Search Documents

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel's paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel's attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,', y uranium, and perhaps zirconim.' The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors' reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato's value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,'' and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener's predictions.28 We have no quarrel with Hagel's placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By Carl Wagner

This paper contains solutions of the differential equation of diffusion in binary alloys if the diffusion coefficient is an exponential function of the concentration of one of the components. THE general differential equation for one-dimensional diffusion in a binary system can be written as: where c is the concentration of one of the two components in any suitable units; x, the distance from a reference plane; t, time; and D, the diffusion coefficient. Hartley and Crank&apos; have pointed out that eq 1 with conventional length units for measuring the distance x holds only if the alloy can be regarded as a rigid framework. In general, this is not the case, especially if the lattice parameter varies appreciably with composition. If a modified coordinate system is used instead of an orthodox system based on the centimeter a:: length unit, eq 52 is obtained, which has the same general form as eq 1 and is generally valid. The necessary transformations are presented in the appendix. If&apos; D is independent of concentration, analytical solutions of eq 1 are known for numerous boundary conditions. If D depends on concentration, solutions based on known analytical functions are not available. Among others, Boltzmann2 and Matano3 have shown that the concentration c depends only on (x/t1/2) in the case of diffusion between two semi- infinite spaces with uniform initial concentrations: c = c, for x < 0, t = 0, i.e., x/tl/2 = — x [21] c = c2 for x > 0, t = 0, i.e., x/tl/2 = + a Moreover, Boltzmann and Matano have shown how D may be calculated as a function of concentration over the whole range of composition from c -c, to c = c2 if c as a function of (x/t1/2) for the initial conditions stated in eq 2 has been determined experimentally. Thus, for instance, in principle, the diffusion coefficient in silver-gold alloys may be calculated as a function of concentration for the whole range of composition from only one diffusion experiment with a couple of pure silver and pure gold welded together. If the diffusion coefficient D as a function of concentration c is known, a solution of eq 1 for boundary conditions as stated in eq 2 with arbitrarily chosen values of c, and C2 may be wanted. For instance, if the diffusion coefficient in an alloy A-B as a function of concentration has been derived from an experiment with a diffusion couple involving 0 and 30 pct B as initial. concentrations, the calculation of the concentration distribution in a diffusion couple involving other initial concentrations, e.g., 5 and 20 pct B, may be desired. This problem may be solved by numerical or graphical integration of eq l. The solution of an ordinary differential equation of second order, which results from using (x/t1/2) as an independent variable, can be computed quite rapidly if two conditions for the same value of the independent variable are given. In eq 2, however, two conditions are given for two

Jan 1, 1953

By John J. Gilman

F many years it has been suspected that a correlation existed between pits produced by etching and the density of dislocations in crystals. In 1953, the interest in this correlation was greatly stimulated when Vogel et al&apos; demonstrated a 1:l correlation between etch pits and dislocations in low angle grain boundaries of germanium. About two years ago, the author began attempts to produce etch pits at dislocation sites in zinc mono-crystals. These attempts met with success a year or so ago,&apos; and since that time a survey has been made of the etch pit patterns that are associated with various modes of deformation in zinc monocrystals. Unfortunately, the etching technique that will be described is too delicate for use as an accurate quantitative tool. Nevertheless, it has been of considerable assistance in clarifying the structure of plastically deformed crystals. Technique Many attempts were made to produce etch pits in high purity zinc crystals. It was found that several techniques would produce surface grooves at grain boundaries that had misorientation angles greater than about l°, but no technique was successful for boundaries with smaller angles. Among the things that were tried were: electrolytic CrO, (both etching and polishing concentrations), HNO, in various water and alcohol solutions, dilute HC1, many 0-0,-Na,SO, solutions, Cr0,-HC1 solutions, picral, electrolytic Na,S,O,, and electrolytic NaOH and KOH. A few attempts to use cathodic sputtering and thermal etching were also made.

