Search Documents

By Fred A. Hale

Owing to the large area included in the Yellow Pine mining district, and the varied nature of its mineral deposits, a detailed geological description of the district could be covered only in an extensive monograph. This paper is intended as a description of the most prominent geologic features only with special reference to those of economic importance. The first mention of the district was in 1903 by J. E. Spurr, who briefly describes the structural geology of the Spring Mountain range. In 1906, H. F. Bain2 briefly described the Potosi mine. James J. Hillla of the United States Geological Survey, visited the district for a brief period in 1912, the result of which is an excellent reconnaissance report, covering the district in some detail but necessarily with brevity. Since that time, articles covering special features of the district have appeared in the technical press, including some by the writer, and a notable description of the Boss mine, by Adolph Knopf,4 appeared in 1915. Development of the district during the past few years has progressed so rapidly and with so many notable discoveries, particularly with reference to the rare metals, that a further description at this time may prove of interest. The writer's acquaintance with the district is based on 7 years' continuous residence in the vicinity, beginning with the spring of 1910. A. Location and Topography The Yellow Pine mining district is situated in the southwestern portion of Clark County, Nevada, about 300 miles northeast of Los Angeles, along the line of the Los Angeles & Salt Lake Railroad. The district extends from Mt. Olcott on the north to the California line on the south,

Jan 1, 1918

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1939 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and ;I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron. and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which is issued quarterly. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administra-tion, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CON-TRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes. CONTRIBUTIONS and Other TECHNICAL PUBLICATIONS will be sent upon request. A member relay purchase an additional copy of a TECHNICAL PUBLICATION Or a CONTRIBUTION at One cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION Of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum; Canadian and foreign postage 50 cents extra. METALS TECHNOLOGY, $7 per annum; Canadian and foreign postage 50 cents extra (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum; Canadian and foreign postage 50 cents extra (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers). PETROLEUM TECHNOLOGY, $4 per annum; Canadian and foreign postage 50 cents extra. Bound volumes have been mailed to members that have requested them, and MINING AND METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and lie may purchase for $2.50 one copy of a volume not already received; additional copies of 'the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members; to nonmembers 50¢ current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum plus $1 for Canadian or foreign postage.

Jan 1, 1939

NEW MEMBERS The following list comprises the names of those persons who became members during the month of December, 1913: Members ADAMS, CHARLES W., JR., Smelting, American Smelting & Refining Co., Murray, Utah. ARMSTRONG, FRANK H., Mechanical Engineer Vulcan, Mich. ARNOLD, JOHN B., Attorney-at-Law Room 840,200 5th Ave., New York, N. Y. BOYS, HARRY R., Mining Paso Robles, Cal. CAVANAGH, JOHN L., Min. Engr., Nova Scotia Steel & Coal Co.; Wabana, Newfoundland. CHOW, KAI CHI, Student 1120 Amsterdam Ave., New York, N. Y. CLARK, ARTHUR B., Mining Engineer 72 Harbour Bldg., Butte, Mont. CURLEY, JOHN R., State Mine Inspector P. 0. Box 633, Leadville, Colo. DAVIS, ANGUS W., Mining Engineer, Consolidated Mining & Smelting Company of Canada, Trail, B. C., Canada.

Jan 1, 1914

[America,-Dear, G. C. Anniston.-Klugh, B. G. Auburn. *Poor, R. S. Bankhead.-Armstrong, W. D. Bessemer.-Creveling, J. G. Lindstrom, W. A. McKenzie, W. C. Mitchell, F. R. Birmingham.-Abbott, C. E. Armstrong, G. R. Austin, W. W., Jr. Ball, T. L. Beard, A. H. Benjamin, F. S. Blackburn, E. C. Blair, A. J. Blair, C. S. Blair. H. W.]

