Search Documents

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds ;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2 : I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium. some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17, 32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established .R3 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resinsmay serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Richard Paul Seelig

THE following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which may stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. EXPERIMENTAL APPROACH The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. In as much as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a compressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Al- though these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself,8 calls attention to the fact that the properties

Jan 1, 1947

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

THE solid nonmetallic inclusions that are present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and. this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general the term "nonmetallic inclusions" seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those that occur as a result of reactions taking place in the body of the molten or solidifying metal and (2) those that result from the mechanical incorporation of refractories or other materials with which the steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulphidea but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from the molten or solidifying steel may be caused by (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change in equilibrium constants as the steel cools to the freezing temperature, (4) decreased solubility with lower

Jan 1, 1944

By K. T. Aust

The occurrence of annealing twins in high-purity aluminum resulted in the formation of grain boundaries having orientation relationships which correspond to a high density of coincidence sites. The results provide support for the coincidence site model and indicate that large-angle coincidence boundaries have lower free energies than large-angle noncoincidence boundaries. Observations are presented concerning the coherent structure of twin interfaces in aluminum and the importance of inter-facial energy in preferred orientation. RECENT experiments1 have shown that when an annealing twin is formed during grain boundary migration in zone-refined lead, a large-angle random boundary is replaced at the growth front by a large-angle coincidence site boundary. The coincidence site orientation relationships obtained by twinning were of the type considered by Kronberg and Wilson,2 Frank,3 and Dunn.4 On the basis of the theory of annealing twins advanced by Fullman and Fisher,5 these observations indicate that the energy of a coincidence site boundary is less than the energy of a random boundary by an amount which exceeds the energy of the coherent twin boundary. This energy difference between the coincidence and random boundaries must be at least about 5 pct since the ratio of twin boundary energy to grain boundary energy in zone-refined lead is 0.05 * .014.6 Fullman7 has found that the twin boundary energy in aluminum is about 21 i 5 pct that of a large-angle grain boundary. A twin boundary energy as large as this would be expected to exclude the formation of many coincidence site grain boundaries, especially those which have a relatively low density of coin- cidence sites. Therefore, if the coincidence site model is a useful interpretation of certain large-angle boundaries, then it would be predicted that only coincidence boundaries which separate adjacent crystals with a relatively high density of coincidence sites may be obtained as a result of twinning in aluminum. The present experiments provided a means of testing this prediction since annealing twins occurred during the growth of recrystallized grains into striated, melt-grown single crystals of zone-refined aluminum. EXPERJMENTAL PROCEDURE A striated single crystal of zone-refined aluminum, about 1 cm sq and 37 cm in length, was obtained during zone melting of aluminum of 99.996 wt pct starting purity in a graphite boat under helium atmosphere.8 A molten zone of 2 to 3 cm in length, which was maintained by induction heating. was passed along the length of the bar for eleven passes at a rate of 0.9 mm per min. An additional final pass was given at a rate of 0.2 mm per min. The center portion of the zone-melted bar was characterized by an electrical resistivity ratio between room temperature and 4.2° K of 8000 to 9000. Single crystals of 1 to 2 cm in length were removed from the center section of the zone-refined bar and electrolytic ally polished in a 2:l solution of methyl alcohol and concentrated nitric acid. The specimens were then chemically polished in Alcoa R-5 solution. X-ray analysis of the single crystals indicated the presence of striations or lineage substructure having misorientations as high as 2 deg. New, recrystallized grains were introduced into each striated crystal by the technique of artificial nucleation and growth, previously described.9 During the growth of the recrystallized grains at 300' to 600°C in argon, it was sometimes found that a

