Search Documents

By Truman Aldrich

THE Clinton group of the Silurian holds the red or fossiliferous ore; its outcrops have been mapped by the State or U. S. Geological Survey. This group is from 100 to 500 ft. thick in Alabama. There are places where it is entirely missing (doubtless islands in the Silurian Sea). In Etowah County, in part of Greasy Cove and vicinity, the upper seam is a coral reef impregnated with the red ore; in this same county, step, faults bring up the ore in three or four separate ridges practically parallel. In Blount County and on Raccoon Mountain, the ore runs under the carboniferous rocks and outcrops in the valleys. In examining some bore holes made in drilling for oil, the writer found the Clinton group continuing under the Warrior coal field wherever the drill has gone deep enough. It demonstrates the possibility of a source for red ore not seriously thought of until lately. The following bore holes made principally for oil, given in Bulletin No. 22, Geological Survey of Alabama, show the presence of either ore or red rock, and suggest vast resources yet to be outlined and developed for ore in the future. The locations are given by number on the map. Hole No. 1 was drilled 6 miles southeast of Russellville, Franklin County, by the Woodward Oil & Gas Co. It passed through 160 ft. of Clinton, but only a small show of red ore was found at 1280-1400 feet. A test well, No. 2, drilled near Atwood, Franklin County, in section 26, township 8, range 14, penetrated the Clinton at 1608 ft. and found 38 ft. of limy red rock, also 8 ft. of some blood red ending at 1820 ft., making 46 ft. of red rock in all. It is reported that some good ore was cut through but this work was done by a churn drill. The hole was continued by diamond drill from here. At least 400 ft. of the formation was classified as Clinton.

Jan 10, 1924

ZAY JEFFRIES (written discussion*).-I have read with much interest Mr. Ruder's discussion of Professor Howe's paper, "The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite." I am yet of the opinion that my first explanation' of Mr. Ruder's samples is substantially correct. In that explanation I did not intend, however, to convey the impression that "reversed inheritance" was the general rule nor even of common occurrence but rather that." Non-inheritance" was the general rule. Mr. Ruder suggests that a " perfectly formed" grain is an indication of inheritance. The grains in my Fig. 52 are perfectly formed and in fact more nearly equiaxed than those in Mr. Ruder's Fig: C,3 yet the grains in the former are known not to be inherited but to have been formed by the partitioning of larger austenite grains. On close examination of Mr. Ruder's Fig. C the very shapes of the grain suggest partitioning. Again, the grain size (25 to 30 grains per square millimeter) is at least 10 or- more likely 20 times smaller than might be expected of the austenite from which these grains were .formed under the given time and temperature conditions. Mr. Ruder's newer results on electrolytic and Armco iron are most interesting and instructive. His results fit in. nicely with my conclusions 5, 6 and 10.4 His photographs, however, indicate that the thickness of the pieces of sheet metal are such that abnormal grain growth is promoted. He indicates that equilibrium grain size after heating to 950° C., with furnace cooling, is about the same as his Fig. 1, above. I estimate this to be approximately one-half -grain per square millimeter, or 40 times as large as I have obtained with the same material (Armco iron) after heating Y4-in. bars to 1300° C. for 2 hr. and cooling in the furnace. The effect of thickness of sample on grain size is one which needs more attention.

Jan 3, 1918

By Theo B. Comstock

TO the large majority of visitors the unique features of the National Park are interesting chiefly on account of their novelty. Scientists of all schools may find here food for reflection, and much that is rare and marvelous; but the real, practical uses of the reservation, aside from its pleasure-giving adaptations, are not as yet fully appreciated. Since 1873, the writer has on frequent occasions expressed freely his own views upon the proper means of utilizing the Park for the best interests of science.* Some of the recommendations made have been adopted by the authorities. At the suggestion of friends I present here a brief statement of facts concerning matters which may be of advantage for visiting engineers to know, hoping that the very limited stay of the Institute may thereby be rendered a little more profitable, and that our common profession may possibly receive some benefit. First, then, it should be understood that, as in many other cases in. the West, the present routes to the Park from the south are not the most direct. The expedition of Captain (now Major) Jones in 1873 discovered a practicable route for a, wagon or railroad via the head of Wind River, through To-gwo-tee Pass and Two-Ocean Pass, by which the distance from Point of Rocks, Wyoming, on the Union Pacific R.R., to the Yellowstone Lake, is only 290 miles. Eventually, it is probable that a railway line from Cheyenne or some other point in Wyoming will be constructed, which, taking advantage of

