Search Documents

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By Robert P. Burrows

Discussion of the paper of R. P. Burrows, presented `at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2237 to 2245. EDWIN M. CHANCE, Wilkes-Barre, Pa.-I have been very much interested in the comprehensive and able discussion of the important topic of mine lighting just given by Mr. Burrows, especially as I know by common report Mr. Burrows' ability and his close touch with the development of the electric mine lamp, and its use in mines in connection with a portable electric lamp. It is regrettable that Mr: Burrows was not able to acquaint himself more closely with the cost of mine illumination, the actual cost, as produced by a portable light as carried by miners, whether a flame safety lamp or an open light. Had he been able to acquaint himself more closely with these data, he perhaps would not have arrived at some of the conclusions which he has presented to us in his paper. For example, we find Mr. Burrows advises that the open torch is by far the cheapest source of illumination, as produced by a portable light. I am very sure that is not the fact. The cost of miners' oil varies from about 25.c. a gallon to 90b. a gallon. The various States have passed laws from time to time rendering it mandatory that the miner shall use, whether he is willing or not, a so-called better or higher grade of burning oil. These laws have entailed the use of an oil so expensive that the use of the oil torch has become practically impossible, and the acetylene or carbide miners' lamp has largely taken its place. I have evolved a few figures showing the relative efficiency and usefulness of the open oil torch and the acetylene miners' lamp. For example, the acetylene miners' lamp consumes or burns 4 liters of acetylene per hour, or 0.14 cu. ft.; the oxygen consumed is 10 liters, or 0.35 cu. ft. per hour; air consumed, 50 liters, or 1.76 cu. ft. per hour; black-damp produced, 40 liters, or 1.41 cu. ft. per hour; air rendered extinctive to the acetylene flame, 112 liters, or 3.95 cu. ft. per hour; carbide con- sumed, 13 g. per hour. The open oil torch, on the other hand, burns about 20 g. of oil per hour; the oxygen consumed is 48 liters, or 1.69 cu. ft. per. hour; air consumed, 240 liters, or 8.47 cu. ft. per hour; blackdamp produced, 191 liters, or 6.73 cu. ft. per hour; air rendered extinctive to oil flame is 1,413 liters, or 49.92 cu. ft. per hour.

Jan 5, 1916

By James Tucker MacKeni~ie

BORN in Florida, educated in Ten¬nessee, employed all his life in the iron industry of Alabama, J. T. MacKenzie is truly of the South. In courtesy, hospitality, as well as in accent of speech, he is true to the tradition of the South. His alma neater, the University of the South, has given him the honorary degree of Doctor of Science for his achievements in metallurgy. He has been active in many technical societies; has received the Whiting Medal of the American Foundrymen's Association for his work in the advancement of gray iron metallurgy, and is chairman of the gray iron division of the A.F.A.; was instrumental in initiating the Alloys of Iron Research of the Engineering Foundation and has served as a member of its Alloys of Iron Committee since the Committee's organization.

Jan 1, 1938

Executive ARTHUR S DWIGHT, Chairman B THAYER CHARLES F RAND P MATHEWSON J V W REYNDERS Membership WILLIAM H BASSETT, Chairman W Y WESTERVELT Vice-chairman P MATHEWSON H G MOULTON F T RUBIDGE Finance WALTER H ALDRIDGE, Chairman GEORGE D BARRON GALEN H CLEVENGER

Jan 1, 1923

By Edwin Ludlow

I DEEPLY appreciate the honor which has been conferred upon me by my election to the presidency of this Institute, as I feel that it is the highest honor a mining engineer can receive, and I also feel that I am especially fortunate in being called to take the presidency in the year following Mr. Hoover, as I may be enabled in that way to carry on the work which he has initiated. The constructive work that Mr. Hoover has inaugurated has been of inestimable benefit in bringing not only this Institute but the entire engineering profession into a place in the public esteem to a degree which it had never before occupied.. This work Mr. Hoover will now carry on in the broader field of the Federated American Engineering Societies, of which he is president. Through that organization the engineers of this country, in all branches of the profession, will be welded into one compact body reaching from the Atlantic to the Pacific, making the united engineering profession a power for maintaining American . . ideals and standards throughout the land.,

