluate criteria for their ultimate exploitation. Engineers of the Bureau of Mines contacted mining company officials, reviewed reports and Government records, and where necessary made personal appraisals in arriving at the results. The estimates are presented by metals in ores in geographic regions and include some of the problems affecting the reserves and potential sources. The recoverable metal in the measured ore category and in the total ore reserves was estimated as follows: [ ] At the 1963 rate of domestic mine production these total reserves would be adequate to provide copper for 62 years, lead for 121 years, and zinc for 42 years. Data also are given for gold, silver, and other coproducts. Reserve estimates greatly exceed those of previous investigations; some prior estimates of copper reserves are included for comparison (table 23). Projections of requirements for base metals indicated the United States will need approximately 45 percent more copper in 1970 and 110 percent more by 1980 than was consumed in 1960; similar projections for lead indicate increases of 20 percent by 1970 and 45 percent by 1980; zinc projections are 40 percent more by 1970 and 90 percent by 1980. Much of the production of gold and silver is a coproduct of base metals recovery and the projected need for the precious metals exceeds all the United States can produce. Some problems of the industry are mentioned. A graphic evaluation of the economic availability of the reserve and potential sources is shown.

Jan 1, 1967

By W. T. Abel

The rate of the steam-carbon reaction, which is of fundamental importance to coal gasification, was determined by passing steam over graphite specimens suspended in an electrically heated tube. The measurements were made at 1,900° to 2,400° F. and at steam-feed rates of 0.1 to 2.0 moles of steam per mole of carbon per minute. At the maximum steam-feed rate, the reaction rate of carbon ranged from 0.4 percent per minute at 1,900° F. to 7 percent per minute at 2,400° F. Up to about 2,200° F., the steam-feed rate had only a slight effect; above this temperature, it limited the reaction velocity when the final mole fraction of steam in the reaction products was much less than 1.

Jan 1, 1962

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By Forrest T. Moyer

To keep the mineral and allied industries informed of trend: in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

By I. Bhattacherya

Over the last three decades, the mining industry has been moving towards underground mechanized mining methods and the number of load haul dump (LHD) vehicles utilized has increased. The growth of mechanization and automation has benefited both workers and mining companies. However, due to the design constraints with LHD vehicles and the limitations of the operating environment, restrictions to operator visibility has contributed to a number of accidents, including fatal injuries. Past researchers have used the light filament technique to collect obscuration zones around mobile equipment and have produced 2D visibility charts (shadow diagrams) of this information. The light filament method involves manually collecting visibility data, which results in errors and is time consuming, requiring around three hours to complete. This research utilizes a MENSI GS100 laser scanner along with 3D modelling software (3Dipsos) to collect and process operator visibility profiles for underground mobile equipment. Results from this test work indicate that a laser scanner can be successfully used to rapidly collect this data and utilize this information for improved mobile equipment design from a visibility perspective. Nomenclature FERIC Forest Engineering Research Institute of Canada ISO International Organization for Standardization JACK Software for digital human modelling and ergonomics LHD Load haul dump vehicle LOS Line of sight MASHA Mines and Aggregates Safety and Health Association (based in Ontario, Canada) PVD Polar visibility diagram SAMMIE3D human modelling computer aided ergonomics design system WSIB Workplace Safety and Insurance Board

Jan 1, 2006

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024