Search Documents

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By A. L. Titchener, M. B. Bever

FROM their investigation of the martensitic transformation in Cu-Zn alloys, Greninger and Mooradian' concluded that there was no critical temperature at which martensite formation began in this system. Recent unpublished work by Gen-evray With two compositions of brass revealed the existence of a critical temperature, which is a function of composition and stress. In the work reported here the temperature range of the martensitic reaction was studied as a function of composition in high purity Cu-Zn alloys. The specimens were about 4 in. long with a diameter of 1/16 in.; their compositions are given in Table I. They were heated under vacuum for 5 min at 5" to 10°C below the temperature of incipient melting, and quenched into brine at about — 10°C. Specimens of alloys C, D, E and F were obtained with little or no precipitated a phase. Many attempts yielded only three usable specimens of alloy B, and even these contained appreciable amounts of a. All efforts failed to preserve metastable p in alloy A (containing 38.02 pct Zn and 0.002 pct each of Pb and Fe). The transformation was studied by measuring the electrical resistance during continuous cooling and heating of each specimen at similar rates. The cooling media were alcohol with dry ice from room temperature to — 78°C and a bath of petroleum ether and methyl cyclohexane (75:25), cooled by liquid nitrogen, from —78" to about —150°C. Readings were also taken at —195 °C in liquid nitrogen. Fig. 1 illustrates a typical experiment. The relative resistance is obtained by assuming the known

Jan 1, 1955

Last November, when the British Educational Mission was visiting this country, letters were sent to the various mining schools asking what arrangements had been made for cooperating with British and. French schools. Of the eleven schools from which replies were received, none had taken any definite steps in this direction. The Colorado School of Mines, though, stated that it was offering scholarships to all men who had served in the U. S. Army and Navy during the war. A letter was also sent to Sir Henry Miers, Vice-chancellor of the University of Manchester, who was the head of the British Mission. He replied as follows: "In my opinion the mining profession is second to none in the responsibility of the duties which it involves or to which it leads in all parts of the world; also it is a. profession in which the student or teacher has much to gain by migrating to foreign countries. This applies in a special degree to British students coming to America where they will be able to enlarge their views by a widened experience. We (the Mission) have everywhere found the most, cordial acceptance of such proposals. Several of the British Universities have recently instituted a new doctorate of philosophy attainable after 2 or 3 years course of advanced study; this scheme includes Oxford and Manchester. The conditions admitting to the degree course are that the applicant should be a graduate of an approved University and should show evidence that he is qualified to pursue the course which lie proposes." In a conversation with Prof. Alfred C. Lane, of Tufts College, Sir Henry Miers said that students from Great Britain should be most easily attracted to America, both to universities and colleges and technological institutions.. He doubts, however, whether Great Britain can offer America, in this respect, as much as America can offer her. Prof. Lane, though, is quite sure that, especially for geologists, there is much to be

Jan 2, 1919

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By Donald L. Ball

The equilibrium of boron nitride, gaseous nitrogen, and solute boron was investigated in Fe, Fe-C, and Fe-Si rnelts by the Sieverts technique. The free ellergy of dissociation of boron nitride, involving -the implied standard states, was evaluated in the range 1400" to 1600°C as: ?Fo = 38,000 - 23.5T, cal ber mole The solute-solute interaction coefficients eBB, ecB , and eg were determined as 0.058, 0.22, and 0.078, respectively. BORON is an important ingredient in some types of steel and cast iron. It was employed at a particularly high level, 0.01 wt pet, in the as-cast malleable iron "CentraSteel".1 In this material, the boron concentration was critical in order to assure graphite, and avoid primary cementite, in the as-cast structure. One possible function of the boron in this alloy was the nucleation of graphite through the agency of boron nitride, which, conceivably, precipitated from the melt during cooling. A research program was instituted to assess the validity of this proposed mechanism. The first undertaking, reported here, was a determination of the thermodynamic possibility of boron nitride precipitation. Data available in the literature on the activity coefficient of solute boron in iron-base melts are inadequate for the present purpose. They will be reviewed briefly, however, so that comparison can be made, when