Jan 1, 1957

By Walter E. Hopper

(Wilkes-Barre Meeting, June, 1911.) I. LOCATION AND EXTENT. THE Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five rail-road-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. II. HISTORY AND DEVELOPMENT. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser " Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905, four wells were drilling. Great trouble was experienced with

Apr 1, 1911

By William E. Ford, Edward Salisbury Dana

5. Crystallography. - The subject of Crystallography includes the description of the characters of crystals in general; of the various forms of crystals and their division into classes and systems; of the methods of studying crystals, including the determination of the mathematical relations of their faces, and the measurement of the angles between them; finally, a description of compound or twin crystals, of irregularities in crystals, of crystal- line aggregates, and of pseudomorphous crystals. 6. Definition of a Crystal.- A crystal * is the regular polyhedral form, bounded by smooth surfaces, which is assumed by a chemical compound, under the action of its intermolecular forces, when passing, under suitable conditions, from the state of a liquid or gas to that of a solid. As expressed in the foregoing definition, a crystal is characterized, first, by its definite internal molecular structure, and, second, by its external form. A crystal is the normal form of a mineral species, as of all solid chemical com- pounds; but the conditions suitable for the formation of a crystal of ideal perfection in symmetry of form and smoothness of surface are never fully realized. Further, many species usually occur not in distinct crystals, but in massive form, and in some exceptional cases the definite molecular structure is absent. 7. Molecular Structure in General.- By definite molecular structure is meant the special arrangement which the physical units, called molecules, assume under the action of the forces exerted between them during the formation of the solid. Some remarks are given in a later article (p. 22 et seq.) in regard to the kinds of molecular arrangement theoretically possible, and their relation to the symmetry of the different systems and classes of crystals.

Jan 1, 1922

By C. J. Sparks, J. C. Ogle, E. A. Starke

DEFORMATION of cold-rolled fcc metals and alloys produces one or the other of two types of rolling textures, usually referred to as the copper type or the brass type. The pure fcc metals, with the exception of silver, develop the copper-type texture when rolled at room temperature. Silver, brass, and many other alloys develop the brass-type texture. Transition from one texture type to another can also occur. Solute additions to pure copper cause a transition from the copper-type to the brass-type texture.&apos; Varying the deformation temperature also produces texture transitions. Copper rolled at -196°C developed the brass-type texture2 and silver rolled at elevated temperatures, 200°C, developed the copper-type texture.374 The work of Haessner,&apos; Smallman and Green,6 and Hu and coworkers3&apos;4 seems to have established an apparent correlation between the type of rolling texture (and the texture transition) and the stacking-fault probability. Thus materials with low stacking-fault energies are thought to develop the brass-type texture while high stacking-fault energy materials develop the copper-type texture. Mikkola and cohen7 measured by X-ray diffraction techniques the stacking-fault probability, a, in the ordered and disordered fcc alloy Cu3Au. Unexpectedly, ordered specimens showed about twice the stacking-fault probability as the disordered ones. Marcinkowski and Zwe118 also found stacking faults in ordered Cu,Au, but not in the disordered CusAu. More recently, Camanzi and coworkers9 have shown that the intrinsic stacking-fault energy of Cu3Au undergoes a considerable decrease (approximately 100 ergs per sq cm) when passing from the disordered to the ordered phase. In general, deformation reduces order&apos;&apos; but some of our measurements showed that some long-range order still remains in Cu3Au after cold reduction by rolling 80 pct. From the above considerations Cu3Au offers the possibility of studying the texture transition in fcc alloys without varying either the temperature or the composition. If the stacking-fault energy correlation is correct, an initially ordered alloy should develop the brass-type texture during rolling while a disordered alloy should develop the copper-type texture. The present communication describes some initial results of experiments designed to investigate this possibility. The rolling textures of ordered and disordered Cu3Au samples were determined after various amounts of deformation. The ordered sample had an initial long-range-order parameter of S = 1, determined from X-ray diffraction. The grain size of both the ordered and disordered samples was the same, and the initial textures of both were also identical and approximately random. No obvious differences in the deformation textures of the ordered and disordered materials were detected up to 35 pct reduction and the (111) pole figures of Fig. 1 resemble that of pure copper. However, with reduction larger than 35 pct and less than 50 pct, a marked deviation from the copper texture was noted in the ordered material. The newly developed orientation was close to the (110)[i12] ideal orientations re-

Jan 1, 1970

By Rana P. Singh

Electrolytic metal reduction operatios in both aqueous and molten salt electrolytes are being studied by digital signal analysis. The purpose is to determine the relationship between the physical processes occurring in the cell and the frequency spectrum of the cell&apos;s fluctuating electrical parameters. The fast Fourier transform of cell voltage (in galvanostatic operations) or cell current (in potentiostatic operations) is computed on-line in real time for the electrorefining of zinc in aqueous acid chloride solutions.

