Search Documents

By S. E. Clay, G. P. Martins, P. R. Taylor

A grain model for gas-solid reactions in cylindrical pellets is formulated and solved numerically. The numerical solution demonstrates when it is safe to assume either a thin disk or a long cylinder geometry, and when the more general two dimensional geometry must be used. The numerical solution also demonstrates the solution of a two-dimensional moving boundary problem (i.e., when the reaction is diffusion controlled and the ratio of the height to diameter dictates two dimensions).

Jan 1, 1986

By Edward H. Robie

MANY engineers currently are working harder than usual, in part because of the demands being made upon them for increased production in the war effort, and in part because engineers are in short supply so that there is more to do for those who are available. In some instances the question has come up as to what additional payment, if any, should properly be made for overtime work, and to what extent is such payment legally permitted under the rules of the Salary Stabilization Board. Most engineers employed in an executive, administrative, or outside salesman capacity are not paid for overtime. They are paid for doing a job instead of for the hours they put in, and are free to do all the unpaid home work they feel they should do after dinner, as well as to do a bit of thinking and worrying during wakeful hours in bed. But engineers employed in a strictly professional capacity normally have standard office hours. Some employers pay for overtime and some don't. Their practice as it existed on Jan. 25, 1951 may be continued. In the absence of such practice at that time, the Salary Stabilization Board says that the engineer may now receive additional compensation up to his straight-time rate for an extended work week. No formal approval of the Board is required. "A professional engineer," in the mind of the Board, "is a person employed in a professional capacity, who, by reason of his special knowledge of the mathematical and physical sciences and the principles and methods of engineering analysis and design, acquired by professional education and practical experience, is qualified to practice engineering." Inducted Engineers A letter from a young man just inducted into the service and fearful that his engineering training is not going to be utilized reached us last week from Fort Riley, Kan. The AIME, cooperating with the other Founder Societies, is doing what it can, through the Engineering Manpower Commission, to see that engineers are not being wasted in the military establishment. So we passed this young man's letter along to T. A. Marshall Jr., executive secretary of that Commission. Mr. Marshall tells us that the normal procedure now being followed by the Army in handling Selective Service inductees is to have them first complete 16 weeks of basic training before assignment to specialized categories. During that time they are classified. If one has an engineering degree he should be classified as scientific and engineering personnel at the end of the basic training period. He should then be transferred to a technical detachment and assigned an MOS (Military Occupational Specialties) reflecting his education. If a young man is looking for a commission, it might be added that the current policy in the Army is to transfer to OCS (Officer Candidate School) applicants for commissions in the infantry only. The local unit commander can give information on this point, based upon the aptitude shown in tests. In view of the current shortage of engineers, it is believed that a young man should seriously consider remaining in enlisted status unless he can obtain a commission in a branch of the service that can make full use of his technical skills. His work may thus be more to his liking even if his uniform is not. New York or Atlantic City? In which place is it preferable to hold the annual meeting of a professional society like the AIME-New York or Atlantic City? That is, a winter meeting. The American Society of Mechanical Engineers has held its recent meetings at Atlantic City, with increasing attendance and satisfaction. The American Institute of Chemical Engineers chose Atlantic City for its recent December annual meeting. Only twice has the AIME ever met in this famous seashore resort: in 1898 and 1904. Chief advantages of going to Atlantic City over New York are that technical sessions are better attended, there being little else to do there in Winter; the cost to members is less, and hotel facilities are better adapted to a large meeting. As to cost, take a banquet, for instance. The Chalfonte-Haddon Hall, which caters especially to winter conventions, charges about $7 for a banquet dinner of standard quality. A similar dinner at the Statler in New York would cost about $8.50, and about $10.50 at the Waldorf-Astoria. (The charge for tickets is somewhat greater than this because of the cost of music, programs, flowers, and other incidentals.) Rooms, too, are somewhat less at Atlantic City, two in a room being accommodated for about $7 per day each, compared with $7 to $10 at a headquarters hotel in New York. On the other hand, AIME headquarters is put to some extra expense for staff travel, food and lodging, and members living in New York and environs are forced to pay a hotel bill. New York, of course, has more varied amusements to offer, plenty of big stores, and the glamour of a big city. The choice may be discussed at the forthcoming meeting in New York. In the meantime if any reader cares to express an opinion one way or the other we shall be glad to hear it. College Scholarships Most parents of children in the later stages of high school find it necessary to give some consideration to the cost of a college education. Although salaries have increased substantially it seems that the cost of the necessities of life, such as food, housing, and maintaining the family automobile, have gone up even more, so the problem of financing the children's education is as acute as ever. Many overlook the possibility of scholarships, or feel that only a student at or near the top of his class has a chance to get one. As a matter of fact, close to 150,000 scholarships and more than 15,000 fellowships, worth some $42,000,000, are available in 1200 American colleges and universities. Those who are interested should send 55¢ to the Superintendent of Documents, Government Printing Office, Washington 25, D. C. for a 248-page publication just issued by the U. S. Office of Education, entitled "Scholarships and Fellowships Available at Institutions of Higher Education."