Jan 1, 1968

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air-pollution control is included. However, there are clear indications that the natural gas supply from the conliguous 48 states and continental shelves will not keep up with this rapid growth in demand indefinitely. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale -by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current mine-mouth prices - 60-70 million tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase in gas demand. Although annual discoveries (gross additions to proved reserves) of natural gas in the United States are still on a general upward trend from the current level of 22 trillion cu ft annually, most forecasters do not expect this to increase substantially in the foreseeable future. For example, the updated (to include 1966 and 1967 data) mathematical model of natural gas discovery and production in the U.S. developed by the Institute of Gas Technology (IGT)' projects that discoveries will level out at about 25 trillion cu ft annually in the late 1970's and during the 1980's and then decline to about 21 trillion cu ft by the year 2000 (Fig. 1). This adds up to a new supply for the period 1968-2000 of about 790 trillion cu ft. Experts who usually reflect the producers' viewpoint, such as Radford L. Schantz of Foster Associates,* are relatively more pessimistic. In contrast, a forecast just made by the U.S. Dept. of the Interior is much more optimistic.3 It assumes an increase in gas discoveries of 2.2% per year over the period 1965-80, reaching about 30 trillion cu ft in 1980. If this rate of increase were extended to the year 2000, annual discoveries would reach 46 trillion cu ft at that time, for a total over the period 1968-2000 of about 1100 trillion cu ft. To these forecasts of new gas discoveries must be added proved reserves of roughly 290 trillion cu ft,4 bringing total U.S. supplies for the rest of the century to nearly 1100 trillion cu ft (IGT) and possibly as high as 1400 trillion cu ft (U.S. Dept. of the Interior). This is approximately the same range as that of two estimates of total remaining recoverable natural gas supply: Potential Gas Committee, 980 trillion cu ft5 and IGT, 1450 trillion cu ft.6 Only the 1965 estimate by the U.S. Geological Survey7 suggests that economically recoverable natural gas supplies will not be exhausted around the end of the century. These forecasts are, naturally, based on the assumption that changes in technological, economic, and regulatory environment as they affect the gas industry will be of an evolutionary, not revolutionary, nature. The various forecasts of potential natural gas supply must now be compared to forecasts of natural gas demand (Table I). The general consensus is that the recent Future Requirements Committee projection to 1990' (extended to the year 2000 by the most recent U.S. Bureau of Mines (USBM) projection9) represents the minimum gas requirements (Table 11). They add up to a total of 1030 trillion cu ft for the period 1968-2000. Even this minimum anticipated gas demand exceeds the total remaining supply estimate by the Potential Gas Committee and would nearly exhaust the proved reserves plus new discoveries projected by IGT. The supply situation would appear much tighter if the demand projections of the Texas Eastern Transmission Gorp.10 and the American Gas Assn.(A.GA.)'' were used (Table I). Yet, these higher forecasts probably do not include the effects of such new markets as gas fuel cells, use of liquefied natural gas as a transport fuel, etc. They also may not fully reflect the impact of air quality control on the fuel market. Obviously, the probable discrepancy between projected supply and demand can only be accommodated in four ways. 1) Rapid increase in exploration and drilling activity to provide new supplies in the amount projected by the optimistic U.S. Dept. of the Interior forecast, coupled with an increase in net pipeline imports from Canada and Mexico from the present 0.5 trillion cu ft per year

Jan 1, 1970

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction problems under various multiple seam conditions, but few of them are specific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multiple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By George A. Packard

The experiments here described were made under my supervision while temporarily acting as head of the Department of Metallurgy at the Missouri School of Mines, at Rolla. The work was done by Messrs. W. E. Brown, W. C. Richards, and F. L. L. Wilson, and the description of the results forms a portion of a thesis presented for the degree of Bachelor of Science. These results are submitted because I have seen no description of the application of pot-roasting to the treatment of a copper-concentrate. This work followed that already described in the discussion of the Lime-Roasting of a Galena-Concentrate,' and was similarly occasioned by the lack of a furnace of the reverberatory type in which the copper-concentrates could be smelted. The material for the tests was a mixture of three lots available. The first consisted of 8-mm. ,jig-concentrates and the second of 0.5-mm. table-concentrates, from the San Juan district, Colo. Both contained pyrite, chalcopyrite, and galena. The third was a lot of copper-ore, found in the laboratory, which had been crushed through 8-mm. screen, and had at some previous time, before the laboratory roasting-furnace was torn down, received a partial roasting. The analyses of these ores are given in Table I. In order to determine the applicability of pot-roasting as to each lot of ore, and the effect of varying proportions of lime, six preliminary tests were made in a " size N " Battersea crucible, 9 in. high by 6 in. in diameter at top, with a 5/8-in. hole bored through the bottom. The crucible was set in the upturned elbow of a 2-in. pipe, the joint being luted with clay; and air was obtained from a receiver supplied by a compressor. The