Jan 1, 1888

By J. WILLIAM WETTER

WHEN the privilege was extended to me to address this meeting I could not help but make a mental review of my own activities and experiences in connection with association work. After having spent about 16 years in the mining engineering field, I entered into the operating branch of coal mining which afforded, about 12 years ago, my first opportunity of attending a meeting of our local Association and sitting in with the "big boys" of the industry. This was quite a thrilling experience because I had heard a great deal about the various operators who belonged to the Association and knew, or at least thought I knew, that a certain group dominated its affairs and that a "clique" was in control of a sizable "roller" which could be "steamed up" at will to flatten out any opposition which might appear upon the horizon or under it, too, for that matter. Now, I was to have the privilege of observing this "clique" at first hand, of seeing a small group making the policies and shaping the destinies of a great industry and planning the activities of an important Association while a large majority of the members would sit by either complacently or otherwise with the full knowledge that the "roller" was in waiting to reduce them to ribbons at the first sign of resistance.

Jan 1, 1930

By Byoung Whie Lee

In order to investigate the change in surface energy as a function of cold work ad environment, the contact angles between a liquid and the surface of elec-tropolislzed aluminum with various degrees of cold work were measured. Specinlens cut from aluminum rod (99.99 pct Al) were annealed at 600°C for 24 hr and then cold compressed parallel to the drawing di-rectzon of the rod in increments of approximately 10 pcl from 0 to 70 pct. The sections, taken transversely to the drawing direction, were mechanically and electro chemically polished. Contact angles between the sessile drop of distilled water, glycerin, and glycol and the specimen surface were measured optically. The differences in interfacial energy were calculated from the contact angle data. The effects of chemical washing and surface roughness of the specimen on the contact angle were also studied. The liquid contact angle was a linear function of the degree of cold working (D) ad changed markedly with differed liquids. THE plastic deformation of polycrystalline metals induces a preferred orientation in crystal structure. A preferred orientation changes the atomic density of a metal surface. This change in surface atomic density brings about the changes in surface interactions of the metals."' Also, the plastic deformation of metals raises the internal energy by increasing the stored energy.' Consequently, the total Helmholtz free energy of the metal increases and, in turn, the surface free energy of the metal. In order to study the effect of plastic deformation on solid surface phenomena, the liquid contact angle of a sessile drop made on cold compressed and elec-trochemically polished aluminum was measured. The preferred orientation in aluminum, due to uniaxial compression, is known to be [110] direction parallel to the compression axis. However, this description is only a first approximation of a rather complex orientation. In actuality, half the crystallites are more than 10 deg from this orientation, regardless of the amount of compression." For randomly oriented fcc crystals, the average surface atomic density can be calculated as follows: The number of atoms in a unit volume is 4/a3, where a is a lattice constant. Hence, the number of atoms per unit surface area is about (4/a3)2/3 = 2.52/a2 However, when the preferred orientation took place along [110] direction, the surface atomic density is as follows: The area of (110) plane of a unit cell, considering ridges and valleys, is BYOUNG WHlE LEE, Member AIME, is Research Metallurgist, Atomic Energy Research Institute of the Republic of Korea, Seoul, Korea. Manuscript submitted May 29, 1968. IMD 2 x J2- a x Ga = 6a2 Since this plane contains 4 atoms, the surface atomic density is 4i6a2 = 2.3/a2 Upon changing from random to preferred orientations, the surface atomic density decreases about 10 pct. The increase in the stored energy and the change in surface atomic density due to plastic deformation would certainly alter the surface tension of a metal. EXPERIMENT High purity aluminum rod of 6-mm diam (99.99 pct Al, obtained from Johnson, Matthey & Co., Ltd, London, England) was cut into sections approximately 1 cm long. The transverse cross section was mechanically polished. Then, the specimens were annealed in air at 600°C for 24 hr. Thus, eight annealed specimens were uniaxially compressed at room temperature from 0 to 70 pct of cold working with an increment of 10 pct. The extent of cold working was determined by the percentage of reduction in axial length to the original length. The specimens were further polished mechanically and, then, electrochemically with the Modern Battelle Type 1 electropolishing solution with a current density of 0.3 to 0.4 amp per sq cm and an electrode potential of 8 to 12 v at the solution temperature of 78" to 82°C for approxirr~ately 5 min. The Modern Whlte Diffusing Screen \t/ --------------- re Goniometer for Mercury Lamp ^-^ Sessile Drop ¦=• Condenser c=> Microscope l_*~_i bJ Mlcromster Filer with Protmcter Fig. 1—Schematic diagram of apparatus set-up for liquid contact angle measurement.

