Search Documents

By Peter G. Groer

Several methods1-3 are being used to determine the WL and individual Rn-daughter concentrations in uranium mine atmospheres. The best of these methods is the one given in Ref. 3. According to this method, the WL and the Rn-daughter concentrations are determined from the total a-counts observed during three consecutive time intervals. Its only disadvantage lies in the fact that rather involved calculations are necessary to convert the observed counts into WL or pCi/l (picocuries per liter). There are, however, counting intervals that give simple weighting coefficients for the observed counts. This fact makes it possible to convert from a-counts to WL or pCi/l with the aid of a graph. After some trial runs on a computer the following equations emerged as the basis for the most practical procedure: [ ] NA, N.., and & stand for the number of RaA, RaB, and RaC atoms per liter of air. C(t1,t2) denotes the counts observed from time t. to time t2 (in minutes) after the end of the 5-min sampling period. E is the detector efficiency and V is the flow rate in liters per minute. With an accuracy loss of less than -5% one finds from [Eq. 1] by adding the corresponding terms: If the WL would have been calculated according to [Eq. 2] instead of using the graph, the result would have been 0.31. Since the values used for C's under [Eq. 3] represent the exact number of counts from a Rn-daughter mixture in equilibrium with 100/3 pCi of Rn the exact WL of this mixture can be calculated easily. The exact value is: [ ] This shows that the method is quite accurate for the 0.3 WL domain. The precision of the method excluding errors made in reading the graph can be estimated with the help of the following formula: [ ]

Jan 1, 1974

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Paul M. Musgrove, Larry S. Diaz

Recent tests conducted at Inspiration Consolidated Copper Co. examined some aspects of the value of a continuous measurement of particle size to the operation and control of a mill grinding circuit. Inspiration's control objectives and kinds of control systems developed in recent years to attain these objectives are outlined. A description is given of the arrangement of the test circuit at Inspiration and also of the systems used to measure particle size of the cyclone overflow product in these tests. Use of on-line size measurement for the analysis and improvement of grinding circuit performance is illustrated by relating how two important relationships were detected. Finally, the performance of a particle-size-based control system is described, including preliminary conclusions as to increased productivity.

Jan 1, 1974

By F. L. Fayers, J. W. Sheldon

It has been a matter of concern to the petroleum industry to determine what effect the capillary term has on saturation profiles, since these profiles determine ultimate economic oil recovery. In their original solution of the non-capillary two-phase flow problem, Buckley and Leverett&apos; showed that solutions of the two-phase flow equations became multiple-valued in saturation. Since it is physically unrealistic for saturation to have more than one value at a given position, Buckley and Leverett resolved this difficulty by introducing a saturation discontinuity or "shock". They evaluated the strength and position of the shock from material balance considerations. Recently Sheldon, Zondek and Cardwell&apos; have demonstrated that the method of characteristics can be used to solve this and related problems. Owing to capillarity it is physically unlikely that saturation shocks occur in an oil reservoir. Buckley and Leverett suggested that the effects of interfacial tensions should be included in the fluid flow equations, if the solutions are to give continuous single-valued saturation distributions. An analogy to this problem is encountered in the theory of wpersonic compressible flow where the introduction of the viscous term eliminates shock behavior. However, the mathematical form of the capillary term in the porous medium fluid flow equations differs from the viscosity term in the Navier-Stokes equation. This paper demons~rates that capillarity does eliminate the triple-valued behavior and indicates the magnitude of capillary and gravity effects on the saturation profile for a variety of systems. DERIVATION OF LAGRANGIAN AND EULERIAN FORMS OF THE DISPLACEMENT EQUATION The equations representing capillary, two-phase flow are given by applying Darcy&apos;s law and a material balance condition for each phase. The familiar Darcy and material balance equations are as follows. ^U*^0......<3, ^^r=°......c« S is the saturation of the water phase, and B the inclination of the porous medium. Pressures in the oil and water phases differ by the capillary pressure associated with the interfacial tensions, P.-P.=pAS)..........(5) where p, is determined experimentally. The porous medium is said to be oil-wet if P, > Po and water-wet if P, < Po. If the fluids are incompressible and the total volumetric flow rate, q, is constant, then v, f v,, = q...........(6) By eliminating P.. /»,, and v, from Eqs. 1, 2, 5 and 6 it follows that It is convenient to normalize the variables in the problem after the manner of Handy and Hadley% so that Eqs. 3 and 7 become where j,, = —, the fractional flow of water; (F, is a capillary pressure normalizing constant.) Substitution of Eq. 9 into Eq. 8 gives In this partial differential equation for an initial value

By Eric R. Jette, Earl S. Greiner

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. &apos;This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,&apos; who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. &apos;This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,&apos; who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government&apos;s map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council&apos;s recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By P. V. Brough, K. B. Gillaspie