Jan 1, 1908

Abel, Charles Edwin, Student, Univ. of California Los Angeles, Cal. '31 Adams, Horace M.5148 Benton Ave., Downers Grove, Ill. '31 Ahlskog, Harold A., Student, Washington State College Pullman, Wash. '30 Aldridge, John, Student, New Mexico School of Mines Sbcorro,, N. M. '30 Allen, Hugo K., The Univ. of Texas 104 W. 33rd St., Austin, Tex. '31 Ames, Marshall B., Student, Washington State College Pullman, Wash. '31 Ancell, Virgil F., Student,. Missouri School of Mines Rolla, Mo. '30 Anderson, Norman John, Student, South Dakota School of Mines Rapid City, S. D. '32 Annett, Norman T., Student, Mackay School of Mines, Univ. of Nevad Reno, Nev. '32 Apablasa, Salvador C., Student, Univ. of California Los Angeles, Cal. '31 Armstrong, James Arthur, Jr., Student, Michigan College of Min. & Tech., Houghton, Mich. '31 Armstrong, John R. Box 274, Neosho, Mo. '31 Armstrong, Robert H., Student, Lafayette College Easton, Pa. '31 Armstrong, Thomas E., Student, Univ. of California Los Angeles, Cal. '31 Arnot,. Paul H 2617 Haste St., Berkeley, Cal. '31 Ashby: Harve I., Willow Creek Mines Wasilla, Alaska. '31 Aud, Robert A., Student, Lafayette College Easton, Pa. '30 Augenthaler, Robert L., Student, New Mexico School of Mines Socorro, N. M. '32 Augustine, Grant, Jr., Instrument man, Min. Dept., Fairbanks Exploration Co., Fairbanks, Alaska. '31

Jan 1, 1932

IDO not want to omit anything in which fire or its operation has a part, if I know or can tell it, and have already told you so many other useful, powerful, and ingenious effects (finally of powder and other' fire deadly and very injurious to all living things, indeed, composed for the destruction of those who possess it as well as those who do not) but I do not want the end of my writing to be in tragedy. Therefore I wished to tell you how, from these fires composed of forceful and horrible mate¬rials bringing harm and terror to men, a happy and pleasing effect is also produced and, instead of fleeing from it, the people willingly go to see it. Among others I remember that it was once customary to use these in Florence and in Siena, more than elsewhere. The chief feast day celebrated. by one of these cities is the day of the birth of Saint John, and the other is the Assumption of Our Lady, on the fifteenth of the month of August. In the morning they visit the shrines with great devotion and solemnity, displaying their pomp as much as possible, and later they hunt lions, wild bulls, untamed horses, and many other animals. In the same public squares there was also erected as a decoration an edifice fixed in the ground in the middle of this space, or hanging from a heavy rope crossing between the loftiest points of equal height that could be found in that place. This they have done and still do, and perhaps in time to come will continue to do when opportune. This structure was usually of wood; indeed it is necessary that the latticework of its construction be made only of this. It was covered and en¬larged by tying and fastening hay on top to bring it almost to completion and then papier-mâché was applied. [165v] The figures were first appropriately painted and made of a combination of vessels one above the other, developing various decorative figures in relief which should represent some fable or history and should not appear haphazardly made or without understanding. Now the master proceeded to arrange these figures in a composition according to his skill or art of design, and likewise planned

Jan 1, 1942

By AIME AIME

THE complete list of papers for the meeting of the Petroleum Division that is to be held" at Tulsa,' Thursday and Friday, Oct. 3 and 4,, with assignment to individual sessions is given below. THURSDAY MORNING First Session Well Spacing Theory of Well Spacing-By W. P. Haseman. Discussion by S. C. Herold, J. R. Suman and Lester C. Uren. Well Spacing in the Long Beach Field, California-By - Stender Sweeney. Discussion by C. H. McNeese; R. R Brandenthaler and W. V. Vietti. Well Spacing in the Bradford Field, Pennsylvania-By Paul D. Torrey. Discussion by A. F. Melcher, R. M.. Haskell, J. B. Umpleby and J. B. Newby. Results of Different Well Spacing in the Salt Creek Field, Wyoming-By Fred E. Wood. Discussion by Sam Grinsfelder and Kenneth B. Knowles.

