Search Documents

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By E. S. Greiner

THE hot working of chromium was first reported by Hunter and Jones; who used small pellets of the material obtained by the reduction of chromium chloride with sodium. Later, the working of chromium at 600° to 1100°C was reported by Marden and Rich,2 and at 1250°C by Kroll3 The hot rolled material3 had a Brinell hardness of about 150 (62.5 kg, 2.5 mm ball, 1 min) and was brittle at room temperature. Except for that associated with hardness indentations, no plastic flow in chromium at room temperature has been reported to the author's knowledge. Studies described here have shown slip markings in chromium after deformation at room temperature.

Jan 1, 1951

By A. H. Tousley, C. L. Vickers

The author presents a history of the development of the Port of Long Beach from its beginning in 1905 to the present construction of a new bulk loading facility. In describing this new facility, emphasis is placed on such aspects as rail car and truck handling, gravity yard, rotary car dumping, bottom dumping, car dumping equipment, feeding and conveying, ship-loader-stockpiler, stockpiling and reclaim, dust control, and construction problems. Development of the Port of Long Beach, Calif. (see Fig. I), began in 1905. In that year private Long Beach interests acquired 800 acres of marshland in the Inner Harbor area and initiated a program of channel dredging and land reclamation. Efforts to establish a municipal port began a short time later and culminated in the opening of Pier 1 in 1911. An event of even greater significance to the port future also occurred in 1911. This was the tideland grant enactment by the state legislature that conveyed to the city of Long Beach all of the state's rights in the tidelands located within the city boundaries. The grant stipulated that all revenue produced from the tidelands be used for the development of navigation, commerce, and fisheries. During the next 15 years up to 1926, the port's commercial growth was steady, although relatively slow. During this period, several fundamental steps in the development of a major harbor were accomplished. These included the creation of the Board of Harbor Commissioners in 1917, the dredging of the Inner Harbor and entrance channel to accommodate deep draft vessels, and the correction of a serious silting problem through construction of the Los Angeles River Flood Control Channel. These efforts bore fruit during the ensuing 10 years in the establishment of more than $30,000,000 worth of industrial plants and private marine terminals in the Inner Harbor. Commerce over municipal wharves also increased more rapidly, and it became necessary to start the development of the harbor in a seaward direction. In 1936, oil was discovered in the harbor area, and the first Harbor Dept. well was brought in 2 years later. It soon became evident that the city of Long Beach would receive substantial revenue that, under the terms of the state grant of 1911, must be used in the development of the port. It was further realized that to properly guide and coordinate such development, a long range comprehensive plan was essential. The Board of Harbor Commissions contracted with G. F. Nicholson and J. F. Collins, consulting engineers, for the preparation of such a report that was completed in 1940. The Nicholson-Collins report proposed the development of an East Basin, between the entrance channel and the Los Angeles River, and a West Basin in the area now occupied by the Long Beach Naval Shipyard. Twenty full-size berths were to be provided in the East Basin and more than fifty berths in the West Basin. The report recommended extensive modern terminal facilities for handling waterborne cargo. Attention was given to improvement of the street and highway system to give better vehicular access and to avoid congestion within the port. To a large extent the recommendations of the Nicholson-Collins report were followed in the subsequent development of the East Basin. This development was greatly accelerated by World War 11, with its need for increased oil production and additional shipping facilities. The wartime and immediate postwar construction was largely concentrated on Pier A, with the development of Piers B, C and D following in more recent years. An important factor in the planning of these piers was their dual function as oil drilling sites and cargo piers. The Navy's acquisition of the West Basin area made it necessary to depart from the Nicholson-Collins plan and find other areas for future expansion. At the present time only one Inner Harbor Port-owned area having protected deep water frontage remains undeveloped. This is the property fronting on Channel 2 in the Inner Harbor acquired in December 1957, from Pacific Dock and Terminal Co. The growth of the port has been in a southerly direction since the construction of the Long Beach Naval Shipyard in the West Basin area. Recent extension of Piers F, G and J into the ocean follows typical port construction methods developed during the expansion of the Middle Harbor during the last 20 years.