Jan 1, 1970

F A. THOMSON, president of the Montana School of Mines, gave an interesting talk on mining schools of the past, present and his ideas of the future before a recent meeting of the Montana Section of the A. I. M. E. He covered the history .of the various mining schools and com- pared the three main types of schools; those attached to or forming part of an endowed college or university such, for example, as' the Columbia School of Mines, the Mining Department of the Massachusetts Institute of Technology and the Mining Department of Stanford University. These resemble in a general way the second class, those attached to the state universities and colleges. The schools of this general type have had varied success.

Jan 1, 1928

By Frank Haas

Many articles on the physical properties of fire damp have appeared in the Transactions and elsewhere but practically nothing has been written in regard to its occurrence or fluctuation in quantity in an ordinary mine. After the Monongah explosion in 1907, with the loss of 361 lives, the Consolidation Coal Co. sought a method by which such catastrophes could be prevented. While the cause of this particular explosion was attributed to coal dust, some of those acquainted with the mine thought that fire damp was involved, if it was not the initial cause. So the literature on the subject was studied and mines where similar conditions prevailed in this country and Europe, were visited, with the view of establishing some system by which gas could be more easily detected and controlled. The results of this study were disappointing for no method was found other than the time-honored fire boss with his safety lamp, with some variations in the rules and regulations governing his inspections and reports. Duties of the Fire Boss Pending the development of a better method, it was decided to standardize and perfect the duties of the fire boss and the reports based on his observations. Those who were then in service were closely examined, various lamps were experimented with and the lamps and individuals tested under known conditions. It was found that a fire boss could tell whether gas was present but his estimate of quantity was not even an approximation; therefore, while the services of fire bosses were indispen-sible there was need of additional information by which the quantity of gas could be estimated with some precision in order to determine its variation from time to time. Chemical Process for Determination of Methane After considering all methods known at that time a chemical process was adopted. The principles involved in the process are that in an enclosed receptacle, in the presence of excess air, methane will be completely burned by means of a hot platinum wire to carbon dioxide and

Jan 1, 1927

By J. J. Sense

This paper deals with the Asarco method for the determination of equipment availability. It is apparent that no single availability equation will provide all of the information necessary for the complete record of equipment availability. In the Asarco system, three separate availability records are carried on major equipment. The first is mechanical availability, the second is operational availability, and the third is a historical record of equipment use. The derivation of the three items and the definitions of the time elements used in the various availability equations are presented and discussed. The Mission unit of American Smelting and Refining Co. is located in Pima County, Ariz., approximately twenty miles southwest of Tucson. The unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to company smelters at Hayden, Ariz., or El Paso, Tex. Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tpd concentrator was started in the spring of 1960. The first ore was treated in midsummer of 1961 and full ore production was reached in August 1961. At that time over 46 million tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tpd. Total production to date (ore and waste) is over 120 million tons. Major equipment currently in operation at the Mission pit is as follows: 3 P & H 1800 Electric Shovels - 9 cu yd dippers 1 P & H 1900 Electric Shovel - 9 cu yd dipper 2 B.E. 190-B Electric Shovels - 9 cu yd dippers 35 Euclid LLD Trucks - 60-ton capacity 6 KW-Dart 55-T Trucks - 55-ton capacity 1 KW-Dart D-2550 Truck - 65-ton capacity 1 LeTourneau Westinghouse 65 Haulpak - 65-ton capacity 3 Euclid S-18 Scrapers - 274011 capacity 4 Caterpillar D-8 Dozers 4 LeTourneau Westinghouse Tournadozers 1 Michigan 280 Dozer 2 Caterpillar Model 12 Motor Graders