Jan 1, 1946

DAVE BARTLEY and Edwin F. Gray, miners, late of Shasta County, California, young, healthy, and "dead broke," arrived at Ely, Nevada, one evening in the summer of 1900. Before rustling jobs and going to work, they decided to look around the camp, and in pursuance of this plan they visited a number of claims owned by D. C. McDonald, Justice of the Peace and pioneer of the district. Among the claims he showed them were the Ruth (named after his daughter) and the Kearsarge. Both were regarded as possible gold or silver properties. For no very definite reason the two miners changed their plan and took a lease and option to buy the two claims for $3500. After the transaction was closed and the partners were alone, Gray asked Bartley what he thought of the ground. "If she's good for anything, it's copper" was the reply; and, so far as the records disclose, that was the first time that anyone ever thought of Ely or the Robinson mining district, as it was called, as a possible copper area. There were some slight surface indications of copper, but it is probable that the fact that Bartley had just come from a copper district had something to do with his predilection for a metal that was much despised around Ely. In any event, his hunch was good, and he spoke with the wisdom of an oracle. For thirty years prospectors had sought gold and silver around the camp. Several stamp mills and cyanide plants had been put up and a hundred shafts had been sunk, but fate had been indifferent in its rewards to the optimistic owners. Copper ore would have to be hauled by wagon, 150 miles down Steptoe Valley to the Southern Pacific Railroad, and there was scant hope of finding ore that would bear this cost. W. B. Graham, who ran the general store in Ely, grubstaked Bartley and Gray, furnishing them with food and mining

Jan 1, 1933

By Alec M. Crowell, C. H. Thigpen

Continuing the increase in production of crude oil and condensate started in 1937, the oil fields of South Arkansas reached a 13-year peak with 26,570,704 bbl. for the year 1942. The stability of the production branch of the industry in the area is demonstrated by Fig. I, which reflects the fact that although the number of producing wells in the state has declined from 3280 in 1931 to 2957 at the end of 1942, total production has continuously increased since the beginning of 1937. This is because all fields discovered since Jan. I, 1937, have observed spacing patterns up to one well to each 160 surface acres, the dual completion of wells where there is more than one producing horizon Eight new pools were brought into production in South Arkansas during 1942 (Fig. 2) They increased the state's crude oil and condensate reserve by 121,000,000 bbl., bringing the total recoverable reserve figure to 450,000,000 bbl. (Table 3) as of Jan. I, 1943. Abandonment of wells in the stripper areas of the state increased by 32 per cent over the preceding year, there having been 142 wells permanently abandoned in 1942. For economic reasons 279 wells were temporarily shut down as of Dec. 31, 1942. A price increase may start these wells to pumping again and also be the incentive toward the commencing of several secondary recovery projects in the fields discovered between 1922 and 1937. There were 149 wells brought into production in 1942 as against 119 for the

Jan 1, 1943

By C. H. Thigpen, Alec M. Crowell

Continuing the increase in production of crude oil and condensate started in 1937, the oil fields of South Arkansas reached a 13-year peak with 26,570,704 bbl. for the year 1942. The stability of the production branch of the industry in the area is demonstrated by Fig. I, which reflects the fact that although the number of producing wells in the state has declined from 3280 in 1931 to 2957 at the end of 1942, total production has continuously increased since the beginning of 1937. This is because all fields discovered since Jan. I, 1937, have observed spacing patterns up to one well to each 160 surface acres, the dual completion of wells where there is more than one producing horizon Eight new pools were brought into production in South Arkansas during 1942 (Fig. 2) They increased the state's crude oil and condensate reserve by 121,000,000 bbl., bringing the total recoverable reserve figure to 450,000,000 bbl. (Table 3) as of Jan. I, 1943. Abandonment of wells in the stripper areas of the state increased by 32 per cent over the preceding year, there having been 142 wells permanently abandoned in 1942. For economic reasons 279 wells were temporarily shut down as of Dec. 31, 1942. A price increase may start these wells to pumping again and also be the incentive toward the commencing of several secondary recovery projects in the fields discovered between 1922 and 1937. There were 149 wells brought into production in 1942 as against 119 for the