Jan 1, 1963

By R. M. Fowler, H. L. Hamner

DURING the last 25 years, there appeared in the literature a number of papers describing equipment and operating techniques for the determination of total oxygen in iron and steel. In the early papers, comparatively little attention was paid to side reactions that occur when iron is saturated with carbon at a high temperature in a high vacuum. As more experience was gained with the new method, the limitations appeared. Metals, with a boiling point lower than iron, distilled out of the crucible, condensed in the cooler part of the furnace, and subsequently reacted with carbon monoxide to form oxides and carbon. Aluminum, manganese, and the alkaline earth metals proved troublesome in this respect. Modifications have been devised to overcome the difficulties due to aluminum and manganese, while the alkaline earth metals are not of too much concern as yet to the steel chemist. The reactions of sulphur have received less attention, although it is generally recognized that some carbon disulphide is probably formed. Liquid air traps have been used in some cases to prevent any carbon disulphide from entering the analytical train. Sulphur was not a particular problem at the Union Carbide and Carbon Research Laboratories until the analysis of the irons of higher than usual sulphur contents became necessary. In order to describe the procedure developed for such irons, it will be necessary to first describe the type of vacuum-fusion equipment employed because the operation of vacuum-fusion equipment is an art to a considerable extent. At the Laboratories, vacuum-fusion equipment has been in daily operation since about 1930. Over the years, the evolution of this apparatus has been governed by the versatility required to analyze a wide variety of materials. Since all types of materials from high purity metals to slags are analyzed and, since seldom more than a few samples of one type are analyzed in succession, the apparatus was designed for accuracy and flexibility rather than for speed. A general view of the equipment is shown in Fig. 1, while Fig. 2 shows the relationship of the various parts. In Fig. 2, A is a vertical double-glazed 24X27/8 in. OD silica tube heated with a 20 kva mercury-arc high frequency generator. The tube is closed with a water-cooled brass head attached with de Khotinsky cement. A turret cap fits on this head and is sealed with a 1/8x3 in. "0" ring. The head contains a sight glass and two 8 in. horizontal glass tubes, for sample storage, cemented in with de Khotinsky cement. B is a four-stage Gaede mercury diffusion pump connected to the water-cooled head with a 11/2 in. copper tube through a flange with an "0" ring. The output of the vacuum pump feeds into an automatic Toepler F pump which compresses the gas sample over mercury in the measuring burettes, G and H. There are bypasses in this line for a McLeod gage C and a Piranni gage D, a manometer E, and for initial pumping out of the system with a Cenco Megavac backing-up pump. The reduction crucible shown in Fig. 3 is machined of Tungar Bulb quality (A.G.K.T.E.-2) graphite. The sample is guided into the crucible with the graphite funnel depicted on this figure. The arrangement of the crucible, radiation screens, etc. in the furnace is as follows: A 1 15/16x61/2 in. Alundum thimble, porosity RA-84, with two 1/8 in. holes near the top and opposite each other which take a pair of special tongs used for lowering it in place, is prepared. A 3/4 in. layer of powdered graphite is placed in this Alundum thimble, and the graphite crucible containing 20 g of ingot iron and 0.5 g of carbon is carefully centered on this bed of graphite powder and graphite powder is packed around it to the top of the graphite cru-

Jan 1, 1953

By Frank J. Windolph

Grinding Practice-These tests were run in the 9 ft diam by 8 ft long grate discharge ball mills at Climax. Each mill functions in closed circuit with a 78 in. Akins duplex high-weir classifier, and a circulating load of 300 pct is maintained. The size of the mill feed is 6 pct on 3/8ths, which is ground to pass 28 mesh. Testing Methods-Each grinding section is equipped with a conveyor scale on the ball mill feeder belt, a watt-hour meter on the ball mill motor, and an automatic sampler for the ground product. These instruments are exceptionally valuable to the mill testing program.

Aug 1, 1956

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the 'Juniors' spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have 'a piece of the action.' The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the 'long shots,' many of which efforts by virtue of the Junior's perseverance coupled with a touch of 'ore is where you find it' philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach's results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K' = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By AIME AIME

IN times of stress nations pick strong men to lead them. Similarly the Coal Division selected forceful Larry A. Shipman, fuel engineer for the Southern Coal and Coke Co., Knoxville, Tenn.. to lead it through the year 1945. He was born in Indianapolis May 13, 1891. Following graduation from a technical high school in that city Larry began his fuel career approximately 35 years ago attached to one end of a scoop shovel, firing locomotives for the Pennsylvania Railroad. At the end of two years he transferred to the New York Central Lines and held these jobs successively: locomotive fireman, engineer, fireman instructor, supervisor of instructors, and fuel engineer.