Jan 1, 1964

By AIME

AS the Petroleum Division rounds off the first quarter century since its evolution from technical committee status, there steps to the long line of notable men who have presided over its activities a young man, currently of Tulsa, one Herbert F. Beardmore by name. For one year, as Chairman for 1946, the Division will be his oyster. hi; baby, his responsibility. "Herb" Beardmore was born at Columbus, Ohio, Feb. 6, 1904, and lived there until he was thirteen. Then his family moved to Oklahoma City, and later sent him to the University of Oklahoma, where he graduated in 1925 with a B.S. in engineering geology. His final year in college was the first year in which a petroleum engineering course was taught at the school. Since his course of study so closely paralleled that of a petroleum engineer, he has frequently been spoken of as the first petroleum engineering graduate from the University of Oklahoma. Out of college he went to work as an oil-field roustabout in the Ranger, Texas, field for Jake L. Hamon. This work consisted of all manual labor phases of cable-tool operation and beam-pumping of oil wells. He moved in 1926 to Bartlesville, to become a gas engineer for the Indian Territory Illuminating Oil Co., where he was employed in gas-well drilling, gas production, and transportation, mostly in Osage County, Oklahoma.

Jan 1, 1946

By Edward B. Cook

INTRODUCTION. THE installation of the Gayley Dry-Air process appealed specially to the management of the Warwick Iron & Steel Co., for the. reason that for fifteen years records had been kept at the works of the company, showing the amount of water entering the furnace in the form of aqueous vapor, and careful observations had been made of its effect upon the working of the furnace. Some years had proved much worse in their effect than others, on account, not only of excessive moisture, but also of great variation in the moisture from day to day, and sometimes within a few hours. It had been found impossible to. make a satisfactory percentage of high-silicon foundry-iron in summer, even on high fuel; and for some years the endeavor had been made so to arrange the sales that, during July and August, only a small percentage of the iron produced would be required to carry more than 2 per cent. of silicon. Our larger furnace, running on basic iron, year after year, produced in February a tonnage 20 per cent. higher than in August, on a much lower fuel-consumption, while, at the same time, the summer months were marked by ? messes," tuyeres closed by slips, and other irregularities, constituting serious additional business losses. It will be easily understood, therefore, that the records made at the Isabella furnace after the installation of the dry blast in 1904 possessed special interest, and were closely watched by us. On the basis of our own experience, we argued that if the moisture could be kept low, and also uniform, the cost of installation would be more than justified. The subject was brought before our Board of Directors in the fall of 1905; and in the spring of 1906 it was decided to install a plant of sufficient capacity to treat 70,000 cu. ft. of air per min., an amount

Nov 1, 1908

A new departure of unusual importance in Institute annals was in-augurated by the trip of President Philip N. Moore to the Local Sections at Nevada, Southern California, San Francisco, Seattle, Spokane, Montana, Utah, and Colorado. Everywhere the visit of the President was the occasion of an enthusiastic and successful meeting, which is reflected in the account, published under the different Sections in this and other Bulletins. The President also joined the members of the Columbia Section in their visit to Nelson, British Columbia, at the International Mining Convention, which was attended by mining engineers of Canada and the United States. The President of the Canadian Mining Institute, as well as the officers and members of the Western Section also attended this convention. For full particulars we recommend to our readers the ac- count of this very interesting meeting, which is given on another page of this. Bulletin. It is believed that this is the first meeting between the mining engineers of America and any other country since America joined the Allies. The Secretary of the Institute accompanied the President at the first four meetings and was expecting to attend the others also, but was called home by a death in his family.