Jan 1, 1962

By C. van der Poel, R. L. Chuoke P. van Meurs

When an initially planar interface between two im-ttitcihle liquids is displaced at constant rate, U, nor-mat to the front, instability will occur for all rates greater than a critical rate. U, given by provided the Fourier decomposition of the spatial pertmrbcrtiott or deformation of the moving displacetment front contains modes with wavelengths. A, greater than a critical wavelength, given by tit there expressions, p, p and k, with the subscripts I and 2 distinguishing the two 1iquids under consideration, are density, viscosity and effective pemeability coefficients respectively; g is the absolute value of the acceleration due to gravity; and cos (zz') is the direction cosit7e between the vertical carlesian coordinate z' (positive upward) and the z coordinate norma1 to the initially plane macroscopic interface taken positive in the direction from Liquid I to Liquid 2. U is the average volumetric velocity (injected volume of liquid pet. unit time per unit of area normal to Z) and is positive for Liquid I displacing Liquid 2, negative for the reversc displacement and r2 is an effective inter-fucial tension (for displacements between parrallel plates, t0= s the ordinary bulk interfacial tension). further, there is a wavelength of maximum instability given by For natural perturbations, this wavelength will preclotninate and characterize the form of the instability as a quasi-sinusoidal deformation, i.e., viscous fitzgers of peak-to-peak separatiotr, A,,. Comparison of experitient with theory rei'eals tltat these considerations are recsonably valid for displacements in hoth parallel plate chantzels and nnconsoli-clutt'd glass ptnvder packs. These results are. tij particular interest for interpretation of data from laboratory experiments with regard to fielil applica/iotz.s. It is quite possible for A,, although st7zall relative to the large lateral dimension of the reservoir, to rxceed the greatr.st lateral extent of the lahoratory sample or model. If it does, frontal displace- ment occurs in the laboratory experiments, and oil INTRODUCTION Thc puposes of this paper are to present theoretical and experimental evidence for occurrence of macroscopic instabilities in displacement of one viscous fluid by another immiscible with it through a uniform porous medium and to compare available experimental data with some predictions of a theory of instability developed by the first author. The instabilities are referred to as macroscopic in the sense that spatially quasi-sinusoidal, growing fingers of the displacing liquid are formed, the width and peak-to-peak separation (wavelength) of which is large relative to a characteristic length of the particular permeable medium such as grain size. Visual models of two kinds have been used to obtain observations: displacement of oil by water-glycerine solutions through the flow channel formed by closely spaced parallel plates and displacement of oil by water with and without initial interstitial water through unconsolidated glass powder packs, employing the technique of matching indices of refraction. In all cases we have observed macroscopic instabilities or fingers under conditions predicted by the theory to be favorable for their occurrence. The phenomenon discussed here is not the production of streamers due to gross inhomogeneities such as permeability stratification of the porous medium. It is our object to show, on the contrary, that a quantitative prediction of finger spacing is possible in a porous medium known to be macroscopically homogeneous and isotropic throughout. The importance of the phenomenon in its influence on the configuration of oil and water with respect to oil production behavior was noted earlier by Engel-berts and Klinkenberg' who coined the term "viscous fingering". THEORY Necessary and Sufficient Conditions ior Instability anc Initial Kinematics There are several levels of increasing complexity in the theoretical description of instabiIity of fluid displacements in permeable media. Of these, the simplest description, ;tdapted to low permeability systems, is selected for presentation.' More inclusivc tlescriptions are reserved for separate publication.

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By John W. Cahn, David A. Karlyn, Morris Cohen

The massive B(bcc) — am (fcc) transformation in Cu-Zn alloys has been studied isothermally by pulse-heating the retained ß phase from room temperature to the reaction temperatures. The transformation is found to occur only in the single-phase a region of the equilibrium diagram. The massive growth rate is of the order of 1 cm per sec and is constant at each temperature, usually after a delay time of some milliseconds. The delay time depends on the reaction temperature in C-curve fashion, while the growth rate increases monotonically with temperature over the single-phase range. The absence of isothermal massive transformation in the two-phase region does not arise from slow growth rates at such temperatures, but because the reaction cannot get started there. It is proposed that the massive transjormation initiates at small preexisting a particles which have rejected zinc into the surrounding 0 matrix. Only within the single-phase region can these particles consume the excess zinc during diffusion-controlled growth and thereby accelerate to the steady-state massive growth rate. The onset of massive growth marks the end of the delay time, and the growth rate then becomes interface-controlled. These isothermal transformation characteristics explain why the usual composition range for massive-kinetic studies by quenching is so limited. The same principles can be extended to more complex alloy systems by recognizing that the single-phase region in which the massive transformation can occur may not be stable with respect to phases not participating in the reaction. MASSWE transformations are now recognized as a regular class of solid-state reactions involving no compositional change (like martensitic transformations) and no shear displacements (unlike martensitic transformations). The name was first coined by Greninger1 in 1939 to describe the coarse grains of fcc a solid solution generated via a fast reaction from the parent bcc 0 solid solution in Cu-A1 alloys. However, some 9 years earlier, phillips2 had already described a similar transformation in the Cu-Zn system. The fact that the massive a formed as a single phase during drastic quenching from the 0 region of the equilibrium diagram signified that compositional changes were precluded. and the reaction was presumed to take place as in a one-component polymorphic transition by nucleation and growth. Phillips also observed that the occurrence of the massive transformation in the Cu-Zn system was extremely sensitive to alloy composition. For example. in a Cu-37.3 at. pct Zn alloy. the ß — am (am = massive transformation product) reaction was found to predominate and was not suppressed by iced-brine quenching from the 0 region. whereas at compositions greater than 38.3 at. pct Zn the massive reaction did not appear at all. Knowledge concerning massive transformations has bee11 substantially enhanced over the years by Massalski and his coworkers; an excellent summary of his papers and the current understanding of this type of reaction has been published recently by Barrett and ~assalski." he massive transformation product grows in roughly nodular form. often with irregular boundaries but sometimes with almost planar interfaces. The latter may have simple crys-tallographic indices relative to the 0 matrix. or the indices may be complex just as in the case of mar-tensites.'1 Little is known about the existence of orientation relationships between the massive and parent phases. A striking feature of massive transformations is that the massive units start almost exclusively at grain boundaries of the parent phase and frequently propagate on a broad front across matrix grains and grain boundaries of various orientations. Because of the rapid growth rate, it is thought that the interface motion is controlled. not by long-range diffusion. but by thermally activated atom jumps across the transformation boundary.