Jan 1, 1945

By H. A. Deans

A three-parameter mathematical model for one-dimensional flow in porous media is developed. The objective of the model is to predict accurately the longitudinal dispersion associated with the flow of either gases or liquids over a wide range of Reynolds number. A qualitative analysis of the model parameters is given. Published experimental pulse-response curves are compared with results predicted by the model. Several general types of problems are given for which the model can be used. INTRODUCTION The problem of multicomponent single-phase flow through porous media is encountered in the study of petroleum reservoirs, gas chromatographic and ion-exchange columns, industrial fixed-bed con-tacters and elsewhere. These particular examples span the wide range of flow conditions possible; Reynolds numbers of less than l0-4 are not unusual in oil-production problems, while values in excess of 103 are common in large fixed-bed operations. The study of flow-dependent transport phenomena is complicated both by the changes in the character of the flow over this range, and by the irregularity of the flow boundaries inherent to porous media. Dispersion is one of the important phenomena known to depend fundamentally on flow conditions as well as on fluid and medium properties. As used in this paper, the term "dispersion" refers to the observed mixing of fluid elements of different composition which occurs in flow systems. The actual mechanism may be one or more of a number listed below. Only dispersion in the direction of the mean flow (referred to as axial or longitudinal dispersion, or mixing) is considered here, although lateral dispersion arises as part of certain coupled mechanisms. MECHANISMS FOR LONGITUDINAL DISPERSION A number of distinct mechanisms are known3,5,7,8 to contribute to the phenomenon of longitudinal dispersion. The more important of these are as follows. 1. Molecular diffusion in the flow direction. 2. Turbulent (cell) mixing. 3. Lateral transport processes coupled with velocity and/or residence time distributions, including: (a) "Taylor" diffusion caused by the interaction of velocity profiles in individual voids with lateral molecular diffusion; (b) separation and remixing or interdiffusion of streams having different velocities around particles; and (c) the couplipg of gross velocity profiles, caused by viscous instability or inhomogeneous porosity, with lateral dispersion. 4. Finite mass-transfer rate between a porous matrix and the flowing phase, and finite diffusion rate inside elements of the porous matrix. It is a well documented fact that these mechanisms, whether acting individually or in combinations, produce essentially similar integral effects. The observed dispersion can be described approximately by solutions of the diffusion equation with a properly chosen dispersion coefficient. Necessary conditions for equivalence between dispersion and diffusion are discussed by Klinkenberg and Sjenitzer.7 Apparently these conditions are not satisfied exactly in many real systems. "Best fit" solutions of the diffusion equation often depart appreciably from measured breakthrough curves for the usual pulse- or step-forced experimental systems. In particular, pulse response curves usually show some degree of asymmetry and "tailing" which cannot be reproduced by the one-parameter diffusion model. The three-parameter model proposed herein attempts to produce these effects in a realistic manner. Asymmetry and tailing are predicted for certain sets of parameter values, while for other sets the new model agrees with the diffusion model. VELOCITY DEPENDENCE OF DISPERSION Molecular diffusion apparently controls at sufficiently low Reynolds number in both gas and liquid systems.*l3 At Re > 20, turbulent cell mixing is dominant for gases flowing at low pressure; the data of McHenry and Wilhelm8 show that the mixing cell is approximately 1 particle diameter long in random sphere packs. on the other hand, the data

