Search Documents

By Gordon Revey

Over ten million pounds of explosives are used daily to blast rock in mines, quarries and construction projects throughout the United States. Despite the immense volume of explosives used, serious incidents involving the legal use of explosive materials are rare. Unfortunately, when incidents arise they are well publicized, whereas the great majority of blasting projects-even the most challenging ones—quietly occur without incident or public recognition. Although unfair, media coverage focuses on incidents and/or accidents, and as a result skews the public’s perceptions of our industry. These negative perceptions about blasting profoundly effect our work. Most apparent are the community groups who organize to fight blasting work. However, other impacts are more insidious and have long-term effects on our industry. For instance, planning engineers or government agencies often prohibit blasting to avoid the public’s adverse reaction or because of general fear of blasting impacts. Ironically, as regulations and specifications continue to curtail our industry, the net effect is an increase in the cost of rock excavation. As taxpayers, we suffer needlessly by paying more for government funded construction projects. As blasting professionals we are additionally penalized through loss of work.

Jan 1, 2001

Development of Grindability Tests Based on Direct Measurement of Energy Nowadays, for the characterisation of the grindability different grindability indices - Bond-work index (Wi), Hardgrove Grindability Index (HGI) or Zeisel specific grindability (Wt) - are used. Generally, the grindability tests are carried out under relatively simplified circumstances, in a special dry batch mill with defined feed size material until prescribed conditions are reached at room temperature. However, in the fine- and ultra fine grinding, which is a frequent task (fly ash, tailings, alumina, etc), a fine material (<50 - 200 ¦m) is usually ground down to the few micrometers. The conventional grindability testing methods and apparatuses (Bond-, Hardgrove-, Zeisel-processes) for their determination, although, are not suitable directly to measure the grindability of such fine materials, since the maximal particle size of the feed material (0.5 - 3 mm) to be tested is much higher. One of the important goals of the research carried out in our Institute was to develop the novel grindability testing methods, which are suitable for the fine and ultra fine grinding, and additionally provide the possibility for the fast determination of the grindability. In order to realise the above aim the conventional Bond- and Hardgrove- mills were modified in order to directly measure the grinding work. In particular, the Hardgrove-mill was equipped with a simple torque-meter (load cell). The Bond-mill was rigged with a digital electric power measurer. The systematic experiments were carried out parallel in both mills using the conventional and the developed methods. Finally the results of both were compared. The measuring results have proved that the Bond-work index can be determined based on the developed methods. The new grindability testing methods were applied successfully in several industrial research tasks for the determination of the specific grinding energy and the Bond-work index. These methods can be also used in the industrial practice for the control of the grinding process.

Sep 13, 2010

By Kung-Lee Wang

SUSTAINED growth characterized the U.S. economy in 1964. Many new peaks were achieved in production, sales, employment, employee earnings, and business profits. At the end of 1964, the economy had experienced 4 years of uninterrupted expansion, and the greatest net gains in output for all postwar cyclical advances had been registered. There were no indications of the various weaknesses which have previously characterized advanced stages of business expansion. Both gross national product (GNP) and national income were 6.7 percent higher than in 1963. In 1964 GNP totaled $628.7 billion, a gain of $39.2 billion over the 1963 figure. On an overall basis, prices rose 1.75 percent in 1964. The real volume of output of goods and services (GNP in constant dollars) increased by 5.0 percent ill 1964; this was more than the 3.8-percent gain in 1963 but less than the 6.6 percent gain in 1962. The 1964 output gain also exceeded the average 3.7 percent annual increase for the postwar period. Congress authorized a two-stage tax reduction designed to further stimulate economic growth and employment. The tax cut favorably affected the 1964 economy in the following ways: By helping to boost personal income, corporate profits, and industrial production; by accelerating the pace of consumer spending and business capital expansion; and by increasing employment, thereby reducing unemployment to 5 percent. Three major problems remained unsolved. These were unemployment of 3.7 million persons, poverty conditions among more

Jan 1, 1965

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By Luis Valle, Fredy Zegarra, Ernesto Vizcardo

El uso de los procesos estocásticos y cadenas de Markov se ha desarrollado solo para estudios de probabilidades en la rama de las ciencias matemáticas y como una opción a las descripciones tradicionales en el campo del procesamiento de minerales, se realizó una comparación entre ambas metodologías para lo cual se cuenta previamente con varios análisis granulométrico proveniente de los molinos de Bolas industriales de la empresa Shougang Perú y pruebas granulometrías de Molienda de Sider-Perú, comparar en ambos estudios, como el probabilístico (Cadenas de Markov) y el cinético (Selección y fractura) ofrecen un buen acercamiento al resultado experimental, dando como una buena alternativa el primero por su uso del manejo estocástico.

