Search Documents

By Eddy Dierckx

Modernization of flat rolling plants is essential to sustainably fulfill increasing market demands and to improve competitiveness. Intelligent modernizations ensure getting maximum prime yield of existing mills, even if they have gone through half a century of operation. Existing mills were designed based on former production, consumption and quality targets. Ever increasing requirements such as increase of productivity, change of product mix (e.g. new steel grades), reduction of energy consumption and improvement of product quality lead to the necessity to adapt the existing equipment to the new target. SMS group provides, besides the reliable equipment and automation solutions to successful upgrades of existing mills, also a systematic approach to develop technical and economical solutions together with our customers (conceptual engineering). This paper describes the SMS group approach to modernizations / upgrades, introduces powerful performance modules and provides a number of successful examples that have been implemented recently.

Aug 17, 2017

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017

By Sunil Katharia

In February 2016, the upgraded Blast Furnace 1 of JSW Steel Limited (JSW) at its Vijayanagar Steel Plant was blown in after a 6 months shutdown in which the whole furnace was rebuilt on the existing foundation and within the existing tower structure. Despite several plant constraints it was possible to increase the furnace inner volume by 85% - reaching 2307 m3 from existing 1250m3. The upgradation project covered the stockhouse and its dedusting system, top charging system, furnace profile, furnace cooling system, casthouse and its dedusting system, slag granulation plant, pulverized coal injection plant, hot blast system and gas cleaning plant – with major interventions in order to cope up with the changed operating conditions. The total scope of the project was split by JSW into several packages, all based on design data provided by Paul Wurth. JSW was responsible for coordinating the local subcontractors along with Paul Wurth which has been appointed as main technology supplier in charge of complete basic and selected detail engineering in the key areas and of the supply of core equipment such as the Bell-less Top®, copper staves, GCP key items and TMT casthouse machines. The main design concept and the key points of the project such as optimization of project ROI, advanced erection concepts as well as a summary of the operating results are presented confirming JSW “BF1” upgradation as one latest examples of the current state of the art in the revamping projects.

Aug 17, 2017

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By Andreas Rohrhofer

Reliable high end automation and process optimization systems are main factors for excellent product quality, safe operation and maximized plant performance in the steel industry and its designated environmental plants. Primetals Technologies introduces new automation packages for consequent safe and cost efficient production. Many areas within the steelplant interested to be monitored and measured automatically are not implemented in the automation system due to limited access or technical reasons. A wireless, self-organizing network facilitates wide ranging data transmission in previously inaccessible areas and opens up a wide range of new opportunities. With Fluid Guard a system to detect leakages with highest accuracy and reacts properly for all kind of water cooled circuits is available, improving the safety in steelmaking process. Lance Guard can be utilized for all fully automatic and semi-automatic lance appliances, but is especially suitable for the products of Primetals Sublance Standard/2.0 and LiquiRob applications, since these systems make seamless integration particularly simple. Manual lance appliances may also be tested and diagnosed. Environmental plants have become a main part in steelmaking plants. Highest performance in combination with optimized energy consumption is the main target in Primetals Technologies’ innovations in automation optimization packages for dedusting systems. A new approach for preventive maintenance and operator assistance is introduced with the Acoustic Expert System. In combination with the new Ask cloud based system, Primetals enables a 24/7 monitoring and a whole lifetime observation of any equipment within a steelplant. Furthermore it is now enabled to check the condition of the plant at a fingertip at any time.

Aug 17, 2017

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Mark Gilliam

Control of true steel level in the tundish during casting is desired in order to maintain the correct pressure head and thus provide a stable flow to the mold. Also the control of tundish draining prevents slag carryover and can increase yield at each end of cast sequence. At Steel of West Virginia (part of the SDI Group), it was understood that to be able to measure the true steel running level and control the drain level at the end of casting would be a great benefit during production at their three strand billet caster. This paper sets out to show how an evaluation process was started to find the best method to determine steel level in the tundish and to prevent the steel level dropping low enough to allow slag to enter the mold. Also how the decision was taken and a real time molten steel measurement system was installed and by utilizing the resulting data in the process, how slag in the mold was removed as an issue, how lost production was reduced and how consistent steel level has provided constant casting speeds and improved stream integrity, all leading to realized quality improvements. Other areas discussed within the paper will be the training of operational staff, the difficulties to be overcome when first installing new equipment and how these teething problems were cured by close co-operation between the steel plant and the equipment suppliers. In conclusion the paper will discuss the production improvements achieved, production cost savings at the plant and how the generated data was integrated into the plants process control system.