Jan 1, 1952

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By Rufus J. Foster

During the discussion on the Preparation and Utilization of Sniall Sizes of Anthracite (page 613 of present volume), several inquiries were made concerning the use of the McClave grate, which was mentioned by Mr. Coxe as having proved satisfactory in the generation of steam at his collieries, and also at a large number of industrial estal)lishments in Scranton and elsewhere. For a more satisfactory repIy to such inquiries than could be furnished in the oral discussion, I have prepared the following paper to be included in the published proceedings. And, as the use of the fuel under consideration necessarily requires the employment of a blower to change the fire, from a condition giving an incandescent radiant heat only to one giving a hot gaseoua flame as well, I shall add a description of the McClave Argand blower and its method of action. The grate and blower combined form a complete and effective system fcr burning small fuels, such as anthracite culm, birdseye, buckwheat, bituminous slack, etc., in boiler and other furnaces; while the grate alone is now extensively used with the larger sizes of hard and soft coal in furnaces where blast is riot required. Fig. 1 is a view of the RlcClave grate as built in two sections. It is constructed on the principle best approved by practice to prevent warping and burning out; that is, it presents no long lines of

Jan 1, 1892

By John A. Church

The operations of the Tombstone Mill and Mining Company, in Arizona, have been extensive and interesting; and I will eudeavor to describe what is novel in their work, without attempting to go over the well-known facts of silver milling, concentration and smelting which are the general branches of their business. Their mines are at Tombstone, and their mills at Charleston, ten miles distant. The ore has been mined only above water-level, and at first was

Jan 1, 1887

By D. C. Seidel, E. F. Fitzhugh

The Colorado School of Mines Research Foundation has developed a hydrometallurgical process for recovering nickel from oxidized ores, including both the iron-rich laterites and magnesium-rich, soft silicates. Known as the HSO-HTCP (Hydrothermal Sulfidization Oxidation-High Temperature Cementation in Pulp) Process, the system consists of feed preparation, sulfidization, oxidation, precipitation (cementation), and calcination and melting. This paper deals primarily with the sulfidization and oxidation phases of the process. Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types — the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of gamierite and related nickeliferous silicates are found.' The gamierite veinlets, however, are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass. Pyrometallurgical processes account for nearly all the nickel currently being recovered from oxidized ores. Plants in New Caledonia, Oregon, Japan, Brazil and Greece smelt the ores to make ferronickels or a sulfide matte,2 and the ammoniacal leaching3 at Nicaro, Cuba, is preceded by a reducing roasL4 The only fully hydrometallurgical installation has been the politically ill-fated Freeport Nickel Co. enterprise, and this process was limited to lateritic ores.5p6 A hydrometallurgical technique which might handle both laterite and the typically richer silicate ores has been an enticing goal. The technique described here was developed at the Colorado School of Mines Research Foundation, Inc. on behalf of the Republic Steel Corp. It uses sulfur, heat, air and metallic iron to recover nickel from these ores. Inasmuch as the ores are treated as aqueous slurries, the cost of drying a plant feed that normally carried 30% or more moisture is eliminated, and there are no dust problems. Patent applications have been filed by Republic Steel Corp. on the procedures used for getting the metal into solution and on the subsequent recovery without liquids-so l ids separation of the slurry. It is referred to as the HSO-HTCP Process (Hydrothermal Sulfidization Oxidation — High Temperature Cementation in Pulp). THE PROCESS FLOWSHEET The results of various experimental studies have been combined to form the continuous flowsheet illustrated in Fig. 1. This flowsheet serves as a general pattern showing the sequence of the operations which include: (1) feed preparation; (2) sulfidization; (3) oxidation; (4) precipitation (cementation); and (5) calcination and melting. This paper deals primarily with the sulfidization and oxidation phases of the process. Feed preparation: In general, the silicate ores can be considered as earthy rather than hard, and preparation might be carried out before the addition of water in a trommel, or with water in a scrubber or log washer. This breaks up the earthy particles, allowing the hard lumps to be separated by screening. The oversize material from most ores is relatively barren and may be discarded. If there is occasion to control the iron-magnesium ratio in the plant feed, laterite, which normally breaks up readily into fine sized particles, and silicates are mixed in suitable proportions. The fine product slurry from the initial steps is mixed with elemental sulfur and fed to a conventional ball mill, although the amount of actual grinding that takes place is relatively small. The object of milling is to complete the disintegration to natural particle size and to produce an intimate mixture of the ore and elemental sulfur. This pulp, which is almost entirely -200 mesh, has a pH of about 7.0 and normally can