Sep 1, 2017

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

Economic Sustainable Power for Mineral Processing

Sep 13, 2010

By William H. Pomroy

The Bureau of Mines, through a 4-year program of combined in-house and contract research, has developed the necessary hardware and software technology to provide rugged, reliable automatic fire protection for surface mining mobile equipment. One element of this program was a continuing effort to help foster rapid mining industry acceptance of the technology by keeping end user costs reasonable. This report is an analysis of the economic impact of surface mining mobile equipment fires and the cost benefit of utilizing automatic fire protection systems to abate these losses.

Jan 1, 1982

How to Evaluate Crushed Rocks for Concrete Production

Sep 13, 2010

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By C E. Davies

At present the source of virgin iron for steel produced in New Zealand is titanomagnetite extracted from titaniferous beachsands. Some of these beachsand deposits contain extractable quantities of ilmenite as well as titanomagnetite and both minerals represent challenging sources of vanadium and titanium products in addition to iron. This study looks at some theoretical aspects of smelting these ores directly with coal rather than with electric power, and takes into consideration the properties of the raw materials, the thermodynamics of possible process routes and the background of the economics involved.

Jan 1, 1980

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

The Johnny Mercer lyrics 'You've got to accentuate the positive, Eliminate the negative, Latch on to the affirmative à' would best sum up the traditional approach to community relations in the mining industry. This '90s 'Public Relations spin' approach, usually backed up by scientific data, technical reports and graphs outlining risk probability and the impact potential on people and communities, is being challenged. Challenged by communities who have greater access to information, demand greater levels of transparency and corporate responsibility of large corporate operations and possess greater awareness of the communities they live in.   The growth of the environmental movement, of anti-globalisation, anti corporatism, apprehension of a large corporate's ability to deal with community issues, and a lack of faith in the abilities of regulators to regulate corporate activities, means our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities.   One of the keys to this is linking the internal activities and responsibilities to the externals concerns and demands for higher levels of operation and care.   This presentation draws on Corporate Public Affairs trends, functions and approaches and the application to External Affairs activities within Newmont Waihi Gold's operations in Waihi and regional exploration activities throughout the Hauraki Goldfields.   The approach presented works on the philosophy that communities don't necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Jun 1, 2010

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By C M. Hall

We report 40Ar/39Ar ages for adularia and illite from veins and wall rocks at the Waihi and Favona deposits, in the Waihi district. One sample of vein adularia from the Favona deposit yielded a plateau age of 6.04 ¦ 0.06 (la) Ma, and two samples of vein adularia from the Waihi deposit yielded plateau ages of 6.17 ¦ 0.03 and 6.17 ¦ 0.09 Ma. Two samples of wall rock adularia from the Waihi deposit yielded plateau ages of 6.07 ¦ 0.06 and 6.08 ¦ 0.03 Ma. Adularia ages overlap at the 2s level, and we do not consider them to be significantly different. Two samples of illite from wall rocks at Favona have total gas ages of 5.66 ¦ 0.04 and 5.65 ¦ 0.04 Ma, and retention ages of 6.57 ¦ 0.04 and 6.61 ¦ 0.04 Ma, whereas one sample of vein illite yielded a total gas age of 5.29 ¦ 0.17 Ma, and a retention age of 6.26 ¦ 0.19 Ma. The total gas ages of illite are minimum ages that are equivalent to conventional K/Ar analyses, whereas retention ages of illite are maximum ages. Although interpretation of the illite data is complicated, the adularia results strongly suggest that the Waihi and Favona deposits formed contemporaneously in the same fossil geothermal system at 6.0 to 6.1 Ma.

Jan 1, 2003

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991