Jan 1, 1984

By K. Tangri, B. Swaroop

Simultaneous measurements of lattice (elastic) strain by X-ray line shift method and total strain with an electrical strain gage have been carried out on polycrystalli,ne nickel with the help of a specially designed tensometer attachment for the X-ray dif-fractometer. During the initial stages of deformation, the rate of increase in lattice strain closely follows the total strain until the plastic strain sets in. From then onwards, the two strains deviate from each other and with further increase in afiplied stress the rate of increase of lattice strain eventually decreases. Depending upon the mode of unloading, both compressive and tensile strains have been observed in nickel deformed up to 0.29 pct strain. These results have been explained on the basis of the effects of clustering of dislocations and also the production and behavior of point defects during loading and unloading, respectively. POLYCRYSTALS deformed plastically in a uniaxial tension test show residual lattice strains (hereafter referred to as RLS), which broaden the X-ray line profiles and shift their peak positions.&apos;&apos;4 It is known that uniform straining of a crystal lattice (macrostrain) produced movement of ddfraction line peaks, whereas nonuniform straining (microstrain) causes line broadening.= Though the nature and origin of RLS in deformed metals is not yet clearly understood, these are believed to be due to the presence of some form of a locked-up stress system. Several possible detailed interpretations6&apos;" of the stress system have been proposed by various workers and common to all these interpretations is the assumption that different parts of the aggregate have different tensile yield stresses; e.g., that a part A yields under a lower applied stress than a part B. Therefore, during the deformation process, the elastic strain in A will be less than that in B, and, after completion of deformation, B will tend to contract further than A but will be prevented from doing so by the restraining influence of A. Thus, when equilibrium is reached, A will be in compression while B is in tension. Although there is general agreement on the correctness of this argument, controversy still exists as to the exact nature of the parts A and B in a deformed metal. In an alternative approach to the creation of parts A and B, many other investigators have assumed that the RLS observed in unloaded specimens are in some way connected with the lack of proportionality between lattice strain and applied stress in the region above the yield stress." cullity13 has prepared a schematic summary of the results of previous workers, mainly Smith and Wood,2&apos;11 which suggests that, above the elastic limit, the lattice strain may increase less rapidly with respect to strain, or may even decrease with increase in applied stress. If the applied stress is then decreased, the lattice strain would decrease along a line parallel to the loading line in the elastic region and thus produce a compressive residual lattice strain after unloading. At equilibrium, to balance these compressive stresses? there would have to be regions under tensile stress which may well be the grain boundaries or the substructure walls formed during deformation. The present investigation was undertaken to gain a better understanding of the nature and origin of RLS and also to experimentally verify the salient features of this hypothesis. EXPERIMENTAL Stress and strain determinations were made with a specially constructed tensometer attachment for the X-ray diffractometer, Fig. 1: which permits the following measurements simultaneously on a sheet specimen under uniaxial tension at various stress levels during loading and unloading: a) lattice strains, E=. in a direction perpendicular to the direction of pulling (x direction) from shifts in X-ray line peak positions; b) the total strain, ex, in the direction of pulling. with the help of an electrical strain gage affixed to the back of the specimen directly below the area irradiated by X-rays: and c) the applied stress, with the help of a load cell which consisted of a calibrated stainless-steel sample of dimensions identical to those of the specimen under investigation, and to which it was coupled. Because of its high stacking fault energy.I4 nickel

Jan 1, 1970

By ROBERT R. ABUOTT

Discussion of the paper of Prof. Albert Sauveur and, G. A. Reinhardt, presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1335 to 1341. ROBERT R. ABBOTT, Cleveland, Ohio :-The possibilities of the commercial application of the facts brought out in this paper have been the subject of many experiments by me during the past four years. It will be well to call attention to several facts having a commercial bearing upon the problem: (1) The lower critical temperature (Ac) of a 3.5 per cent. nickel-steel of low carbon (say 0.20 per cent.) content is about 710° C. This is not lowered to any extent by increasing its carbon content by carbonizing,. By this I mean that a steel with Act occurring at 710°, must, after carbonizing, be heated above this temperature before quenching in order to make it hard. This is not contrary to Guillet&apos;s diagram, although at first thought it may seem so, due to a confusion of the Act and the Ar1, points. His diagram merely gives the physical condition of the steel upon slow cooling. Now a steel of 1.20 per cent. of carbon and 3 per cent. of nickel (point " B " of the diagram) may be martensitic upon slow cooling from three causes: (a) Its Ar1 point is below the normal atmospheric temperatures. (b) The time element is so important that the change from martensite to pearlite and cementite does not have time to occur even with this slower rate of cooling. We of course know that nickel has the tendency of retarding this change. (c) A combination of the above two causes. (2) With increasing nickel content the ability of steel to absorb carbon decreases. (3) Many carbonized nickel-steels show a martensitic. structure upon air-cooling, and yet ire so soft that they are of no commercial value.