Jan 7, 1917

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By J. B. Cohen, S. L. Sass

The nucleation process for y', Ni3Ti, is shou'n to change from heterogeneous to uniform as the undercooling within the phase boundary increases. As unifornz nucleation beconres copious, (100) alignment is observed in the early stages of aging; howecer. whether or not the alignment is due to spinodal decomposition could not be determined. The presence oi a large-scale reversible segregation of titanium and not the intermediate precipitate y' may be the cause of the initial strengthening in this alloy system and the discrete regions detected magnetically by Ben-Israel and Fine. Evidence is presented for the role of dislocations in the formation at long aging tines oJ the equilibrium precipitate . ThE nickel-rich portion of the Ni-Ti phase diagram consists of a terminal fcc solid solution of titanium in nickel called y.' For temperatures below 1290°C if the solubility limit is exceeded and the temperature is high enough, the excess titanium will combine with nickel to form q, Ni3Ti, a four-layer hcp ordered structure with stacking sequence ABAC."~ Since a change in structure is involved, formation of q is slow and a metastable precipitate referred to as y' forms. This metastable precipitate is an ordered cubic phase in the unconstrained state having a structure similar to Cu3Au (LIZ) with the composition Ni,Ti."'5 From X-ray studies,8, 7 the following sequence is indicated for the precipitation reaction at low temperatures: 1) The appearance of satellites around low-index diffraction spots and splitting of high-index spots, indicating the formation of a slightly tetragonal phase in an imperfectly periodic arrangement. The tetragonal phase is y' or the depleted matrix, depending on the volume fractions of matrix and precipitate (and hence, the alloy composition); tetragonality apparently arises from coherency strains. 2) The appearance of diffraction spots from the equilibrium second phase, q. Ben-Israel and Fine'" used magnetic methods to measure the changes in matrix composition during aging, and to estimate the precipitate composition in a Ni-10.1 at. pct Ti alloy. They observed that the alloy, solution-treated at 1270°C and quenched, contained heterogeneities with discrete compositions which gradually vanished upon aging. It was suggested that y' may initially form as a defect structure with several possible compositions deficient in titanium as compared to Ni3Ti; the composition Ni3Ti develops with prolonged aging. The initial composition was Ni6Ti which would require a very large deviation in stoichiometry for y'. It was noted that at 700°C the precipitation reaction was 80 pct complete after 2 hr and that the volume fraction of second phase was 0.2 after 1 hr. Mihalisin and Decker' suggested that the equilibrium precipitate, besides being nucleated at grain boundaries, could also form at stacking faults. ~errick" examined the formation of in Ni-Cr-Ti, and suggested that a collapsed vacancy cluster within y' acted as a nucleus for intragranular q at high temperatures, 820" and 900°C. After long aging times at lower temperatures, 650" and 750°C, diffraction patterns taken from regions containing ribbons of stacking faults showed spots associated with q. Aging greatly enhances the mechanical properties of these alloys, even at high temperatures, and the metastable precipitate y' is thought to be responsible.' At 600°C the hardness of a Ni-10.1 at. pct Ti alloy increases rapidly during the first 20 hr of aging and continues to increase slowly thereafter.'" At 700°C the hardness reaches a maximum at 1 to 2 hr and then decreases.l1 In this paper the kinetics of formation of y' and the mechanism of transformation to in a Ni-Ti alloy are described. Evidence is presented that suggests that large-scale regions of titanium segregation are present initially and these may have an important influence on the initial strengthening of the alloy: these regions may be the heterogeneities detected by Ben-Israel and Fine. I) EXPERIMENTAL TECHNIQUES The Ni-10.3 at. pct Ti-0.6 at. pct A1 alloy was prepared by vacuum melting. Its chemical analysis is given in Table I. A 0.007-in.-thick strip was sandwiched between foils of the alloy and placed in an open Vycor tube with titanium chips (to get oxygen) and solution-treated for ; hr at 1150°C in a Globar Furnace under a flowing argon atmosphere. Following a quench into an ice-brine mixture at -5" to -2"C, a sample to be aged at temperatures up to and including 700°C was sealed in an evacuated Vycor capsule before being put into a fused salt bath. Aging above 700°C was carried out on bare samples in a salt bath. When removed from this bath and quenched into an ice-water mixture, the sample was normally coated with a thin layer of oxide easily removed with emery