Jan 1, 1943

By Walter Harvey Weed

INTRODUCTION. IN a previous paper upon the enrichment of mineral veins by later metallic sulphides,† the writer has shown that certain masses of rich ores, such as are found in many mines, either near the water-line or as bonanzas in depth, are of secondary origin, and are due to a leaching of lean ore and the concentration of the material by reaction between the solution and the unaltered ore below. The geological and mineralogical evidence is believed to form an adequate basis for a chemical and physical explanation of the phenomenon. In the present paper the writer will give a brief synopsis of this theory, and will apply it more particularly to deposits of the precious metals, laying special emphasis upon the dependence of such enrichments upon the presence of iron sulphide (as pyrite, etc.) in the primary ore, and upon structural features which control the circulation of the enriching solutions below the water-level. It is believed that many, though not all, of the bonanzas and pay-shoots of rich sulphide ores, especially those carrying gold and silver, which are encountered in ore-deposits, are of such secondary origin. Apparently it is essential that the occurrence and structural relations of such ore-masses should be understood, as the success of the mine is often dependent upon the finding and extraction of these ores. A legitimate deduction, too, is that such ore-deposits decrease in value with depth. As my own studies have been mainly in Montana, my illustrations must be drawn from the ore-deposits of this and adjacent States, with such as I have noted in hurried visits elsewhere. The literature of ore-deposits doubtless affords also

Jan 1, 1902

By KENNETH CITTISGHAM

During the year 1945, the total number of wells drilled in Ohio, including the. non¬productive wells, was 1034. For the 10-year period ending with 1945, the average completions per year were 1125, the least number being 910 in 1938, and the maximum 1561 in 1941. The proportion of dry holes in 1945 was 37 per cent?about the same as for the year 1944 but exceeding the 10-year average, which was 34 per cent. The number of oil wells completed exceeded the number drilled in 1944 by about 30 per cent, the average initial per well being the same in both years. Gas-well completions were approximately 10 per Cent less than in 1944, with the average initial per well about 5 per cent greater. The difference in number of oil and gas wells in the two years was in Berea and Clinton completions, as the number of oil wells increased about 30 per cent, owing to greater activity in the two sands named, while the number of gas wells decreased because of fewer completions therein.

Jan 1, 1946

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,' conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. [t] About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5.800,000 bbl. of cement. Following are some of the cement require¬ments of the Shasta Dam specifications: [PER CEN'I Chemical composition: Loss in ignition2.25 Insoluble residue0.75 S032.25 M905.00 Uncombined lime in clinker (CaO)T.25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 35 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 6,5 Tricalcium aluminate (3CaO.Al203)Not more than 7 Tetracalcium aluminoferrite (4CaO.A1203.Fe203) Not more than 20 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following: [ ]

Jan 1, 1941

By A. R. Gregory

A shear wave velocity laboratory apparatus and techniques for testing rock samples under simulated subsurface conditions have been developed. In the apparatus, two electromechanical transducers operating in the frequency range 0.5 to 5.0 megahertz (MHz: megacycles per second) are mounted in contact with each end of the sample. Liquid-solid interfaces of Drakeol-aluminum are used as mode converters. In the generator transducer, there is total mode conversion from P-wave energy to plain S-wave energy. S-wave energy is converted back to P-wave energy in the motor transducer. Similar transducers without mode converters are used to measure P-wave velocities. The apparatus is designed for testing rock samples under axial or uniform loading in the pressure range 0 to 12,000 psi. The transducers have certain advantages over those used by King, 1 and the measurement techniques are influenced less by subjective elements than other methods previously reported. An electronic counter-timer having a resolution of 10 nanoseconds measures the transit time of ultrasonic pulses through the sample; elastic wave velocities of most homogeneous materials can be measured with errors of less than 1 percent. 5- and P-wave velocity measurements on Bandera sandstone and Solenholen limestone are reported for the axial pressure range 0 to 6,000 psi and for the uniform pressure range 0 to 10,000 psi. The influence of liquid pore saturants on P- and S-wave velocity is investigated and found to be in broad agreement with Biot's theory. In specific areas, the measurements do not conform to theory. Velocities of samples measured under axial and uniform loading are compared and, in general, velocities measured under uniform stress are higher than those measured under axial stress. Liquid pore fluids cause increases in Poisson's ratio and the bulk modulus but reduce the rigidity modulus, Young's modulus and the bulk compressibility. INTRODUCTION Ultrasonic pulse methods for measuring the shear wave velocity of rock samples in the laboratory have been gradually improved during the last few years. Early experimental pulse techniques reported by Hughes et al.2 and by Gregory 3 were beset by uncertainties in determining the first arrival of the shear wave (S-wave) energy. Much of this ambiguity was caused by the multiple modes propagated by piezoelectric crystals and by boundary conversions in the rock specimens. Shear wave velocity data obtained from the critical angle method, described by Schneider and Burton4 and used later by King and Fate sand by Gregory, 3,6 are of limited accuracy, and interpreting results is too complicated for routine laboratory work. The mode conversion method described by Jamieson and Hoskins7 was recently used by King 1 for measuring the S-wave velocities of dry and liquid-saturated rock samples. Glass-air interfaces acted as mode converters in the apparatus, and much of the compressional (P-wave) energy apparently was eliminated from the desired pure shear mode. A more detailed discussion of the current status of laboratory pulse methods applied to geological specimens is given in a review by Simmons.8 A new shear wave velocity laboratory apparatus has been developed for testing rock samples under elevated pressures. This apparatus employs liquid-solid interfaces as mode converters. The technique for generating pure shear waves at liquid-solid interfaces was developed from studies of critical angle methods.6 Two identical transducers are placed in contact with opposite ends of the rock sample, one transducer acting as an ultrasonic energy emitter or generator and the other acting as an ultrasonic energy receiver or motor. The P-wave energy emitted from the piezoelectric crystal in the generator transducer is converted into pure S-wave energy at the Drakeol-aluminum