Jan 1, 1970

By Lucien F. Trueb

The microstructure of explosion-bonded pairs of similar and dissimilar metals has been investigated by electron microscopy. A review of the specific problems encountered and the methods used for obtaining surface replicas and thin-film transmission specimens of the bond interface is given. The bond area is mainly characterized by continuous and practically diffusionless metallurgical bonding. The very large shear stresses induced along the collision front of the plates being joined causes extreme grain elongation and a symmetrical pattern of subgrains in the bonding direction. The bond zone is also characterized by a very high density of dislocations and pressure-induced twins. Localized heating occurring during the cladding process can result in partial re-crystallization or the formation of thin layers of molten material. The force of precisely controlled explosions causing a high-velocity impact between metal plates has been used for several years to achieve metallurgical bonding between an extremely wide variety of metals. This method essentially consists of accelerating a plate to high velocity toward a stationary plate by a detonating explosive. Since the restrictions to bonding are not those encountered with conventional nethods, it becomes possible to bond pairs of metals having widely different mechanical properties that are immiscible or form brittle intermetallic compounds. Many applications of such composite metals are found in the field of corrosion protection as well as numerous other fields; for example, explosion bonding is being applied for fabricating the materials used by the United States Mint in the new sandwich-type coins. The primary condition for establishing a metallurgical bond is that absolutely clean metal surfaces be brought together. Any metal exposed to the atmosphere is covered with oxides, adsorbed gases, and other contaminants; even a very forceful impact of two such surfaces is not sufficient for bonding. Cowan and Holtz-man,"' who reviewed the dynamics of colliding plates in detail, showed that in order to achieve a good bond the explosion conditions must be chosen in such a way that the plate collision velocity is less than the sonic velocity, in which case no oblique shock waves are attached to the collision front. A pressure wave is then generated ahead of the collision line, and the material forming the colliding surface of each of the plates flows forward and is ejected in the form of a spray, the so-called jet. The dynamic elastic limit of the metals must be exceeded so that there is sufficient plastic deformation. At the point where the jet formed by the junction of the inner surface layers of both plates separates from the combined plates, the material experi- ences a very high shearing strain and the pressure can reach several hundred kilobars. This process strongly influences the microstructure of the bond zone as will be seen later. Behind the collision front, uncontami-nated layers of internal material are brought together under high pressure and are thus metallurgically bonded. I) STRUCTURE OF EXPLOSION BONDS The different types of explosion bonds that can be obtained depend on the explosion conditions, and have been investigated by Cowan and Holtzman,1'2 Holtzman,3 Klein; Bahrani and crossland,' and Buck and Horn-bogen. The preferred kind for practical applications is the so-called wavy bond, typical examples of which are given in Fig. 1 showing light micrographs of various metal-to-metal interfaces. In forming this type-- of bond the collision energy is mainly expended in jetting, the formation of waves, and localized melting. Beyond the crest of the waves, eddy-shaped areas are observed in which the two metals are mixed in a complex pattern of streaks. Cowan and Holtzmanl first proposed that this wavy pattern is analogous to periodic eddy shedding in the flow of a viscous fluid around an obstacle (Von Karman's eddy street). The mass of metal ahead of the stagnation point, which is associated with the jet and has forward momentum, plays the role of an obstacle and the eddies created in the flow of solid metal around the stagnation point are preserved in the final clad specimen. This idea has been reviewed more recently by Klein4 and the variables involved in the wave formation have been discussed in some detail by Bahrani and crosslands and Buck and Hornbogen.6 Several studies of the structure of explosion bonds by light metallography have already been published.1-6 Aside from the waviness and the eddies which were mentioned above, the most striking characteristic of the area in the vicinity of the bond interface is a very considerable longitudinal grain deformation which appears to be strongest at the metal-to-metal boundary and dies out as one moves away from it. Large twins are often observed within the deformed grains, and molten areas are found in the center of the eddy-shaped structures situated beyond the crest of the waves. The large hydrostatic pressures and shear stresses occurring at the interface modify the mechanical and chemical properties of the bond zone. Increases in hardness in this area have been reported by various authors.396 The defects along the interface can also cause a local increase of the chemical reactivity and thus might be expected to boost the etching rate. However, the effects of this preferential etching cannot be observed by light microscopy due to its inherently limited resolution power. The same limitation precludes the observation of morphological features directly along the bond interface as well as the interface itself. Furthermore, no information can be gained by light-