Jan 1, 1969

By H. E. Cline, J. L. Walter

Grain boundary sliding and migration were studied in pure aluminum bicrystal and polycrystal samples with two-dimensional grain structure. Scratches, 50 P apart, were used for measurement of sliding and migration distanceso. Samples were deformed at constant rate at 315C and events recorded continuously on wrotion picture film. Electron micrograPhs of boundary-scratch intersections were obtained. Yield and flow stress values were measured. The sequence of sliding and migration events for a three-grain junction is described in detail. Sliding depended only on the resolved shear stress imparted to the boundary. Sliding was accowmodated by formation of shear zones in grains opposite triple points and adjacent to curved boundaries. These shear zones provided the driving force for grain boundary migration. Migration caused rumpling of the boundaries, decreasing the sliding rate. Sliding and migration generally began at the same time, occurred simultaneously and ended at the same time. In the bicrystal, sliding and migration rates were proportional. Initial sliding rules of 5 X joe cm per sec. were measured for the polycrystal and bicrystal samples. These sliding rates agree wilh the internal friction experirnents of K;. The observations seem consistent with a viscous boundary sliding nzechanism. GRAIN boundary sliding is the translation of one grain relative to its neighbor by a shear motion along their common boundary. Sliding is thought to be an important mode of deformation at elevated temperatures and at low strain rates such as prevail in creep,' and perhaps in the area of superplastic behavior.2"4 Although much work has been done to investigate grain boundary sliding, the effort has not led to the identification of a mehanism. KG showed that grain boundaries in aluminum exhibit a viscous nature under very small displacements of internal friction measrements. Various dislocation mechanisms have been proposed but are without conclusive experimental support. Attempts to relate sliding to 6's viscous boundaries have been unsuccessful in that measured rates of sliding are always several orders of magnitude lower than KG'S results would predict.= In bi crystals7and polycrystalsR of aluminum tested under constant load, the grain boundary sliding was found to be proportional to the total creep elongation which indicated that sliding might be controlled by deformation of the grains. Shear zones were observed to extend beyond grain boundaries at triple points to accommodate the sliding.8 Surface observations brought forth the opinion that sliding and migration occurred alternately, in sequence.' Measurements of sliding at the surface have been criticized because they might not be representative of the interior of the sample. Generally speaking, it seemed that much of the previous work and knowledge was based on observations made at relatively low magnification and examination of samples after deformation had been accomplished. Thus, it was the purpose of the present study to continuously record, at high magnification, the events occurring during the deformation of pure aluminum. Samples with two-dimensional grain structures were used to simplify interpretation of the results. The sliding and migration of small areas of many samples were continuously recorded by time-lapse motion pictures. Replicas of the surface were used to provide high-resolution electron micrographs. These observations, coupled with tmsile strength data, provide sufficient information to arrive at an understanding of the phenomenon. EXPERIMENTAL PROCEDURE An ingot of 99.999 pct A1 was rolled to sheet, 0.127-cm thick. Tensile specimens, with a gage length of 0.85 cm, were machined from the sheet. Bicrystal tensile specimens, of the same dimensions, were spark cut from a large bicrystal ingot. The grain boundary was oriented at 45 deg to the tensile axis. The surfaces of the tensile samples were ground flat on fine metallographic paper and were then electropolished in a solution of 75 parts absolute alcohol and 25 parts of perchloric acid. The solution was cooled in an ice-water bath. Using a weighted sewing needle suspended from a small pivot on a precision milling machine, a grid of fine scratches, 50 p apart, was scribed on one surface of the sample. The polycrystalline samples were then annealed in hydrogen for 15 min at 350" to 400°C to produce a two-dimensional grain structure of about 0.2-cm average grain diameter which would not undergo further growth at the test temperature, 315OC. Examination of both surfaces of the samples showed that the grain boundaries were perpendicular to the surface of the polycrystal and bicrystal samples. A hot-stage tensile machine was constructed for use with an optical microscope as shown in Fig. 1. The specimen is shown mounted in the grips. The grips ride in V-ways so that the sample can be mounted without damage. The rear grip is free to slide so that when the sample expands during heating it is not put under a compressive stress. When the grips and samples are at temperature, the rear grip is locked in place by two set-screws. The other grip is connected to a synchronous drive motor which, through a worm gear and a fine-threaded rod, deforms the

