Search Documents

By J. W. Snavely

A practical mathematical treatment is presented for the determination and control of conveyor belt acceleration, particularly for conditions of starting where vertical curves are involved. A typical sample problem is analyzed, with required calculations, to clarify the procedure. THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for .each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, 'which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. 1 affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1953

By J. B. Hiskey, G. Ramadorai

This paper presents the kinetics of leaching pure wulfenite (PbMoO,) with sodium sulfide solutions. Wulfenite dissolves in the presence of sulfide ion according to the following reaction: PbMoO , + S= PbS + MOO;. Synthetic galena is formed and molybdenum is released to solution as molybdate ion. The reaction follows the shrinking core model and the leaching mechanism involves mixed kinetics where both diffusion and chemical reaction are rate controlling. Molybdenum extraction is explained in terms of temperature, particle size, and sodium sulfide concentration.

Jan 1, 1977

By A. W. Fahrenwald

THE function of the classifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred tows "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particular method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted.

Jan 1, 1930

By C. A. Schempp

STUDY of the adaptability of Tintic Standard ores to concentration dates back to somewhat before January, 1921, when the chloridizing mill at Harold, Utah, was put into operation. The operation of this mill has been fully covered in the TRANSACTIONS (Vol. 73). The process consisted essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid; precipitation of silver on sponge copper, and of copper and lead on tin-plate cuttings. This mill was built to treat the low grade siliceous ores having an average content of

Jan 1, 1933

By D. R. THOMAS

GENERALLY speaking, the production of other metals in Mexico fluctuates with that of silver. The first commercial discovery of mineral was in Taxco, Guerrero, in 1552. Five years later, the patio process was introduced at Pachuca, by Bartolome de Medina. In 1884, the main line of the Mexican Central R. R. was completed and a few years later, the National railway. In 1907, the patio process, after 350 years of successful operation, was replaced by cyanidation. Soon after the completion of the railroads, smelters were built at various points and provided means of treating ores that could not be treated by any of the processes existing at that time, such as patio, lixiviation, or pan amalgamation. As a result, a number of mines were developed along the railroads and even far \ out in the mountains. In order to facilitate the shipment of this ore to the smelters, purchasing agencies were established, which for a time were very profitable; most of these agencies are now permanently closed.

Jan 1, 1921

By Harold A. Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand- book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By J. W. Rutter, K. T. Aust

Observations are presented of the formation of annealing twins during the growth of a recrystallized grain into a striated, melt-grown crystal of high-purity lead. The formation of an annealing twin resulted in replacement of the original migrating boundary by a large-angle grain boundary of the caincidence-site type or by a near-twin boundary. The results support the Fullman-Fisher theory of annealing twins and demonstrate the usefulness of the coincidence-site model. FULLMAN and Fisher1 have advanced the following theory to account for the formation of annealing twins during grain growth. Whenever a grain A grows into a matrix of grains S1 and S2, a twin A' of grain A may form, as shown in Fig. 1, if the following energetic condition is satisfied: where "E" and "a" refer to the specific interfacial free energy and the area, respectively, of the boundaries indicated by the subscripts. In effect, the twinned grain will persist when the energy of the boundary between the twin(A') and the matrix grain (S, or S,) is less than that of the boundary between the original growing grain (A) and the matrix grain by an amount which exceeds the energy of the coherent twin boundary between A and A'. Experimental observations on the changes in grain boundary free energy accompanying the formation of twins1 are in agreement with the theory outlined in Eq.[l]. Direct observations of the formation of annealing twins at moving grain corners1"3 and the depend-

Jan 1, 1961

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments, and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union, and the United States are summarized Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1980

By C. L. HUSTON

MY ANCESTRAL connection with the manufacture of boiler plate runs back through four generations, and my personal acquaintance with the practice reaches back to the time, in my ,boy- .hood days, when iron plates' were made in a mill operated entirely by water power. -The mill originally was driven by an old-fashioned "'breast" water wheel 20 ft. in diameter and with a20-ft. face, geared direct to the roll train. When the mill slowed up and there was danger of its stalling, the men would jump upon the rim and help the wheel around with their weight, to prevent a "sticker." Later, as large plates were called for, a flywheel was set out of line so that it could' be speeded up by gears from the water wheel and connected back again,. by reducing- gears, to the roll train. The flywheel, with its cast-iron rim and wooden spokes, made 90 r.p.m. and the roll train 45 r.p.m. In 1870, our company installed our first steam-driven plate mill two-high rolls, 84 in. long. In these early mills the hot metal was manipulated by hand.