By David R. Maneval, H. B. Charmbury

At the turn of the century, iron and coal were the keys to industrial prosperity. At that time, Pennsylvania was the leading mineral producer in the Country, producing 200,000,000 tons of coal in a typical post-World War I year. Close to 90% of the Nation's energy was generated by coal. Today, coal accounts for but 22% of the energy generated, leading to a drastic reduction in Pennsylvania coal output. In contrast with the post-World War I days, 1964 figures showed a drop in production to 93,846,480 net tons. This huge decrease has created a serious economic problem in a state so much dependent on the coal industry. Along with the reduction in coal production, employment has dropped considerably through these years (the number of miners alone has gone from 280,011 to 43,149), thus causing a heavy burden of supporting the unemployed on the taxpayers. As far back as 1939, coal operators and economists saw the problems on the horizon and the need for improvement. Realizing that research was a way to improve and stabilize the industry they demanded legislative action. The Legislature reciprocated with a small grant to The Pennsylvania State University with the provision that each State research dollar be backed with one from the industry. This initial grant laid the foundation for the further growth in coal research.

Jan 3, 1966

The following is an incomplete list of members and guests who called at Institute headquarters during the period May 10, 1919, to June 10, 1919. Victor C. Alderson, Golden, Colo. E. Fleming L'Engle, Joplin, Mo. H. Foster Bain, Washington, D. C. W. D. Mainwaring, Philadelphia, Pa. J. J. Beeson, Master Engr. Sr. Gr. W. G. Matteson, Fort Worth, Tex. Gunnar Bergstrom, Stockholm, Sweden. C. E. MacDonald, Toronto, Can. Corry T. Brown, Socorro, N. Met. Francis Nicholson, Charlotte, Va. Geo. W. Brymer, Scranton, Pa. Richard A. Parker, Denver, Colo. W. Burns, Santa Fe, N. Mex. S. B. Patteson, Jr., Allentown, Pa. H. C. Carlisle, The Pas, Manitoba, Can. G. W. Ponton, Ottawa, Canada. J. Carson Adkerson, Va. W. H. Reber, Ensign, Dallas, Tex. C. A. Cheney, Madison, Wis. T. C. Roberts, New York City. J. M. Clark, Toronto, Canada W. A. Rukeyser, Ensign, N. F. Corps. John J. Doyle, St. Louis, Mo. W. H. Staver, New York City. H. S. Emlaw, Grand Haven, Mich. D. B. Sterrett, Washington, D. C. E. Francis, Birmingham, Ala. T. V. Smirnoff, Russia. Rudolf Gahl, Denver, Colo. E. C. Templeton, New York City. Emit Gthmann, Baltimore, Md. H. A. Toblemann, Ajo, Ariz. A. B. Hardie, Philadelphia, Pa. Priestley Toulmin, Birmingham, Ala. Clarence M. Haight, Franklin, N. J. M. R. Walker, Baltimore, Md. N. V. Hansell, New York City. H. A. Wheeler, St. Louis, Mo. C. A. Heberlein, Nacosari, Mexico. D. B. Whitaker, Santiago, Cuba. Pierre Hines, Milwaukee, Wis. A. W. G. Wilson, Ottawa, Can. J. S. Hollings, Brymoba, Wales. Oba Wiser, Hanover, N. Mex C. Vey Holman, Maine. Harry J. Wolf, Denver, Colo. H. H. Howry, Denver, Colo. F. H. Wood, Mt. Vernon, N. Y. W. Spencer Hutchinson, Boston, Mass. J. P. Wood, New York, N. Y. W. B. Kunhardt, Reading, Pa. Lawrence Addicks sailed on May 17 for London; lie expects to be absent from this country for several months. Roy H. Allen has accepted a position in the research engineering department of the National Aniline & Chemical Co., Buffalo, N. Y. H. Foster Bain has gone to Shanghai, China, where he expects to remain for some time. Percy J. Bandy has accepted a position with the Cia. Minera del Mirasol S. A., at Cusihuiriachic, Chihuahua, Mexico. J. H. Batcheller is now with the North Midas Copper Co., St. Helena, Alaska.

