Search Documents

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By George C. Coupland

Ecstall Mining Limited, a wholly owned subsidiary of Texas Gulf Sulphur Company, is the owner and operator of the Kidd Creek Mine including the concentrator complex located near Timmins, Ontario. Canada, approximately 450 miles north of Toronto. The mine, concentrator and Timmins form a triangular arrangement with a 17-mile rail link connecting the mine and concentrator and both of these facilities 18 and 14 miles respectively by road from Timmins. A core drilling program in the spring of 1964 established the presence of a large massive sulphide orebody which was to become the Kidd Creek Mine. Texas Gulf Sulphur had been conducting an intensive search for base metal in various parts of Northern Ontario and Quebec since 1957. Of several thousand anomalies detected in airborne electromagnetic surveys, several hundred warranted ground inspection, but only one of more than sixty drilled became a commercial orebody, the Kidd Creek Mine. The geophysical exploration work has been well covered in a paper written and presented by Van Donohoo, presently a Vice-President of T.G.S., at the American Mining Congress in San Francisco in October 1969. GEOLOGY The orebody lies within a series of overturned rhyolitic flows and pyroelastics with a major peridotite intrusive to the east. The hangingwall and footwall are composed chiefly of intermediate volcanics, andesite and dacite. The southern end of the orebody appears to terminate abruptly against greywacke while the north end is bifurcated and the structure obscured.

Jan 1, 1970

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By W. Breytenbach

Traditionally, dithiocarbonates (xanthates) have been the preferred collectors for the flotation of platinum-bearing sulphides. However, collector development has led to trithiocarbonates (TTC), which have proven to be very effective bulk sulphide collectors. The interest in TTC flotation behaviour is currently focused on the interaction of these collectors with other collectors, specifically the dithicarbonates. Batch-flotation research has shown synergism to exist among dithiocarbonate, dithiophosphate and trithiocarbonate collectors. Increased sulphide recoveries, both for the first-minute and final concentrate, were realized using mixtures of these collectors relative to the standard.

Jan 1, 2003

By M. Lu, E. Broch

Abstract: The formation and mechanism of rock cavern roof arches are studied and effects of rockbolts reinforcement are evaluated. It is concluded that a self-supported roof arch may be formed by the excavation. To stabilize such a roof arch, fully grouted rockbolts are effective. Tensioned cable anchors may have a negative influence on the arch stability. Zusammenfassung: Die Formation und der Mechanismus von Deckenbögen in Bergkavernen wird studiert und der Effekt von Verstärkung mit Bergbolzen wird bewertet. Es wird festgestellt, dass die Exkavation einen selbst-stützenden / freitragenden Deckenbogen formen kann. Eingegossene Bergbolzen sind effektiv um einen solchen Deckenbogen zu stabilisieren. Spannkabel können unter Umständen eine negative Einwirkung auf die Stabilität des Bogens haben. Résumé: Le mécanisme et la formation de voûtes dans les cavernes rocheures sont étudiés et l'effet du renforcement par boulonnage est évalué. Nous arrivons à la conclusion qu'une voûte autosupportêe peut être formée par excavation. Des boulons entièrement scellés par coulis de bêton s'avèrent efficaces pour stabiliser de telles voûtes. Les tirants d'ancrage peuvent quant à eux nuire à la stabilité de la voûte.

Jan 1, 2003

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

By U. Olsson, M. Ramström

"The IREDES1 Special Interest Group (SIG) for drill rigs has been active since its launch during MineExpo 2000 in Las Vegas, Nevada, United States. SIG for drill rigs is responsible for the development of an IREDES drill rig profile, including the exchange of production planning, performance, and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During 2001, a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies, and third-party suppliers and reviewed during several SIG meetings. The profile for prototyping projects was released in mid-2002; the first official IREDES release was based on feedback received from these projects.In 2002, LKAB and Atlas Copco decided to carry out an IREDES prototyping project using the Simba L6C production drill rig. The goal was to verify the drill rig profile and identify potential problems prior to the official release. This was done by implementing the IREDES prototype version into LKAB’s production planning and Simba rig control systems. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this, the mine production system was adapted for drill plan export and logging data import in IREDES format.This paper presents the most recent results of the IREDES prototyping project. Results from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES, will be a central requirement for future mine automation.As a result of the IREDES prototyping project, the IREDES standard was approved at the IREDES board meeting held at the 2003 CIM Annual Conference and Exhibition. Soon thereafter, IREDES compliant products, including drill rigs and mine production planning systems, were put on the market."

Jan 1, 2005

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004

By K J. Thompson

This paper describes the work which has been undertaken at the Ohai coalfields in Southland to restore overburden heaps during past opencast mining operations, and procedures which have been adopted to ensure that restoration is achieved concurrent with present opencast mining activities. The system implemented for the treatment of wastewater from opencast mining operati6ns is also described.

