Search Documents

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

By Ivor Hawkes

This report describes the results of a study to evaluate new design concepts for percussive rock drills that will result in quieter machines. It is shown that by incorporating such features as an efficient muffler, a plenum chamber integral with the machine body, and shroud tubes around the drill rods, etc., noise levels are reduced from about 114 dBA to about 95 dBA with very little change in drilling performance.

Jan 1, 1977

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle developed under U.S. Bureau of Mines Contract No. JO 366003, "Improving Man Transit Safety". This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements were embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery-powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle is presented in Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By A Cox

It has been demonstrated that all the cadmium from spent batteries, typically 4 g per battery, can be recovered by burning polyvinyl chloride waste to yield hydrogen chloride; this reacts to produce volatile calcium chloride, which can then be condensed and collected in a separate reactor. Alternatively, chlorine may be used to chlorinate the cadmium with equal efficiency. There is also a prospect of using very low concentrations of these gases, less than 1%, to effect the separation. The Cd was recovered more quickly when exposed to sustained, controlled flow rates of chlorinating gases, whereas when PVC was burnt most of the gas was produced in a very short time, not allowing complete reaction. This problem can be overcome by recirculation of the gas into the reactor. The technology is efficient and clean and the equipment used is simple, enhancing the prospects for a pilot-scale version of the process

Jun 21, 1905

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By S. R. Crane

One Bureau of Mines goal is to minimize the undesirable environmental impacts associated with industrial plants emitting waste gases containing S02. To help meet this goal, a regenerable flue gas desulfurization process was developed. This process, known as the citrate process, uses a buffered weak acid solution to absorb S02 from the waste gas. The absorbed S02 is reacted with H2S to precipitate elemental sulfur and regenerate the solution for recycle. The H2S feedstock for the process, if not otherwise available, may be produced by reacting two-thirds of the recovered elemental sulfur with natural gas and steam. Laboratory investigations and pilot plant operations were conducted by the Bureau to determine if H2S from the natural gas, sulfur, and steam reaction was suitable for the citrate process. The laboratory investigations, in which an H2S generator was integrated with other citrate process operations, provided a basis for design and operation of the pilot plant. The objective of the pilot plant was primarily to provide H2S for the citrate pro-cess pilot plant at the Bunker Hill Co. lead smelter in Kellogg, Idaho. The design capacity of the pilot plant was 0.4 to 1.25 tons of H2S per day. The operation demonstrated that (1) a 77-to 79-dry-volume-percent H2S product could be produced from pilot-plant product sulfur, natural gas, and steam; (2) the product R2S regenerated the SO2-loaded citrate solution; and (3) under certain conditions over 95 percent of the natural gas could be converted to H2S.

Jan 1, 1981

The sequences in alteration and mineralisation from five copper-gold porphyry systems (Taysan and Didipio, Philippines; Horse-Ivaal and Wafi River, PNG; and Goonumbla, Australia) and one gold-copper skarn system (Browns Creek, Australia) are documented in this paper. Alteration and mineralisation in all these systems reflect a common evolution from crystallisation of melts emplaced at shallow crustal levels (zoned potassic -> propylitic alteration), followed by exsolution of volatile-rich fluids from these melts (porphyry quartz ¦K-feldspar/biotite veins and local high temperature advanced argillic alteration), to a progressive cooling of the intrusion which results in associated retrograde alteration. Copper-gold mineralisation in all cases is almost exclusively restricted to the cooler retrograde events. The recognition of the temporal and spatial zonations in alteration and mineralisation in gold-copper porphyry systems has significant relevance in the interpretation of geophysical signatures, overprinting alteration, vein sequences and structural controls, and can lead to more focused and potentially more cost-effective exploration.