LIBERIAN ore has been called the richest iron ore mined in the world, and thus far, the output from the Liberian Mining Co.'s Bomi Hills mine has lived up to its reputation. Iron content has been variously given as 68.47 pct to 68.825 pct. A recent United Nations survey gave it first place, surplanting the previously top-rated Swedish product. The first shipment of Liberian ore to the United States reached Baltimore in June, 1952 and went into blast furnaces at Republic Steel's Cleveland plant, where excellent results were reported. The physical make-up of the ore was hard, dense lumps, free of fines and with ideal size distribution. The Bomi hills mines were scheduled to be in full operation by the end of 1952. At the close of 1951, 200,000 tons of ore had been delivered to Baltimore. Liberian Mining Co. states that production is about 90,000 tons of ore per month at present. Between 1200 and 1500 men are employed at the mine site, with about 25 pct of them Americans. The Bomi Hill project was financed with the aid of the Export Import bank, which loaned Liberia Mining part of the sum needed to initiate and put the development into production. No definite expansion plans are in the making but extensive diamond drilling is being pursued. Original estimates of annual production for Bomi Hills ran in the neighborhood of 1.5 million tons, but the figure is no longer applicable. Liberia's potential as an iron producing country has been known for a long time, but the physical obstacles in the way of large scale production were such as to prohibit even contemplation of the project. Until recent years, the only route from the mine site to Monrovia was a foot trail. Once to the coast, over swamps and unbridged rivers, the ore was still useless because of the lack of loading facilities. Transportation Solved One problem was solved with the completion of the artificial harbor at Monrovia. Harbor construction was well under way when the mine project began in 1948. The island location of Monrovia also made the building of a bridge across the St. Paul River necessary. The 980 ft reinforced concrete structure, accommodating railroad and vehicular traffic, was opened in 1949. Meanwhile, preliminary work on railroad construction started. Grading was completed quickly. In April, 1951, the first train made the trip from Monrovia to the Bomi Hills. About half of the cost of the entire project went into railroad construction. More than 2200 men, often forced to resort to primitive methods, were engaged in clearing a path through the heavy forests between the mine and port. Swamps were drained and filled, and bridges, including the William V. S. Tubman, named for the Liberian President, were constructed. At the port, a Robbins Conveyor Belt Co., orehandling plant was installed. Ships can be loaded from the stockpile at the rate of 3000 tons per hr and vessels need spend only one day in port. Liberian Mining is operating under an 80 year lease, giving the company exclusive mining rights to all minerals, except gold, platinum, and diamonds, within a 40 mile radius of Bomi Hills. The contract provides a fixed royalty to the Liberian Government of five cents per ton of ore extracted, and a premium -based on the New York market price for Bessemer-grade pig iron. The entire project started because an American,

Jan 1, 1952

By Walter Rose

In a recent technical note, Owen Thornton&apos; suggests that wetting liquid relative permeability may be derived from the relationship: where Pd/Pc is the ratio of displacement pressure to capillary pressure at the wetting liquid satdration Sw, and I is the resistivity index at this saturation. Thornton shows that this expression gives values for relative permeability in good agreement with those experimentally determined by Leverett. We have recently developed another expression for krw which seems preferable to Equation 1 since it requires fewer experimental data for its verification. This equation may be derived in the following manner. Making use of the analogy between mass transfer of fluid in a porous medium and electrical conductivity through the fluid in the same medium, we can postulate a hydraulic formation resistivity factor analogous to an electrical formation resistivity factor. From Poiseuille&apos;s Law the resistivity to flow in a tube of radius R is of the form 8u/R², where is the viscosity of the fluid. Similarly7 the resistivity to flow in a porous medium of the same dimensions as the tube is given by D&apos;Arcy&apos;s Law as where k is the permeability of the medium. The hydraulic formation resistivity factor, Ff, is thus the quotient of these two resistivities, or: But permeability is defined by the KO-zeny equation as: where: r is the average pore radius of the porous medium, L. is the average tortuous length of the average pore, + is the porosity, and L is the bed length. This gives Fr as a function of the (La/L) .-.-.tortuosity ratio and porosity, or in explicit form: where: T = (La/L)&apos;, and N is the number of pores of radius, r, which will be found in any cross sectional area, x R&apos;. That is, N = R²/r². It will be clear from the foregoing considerations that the hydraulic formation fat. tor should be dependent on the value of R which in every case must be arbitrarily selected. By analogy, the hydrauiic formation factor, Fcf, characterizing the porous medium at Sw<1,will be given by: R² NT. where ke is the effective wetting liquid permeability obtaining at Sw<l, and Te is the square of the (Las/L) ratio defined by Thornton. Therefore, the hydraulic resistivity index, If, is: However, Thrnton gives I as: and it follows that: Equation 2, when checked against the data of wyckoff and Botset² and some of the Morse et al data³, gives comparisons as shown at the bottom of this page. Computations based on Leverett&apos;s data, quoted by Thorntaon, gives computed krw values somewhat lower than the experimental values. Moreover, other instances can be cited where we find that neither Equation 1 nor Equa tion 2 is checked by experimental data. The work of Botset&apos; on the Nichols Buff sandstone and Morse et a1 on oil wetted Bradford sandstone are such instances. A reason for these discrepancies may lie in the fact that if both Equations 1 and 2 are presumed always to give accurate values for krw, it follows that PC = Pd/Sw". Such an expression, it is well known, is too simple to describe accurately the capillary pressure behavior of all porous media. However, it is believed that a particular advantage resides on the use of Equation 2, since it is not dependent for its utility on a knowledge of the capillary pressures obtaining in dynamic flow svsterns. No practical technique for measuring the capillary pressures characterizing the fluid distributions in dynamic flow systems has yet been proposed. Acknowledgment is given to Dr. Paul D. Foote, executive vice-president of the Gulf Research and Development Company, for permission to publish this note. 1. Owen F. Thornton, "A Note on the Valuation of Relative Permeability," J. Pet. Tech., 1:7, Section 1, July, 1949. 2. R. D. Wyckoff arid H. G. Botset, "The Flow of Gas-Liquid Mixtures through Porous Media," Physics, 7:325-345, 1936. 3. R. A. Morse, P: L. Terwilliger, .and S. T. Yuster, "Relative Permeability Measurements of Small Core Samples," Oil and Gas J., 46:109-125, Aug. 23, 1947. 4. H. G. Botset, "Flow of Gas-Liquid Mixtures Through Consolidated Sand," Trans. AIME, 136:91, 1940.