Jan 1, 1981

By R. V. Ramani

This report is volume 3 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Methane Generator subsystem of the Master Design Simulator. This subsystem is used to determine methane emission rates into the mine environment. These flow rates are then used by the simulator in planning primary and secondary ventilation systems, planning a methane drainage system, and analyzing complex ventilation networks. Both steady state and unsteady state gas flows are included, and have been modeled as second order nonlinear partial differential equations. Finite difference equations are used to obtain numerical solutions to the models using a central differencing scheme. An application of the model is presented. The appendices include derivation of the gas flow equations used in the model as well as a users manual for the computer program.

Jan 1, 1974

By Steve Kral

The mining industry in northern Ontario is known mostly for its huge nickel deposits. Inco’s and Falconbridge’s nickel mines in the Sudbury Basin are the best known. And with nickel prices being what they are, interest in the region continues. And how. Inco and Falconbridge want to merge. Teck Cominco wants Inco, but without Falconbridge. Xstrata made a hostile bid for Falconbridge, which Falconbridge rejected. And, in June, Phelps Dodge trumped them all when it made an approximately US$40-billion friendly offer for Inco and Falconbridge in a two-part deal.

Jan 1, 2006

By Ken Norris

"Campbell Mine which has been in continuous operation since 1949 has undergone numerous operational changes in the past 3 years. This paper describes the process changes which have occurred at the Campbell Mill since 1991. The paper discusses the engineering, construction and startup of the effluent treatment circuit, the new oxide filtering and merrill-crowe precipitation circuit, and the changes to the pressure oxidation circuit. Particular attention is paid to startup problems and solutions to these problems. A review of the benefits and results of these process changes is also discussed. Future changes are also briefly reviewed with anticipated goals and expectations.IntroductionCampbell Mine is a gold mine 100% owned and operated by Placer Dome Canada. It is located in Balmertown, Ontario which is located 300 kilometres northeast of Winnipeg, Manitoba. The Campbell Mine has been in continuous operation since 1949, producing nearly 8,000,000 ounces. In 1993 Campbell Mine is budgeted to produce 289, 750 ounces of gold at a cash cost of $157 US/ounce. Daily mill tonnage is budgeted for 1,430 tons/day but has milled as high as 1,600 tons/day on a consistent basis. Recovery in 1993 is 93.4% and is budgeted to average 94.5% in 1994.In the 1992 edition of the proceedings of the Canadian Mineral Processors conference I described the changes that were made at Campbell starting in 1989. This paper continues where the 1992 paper ended and discusses the changes to the Campbell mill since that lime. The changes to Campbell since January 1992 have been numerous with capital expenditure in the mill exceeding $14.1 million. This paper describes three primary projects since that lime: the effluent treatment project ($5.5 million), the oxide leach/filtering and merrill-crowe project ($4.6 million) and the pretreatment project ($2.81 million). The focus of this paper is to highlight the justification of each project, the design and engineering, and some of the initial operational problems and solutions applied to those problems."

Jan 1, 1994

By S. W. Stogran

"Chemical and limited biological monitoring of mine and mill effluents are being used by regulatory agencies to monitor and control discharges to the environment. Amendments to the Federal Fisheries Act may make it mandatory for mines to conduct Environmental Effects Monitoring (EEM) which will change the emphasis from monitoring effluents to monitoring impacts on receiving waters. The EEM amendments may expand the scope of present environmental studies to include: effluent mixing zone delineation; inventory and classification of resource, habitat, and historical receiving environment; effluent quality determination; chronic and acute bioassay testing; tissue analysis; benthic invertebrate monitoring; fish population surveying; fish tainting evaluation; and the evaluation of impacts on fish habitat, invertebrate communities and fisheries resources. The requirements for EEM have not yet been worked out by the mining industry and the government committee. Experience at Lakefield Research in conducting biological monitoring studies for the mining industry has shown that biological monitoring may be useful for assessing environmental impacts only if programs are planned and executed to collect relevant data, thus minimizing costs and maximizing effectiveness.IntroductionThe chemical monitoring of effluents and water bodies receiving effluents is common practice in the Canadian mining industry and has been used routinely by regulatory agencies to control discharges to the environment. Biological monitoring has also been used on a limited basis, primarily to augment chemical data collected. A number of regulatory bodies, primarily in Canada and the United States, have been incorporating biological monitoring into environmental regulations.Various forms of biological monitoring techniques have been used in Canada and the United States to help assess the impact of mining operations and effluents on the environment. Biological monitoring includes a wide range of activities, from monitoring metal uptake in individual organisms to examining the population dynamics in ecosystems. The most commonly employed biological monitoring techniques are the chronic lethality toxicity tests. Also becoming widely used are in situ and chronic toxicity tests."

Jan 1, 1994

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983