Jan 1, 1929

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

PRACTICAL designs for good "home made" molybdenum furnaces are hard to find in the literature. The one described briefly below left something to be desired but was good enough to operate as a rather long (30 in.) two-zone furnace for periods of over 2 months at temperature (1400° to 1600°C) without shutdown. The principal problem in our application was to establish a temperature profile with two distinct constant-temperature zones and no dip between the zones. This and other problems mentioned below would not arise, however, if both zones were operated at the same temperature and if a shorter furnace were acceptable. Since molybdenum windings oxidize very rapidly when heated in air, impervious refractory tubes were used for both the furnace core and the outer jacket tube shown in the accompanying figures. A protective atmosphere of forming gas (10 pct H2, 90 pct N2) was continuously passed through the gas-tight annular volume between the core and outer jacket. The water-cooled copper ends shown in Figs. 1 to 3 sealed the ends of the tubes. Annealed molybdenum wire (40 mil) was wound on the recrys-tallized alumina core (35.5 mm OD by 28.5 mm ID by 30 in.) at a spacing of 0.36 in. The spacing was reduced to 0.29 in. close to the ends to partially compensate for end heat losses. Fig. 2 shows two molybdenum-ground lead taps off the center of the winding to produce the two independect temperature zones. The ground lead was insulated with 1/4-in. alumina tubing and connected to the grounded copper end by passing the wires through the gas port tube and crimping each wire into notches cut at the mouth. To prevent sagging of the core at high temperatures, refractory "troughs" were cut from alumina and mullite tubing to cradle the core. The support "troughs" which were 6 in. long and located about 5 in. from each end of the annular volume also served as radiation shields. In view of the different expansion coefficients and operating temperatures of the core and outer jacket (3.5 in. OD by 3 in. ID by 30 in.), the ends of the tubes were smoothed and squared to produce good sealing surfaces, and the core was ground 1/32 in. shorter than the outer tube. The power terminals were passed through their respective conductor ports which were internally lined with alumina tubing and sealed with Armstrong adhesive A-6 leaving about 1 in. of protruding lead wire for external connections. (Adhesive A-6 is a two-component system consisting of an epoxy-type resin with a mineral fibrous filler and an amine catalyst.) Figs. 1 and 3 show the entire assembly of concentric refractory tubes, copper ends, and sealing o rings, held together with two brass flanges and 3/8-in. bolts with heavy springs for dimensional flexibility. The furnace shell (19 by 19 by 30 in.) consisted of a steel frame with sheets of transite forming a box. The copper ends protruded through two 3.75-in. circular holes cut at the center of each transite square end. Thermal insulation next to the transite exterior was effected by K-23 B&W bricks alld in a central volume of approximately 9 by 9 by 30 in. a row of K-30 bricks was lined up to support the hot assembly. The rest of the volume around the outer