Jan 1, 1949

By Walter Rose

In a recent technical note, Owen Thornton&apos; suggests that wetting liquid relative permeability may be derived from the relationship: where Pd/Pc is the ratio of displacement pressure to capillary pressure at the wetting liquid satdration Sw, and I is the resistivity index at this saturation. Thornton shows that this expression gives values for relative permeability in good agreement with those experimentally determined by Leverett. We have recently developed another expression for krw which seems preferable to Equation 1 since it requires fewer experimental data for its verification. This equation may be derived in the following manner. Making use of the analogy between mass transfer of fluid in a porous medium and electrical conductivity through the fluid in the same medium, we can postulate a hydraulic formation resistivity factor analogous to an electrical formation resistivity factor. From Poiseuille&apos;s Law the resistivity to flow in a tube of radius R is of the form 8u/R², where is the viscosity of the fluid. Similarly7 the resistivity to flow in a porous medium of the same dimensions as the tube is given by D&apos;Arcy&apos;s Law as where k is the permeability of the medium. The hydraulic formation resistivity factor, Ff, is thus the quotient of these two resistivities, or: But permeability is defined by the KO-zeny equation as: where: r is the average pore radius of the porous medium, L. is the average tortuous length of the average pore, + is the porosity, and L is the bed length. This gives Fr as a function of the (La/L) .-.-.tortuosity ratio and porosity, or in explicit form: where: T = (La/L)&apos;, and N is the number of pores of radius, r, which will be found in any cross sectional area, x R&apos;. That is, N = R²/r². It will be clear from the foregoing considerations that the hydraulic formation fat. tor should be dependent on the value of R which in every case must be arbitrarily selected. By analogy, the hydrauiic formation factor, Fcf, characterizing the porous medium at Sw<1,will be given by: R² NT. where ke is the effective wetting liquid permeability obtaining at Sw<l, and Te is the square of the (Las/L) ratio defined by Thornton. Therefore, the hydraulic resistivity index, If, is: However, Thrnton gives I as: and it follows that: Equation 2, when checked against the data of wyckoff and Botset² and some of the Morse et al data³, gives comparisons as shown at the bottom of this page. Computations based on Leverett&apos;s data, quoted by Thorntaon, gives computed krw values somewhat lower than the experimental values. Moreover, other instances can be cited where we find that neither Equation 1 nor Equa tion 2 is checked by experimental data. The work of Botset&apos; on the Nichols Buff sandstone and Morse et a1 on oil wetted Bradford sandstone are such instances. A reason for these discrepancies may lie in the fact that if both Equations 1 and 2 are presumed always to give accurate values for krw, it follows that PC = Pd/Sw". Such an expression, it is well known, is too simple to describe accurately the capillary pressure behavior of all porous media. However, it is believed that a particular advantage resides on the use of Equation 2, since it is not dependent for its utility on a knowledge of the capillary pressures obtaining in dynamic flow svsterns. No practical technique for measuring the capillary pressures characterizing the fluid distributions in dynamic flow systems has yet been proposed. Acknowledgment is given to Dr. Paul D. Foote, executive vice-president of the Gulf Research and Development Company, for permission to publish this note. 1. Owen F. Thornton, "A Note on the Valuation of Relative Permeability," J. Pet. Tech., 1:7, Section 1, July, 1949. 2. R. D. Wyckoff arid H. G. Botset, "The Flow of Gas-Liquid Mixtures through Porous Media," Physics, 7:325-345, 1936. 3. R. A. Morse, P: L. Terwilliger, .and S. T. Yuster, "Relative Permeability Measurements of Small Core Samples," Oil and Gas J., 46:109-125, Aug. 23, 1947. 4. H. G. Botset, "Flow of Gas-Liquid Mixtures Through Consolidated Sand," Trans. AIME, 136:91, 1940.