Jan 1, 1970

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

By H. L. Luo

SYSTEMATIC investigations of the Fe-Ga system have been reported only very recently."' The maximum solid solubility of gallium in a-Fe is nearly 50 at. pet at 900°C. However, from Ref. 1, it was not evident that the a-Fe solid solution could be retained successfully beyond 17.38 at. pet Ga by solid-state quenching. The present investigation reports the retention of a-Fe solid solution at 50 at. pet Ga by quenching from the liquid. An ordered phase of CsC1-type B2) structure was observed between 34 - 50 at. pet Ga. Since it was considered very probable that the CsCl structure would occur at high temperatures, alloy filings were also quenched by the conventional quenching technique. In addition to the CsCl phase, a second ordered phase of BiF3-type (DO3) structure was found in the range 25 - 30 at. pet Ga. Alloys were prepared from elements of 99.99 pet purity or better, induction-melted in alumina crucibles under hydrogen. After reweighing, the alloy ingots were cast into wires under argon. From the weight losses and the reproducibility of the lattice parameters, compositions were estimated to be within ± 0.3 at. pet. The techniques of quenching from the liquid state were reported before.3-5 Prior to quenching, a small section of cast alloy wire (30 - 50 mg) was melted in an alumina insert under an argon flow. The quenched specimens were in the form of flakes, typically 1 sq mm in area. For solid-state quenching, alloy filings passing 200 mesh were sealed under a reduced helium atmosphere in a thin-bottom silica tube. After heating for -30 min at the desired temperature in a vertical furnace, the sealed tube was rapidly dropped into ice water so that the thin bottom of the tube broke on impact. The quenched alloy filings were always ferromagnetic and could be collected by a magnet. X-ray diffraction patterns were taken with iron-filtered cobalt radiation in a 114.6-mm-diam Debye-Scherrer camera. High-angle lines were always resolved and spacings were computed relative to ? (CoKa1) = 1.78890Å. Lattice parameters were obtained from extrapolation against the Nelson-Riley function. The variation of lattice parameter with composition is shown in Fig. 1, together with the data of Dasarathy and Hume-Rothery.1 Uncertainties in the present measurements are within the dimensions of the symbols or indicated by error bars. X-ray diffraction lines indicative of CsC1-type ordering could be clearly identified for alloys of 34 - 50 at. pet Ga quenched from the liquid and alloys of 35 - 41 at. pet Ga quenched from -975°C. Within experimental error, no difference in

Jan 1, 1968

By M. W. Von Bernewitz

AN important regional meeting of the American Institute of Mining and Metallurgical Engineers was held, at Salt Lake City on Aug. 22 to 26, jointly with the fifth annual meeting of the Western Division of the American Mining Congress. The whole meeting was marked by enthusiasm, keen attention to the subjects under discussion, and many renewals of personal contacts. The trips to the various plants were well attended and the local press paid much attention to the meeting. The A. I. M. E. sessions began Aug. 23, with a non-technical morning session. J. 0. Elton, manager for the International Smelting Co., presided. The purpose of this session was to present in a non-technical manner the relation of flotation to mining, smelting, and the State. Ernest Gayford, metallurgist with the General En-gineering Co. of Salt Lake City, gave the definitions of flotation as suggested by Rickard, the dictionary, Weinig, and Taggart. The active agent in flotation is the air bubble, and the two prime requisites are the formation of bubbles and the creation of selective action of the bubbles for metallic particles instead of for gangue particles. Broadly, all the sulfides are floatable minerals, but the oxides, carbonates, silicates and sulfates are not. As far as Utah is concerned, flotation has been one of the greatest means of conserving its natural re-sources, because it has converted millions of tons of waste rock into pay ore; it is recovering millions of pounds of metal formerly lost in tailings; it has con-verted the zinc from a liability into an asset; and has kept thousands of men at work and distributed millions in dividends for the benefit of the State. As to the future of flotation, Mr. Gayford can con-ceive that the next 5 or 10 years may see as much, if not more, advance than was made in the preceding period. The big problem is dressing oxides, carbonates, silicates, and sulfates, and simplification of the number of reagents, also the separation of different gangue min-erals from one another.