Jan 1, 1969

By R. C. Himes, K. Zanio, J. B. Wagner, J. W. Moody, J. F. Miller, W. Johnson

The recent research with which this paper deals has been concerned with the preparation of pure PbTe crystals suitable for control of radiative processes and othe.v electronic applications. The research has been directed toward the developrnent of methods for the preparation of puve, homogeneous, loul-ca,wier-density PbTe crystals suitable for use in the fabrication of optically pumped and electrically pumped diode lasers. Steps in the preparation of the crystals include 1) purification of the starting materials, 2) synthesis and purification of the PbTe, 3) growoth of PbTe crystals, and 4) adjustt~zertt of composition of the crystals This Paper describes the general preparation procedure employed and discusses some investigntiotzs of purification processes. THE as-received lead and tellurium are nominally 99.999 to 99.9999 pct pure. Assays furnished by the suppliers, obtained by emission spectrographic analysis, show only the presence of about 2 ppm Mg in the tellurium. Such analyses are not very informative, however, since they give no information on the concentrations of normally gaseous impurity elements such as oxygen. Both the lead and the tellurium in the as-received state usually contain appreciable concentrations of oxygen—primarily in the form of oxides on the surfaces of the material. To reduce the oxygen content, the lead is held in the molten state in hydrogen at -700°C for several hours. For this treatment, the lead is contained in a graphite boat which is rf-heated, and the hydrogen is passed through a liquid-nitrogen trap prior to use. Tellurium is subjected to multiple distillation in hydrogen to remove oxygen and other foreign impurities. If, in conducting the distillation, approximately the last 10 pct of the charge at each "stage" is left as the discard cut, purification of the tellurium proceeds as indicated in Fig. 1.l Tellurium used in this work has been distilled two or three times to reduce carrier concentration to about 10" per cu cm. The PbTe is prepared from the purified elements by reacting them in the molten state in sealed, evacuated, or hydrogen-filled silica ampoules. The charge is usually held above the melting point of PbTe (923°C) at 1000 C for 24 hr to ensure that it has been homogenized. Two methods have been employed for the growth of the required single crystals of PbTe: growth from the melt, which will be discussed first, and growth from the vapor phase. Large single crystals of p-type PbTe can be grown readily from the melt by the Bridgman method. For this method of crystal growth, the PbTe is synthesized in situ from proper proportions of the purified elements. Growth (dropping) rates in the range 1.3 to 6.5 mm per hr are employed. Material near the maximum melting composition (about 50.012 at. pct Te) is utilized to avoid composition change on freezing, and thus to obtain crystals of nearly uniform composition. Crystals prepared by use of procedures described up to this point were sufficiently pure and perfect that they could be used for the preparation of laser crystals in studies at Lincoln Laboratory.2-5 ADJUSTMENT OF COMPOSITION Good n-type crystals of PbTe cannot readily be grown from the melt. Further, growth from the melt of crystals of any compositions (n or p type) other than those near the maximum melting composition is difficult because of the large composition changes that must occur on freezing.'" However, melt-grown crystals can rapidly be brought to other desired compositions by isothermal equilibration through the vapor phase with a two-phase Pb-Te stock material, essentially as described by Brebrick and Allgaier.1 The work to be discussed has been concerned with the preparation of n-type crystals; thus, the two-phase stock which was employed contained excess lead, and all ensuing discussion is of the preparation and properties of n-type crystals. The equilibration was designed to the shift composition to the lead-rich limit of stability at the selected temperature. Initial treatment of the crystals at high temperature was employed to minimize the total time required for the equilibration. Final adjustments of the composition and state of the crystals were made by use of low-temperature heat treatment at temperatures in the range 200" to