Jan 7, 1919

The 128th meeting of the American Institute of Mining and Metallurgical Engineers constituted a two weeks trip through the Great Northland of Ontario and Quebec and was a most memorable occasion. The last visit of the Institute to Canada was made in 1907 when the mines, which now have brought world wide fame to some of the camps, were not yet dis-covered. The party reached its greatest numbers at Porcupine where 167 visitors and nearly one hundred local members participated. Five members of the party from the States were on the previous trip in 1907. They were Mr. and Mrs. L. D. Huntoon, John Stevenson and son and E. F. Eurich. The Minister of Mines for the Province of Ontario attached his private car to the "Mining Engineers' Special" and made the complete trip through Ontario. This was a happy incident in many ways and gave the visitors an opportunity to discover a spirit of mutual accord between the Minister and mining industry that might well be emulated elsewhere. Two compartment cars and one standard Pullman with the Institute members from New York and the metropolitan district were attached special to the 6.15 p.m. Lehigh Valley train from New York, Sunday, Aug. 19, en route to Toronto, where was held the first session of the Institute's 128th Meeting.

Jan 9, 1923

Edward Payson Mathewson EDWARD PAYSON MATHEWSON, President of the American Institute of Mining and Metallurgi-cal Engineers, was born in Montreal, Canada, Oct. 16, 1864, of Scotch-Irish ancestors. After preparation in private and public schools, he graduated from McGill University with the degree of Bachelor of Applied Science, in 1885, having specialized in mining engineer-ing and metallurgy. He spent the succeeding summer as a surveyor with the Canadian Geological Survey, being employed in the lake region of Ontario. The following spring he left Canada for Colorado, where he immediately obtained a position as assayer with the Pueblo Smelting & Refining Co. Within three years he became superintendent of the plant, and his success in this position brought him to the attention of the Guggenheim family, whose employ he entered in 1897. He was first in charge of their Pueblo plant, but was soon transferred to their refinery at Perth Amboy, N. J. During the succeeding five years he was in charge of important smelting operations conducted by the firm in Mexico and South America. In June, 1902, Mr. Mathewson accepted a position at the Washoe reduction works at Anaconda, soon thereafter becoming manager of the property. It is unnecessary to recount the improvements and enlarge-ments instituted at that plant under his management, until it became the Mecca of all metallurgists visiting the United States. The esteem in which Mr. Mathew-son was held, not only by the men directly under him, but by all his fellow citizens, was expressed in a send-off such as probably no other plant manager has ever received, when he left Anaconda in October, 1916, to accept the general managership of the British America Nickel Corporation, at Nickelton, Ont., Canada. Soon thereafter Mr. Mathewson accepted an appoint-ment as director of the American Smelting and Refining Co., acting as consulting metallurgist for the company and its subsidiaries. In November, 1919, he resigned this position and opened an office in New York City as a consulting metallurgist.

Jan 3, 1923

By B. R. Queneau

[ ] B. R. QUENEAU-One of the difficulties in metallurgy has always been a lack of precision in measurement, and I think the authors are to be congratulated on developing a method which will give us an accurate and dependable quantitative estimate of the amount of retained austenite. O. ZMESKAL*-As Chairman Queneau said, this is indeed an ingenious and needed determination. We have seen figures presented of 1/2 pct retained austenite determined, and I would like to ask the authors the lower limits of this method. How far down do they feel they can go in improving the technique still more?

Jan 1, 1948