Jan 1, 1921

Arizona E. P. MATHEWSON, Chairman W. V. DECAMP. First Vice-chairman H. W. ALDRICH, Second Vice-chairman E. D. GARDNER, Secretary-Treasurer, Care U. S. Bureau of Mines, Tucson, Ariz. F A. AYES, J. P. HODGSON W L DU MOULIN WILLIAM KOERNER Boston Meets first Monday each winter month GEORGE B WATERHOUSE, Chairman GEORGE A PACKARD, Vice-chairman F. LEROY FOSTER, Secretary-Treasurer Room 8-219, Mass. Inst. of Tech , Cambridge, Mass. F K MORRIS F S MULOCK

Jan 1, 1923

By Ezequiel Ordonez

MOST spectacular of Nature's contributions to the making of the postwar world is the Paricutin volcano, in Mexico, which I described in the July issue of this magazine last year, a few months after it was born. Now, after more than a year of continuous eruption, it is still and perhaps will remain a comparatively small though no less interesting volcano. The cone on April 1 had an altitude of nearly 1200 ft. above the level of the small flat field from which it began to grow on Feb. 20, 1943. This cone is now almost entirely surrounded by the lava flows that poured out at different dates, from its base or from outlets on the slopes near its base. To the north and northwest these lavas were

Jan 1, 1944

THERE is at least one concrete indication that Soviet Russia's two most important iron ore producing centers are seriously depleted. While keeping in mind Russia's penchant for reverse propaganda, one piece of evidence indicates that Magnitugorsk in the southern Urals and Krivoi Rog in the Ukraine have been mined to a point where lower grade ores are being recovered. An article in Pravda, Soviet newspaper, by I. P. Bardin. a Russian metallurgist, says that ore presently mined must undergo an expensive enriching cycle before it can be used in blast furnaces. Com- pounding Russian metallurgical troubles is the low quality of coking coals. High ash and sulphur content typifies the coal Badin talks about. Coal from the Ukraine, Eastern Siberia, Kazakhstan, and the Far East requires extensive treatment before it can be used, according to the article in Pravda.

Jan 7, 1953

By N. H. MacMillan, O. C. Dias

Recent work by Westwood et al. (reviewed in Refs. 1-6) has established that many rocks, minerals, ceramics, and glasses exhibit phenomenologically similar chemomechanical (Rebinder) effects when deformed in different liquid environments, apparently as the result of chemisorption-induced variations in their near-surface flow and flow-dependent fracture behavior. In particular, it appears that there exists an empirical, but apparently general, correlation between the near-surface flow stress of an inorganic nonmetal and its surface charge- namely, that such a solid is hardest at its zero point of charge (i.e., when its zeta potential [ ] = 0) and softens as [ ] increases, regardless of the sign of zeta. Moreover, because near-surface flow and fracture phenomena are two of the important determinants of the rates of machining and comminution processes, both Westwood et al. and others7 have been able to use this so-called "[ ]-correlation" to develop cutting fluids and grinding aids that in many instances have given rise to several fold increases in performance. In addition, Westwood et al. have demonstrated that both aqueous and organic environments can give rise to similar improvements in cutting rate for a given combination of tool and workpiece, provided that both impart the same surface charge to the work- piece (i.e., transfer the same number of electrons to or from its surface). This last finding implies that in any application it should always be possible to find some cutting fluid that is at once effective, cheap, nontoxic, and nonpolluting. Thus, reports of apparently similar environmental influences on the mechanical behavior of diamond,8 certain organic crystals and polymers,9-14 and coa1-15-21 suggest that it is pertinent to ask: (a) whether the [ ]-correlation (or any analogous relationship) extends to coal; and (b), if so, whether this relationship can be used to guide the development of superior aids for grinding coal. Accordingly, correlations have been sought between (1) the zeta potentials, (2) the hardnesses, and (3 and 4) the drilling and grinding characteristics of coals of different rank in different aqueous and organic environments. This paper reports the results of that search.