Jan 1, 1949

By S. J. Salat, E. E. Burton

The new Inspiration copper smelter, which introduced unique technological innovations to the copper industry, required a plant material handling system to match. The system has been designed to convey such diverse bulk materials as copper concentrates, copper precipitates, lime, limestone, silica, flue dust, and revert materials. The moisture content in the materials varies from bone dry to a maximum of 25%. Since the summer of I974 when the smelter went into operation, the material handling system ha provided satisfactory and dependable services.

Jan 1, 1981

The Board of Directors has authorized the following offers of sets of back volumes of the Transactions, at considerably reduced prices, to Members, Libraries, and Scientific Societies Per Set. I. Five volumes, bound in half-morocco, from No. 36 (1906) to No. 40 (1910), . $20 II. Ten volumes, bound in half-morocco, from No. 31 (1902) to No. 40 (1910), including Mexican Volume, 35 III. Twenty volumes, bound in half-morocco, from No. 21 (1893) to No. 40 (1910), 50

Jan 4, 1913

Organization. Place Date 1915 American Institute of Mining Engineers New York, N. Y. Feb.18-21 National Society for Promotion of Industrial Educa- tion New York, N. Y. Feb. American Institute of Architects.... Washington, D. C. April American Iron and Steel Institute New York, N. I? May New York Electrical Society: New York, N.. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept.9-13 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic City, N. J. Sept.

Jan 2, 1918

By Willard S. Morse

Referring to Mr. Rickard&apos;s paper on " The Limitations of the Gold Stamp-Mill" (Trans., xxiii., 137), and the discussions that have followed, and without entering into any controversy as to the relative merits of the " California " and " Colorado " types of stamp-mills, I wish to give the results obtained on ores from Lynx Creek district, near Prescott, Arizona, with a stampmill of the Colorado, or, more precisely, the Gilpin county, Colo., type. The mines of the district have been worked for nearly thirty

Jan 1, 1896

By Tayler H. Bingham

Personal consumption expenditures represent roughly two-thirds of total of GNP. While these expenditures directly account for only a small portion of total natural resource consumption, they account for a significant proportion indirectly. The reason is that all economic activity can be shown to be interrelated and that the intermediate production sectors, which are the primary users of natural resources, represent the interindustry transactions necessary to produce all final goods, including consumer goods. This paper provides a discussion of the methodology and quantitative estimates in physical units of the interrelationships between 15 major nonenergy resources and 6 energy resources and 477 personal consumption expenditure items.

Jan 1, 1977

By R. A. Blake

Measurements of the quantity of xanthate abstracted from mineral surfaces and put into solution by an increase in the hydroxyl ion concentration were made. A residual xanthate concentration of 59.6 ppm was found in one case at a pH of 11.8. The abstracted xanthate is capable of acting as a collector on fresh mineral surfaces under proper conditions. It was learned that as the hydroxyl ion increased and the xanthate abstracted, the coarse particles lose their floatability first. A volume weight relationship based on percentage coverage was established and seems to offer a reasonable explanation of the cause of observed results.

Jan 1, 1973

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to &apos;85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By R. S. Rickard, H. D. Peterson, M. C. Fuerstenau, J. D. Miller

The flotation characteristics of the oxide copper minerals, malachite, azurite, and cuprite, have not presented the difficulty for concentration as have those of the copper silicate, chrysocolla. The copper carbonates and oxides respond reasonably well to flotation with conventional collectors, whereas chrysocolla will not respond to flotation with fatty acids or xanthates under normal flotation conditions. In this view then, other reagents will have to be devised to function as collectors for chrysocolla. The most obvious general class of reagents for this purpose would seem to be the organic copper chelating compounds. The utility of chelating agents as collectors in flotation systems has already been demonstrated.1-6

Jan 4, 1966