Dec 1, 1912

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By Richard McCaffery

WHEN we began the study of blast furnace slags we limited our work at first to a study of those slags containing only lime, alumina and silica. On our paper1 on some of the results of this first work, the solubility of sulfur in slags containing no magnesia was reported and the question of sulfur solubility and slag viscosity discussed. There has been, for a long time, a very great difference of opinion among metallurgists as to he effect of magnesia in blast furnace slags, and the literature is full if expressions of the most contrary opinions on the subject. As a result, our next publication&apos; developed the constitution of slags considered as a four-component system, silica-alumina-lime-magnesia, and advanced an explanation of slag structure which accorded with the facts and with scientific theory. The present paper continues our study of the general subject of slags. As blast furnace slags are included in the silica-alumina-lime-magnesia system, which is a particular case of four-component solutions, we have determined that there are 22 components Table 1), which may enter into the silica-alumina-lime-magnesia system and that 10 or 12 of these components may be present in blast furnace slags which are within the ordinary ranges of composition. To cave a very definite conception of the behavior of these components in a slag, we have developed the theory of the cooling of a four-component solution from the liquid state to the solid and the conclusions that we obtained have been made use of in this paper. On account of the importance of the four oxides and 18 compounds which enter into the silica-alumina-lime-magnesia system, some method of calculating the percentages of the various compounds that are present in the slag when the percentages of the oxides are given, seemed very desirable and we develop L method later herein for doing this, and finally we give illustrations of the composition of a wide series of blast furnace slags and show some applications of these composition data.

Jan 1, 1927

By Ravitz, S. F

76-B Unpublished manuscript. Not available in printed form. An experimental and Theoretical investigation of Quantitative Microscopic Mineralogical Analysis. By S.F.Ravitz and H.A.Steane. Manuscript in Engineering Societies Library.

Jan 1, 1935

THE third annual Joint Western Mining Convention, held at Los Angeles, Sept. 10 to 13 inclusive, was a notable success both as to attendance and interest. Registration the first day amounted to 201, and the total crept up to 347 before the close. The American Institute of Mining Engineers was well represented, approximately 80% of those registered and most of the speakers being members. This illustrates largely the amount of interlocking membership and the reason for holding at one time and place meetings of the several related organizations. The plan has proved so successful that it is probable that Spokane will extend an invitation for next year that seems likely to be accepted. It is proposed that the convention be timed so as to permit visitors from the East to stop there Oct. 3 to 5, en route to the American Institute of Mining Engineers meeting at San Francisco, Oct. 7 to 9. Simultaneously, it is expected that the Petroleum Division will hold its fall session at Los Angeles, the two streams of travel meeting in San Francisco, just before departure of the party of engineers traveling to Japan to attend the World&apos;s Engineering Congress. The Los Angeles meeting opened Monday morning with a general session under the auspices of the Western Division of the American Mining Congress with Philip Wiseman in the chair. After a series of short responses to the welcome extended, Charles W. Merrill discussed the needs of the western mining industry. A complimentary luncheon to members and delegates followed.

Jan 1, 1928

By Brian F. Osborne

A continuous on-line particle-size analysis system for solid/liquid suspensions is described. The basic sensor utilizes a centrifugal principle to separate particles according to size, the resultant separation being measured by means of beta-ray attenuation. Results obtained when analyzing a variety of materials at sizes from 65 mesh (210 µ) to 20 w are discussed in detail. Accuracies better than 2% are demonstrated. The effects of particle specific gravity, and mixtures of materials of diverse specific gravities, are discussed from both a practical and a theoretical viewpoint. It is demonstrated that particle specific gravity has a minimal effect on the size reading obtained. This renders the instrument suitable for handling materials where the ratio of light to heavy component may change. The design of the first commercial installation of this instrument is described in detail. This installation will be capable of analyzing three streams in sequence, measurement at three particle sizes being effected on each stream.