Aug 16, 2017

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Frank Schrama

The Steel Plant Model (SPM) is an advanced logistic simulation model for steel plants. With the SPM, bottlenecks can be solved and logistics can be optimized. Both existing plants and greenfield designs can be simulated. All movements and actions simulated, from hot metal to cast products. Not only all major equipment and their relevant components (like a sublance) are simulated, but also ladles, scrap boxes, transfer cars and cranes. The whole plant is simulated in 3D and actual distances and speeds determine transport times. The SPM includes process time deviations and equipment downtimes for maintenance or unexpected breakdowns. This ensures more realistic and reliable results. Logistic optimization is based on comparison of different scenarios. For a new scenario, equipment and practices, etc. can easily be modified, added or removed. At the same time the SPM produces all relevant data for every new scenario, which can be presented conveniently. This makes the SPM the ultimate tool to find bottlenecks or optimize plant logistics. The SPM is validated for several plants world-wide, with different characteristics and layouts. The SPM not only realistically simulates existing plants with all utilizations, crane movements and waiting times, but also to accurately predicts the influence of plant modifications or unexpected events like breakdowns. Given the flexibility of the SPM, any (new) steel plant can be simulated quickly when a layout and the requested data are provided.

Aug 16, 2017

By Ernst Lindemann

Steel suppliers are required to deliver sheets with particular qualities and with lightweight-potential to the automotive industry. New types of steel call for new production processes. SMS group has developed a new micro-mill-concept, the core of which is the belt caster. This was first built on an industrial scale and has been put into operation and developed together with Salzgitter Flachstahl GmbH. The robustness in industrial-scale operation could be verified. The full use of the belt casting technology, mainly related to energy efficiency and CO2 reduction, is realized with the micro-mill-concept. This is an in-line-process, casting and rolling in one line.

Aug 17, 2017

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Horacio Destaillat

Desde hace aproximadamente 15 años se encontró por experiencia empírica que se puede “neutralizar” el efecto del plomo sobre la maleabilidad en caliente de cobre proveniente de la refinación térmica de chatarras mediante control de la composición química. Este hallazgo ha resultado de aplicación industrial. Si bien el contenido porcentual de plomo se reduce por refinación convencional y con cierta facilidad hasta 0,02 – 0,03 %, este valor es elevado [1] para laminar en caliente. Bajar el nivel de plomo hasta los valores exigibles por normas, requiere procedimientos especiales y costosos. La técnica cuyo mecanismo aquí se investiga, consiste en ajustar el contenido de plomo y estaño dentro de ciertas proporciones, ya que el balance de estos elementos, permite proceder sin problemas de fisuraciones a la colada y laminación en línea del cobre. Con el control de la composición química del sistema se logra que el plomo y el estaño se adhieran [2] sobre las partículas de eutéctico Cu-Cu2O. Esta disposición micro estructural en borde de grano explica la acción favorable del estaño en la maleabilidad. El procedimiento que aquí se describe no es aplicable a cualquier caso pues no funciona en materiales con contenido elevado de oxígeno (“Tough pitch”) ni en cobres desoxidados. Solamente lo hace en formas de baja sección que hayan sufrido enfriamiento rápido.

Aug 7, 2018

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Julio Aníbal Morales Pereira

The capacity of steelmaking slags (CaO-SiO2-Al2O3-MgO) on inclusion removal from liquid steel was investigated through experimental conditions. Laboratory experiments with slag and steel samples (with inclusion population known) were performed using a vertical electric resistance furnace at 1600 ºC. After the melting experiments, slag and steel samples were separated and analyzed regarding their chemical composition and inclusion population evolution. The capacity of slags on inclusion removal was evaluated based on the thermodynamics (solid and liquid phases proportion, phase composition and effective viscosity of slags) calculated using the FactSageTM 7.2. Results indicated that changes in the composition of slags (regarding CaO/SiO2 e Al2O3) presented effects on the steel cleanliness. The total inclusion density decreased in all steel samples and the removal of inclusions by slags shows a tendency to improve as their viscosity decreases (< 0.23 Pa.s).

Oct 1, 2019

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017