Jan 1, 1968

By Fred P. Dewey

Although coke is the acknowledged metallurgical fuel, and has been extensively used in this country for more than thirty years, yet the facts on record in regard to its physical properties are exceedingly meagre; and this is also true, but in a less degree, of its chemical composition. An investigation is being carried on in the National Museum which is intended to supply, so far as may be, this deficiency, and through the kindness of Professor Baird, Director of the Museum, I am permitted to present to the Institute a summary of a portion of the results already obtained. So far as I am aware, the credit for the first systematic investigation of the physical properties of coke belongs to Mr. John Fulton, Mining Engineer of Cambria Iron Co. The results of this investigation have been published in Report L, Second Geological Survey, Pennsylvania, 1875, and in a pamphlet setting forth the advantages of the Connellsville coke, the latter published also by the " Virginias"* His results are not altogether free from experimental errors, and the assumption that "the specific gravities of coke and water are very nearly alike "- is scarcely warranted. It has seemed to me, therefore, desirable to make an independent investigation of the physical properties of coke on a plan somewhat different from that adopted by Mr. Fulton. This is the investigation now being carried on at the National Museum.

Jan 1, 1884

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson' have described the geologic setting of the mineralization. The sulfides, believed to be syngenetic, include chalcopyrite, cubanite, pentlandite, pyrrhotite, and minor amounts of bornite. They occur disseminated in the silicates and as small interstitial masses. The ratio of copper to nickel is about 3.8:1, based on 66 chemical analyses of rock samples from various outcrops (Ref. 1, p. 702, and Ref. 2). Test Procedures: With specified exceptions, all nickel and copper tests were made by the chromo-graph method,:' which measures the intensity of a colored spot formed by a reaction between the metal being determined and special reagent paper. The intensity is then compared to the intensity of spots prepared from samples of known metal content. Details of the test procedure are outlined in another article (Ref. 4, pp. 77,78). All soil samples tested in this investigation to date have been weighed on an analytical balance. However, a volumetric scoop designed to provide about 0.1 g of soil adds to the speed and ease of testing and has been found to give satisfactory results (Ref. 5, p. 531, and Ref. 19). The size of the samples used for the tests was 0.1 g. Whenever such small samples are used there is some question as to whether they are representative of the several grams in the field sample. Many repeat tests of the samples used in this investigation demonstrated that results can be reproduced within the limits of accuracy of the method without formal mixing beyond that inherent in screening the soil fractions. Furthermore, the 0.1 g is probably as representative of the field sample as the field sample is of its area of influence. Hawkes and Lakin (Ref. 6, p. 291), who considered the general problem, compared ground and quartered bulk samples of 500 g with 5-g grab samples. They concluded that "there is no significant loss in accuracy of data by substituting grab samples for bulk samples." The term soil implies somewhat different things to the geologist, engineer, and soil scientist.' For convenience the term as used in this article refers to unconsolidated material (the mantle) overlying bed rock. Sampling Procedure: Samples were taken at 100-ft intervals along north-south traverse lines across the gabbro-granite contact. The soil (till) samples were taken at an average depth of 1 ft, which was below the high-humus surface layer and into clean till. Samples taken at 1-ft intervals down to ledge showed as high a metal content at 1 ft below the air-surface as at greater depths and in two instances were slightly higher. The till at 1-ft depth did not appear to differ from material at greater depths. Total depth to bedrock has been tested at only a few points and where measured varied from 1 to 10 ft. Aerial Distribution Contours and Profiles: Plotting of copper, nickel, and cobalt content in contour form (Fig. 2) shows that anomalous amounts of these metal ions occur in till over and closely adjacent to mineralized areas of the gabbro. Contouring nickel content alone, or the copper content, outlines the same target area. Contours of the copper content provide a more distinct anomaly than nickel because of the higher copper concentration. The traverses are rather widely spread for interpolation; however, drilling has confirmed the target area essentially as shown.

Jan 1, 1959

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

POSITIONS VACANT The National Bureau of Standards needs men to fill metallurgical positions with salaries varying from $1200 to $2000, depending upon the training and experience of the candidate. Experience either in ferrous. or, non-ferrous metallurgy. Duties will be almost entirely of an investigational nature, in connection with problems of military importance. Qualified men are urged to send to the Bureau of Standards at once a statement of training and experience, names of references, acid minimum salary that would be accepted, so that they may he advised of appropriate civil service examination for which to file papers. Until further notice, such papers are received by the Civil Service Commission at any time and ratted promptly.