DECISION to build a mill at the Bayard property was made in May 1942. Western-Knapp Engineering Co., of San Francisco, assisted by engineers of U. S. Smelting, handled the design and construction. Much of the milling equipment was moved from the Company&apos;s mill at Goldroad, Ariz. Wartime restrictions necessitated wood construction and paper sheathing except for structures adjacent to the Bullfrog shaft. Construction started in September 1942 and milling in March 1943. Bayard ores are processed in a single-ection mill. About half of the ore treated during the past year was hoisted through the Bullfrog shaft and the rest was trucked from other shafts. Coarse storage includes four bins, two of 120 tons each for Bullfrog ores and two of 85 to 120 tons each, served by a truck ramp. The low capacity figure refers to

Jan 1, 1948

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By Carl L. Shapiro, Jerome and Strauss

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Jerome and Strauss, Carl L. Shapiro

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By J. Menashi, D. A. Douglas, A. S. Rappas

Aqueous solutions of Na2Cr04 are reduced with CO to produce hydrous Cr2O3 and NaHCO3/Na2CO3. CH3OH, HCOO- and HCHO in the presence of CO2 also reduce Cr(VI) and yield similar products. It is shown that the rate of Cr(VI) reduction can be represented by the expression -d [Cr(VI) ]/dt = k[Cr(VI)]0.5[R], where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mol (43,000 Btu per lb mol). Rapid reduction rates are attained at temperatures in excess of 220°C (428°F). With these three reductants, a green acid-insoluble readily filterable hydrous Cr203, is formed. With HCHO, significant reduction of Cr(VI) occurs at about 80° to 100° C (176° to 212° F). The product is an acid-soluble violet modification of hydrous Cr203. Solutions of Na2CrO4 contaminated with Mo(VI) and W(VI) can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels.

Jan 1, 1986

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-&apos; the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By A. E. Powers, J. F. Libsch

THE simultaneous influence of time and temperature upon the tempering process in steel is well known. Hollomon and Jaffe¹ have expressed the effect of time and temperature upon the progress of tempering by a single parameter, T (c + log t); where T is the absolute temperature; t, the tempering time; and c, a constant characteristic of the steel and treatment. It was found that when hardness data for plain carbon and low alloy steels were plotted vs. this parameter, a master tempering curve was obtained which satisfied all the data for a given steel and a given hardening treatment. Roberts, Grobe, and Moersch² successfully applied the tempering parameter to various tool steels, including high speed steel for tempering times ranging from 6 min to 100 hr. The influence of tempering time and temperature upon the physical properties of high speed steel has also been extensively investigated.&apos;" Recently, the use of induction heating for very rapid tempering treatments has received attention. The authors% have shown that tempering treatments of only a few seconds duration may be successfully applied to plain carbon and low alloy steel. However, the influence of such short tempering treatments in high speed steel has not been explored. Since high speed steel is a highly alloyed steel exhibiting physical reactions during tempering that are often relatively slow and large in magnitude, it is an interesting steel for the study of tempering reactions. It was the purpose of the present investigation, therefore, to study the early progress of reactions leading to secondary hardness in high speed steel, type 6-5-4-2, and to determine if induction-tempering treatments of a few seconds duration are able to produce results equal to those of more conventional long-time tempering cycles. Experimental Details The chemical compositions for two different heats of W-Mo high speed steel used in this study are given in Table I. Table II summarizes the heat treatment given various groups of specimens cut 21/2 in. long and centerless ground to ¼ in. diam. Hardening treatments consisted of preheating to 1600°F (870°C) for V2 hr and then oil quenching from 2250°F (1230°C). Heat I was subjected to the high temperature in a salt bath for 3 min, while specimens of heat II were austenitized in a carbon-block muffle furnace for 10 min. Specimens of series E were immediately refrigerated to — 318°F (— 195°C) in liquid nitrogen following the hardening treatment to transform the major portion of the retained aus-tenite. Specimens of series F and G were subzero cooled to — 100°F (-75°C) in a dry ice-alcohol mixture. Induction tempering was performed with a Lepel high frequency converter operating at a frequency of approximately 300,000 cycles per sec. Heating cycles were controlled and recorded for each specimen using a chromel-alumel thermocouple, percussion welded to the surface of the specimen, and a modified high speed instrument with a timer previously used and described.&apos; Temperature oscillation of the specimens, while being held at the tempering temperature, was ± 15°F (8°C). Tempering Treatments: After hardening, specimens were tempered between 900" and 1500°F (480" and 815°C) to study the progress of retained austenite decomposition and secondary hardening. The specimens tempered in salt for 1 hr (series C, G, and I) were considered to represent conventional treatment and are used for comparison with rapid tempering treatments. Several induction-tempering cycles were employed: 1—flash tempering, i.e., induction heating to the tempering temperature and immediately cooling (series A, E, and F); 2—induction heating for 60 sec at temperature (series B); and 3—double-induction tempering by two successive heating and cooling cycles (series D). All specimens tempered by induction were heated at an initial rate of 450°F (250°C) per sec except those of series E, which were heated at an initial rate of 1300 °F

Jan 1, 1952

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892 H M HOWE 1893 JOHN FRITZ 1894 J D WEEKD 1895