Jan 1, 1969

By Jack Green

Within three major tectonic time frames of earth history: Microplate (±3.8 - ±2.6 billion years), intraplate (±2.6 - ±1.3 b.y.), and macroplate (=1.3 b.y. - present), precious - metal deposits are confined to specific structural, depositional and physico-chemical environments. Precambrian primary gold deposits are localized in two microplate greenstone episodes (±3.7 and ±2.7 b.y.); secondary gold in Witwatersrand placers (±2.6 b.y.). Precambrian primary platinum group metals are in anorthositic facies of layered mafic intrusions (±2.8, ±1.8 and ±1.0 b.y.). Most radioisotope mineral dates cluster - at these times and are coincident with inflections on polar wandering curves. These coincidences may reflect episodicity in lunar tidal disruptions and global deceleration effects in crust and outer core during micro- and intra- plate phases. Macroplate tectonics and an oxygenated atmosphere created favorable conditions for strata-hosted and plate suture gold and silver deposits. "Black smokers" at constructive plate margins and calc-alkalic calderas at destructive plate margins are loci for hydrothermal gold and silver.

Jan 1, 1984

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By M. N. Shetty, A. C. D. Chaklader

RECENTLY, it has been demonstrated that a considerable densification and interparticle bonding can be achieved if a pressure is applied to a powder compact while the material of the compact is undergoing either a decomposition reaction' or a polymorphic transformation.' The term "reactive hot pressing" has been coined to identify this process in which a phase change is combined with pressure to achieve interparticle bonding. This process is based on a principle which postulates that there is an enhanced reactivity and mobility of the molecular species at the phase-transformation temperature and this effect is utilized for interparticle bonding in powder compacts. This note summarizes the results obtained in an attempt to utilize this technique to produce ceramic-metal composites. In this case, a decomposition reaction of a compound (which after decomposition yielded an oxide) was used to achieve interparticle bonding in ceramic-metal composites. The reactive hot pressing was carried out in a Phillips induction heating unit, using either a graphite or a high-temperature steel die which functioned as both the susceptor and the hot-pressing component. The die was heated to the desired temperature in a helium atmosphere. All cermets produced by this technique were based on alumina as the ceramic phase. Different metal phases such as iron, copper, and chromium were used to study the effect of varying the metal phase on the properties of the composite. a Mono-hydrate (Boehmite) was mixed with different proportions of metal powders (-325 mesh) in dry condition in a mortar and pestle. No special precautions were taken for proper mixing. The mixtures were then compacted into a cylindrical form having an approximate dimension of 1 cm in diameter and 1 cm in height. For this compaction an ordinary

Jan 1, 1965

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well's results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. 'This means that careful measurements of surges occurring in actual field operations must be made.

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By AIME AIME

SECOND only to the February Annual Meeting of the Institute are the Regional and Divisional meetings held in the fall of each year. Six such gatherings are scheduled in the next the months, with something likely to interest every member of the Institute. A brief résumé of the programs follows. Regional Meeting Vancouver T HE regional meeting of the Institute will be held at Vancouver, Sept. 13 to 20, in conjunction with the annual western meeting of the Canadian Institute of Mining and Metallurgy. The pro gram appeared on page 350 of MINING AND METALLURGY for July and-proof of careful preparation-a month later re- quires no correction and little elaboration. On the technical side there are few changes. A new item on the Wednesday morning program is the paper, "Investigation of Residential-type Stokers," by H. F. Yancey, supervising engineer, Northwest Experiment Station. U. S. Bureau of Mines, Seattle. As to entertainment the meeting is taking on some most pleasurable aspects. Two notable excursions have been arranged.

Jan 1, 1937