Jan 10, 1917

By George M. Enos, Robert J. Anderson

This paper gives a summary of tests made on the accelerated electrolytic corrosion of the tin brass, 70:29:1 copper-zinc-tin (admiralty metal), of different grain sixes in various electrolytes. There has been great difference of opinion as to the effect of grain size on the corrosion rate of brass, particularly in condenser-tube practice, but so far as is known no information has been published on the subject. It has been assumed, on the basis of the amorphous-cement theory, that fine-grained brass would corrode more rapidly than coarse-grained because the amorphous phase is more soluble than the crystalline and there is more cement per unit area exposed in the fine-grained material. In previous work on the corrosion of metals and alloys in acid mine waters from coal mines,1,2 it was found that the grain size, within a restricted range, had practically no effect on the corrosion of the brass 70:29:1 copper-zinc-tin: In the tests made, samples of three grain sizes were included; viz., 0.025, 0.035, and 0.075 mm. diameter (1600, 817, and 177 gr. per sq. mm., respectively), and the average losses on exposure to the most acid of three waters were 7.07, 6.80, and 6.72 mg. per sq. cm. per day (24 hr.), respectively. No distinguishing features were observed on microscopic examination of the corroded samples. In two other mine waters, the corrosion losses were substantially the same for the respective samples. These tests were -incidental to other tests and were not sufficiently comprehensive to warrant drawing definite conclusions. In further work with the accelerated electrolytic corrosion test, as developed recently in the Bureau of Mines, tests were made

Jan 1, 1924

By F. N. Lathe

In 1882, The Arizona Copper Co., Ltd., acquired producing copper mines at Metcalf and Morenci (locally called Longfellow). Metcalf is situated a distance of 7 miles, and Morenci a distance of 6 miles from the general office of the company at Clifton, Ariz. A reduction works with five blast furnaces was built in the center of the town of Clifton in 1884 and operated until January, 1914. Concentration of oxidized ores was begun in 1890-1891, in a mill built adjoining the smelter, and id October, 1893, a leaching process was started for treating tailings from the oxide mill. A sulphide concentrator with 300 tons capacity was built at Clifton and started treating chalcocite ores in July, 1896. This was the first mill to treat low-grade copper-siilphide ores successfully. Another concentration mill for sulphide ores was erected at Morenci in 1900. The sulphide mills are now being remodeled to treat ores by concentration and flotation, with a capacity of 4,000 tons at Morenci and 500 tons at Clifton. The leaching plant has not been running since September, 1914. The average yearly production from this company's mines and reduction works from 1885 to date has been: Pounds 10 years ended 1894................................... 6,864,902 10 years ended 1904................................... 20,439,614 10 years ended 1914................................... 32,665,905 Part of year 1915, to Sept. 12........................... 30,206,106 4 months of 1916, to June.............................. 15,964,840 June, 1916........................................... 4,900,000 Construction on a new smelting plant was started in February, 1912, and finished in February, 1914. In the Transactions, vol. 49, E. Horton Jones published "Unit Construction Costs from the New Smelter of the Arizona Copper Co., Ltd.," which fully describes the construction of this plant, with details of costs.