Jan 1, 1920

By KING HAMILTON GRAYSON

IRON and steel were the only basic industries in the Soviet Republic in 1928 that lagged behind the pre-war production on a comparative basis. This was due to the almost complete obliteration of all industrial units manufacturing iron and steel products during the Revolution, which resulted in the production of 1921 being only 4 per cent of that of 1913. By the end of 1927 the production of pig iron had reached a point equal to 70.5, per cent of 1913; steel was 84 per cent ; and rolled iron was 78 per cent. According to the. planned program of the Supreme Economic Council, the pre-war level of the iron and steel industry was to have been reached and exceeded during 1929-30. The production of the entire period from 1917 to 1928 in comparison with 1913, is shown in the following table

Jan 1, 1929

By A. L. Engel

IN the treatment of complex ores by flotation, one of the most important steps is conditioning the feed. Conditioning primarily consists of the addition, in the grinding circuit, of an alkaline reagent, for example sodium carbonate, which neutralizes any acidity of ore and mill water, counteracts the effect of 'harmful soluble salts, disperses colloids, and provides the necessary alkalinity for the best metallurgical results. The several minerals of the ore should be put in such condition that they may be floated or rejected as desired, through the action of further reagents thereafter used.

Jan 1, 1932

Jan 1, 1935

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article1 describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation.

Jan 2, 1953

Dubbed "Freeport's Mission Impossible" by the trade press, the company's Ertsberg mine in West Irian nevertheless shipped its first concentrates in December 1972, ahead of schedule. This is a new and great chapter in the history of Freeport Minerals Co. and its contractors. Exploration and construction were only possible by moving equipment and supplies by helicopters. This work was carried out by Petroleum Helicopters, Inc., of Lafayette, La. At the peak of operations six machines were in service manned by 11 pilots and supported by 10 mechanics. During the month of August, with work in full swing 1,604 tons were moved, including 3 DC-6 tractors requiring 18 trips each; flying hours for the month were 636.

Jan 1, 1973

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort.

Jan 5, 1951

By D. R. Mitchell

FOR the second consecutive year, attendance at the Coal Division sessions far exceeded exoectations. Those in charge were continually faced with problems of finding seats and space for attending members. 115 seats were set - II~ for the annual luncheon meeting of the Division and approximately 175 members showed un. Since the hotel management would not serve more than the 115 it meant that 60 members were forced to eat elsewhere. This created hard feelings with some members. How- ever, officials of the Division were not able to obtain in advance any indication of this overflow crowd, but are suggesting to the New York Office that some means other than ticket sales be adopted to obtain an estimate of Division luncheon and dinner attendance. Members could be circularized prior to he meeting or they could be checked when registering as to the events they expect to attend. Under the inspiring leadership of Cadwallader Evans, Jr., Chairman, the Coal Division had a phenomenal growth during the year. Reporting at the luncheon meeting, Newel1 Alford stated that approximately 190 new members had been obtained. A few more years of continuing increase at this rate will make the Coal Division one of the largest Divisions in the Institute.

Jan 1, 1944

By Shiou-Chuan Sun

Most previous work on sedimentation of coal1 and mineral2,3 suspensions has been conducted in graduated 1-liter glass cylinders of 6-cm diam. With this type of large container it is often difficult to see through the suspension and tedious to perform a large number of tests. Furthermore, the heavy glass walls and the graduation lines of glass cylinders cause internal and stray reflections, respectively. To obviate these difficulties, an Atlab Emulsion Viewer from Arthur H. Thomas Co. was adopted as an alternative apparatus. Equipment: The viewer,4 shown in Fig. 1, consists of: 1) a stainless steel frame rack holding 21 flat-bottom Nessler tubes or an ungraduated replica 1.64 cm ID and 1.80 cm OD, 2) a movable masked 150-w lumaline lamp behind the tubes, and 3) a scaled glass panel with 100 vertical divisions in front of the tubes. The tubes are snugly held by springs in slots formed by spacer bars, which also serve as shields to eliminate stray light. The lumaline lamp is mounted behind a slit in a movable housing so that it can be positioned behind the suspension to be examined. The lowest or 100-division line on the front glass plate is leveled with the upper side of the bottom of all tubes. The scaled portion of each tube, roughly 19 cm high and 40 ml in volume, is used to study coal and mineral suspensions.

Jan 1, 1959

By E. P. Klier, V. Weiss

IN studies of the X-ray diffraction line geometry of iron with chromium radiation using techniques aimed at minimizing the background intensity, Kp and Ka emission satellites* were resolved with three techniques. These satellite lines are present with sufficient intensity to lead potentially to erroneous structure analysis, if not properly interpreted. The techniques used were: 1) film technique with un-filtered radiation and polycrystalline specimen, 2) film technique with unfiltered radiation and single crystal, and 3) counter technique with unfiltered radiation and single crystal. An example of results obtained with technique 1 is given in Fig. 1.

Jan 1, 1958

By Nev A. Gokcen

DISCREPANCIES and scattering in the equilibrium data on the reactions of hydrogen, and CO with dissolved oxygen in liquid iron are un- duly large. Available experimental results on the reduction of liquid ferrous oxide, i.e., wüs-tite, with hydrogen and CO are questionable, as pointed Out by Darken and Gurry'l Direct determinations of the solubility of oxygen in liquid iron are subject to errors which cannot be easily reduced by further experimental refinements, and therefore an accurate but indirect method is highly desirable. The purpose of this investigation was, therefore, 1)

Jan 1, 1957

By Irwin Roman

PART I. INTRODUCTION THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years, but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and. engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1931