Jan 1, 1975

Jan 1, 1929

By Clark A. Sumner, D. Arthur Burnham

A process for recovery of greater than 99% of the copper contained in acid leach solutions by sulfide precipitation using hydrogen sulfide as a hydrometallurgical reagent has been developed. The process incorporates the concept of hydrogen sulfide addition to recycled copper sulfide solids in a turbulent flow area where further precipitation or agglomeration occurs to increase the effective particle size of the copper sulfide precipitate. Because the recycled solids provide a larger number of particles upon which momentary excesses of hydrogen sulfide are absorbed, oversulfidization of the product is prevented. Copper sulfide precipitates produced in this manner in a laboratory test reactor showed greatly improved physical characteristics compared to copper sulfide precipitates obtained by conventional direct precipitation in which H2S is bubbled directly into acid leach liquor. Copper sulfide precipitates were evaluated and compared by use of filtration tests and settling rate studies. Electron microscopic examination of the solids confirmed the presence of larger particles in reactor-precipitated copper sulfide. Flotation was examined as an alternative to filtration for recovery of CuS precipitates and was found to achieve complete CuS removal without addition of collector or frothing reagents in a period of 2 min. In the same test reactor, a rapidly floatable CuS precipitate was also formed by mixing H2S with acid liquors used to leach crushed copper oxide-copper sulfide ore (LPF process). In the presence of gangue from the crushed ore, flotation of both natural and reactor-produced copper sulfides resulted in recovery of better than 90% of the copper contained in the crushed ore.

Jan 1, 1974

By JOHN A. MALONEY

AS noted in the February issue of MINING AND METALLURGY, an advisory committee to the Museum of Science and Industry of Chicago was authorized by the Institute&apos;s Board of Directors, with W. R. Wright of Chicago, former Director of the Institute, as chairman. Since that time the committee has been undergoing organization, and held its initial meeting at the Museum offices in Chicago on April 11 and 12. Functioning as consultants to the Geology and Mineral Industries branch of this new institution, the advisory committee is aiding in building an exhibit which will tell the story of geology, mining, and metallurgy to millions of visitors a year. Although patterned to some extent

Jan 1, 1932

By William R. Chedsey

IN the last two years the E.C.P.D. committees having to do with the inspection of engineering schools for possible accrediting have been concerned with the engineering content of some of the mineral industries courses. Originally the discussion arose with regard to engineering geology, or geological engineering, afterward broadening to metallurgical engineering, ceramic engineering, agricultural engineering, and other branches not pertinent to this discussion. Some members of visiting committees took the attitude that they probably would have to accredit these types of training as included in the engineering group if they met the average standard set by the mining schools, though they questioned -whether they were really engineering.

Jan 1, 1939

Discussion of the paper of DAVID COLE, presented at the New York meeting, February, 1915, and printed in Bulletin No. 9S, February, 191.5, pp. 431 to 444. R. H. RICHARDS, Boston, Mass.-The Butchart riffle seems to violate, according to our preconceived notions, some of the very essential principles of the Wilfley riffle, and therefore ought not to succeed, but it does. On this account it must conform to other very important principles, or it would not succeed. It would beinteresting to know what these principles are which enable it to succeed. E. P. MATHEWSON, Butte, Mont.-I cannot, explain the principles on which this riffle acts, because I have not given it personal attention. All I can say is that I first saw the riffle in operation several years ago at the Steptoe Valley mill in Nevada, and I was told that a man had been around there guaranteeing that these riffles would make the table do twice as much work and do it better than with the ordinary Wilfley riffles. I heard nothing further about it for a long time. I heard about a year ago, from David Cole, the author of this paper, that the riffles were a success, and that he was using them at Morenci, and if, we were interested he would send the inventor to show us how they worked. As we knew of David Cole&apos;s reputation, we invited Mr. Butchart to come up and show us how his riffles worked. We did not have sufficient confidence in the invention to guarantee Mr. Butchart his traveling expenses, but lie came up entirely at his own expense and put in a set of the riffles on one table. It was known as a roughing table in our No.

Jan 5, 1915