Jan 1, 1917

By R. W. Snyder, H. J. Ramey

This paper presents the results of applying the Buckley-Leverett' displacement theory to petroleum reservoirs consisting of a finite number of layers. The layers are assumed to communicate only in the wellbores, and the reservoir may be represented as a linear system. Most previous investigations of this nature were limited by assumptions and by inconsistent calculation techniques. This study improves on previous work by applying the Buckley-Lev-erett displacement theory to a noncommunicating layered system where permeability, porosity, initial saturation, residual saturation and relative permeability vary from layer to layer in a logical and consistent manner. Gravity and capillary-pressure effects are neglected. A modification of the Higgins-Leighton calculation method was used in this study. Waterflood predictions were made with all properties varying, and then with only permeability varying using several inability ratios. These results were compared with the Stiles and Dykstra-Parsons predictions. It is shown that the latter methods generally give poor values for the breakthrough recovery and pessimistic predictions for the performance after breakthrough. Similar results were obtained for a gas-displacement case. lNTRODUCTION Field experience with immiscible displacement usually shows constant producing conditions until breakthrough of the displacing fluid. Then oil production continues at increasing displacing-to-displaced fluid ratios until the economic limit is reached. Three different ideal mechanisms are known that will produce this behavior: (1) relative permeability effects as described by Buckley-Leverett frontal advance theory,' (2) vertical stratification as considered by Stiles,2 Dykstra and Parsons5 and others and (3) different path lengths involved in areal (two-dimensional) flow between wells as described by Dyes et al.4 Without question, a combination of these factors modified by formation heterogeneity and other known and unknown factors actually does control the behavior of real systems. This paper presents results of an investigation of certain factors that should affect performance but which have received little attention to date. In 1944, Law5 demonstrated that porosity and perme- ability are often found to have normal and logarithmic-normal distributions, respectively. throughout cored intervals in natural formations. This led to the concept of the noncommunicating, multilayered reservoir model for immiscible displacement. This model assumes that the reservoir is composed of a number of layers that communicate only at the wellbores. Each layer is individually homogeneous, but may be different from every other layer. Stiles' presented one of the earliest applications of this model to waterflood performance. In addition, Stiles assumed that the initial saturations and relative permeabilities were the same for each layer, porosity was the same. displacement was piston-like, fluids were incompressible and injection into each layer was proportional to that layer's permeability capacity (permeability-thickness product). The last assumption would be true if the mobility ratio for the displacement were unity.21 Dykstra and Parsons" used the same model as Stiles, but rigorously included mobility ratios other than unity for piston-like displacement. Dykstra and Parsons used their general result to produce charts for log-normal permeability distributions between layers. Similarly, Muskat6 Pub1ished analytical solutions for linear and exponential permeability distributions. In 1959, Roberts' described a scheme for calculating water-drive performance for the noncommunicating, layered reservoir model which considered two-phase flow in the displaced region. Roberts used the same model and assumed that the injection rate into a layer was proportional to that layer's permeability capacity, but that flood front locations could be evaluated from the Dykstra-Parsons results. These assumptions are inconsistent, and a material balance cannot be maintained except for a mobility ratio of unity. At the same time, Kufus and Lynch8 coupled Buckley-Leverett displacement theory with the layered model to provide an improvement of the Dykstra-Parsons method that was consistent. In 1960, Higgins and Leighton9 resented a numerical method for calculating waterflood performance also considering two-phase flow in the displaced region. The result was used to investigate variation in absolute permeability and oil viscosity. An excellent, detailed history of using the noncomrnunicating, layered reservoir model was presented by Nielsen.'" The preceding techniques (and many related ones) were similar in that differences in initial saturations, residual saturations and relative permeabilities from layer to layer were neglected. It is well known that the irreducible water saturation is an important function of absolute permeability. Calhoun11 showed that the irreducible water saturation

By Ole Singstad

THE legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer, and this staff was given a number of problems to solve, such as location, size, type of tunnel, method of construction, method of ventilation and cost. After a period of preliminary investigations and studies it was decided to build the tunnel at Canal St., New York, connecting 12th St., Jersey City. This is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels-one for west-bound traffic and one for east-bound traffic-the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear heat room of 13 ft., 6 in. This is to provide for two lines of vehicles in each direction. The tunnels have an exterior diameter of 29 ft., 6 in. The interior lining is of concrete, the sidewalls tiled with a vitreous white tile and the roadways paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. BASIS OF VENTILATION It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character.

Jan 8, 1926

By T. Sterry Hunt

I HAVE already referred to this interesting locality in the opening address, but at the request of some of the members of the Institute, brought before them specimens of the ore and the accompanying rock. The ore, which is cassiterite, is also met with elsewhere in Maine, at Paris and Hebron, but it there occurs associated with orthoclase, quartz, tourmaline, and beryl, in concretionary granite veins, which cut the micaceous gneisses of the White Mountain series. At Winslow the veins traverse an impure gray micaceous limestone, which is found in many parts of this region, and is subordinate to the same gneissic series. The veins, which are seldom more than an inch or two in thickness, are abundant through a considerable breadth of the rock, and are interlaminated with it, occupying places between the sedimentary layers, which are distinctly marked by different shades of color. Occasionally, however, they cut across the stratification for a little distance, showing that the disrupting action was not always confined to tearing the layers apart. The vein-stone consists of purple fluor-spar, and silvery white mica with quartz. In this gangue the cassiterite, nearly black in color, is disseminated in small crystalline masses, sometimes one-half an inch in diameter, and is associated with a little mispickel. I have only seen the veins as exposed at a single point, but was informed that similar veins holding the ore are met with at a distance of several thousand feet