Jan 1, 1965

By Robert A. Jankowski, Charles D. Taylor

The objective of this program was to conduct dust surveys at six longwall sections having double-drum shearers, that were regularly in compliance, and to identify the dust control techniques that were the most effective. As each of the mines selected had a record of regular compliance with the Federal Dust Standard, all sampling was "short-term" (often less than 30 minutes) and no attempt was made to relate the survey results to dust-sampling results obtained by the companies for compliance purposes. The sampling procedures (1) used during this survey were developed jointly by the Bureau of Mines and Foster-Miller Associates, Inc. In addition to monitoring dust levels, measurements were also taken throughout the shift to monitor airflow along the face and water usage on the shearer. This program was a cooperative effort of the Bureau of Mines and the Mine Safety and Health Administration (MSHA). The following MSHA health specialists contributed to its successful completion: Paul Lenyo, CMS&H, Dist. 2; Ellis Mitchell, CMS&H, Dist. 3; Carl Jenkins, CMS&H, Dist. 4; David Stritzel, CMS&H, Dist. 8; and John Prelc, CMS&H, Dist. 9. RESULTS CUTTING SEQUENCE - WORK LOCATION At all mines surveyed, an important factor in controlling dust exposure at the shearer is the design of the cutting sequence so as to allow the shearer operator to work most of the time on the intake-air side of the lead drum. It is generally accepted that most of the dust generated by a double-drum shearer comes from the lead drum, which in the raised position normally takes a full sump. Because the position of the drum that is in the raised position determines the horizon control, the operator must be close enough to carefully monitor its operation. Therefore, his position relative to the lead drum has a significant effect on his dust exposure. Dust profiles, such as those constructed from data collected at Mines A and B (Figure 1), show the large gradient in dust concentrations that can exist between the intake and return air side of the lead drum. When the primary cut is taken head to tail, the lead drum is downwind and dust levels can be maintained at a low level until air has passed the shearer (Mine A). Thus, shearer operators can stay in relatively uncontaminated air. When the primary cut is taken tail to head, the lead drum is upwind of the shearer controls, resulting in higher dust concentrations at the shearer operator's work location (Mine B). At the mines where this cutting sequence was used, it was company policy for the shearer operators to walk on the intake side of the lead drum, returning to the controls only to adjust the height of the lead drum. DIRECTED WATER SPRAYS AND PASSIVE BARRIERS It is not always possible to keep the shearer operator on the intake air side of the lead drum. Various techniques have been tried to keep the dust generated by the shearer away from the machine operators when they work adjacent to the shearer. At all mines visited, the external water spray nozzles were directed so that dust from the shearer was directed downwind and toward the face, and away from the shearer operators. The effectiveness of using external water sprays to keep dusty air close to the face was noted during Bureau of Mines efforts to develop improved water spray systems (2). Laboratory and underground tests showed that water sprays located properly and directed downwind can create aiflow patterns that move dust generated by the shearer toward the face and away from the shearer operators. Sprays directed upwind, into the airflow, can actually move dust away from the face

Jan 1, 1982

THE CHAIRMAN.-Thank you. Since the papers are rather closely related, I think rather than taking them one at a time we will entertain discussion on any of these problems at this time. W. A. REICH.*-We, of course, quite a while ago got the yellow light that Mr. Cole spoke of, and like everyone else immediately started to study silicon bronzes and brasses. We were interested in the silicon bronzes and brasses because we felt that in order to replace gun metal which makes up a large part of our use we needed something with an elastic limit at least equal to that of gun metal. That means at least 12,000 lb. per sq. in. This study was aimed only at tin conservation. Then we dropped the study of silicon bronzes because high purity copper which is needed in their manufacture became a scarce item. To make a long story short we have recommended to our designing engineers that they use 85-5-5-5 wherever possible because 85-5-5-5 we understand can be made entirely from scrap with little or no tin addition. 85-5-5-5 has a lower elastic limit than 88-8-4, so we felt that we would need another substitute material, a structural alloy with an elastic limit equal to that of 88-8-4, and we immediately turned to the manganese bronze type of alloy. The poor foundry properties of standard manganese bronzes were mentioned by Mr. Thieme and since we feel that high zinc content is largely responsible for this difficulty, our development is directed along the lines of uncovering a material with a lower zinc content and which gains its elastic strength from the addition of other alloying elements, such as, aluminum, manganese and iron. It must be possible to make this alloy entirely from scrap with no additions of scarce high purity material. I would appreciate an expression of opinion on how low we can go in zinc content with this type of alloy without seriously impairing the availability, and how high we can go in aluminum content without making use of aluminum restricted for that use. We assume that the maximum lead content must be placed at 1 ½ per cent to insure good availability and we feel that about I per cent of tin in the alloy would improve salt water corrosion resistance similar to the effect of tin in Admiralty Metal. Has anyone here had experience with the effect of tin and lead on the weldability of such an alloy? C. S. COLE.-What percentage of lead and tin? W. A. REICH.-About 1 per cent of lead and 1 per cent of tin. We are studying the weldability of the alloy but perhaps someone already has the answer. (Pause, no answer) The claim has been made that 1 per cent of lead can be added to certain silicon bronzes without impairing their properties. A silicon bronze with a low zinc content requires high purity copper in its manufacture but if say the 15 per cent zinc, 44 silicon balance copper alloy could be made, with a I per cent lead content, some quantity could be made from scrap. We do not know whether the aforementioned is