Jan 10, 1927

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946

By E. P. Klier, Jane Jellison

The course of the transformations on cooling in a series of Cu-A1 alloys has been followed by means of thermal analysis, X-ray diffraction, and optical metallogrAphy. Specimen size was found to have a pronounced effect on the time of completion of the pearlite transformation due to modification in the unmber of nuclei. The ordeving transformation zvas observed for all cooling rates for all alloys studied, and is considered insuppvessible. At intermediate cooling' rates, a transitional struchire for 011 alloy compositions and based ox the bainite reaction was observed. The alloys of aluminum and copper possess a eu-tectoidal region at from about 9.4 to 16 pct Al. Above the critical temperature, the disordered bcc phase, 0, is stable. At subcritical temperatures, the 0 phase decomposes under equilibrium conditions into the stable phases, a and y,. At the eutectoid composition, these phases develop a lamellar pearlite structure, in appearance much like that found in steels. During rapid quenching from supercritical temperatures, the diffusion processes required for the formation of the equilibrium phases are suppressed, and the 0 transforms to an acicular martensitic phase, designated B or y' depending on the aluminum content, or to a mixture of the two. Early investigators of this system concentrated on determining the equilibrium phase diagram, ''' the structure of the equilibrium phases,3 and later the isothermal decomposition of the 0 phase at subcritical temperatures, or the decomposition of the martensite on tempering. Other work which treated the nonequilibrium transformations concentrated largely on the martensite transformations and the structure of the b and y' phases.15"17 Since the pearlite and martensite transformations in this system resemble those in steels, the one being formed by nucleation and growth of adjacent lamellae of the equilibrium phases, and the other by a diffusionless, shear-type transformation, the present study has been undertaken to investigate the structures formed on continuous cooling, with the objective of constructing cooling transformation diagrams analogous to those derived for alloy steel systems. In particular it was desired to determine whether parallels between the A1-Cu and iron-iron carbide systems on continuous cooling extended to encompass the intermediate phase, namely the bainite structures, which form by a combined martensitic-diffusion mechanism,'' but which are supersaturated with respect to the equilibrium phase upon which their crystal structure is based. To this end the transformations in representative alloys of the Cu-A1 B eutectoid system have been followed, using the methods of thermal analysis, X-ray diffraction, and optical microscopy. EXPERIMENTAL PROCEDURE Materials. The materials tested were those used by Klier and Grmko 5 in their study of the isothermal decomposition of these alloys. The alloys were melted in graphite crucibles and chill-cast into 5 by 2 by 1/4 in. ingots. The ingots were then hot-rolled to sheets 1/8, 1/16, and 1/32 in. thick. The compositions are given in Table I. Specimen Preparation. Specimens for thermal analysis were in the form of small squares approximately 1/4 in. on a side. For the 11.9 and 13.5 Al-Cu alloys, the sheet thickness was 1/16 in. and for the 10.5 A1-Cu alloy the 1/32-in. sheet was used. One lead of a chromel-alumel thermocouple was spot-welded to either face of the square with the specimen itself thus forming the hot junction of the thermocouple. Specimens for X-ray analysis were prepared as filings from martensitic sheet stock and were sealed in glass ampoules under 1/2 atm of argon. Metallographic examination of the powder specimens was carried out on a portion of the heat-treated filings mounted in lucite. All specimens were examined metallographic ally after etching

Jan 1, 1965

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By E. C. IBBOTSON

THIS process was reported upon by the Canadian Commission in 1904, and much detailed information was also given in a paper by Chief Engineer V. Engelhardt.1 Believing that some of the latest particulars of the process will be of interest, I submit the following data. At Gysinge in Sweden during the year ending May 31, 1906, from a fixed furnace giving 1 ton (2,240 lb.) of steel per tap, there were produced 950 tons of tool-steel and special steel ingots. . In carbon and iron tool-steels all the usual tempers were made. The bulk of this steel was made from charges composed of about 80 per cent of Swedish white pig-iron and 20 per cent. of steel-scrap. The percentage of carbon was regulated by the addition of briquettes. Other charges were made from Swedish white iron and steel-scrap. The average time taken per charge, for the year, when adding briquettes, was 7* hr., and the electric energy consumed was 1,128 units (kilowatt-hours) per ton. The average time per charge for white-iron and scrap charges was 5.5 hr., and the electric energy consumed was 886 units per ton. These consumptions include all time and energy lost from various causes, such as bad water-supply, ice, etc. It is quite ordinary practice to complete the charges with briquettes in 6.5 hr., and without briquettes in 5 hr., as shown by the following typical charges White pig-iron, 1,457; steel-scrap, 439; briquettes, 220; ferrosilicon (50 per cent. of silicon), 17 ; ferromanganese (80 per cent. of manganese), 15 lb. ; and aluminum, 1 oz.=

Nov 1, 1906