By S. R. B. Cooke, H. S. Choi, D. H. Harraway, I. Iwasaki

The mineralogy of natural iron ore samples and their slimes have been investigated and the nature of slime interference in iron ore flotation has been studied. The results have been correlated with the flotation behavior of a natural ore sample. Various conclusions have been reached as a result of these studies. In the flotation of iron oxide ores, desliming is generally considered to be an essential step to successful separation, irrespective of whether the iron oxide or siliceous gangue minerals are to be floated, although some workers have found empirically that certain collectors and reagent combinations are less sensitive to the presence of slime than others. The detrimental effect of slime is considered to be twofold. First, the presence of slime presupposes a high reagent consumption because of high specific surface. When clays are present and when cationic collectors are used abstraction by ionic exchange may augment this condition. Attempts to compensate by the addition of large amounts of reagent result in only partial correction. Second, slime coatings on granular particles tend to interfere with the bubble-mineral contact. The nature of slime coatings in flotation is quite complex and has been the subject of considerable study; an attempt was recently made by Fuerstenau et al.' to relate the slime-coating density with flotation recovery and with the properties of the electrical double layer at the mineral surfaces. Although major constituent minerals in the oxidized iron ores of the Mesabi and Cuyuna ranges are hematite and goethite (limonite) as the iron oxides, and quartz and chert as the siliceous gangue, very little is known of the mineralogy and of the chemical and physical characteristics of the slimes, and still less of the interaction between slimes, collector, and the mineral surfaces. For pragmatic reasons iron ore slimes are defined as — 20p material, based upon the calculated settling velocity of a quartz sphere of the stated diameter, and of all other equal-settling mineral particles. Active slime interference with flotation is usually attributed to particles 5p in size or finer, the extent of such interference appearing to depend not only on the mineralogy but also on the size distribution of each mineral in the slime fraction. The objective of this work was to acquire a more specific knowledge of the constitution of iron ore slimes and of their role in flotation. The mineralogi-cal composition of natural slimes was obtained by differential thernal analysis (hereinafter referred to as DTA), electron microscopy, and chemical and X-ray analyses. Some flotation tests were made on natural ore samples. The surface properties of several constituent minerals were investigated by electrophoretic measurements and by determination of the adsorption of some typical flotation collectors. Finally, simplified flotation tests were made on granular goethite and quartz in the presence of various artifically prepared slimes; the results were compared with laboratory flotation tests made on natural ores. MATERIAL AND METHODS Mineralogy of Some Iron Ore Slimes: Samples of two wash-ore tailing::, hereinafter identified as A* and B, *Sample A of the present investigation 18 the same am ore A in ref. 3. of a wash ore C, and of a paint rock D, all from the Mesabi range, were selected for investigation on the basis of prior information concerning their flotation behavior. The two wash-ore tailings, when deslimed, were known to respond well to flotation, whereas the wash ore was high in goethite, tended to be slimy, and responded poorly to flotation. The paint rock also exhibited sliming tendencies, and was suspected to contain relatively large quantities of clay minerals because of its high A1203 content. Gruner states that the paint rock of the Mesabi frequently contains kaolinite. To ascertain the relative sliming tendencies of each sample a standardized desliming method was employed. All samples were ground through 65 mesh using jaw and rolls crushers. A 500-g sample of each

Jan 1, 1962

AFTER the aforementioned subjects, I wish to speak to you of the method of welding bells that are cracked. This seems to me an ingenious thing, little used, but of great usefulness. Bells are cracked by the blows of too large a clapper or by excessive and forced ringing. This often cracks them at the rim, in the heart, or in some other place so that they lose their tone because of these cracks, and give no more

Jan 1, 1942

By Nicholas J. Grant, Henry Epstein, John Chipman

FOR many years steel producers have been concerned with the presence of hydrogen in steel. Hydrogen dissolved in excess of its solid solubility at the melting point may cause bleeding and gross unsoundness in ingots and castings. In fully-killed steels the hydrogen content which results in these difficulties varies with the alloy content1 and may range from 6 to 12 ppm.* It is also recognized that of heat treatment diminishes rapidly as the size of the part to be treated increases. The time required to remove a specified fraction of the hydrogen present increases as the square of the diameter of the section, making the treatment of large- sizes impractical. In order to prevent bleeding and gross unsound-ness due to hydrogen, and in view of the inadequacy of corrective heat treatment alone to provide optimum properties when hydrogen is present in large sections, efforts to limit the hydrogen content must be taken while the steel is still liquid. The main subject of this paper is a discussion of the factors affecting the hydrogen content of liquid steel in acid and basic open hearth, and basic electric two-slag furnace processing. Literature Survey Because many of the results and observations reported in the literature have a direct bearing on the results obtained in the present research and form part of the basis for conclusions reached, a brief summary of the findings is necessary. Methods for experimental investigation of hydrogen in liquid steel are comparatively new. The first attempts to estimate the hydrogen content of the open hearth bath were by Kalling and Rudberg,6 who devised a method for collecting gases evolved from the boiling bath of a basic open hearth furnace. They found that the gas during the boil generally contained 2 to 3 pct H2. From this and Sieverts'

Jan 1, 1958