Jan 1, 1923

By D. K. Deardorff, Haruo Kato

D. K. Deardorff and Haruo Kato (U. S. Bureau of Mines)—We wish to refute the 1875" 20°C value that Giessen, et al., report as the transformation temperature of hafnium. Although these authors state that their work along this line will be reported later, we can&apos;t leave their value undiscussed, for we believe it to be 125°C too high. Our value of 1750° 20°C, which the authors mention, has been substantiated in our laboratories by the use of three other methods. The first method of substantiation was by heating and cooling curves using a hafnium/tungsten thermocouple, the couple having first been calibrated against a t/Pt-10 pct Rh couple. The second method was by quenching and metallography of dilute Hf-Ta alloys. The third cussion, it may be pointed out that the observations of Rogers referred to large unidirectional strains where the internal cracks or voids appeared only after a strain of 32 pct or more. On the contrary the internal fissures observed, as a result of fatigue cycling, occurred for a total extension of some 5 pct and furthermore followed the directions of the slip zones. Finally, it is not our contention, as implied in Dr. Alden&apos;s last paragraph, that the tensile stress is an important factor in crack propagation. Indeed, in connection with the reference to the companion report, special note is made of the fact that "Deformation was apparently concentrated in grains which have a slip plane nearly perpendicular to the specimen axis and thus near the plane of maximum applied shear." This dependence of the growth of fissures on the orientation of the slip planes with respect to the direction of maximum applied shear is clearly shown in work on the torsional cycling of single crystals which has been submitted for publication. method was by heating and cooling curves with W/W-26 pct Re thermocouple. Counting the original resistometric method, four different methods have yielded 1750" 20°C as the transformation temperature of hafnium. All our work on determination of the hafnium transformation temperature has shown that the specimen under test must be quickly heated to and through the transformation temperature if the lowest possible transformation value is to be determined; otherwise a higher value not representative of pure hafnium will result. Speed was emphasized in all methods. In our resistometric work the corresponding voltage, amperage, and temperature readings were taken quickly and the transformation temperature was usually reached within 5 min total heating time. In the thermal analysis work involving Hf/W or W/W-26 pct Re thermocouples the transformation temperature was attained within three minutes total heating time, this time being less because the two variables were

Jan 1, 1963

By C. R. Keyes

Discussion of the paper of C. R. Keyes, presented at the Chattanooga meeting, October, 190S, Bulletin No. 26, February, 1909, pp. 119 to 166. E. R. BUCKLEY, Flat River, Mo. (communication to the Secretary*) :-Some statements in the paper of Mr. Keyes relative to the nature and formation of the Ozark lead- and zinc-deposits seem to me erroneous and misleading, and I respectfully present the following criticisms, placing Mr. Keyes&apos;s original statements in quotations. Referring to the Ozark dome: (P. 127.) "It is a region that has been repeatedly upraised and planed off, until in the middle portion the oldest known&apos; rocks only are exposed." Does he mean that the St. Francois mountains, which have always been considered as lying on the eastern flank of the Ozark dome, are the middle of the dome? Or does he mean that the Cambrian rocks of the generally-accepted middle are the oldest known rocks ? Certainly not the latter, and if the former, his idea of the middle of the dome is not in accord with that of others who are familiar with the region. (P. 138.) " . . . the ore-deposits are definitely associated with, or localized by, geologic structures of some kind that .produce in effect basins in which&apos; the underground waters are impounded, or their flow retarded." This statement does not appear to be altogether consistent with the facts, since the ore- bodies of the Joplin district, as the rule, occur in those parts of the Mississippian formation which have a tendency to accel¬erate the flow of ground-water rather than retard it. I might name the open, breeciated ground near Joplin, Webb City, and Oronogo as especially noteworthy illustrations. The ore-bodies, everywhere, occur in positions where there must have been a free and copious circulation of dilute lead- and zinc-solutions in the presence of reducing constituents. The inequalities in the distribution of the ore-deposits are

Oct 1, 1909

PAST AND PRESENT CHAIRMEN OF DIVISIONS Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSET 1919 " 1920 W. H. BASSETT 1921 " 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. B. ELLIOTT 1925 F. JULIUS FOHS 1926 P. D. MERICA 1927 11 JOHN. M. LOVEJOY 1928 S. SKOWRONSKI A. W. AMBROSE RALPH H. SWEETSER &apos; 1929 " J. B. UMPLEHY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN W. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. M. BECKET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNOR " 1934 J. L. CHRISTIE H. D. WILDE, JR. L. F. REINARTZ " T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H. DOLBEAR 1936 E. H. DIX, JR. HALLAN N. MARSH C. E. WILLIAMS EUGENE MCAULIFFE WILLIAM B. PLANK OLIVER BOWLES 1937 A. J. PHILLIPS M. ALBERTSON FRANCIS B. FOLEY J. B. MORROW " CHESTER A. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOMSON J. R. THOENEN 1939 R. H. LEACH W. H. GETS J. HUNTER NEAD C. A. GIBBONS " M. M. LEIGHTON 1940 E. M. Wise T. V. MOORE F. T. SISCO C. E. LA WALL W. R. CHEDSEY W. M. WEIGEL 1941 D. K. CRAMPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " PAUL M. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER

Jan 1, 1942