Jan 1, 1943

New York, March 18, 1913. MR. CHARLES F. RA ND, President, New YORK, MARCH American Institute of Mining Engineers. Dear Sir: In connection with the official notice of Dr. Raymond's unanimous election by the Directors as Secretary Emeritus, we wish to place upon record certain statements concerning his services to the Institute which we think have not been published., and may not be generally known to the majority of our fellow-members. When the Institute was formed in 1871, Dr. Raymond acted as Secretary of the Founders' Meeting, and became the first Vice-President of the Institute, and, by request of the aged and beloved David Thomas, who was the first President of the Institute, Dr. Raymond discharged all the duties of the office of President, to which he was later formally elected in 1872, and which lip held for three years. During that time, he visited Europe, and through his acquaintance and reputation abroad, established those international relations of the Institute which proved so important in later years. He also enlisted the support of the mining engineers and metallurgists of the Pacific Slope, who would not otherwise have been disposed to join a society originating in the East. And for twelve years he attended; at his own expense, nearly every meeting of the Institute, wherever held, giving to it without remuneration his best service, and sacrificing for it many professional and private interests.

Jan 4, 1913

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

L. D. GODSHALL, Everett, Washington: This very interesting paper cannot fail to command the attention of every one who has ever had experience in the amalgamation of gold-ores. I wish to call attention to three very important facts brought out very prominently by the paper, namely: 1. The extent of accumulation of amalgam on copper plates in the form of scale, not removable in the ordinary manner; 2. The change in the relative quantity of the two metals in the amalgam as we. recede from the battery-discharge; 3. The difference in fineness of the bullion obtained from the above-mentioned scale as compared with the bullion from the daily clean-ups. From Mr. Bayliss's figures we find that during the life of the plate in question 14,942 tons of ore were crushed, yielding amalgam of the value of $5.03 per ton, or a total value of $75,158.26. The amalgam accumulating on the plate during this time as scale, we find to have had a value of $8340.54, or $0.558 per ton of ore treated, representing 11.09 per cent. of the total amount of amalgam saved in the ordinary clean-up; or, taking the amalgam saved by daily clean-up plus the amalgam-scale as representing the total saved on this plate, or 100 per cent., we find that the daily clean-up saved 90.01 per cent., while the scale represented 9.99 per cent. The above figures do not include some additional amalgam still adhering to the plate after scale had been removed. We are told that this was not an exceptional case at the Drum Lummon, but that other plates have even yielded a third more than the one in question. The interesting query now comes up, whether this experience at the Drum Lummon is exceptional or universal at all mills; and another question arises, as to how long such an accumulation might continue,

Jan 1, 1897

By Michael Perch

The fact that coal is a complex organic material and heterogeneous in composition has made its study extremely difficult, particularly in regard to obtaining a fundamental concept of the processes involved in the formation of coke. It has been stated recently that coals are natural polymers and that in a complex reaction such as occurs during carbonization the differences between coals are quantitative and not qualitative. Such being the case, it would be expected, therefore, that a series of coals subjected to exactly the same conditions of coking would produce results that should be related quantitatively to the chemical analyses of the individual coals. In the past, however, this fact was not generally recognized and consequently many empirical test methods were devised for testing coals. The interpretation of the results obtained depended upon comparing a set of data with other data on coals of known characteristics. The testing procedure had to be con- ducted in precisely the same manner each time and not the least requirement in making the interpretation was experience. The test methods varied from those utilizing a gram of coal to the plant-scale tests in which one or more ovens were charged with the test coal. The aim had been principally to find some simple, inexpensive means by which the coke-making and other properties of coal could be predicted. It is not necessary to emphasize the importance of these endeavors, for anyone acquainted with the problems involved in the selection of coals for making coke is well aware of the time and expense involved in making a series of definitive tests.

Jan 1, 1949

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970