Jan 1, 1999

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

Jan 1, 1970

By Detlef Ehlert

In view of the increasing level of cost pressure on the part of plant owners, optimized plant operation with top product quality and maintenance costs is indispensable. Unscheduled shutdowns with increased repair costs and production downtimes are significantly reduced by preventive maintenance and the stock-keeping of spare parts. To remain competitive in the steel market, it is important for plants owners to operate their plants with the highest possible degree of energy efficiency and at high availability in order to manufacture high-quality products. Plant Monitoring Systems make it possible to optimize the manner of production. An integrated overview of the overall process, under consideration of process stability, product quality, production costs and plant availability ensures a “transparent plant”.

Aug 16, 2017

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By M. W. Hildyard, M. O. Kataka

Seismic integration schemes aim to incorporate the rock mass response provided by the historical seismic activity to improve the ability of numerical models to reproduce future response to mining. Up to now, integration schemes considered the events using quasi-static models. This paper presents case studies that consider some of the seismic and modelling issues needed to extend these schemes to include the dynamic characteristics of seismic events. The ultimate aim of an automated integration scheme seems impractical for dynamic modelling. The predictions of the WAVE elastodynamic finite difference program are, however, suitable for modelling limited numbers of events to determine either the near-field velocities and damage or the effect of fractures and excavations on the far-field low frequency response. Les projets d’intégration sismique ont le but d’incorporer la réponse de la masse rocheuse à l’activité sismique historique pour améliorer la capacité des modèles numériques à reproduire la réponse future à l’exploitation minière. Jusqu’à présent, les projets d’intégration étudiaient les évènements avec des modèles quasi-statiques. L’étude présente révèle des études de cas qui considèrent certaines des questions concernant modelage et séismes qui sont nécessaires pour porter plus loin ces projets en incluant les caractéristiques dynamiques des évènements sismiques. Le but final d’un projet d’intégration automatisé semble impraticable pour la modélisation dynamique. En revanche, les prédictions du programme élastodynamique par la méthode des différences finies WAVE sont appropriées à la modélisation d’un nombre limité d’évènements de façon à déterminer soit les vitesses à petite échelle et les dommages, soit les effets des fractures et excavations sur la réponse de basse fréquence à grande échelle. Seismische Integrationsschemata zielen darauf ab, Reaktionen der Gesteinsmasse, die von den Berichten seismischer Aktivitäten stammt, zu inkorporieren um numerische Modelle in die Lage zu versetzen, künftige Antwort zum Bergbau zu reproduzieren. Bis dato betrachteten Integrationsschemata die Fälle mit quasi-statischen Modellen. Diese Arbeit stellt Fallstudien dar, die einige der seismischen und modellierenden Fragen betrachten, die benötigt werden, um diese Schemata auszuweiten, um die dynamischen Charakeristika seismischer Fälle einzuschließen. Das Endziel eines automatisierten Integrationschemas erscheint für das dynamisches Berechnen undurchführbar. Die Vorhersagen des WAVE elastodynamisch begrenzten Unterschiedprogramms sind jedoch verwendbar für das Berechnen von begrenzten Anzahlen von Fällen, um entweder die Nahfeldgeschwindigkeiten und Schaden oder den Effekt von Brüchen und Extraktionen auf der Fernfeld Niederfrequenzantwort festzustellen.

Jan 1, 2003

The effect of microwave radiation on the processing of Palabora open pit ore has been investigated. Significant reductions in Bond work index are demonstrated for microwave treated samples. Reductions in work index were found to be sensitive to applied power level and method of application. After single stage magnetic separation tests, improvements in recovery of FeO were noted. However, these were curtailed by oxidation of the magnetite species as a result of continued heating. The effects of microwave radiation upon the recovery of copper after froth flotation were also quantified. Small initial increases in recovery of copper were note dafter microwave treatment. However, with prolonged exposure, recovery was found to decrease. Overall recovery of copper was not affected except for samples treated for extended duration. The influence of microwave treatment upon the conventional Palabora grinding circuit has been quantified with the use of USIMPAC software. Conclusions are made regarding the economics of microwave treatment for this ore. Keywords : Microwave; Grinding; Magnetic Separation; Flotation; Economic Analysis

Jan 1, 2000

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958