Jan 1, 1980

By W. F. Boericke

NOT the least interesting sights that New York has to offer the visiting mining engineers are the extensive tunnel operations that are being pushed in connection with the subway construction. While a "hard rock" man might feel at home on these jobs, the engineers driving the subway tunnels have necessarily had to encounter some new problems pe-culiar to the largest permanent mining camp in the country. To drive a heading 36 by 18 ft. in hard rock, with a station section to follow 52 by 27 ft. across-and to do it in the midst of a city's traffic-demands engineering skill of a high order. Not the least of the problems overcome by the engineers in charge was to provide adequate ventilation for the men at the face at all times, so that there would be no delay in the work. With a crew of 40 men (32 drill runners and helpers on the machines alone, working two shifts) a hold-up due to inability to get back promptly to the face after shooting would affect costs quickly. AIR VITIATED BY EXHAUST FUMES FROM MOTOR TRUCKS A complication not encountered by metal miners, but which the subway engineers had to meet, was pollution of the air in the tunnels by fumes from the exhaust of the motor trucks used to haul away the broken rock. As shown in the cut, motor trucks were constantly em-ployed to remove the heavy tonnage broken as the tun-nels went ahead, amounting, according to R. J. Van Wagner, chief engineer of the Del Balso Construction Co., to 48 cu. yd. per ft. of tunnel advance. As the length of the tunnel under his management was 900 ft., it was essential for the safety of the men that suffi-cient air be introduced to dilute the poisonous fumes so that no ill effects would be felt for the entire distance that the trucks had to travel. The presence of the ex-haust fumes was especially noticeable on foggy days.

Jan 2, 1928

The University of Illinois, by Prof. H. H. Stock, professor of mining engineering, sent out to its mining students a long letter urging them to attend a Chicago meeting of the Institute. It stated that the University Council authorized the remission of the registration fee for sophomore, junior and senior mining engineers who would attend the meetings and present a written account of the sessions and excursions attended. Young engineers are rarely flushed at the beginning of their careers but if they ever expect to amount to anything at the end of 10-years-they are going to regret that they have not long been a member of the Insti-tute. So that the slogan "Do it now" is snore than particularly appli-cable in their cases and nothing will better indicate to them the scope of the Institute's work and the advantages which they are to get from mem-bership than attendance at one of the big meetings of the Institute and the preparation of a written report on the sessions and excursions attended to be returned to the University.

Jan 11, 1919

J. T. Pullon, Rowangarth, Roundhay, Leeds, England :— In discussing Mr. Lee's paper, I wish to call attention to the fact that Mr. B. II. Thwaite (who was heard here yesterday on the subject of the application of blast-furnace gas for the production of power, of which he was undoubtedly the pioneer) read, at the Engineering Congress in Glasgow in 1901, a paper on the profitable utilization of power from blast-furnace gases,' in which he suggested the diversion and cleaning of the whole of the waste gases coming from the blast-furnace and their utilization for power-production, so as to obtain, with proper manipulation, from 4 to 6 times the efficiency of present methods. He suggested also the heating of the stoves with producer-gas of a higher and therefore more suitable calorific value, so as to maintain them in a constant state of maximum efficiency, free from dust, and to avoid the irregular working of the furnace, besides obtaining a maximum supply of air-blast, of 15 or even 20 lb. pressure, by means of internal-conibustion blast-engines driven by the cleaned waste furnace-gases, with a surplus of gas left for other uses. Since that time, in view of the necessity of having a stand-by plant, immediately available, in case of strikes or other reasons causing the banking or blowing-out of the blast-furnace, he has developed, as an addition to his other types of producer, a high blast-pressure gas-generator, producing a gas identical with, or somewhat superior to, blast-furnace gas; and in which all the ash of the fuel is turned into fluid slag, which is available for, the production of slagwool. The gas is a little richer in carbon monoxide than average blast-furnace waste gas, and has only from 1 to 3 per cent. of hydrogen. Fig. I, drawn from a photograph, shows a plant containing this generator, now in operation at Leeds. It is made in units of from 1,000 to 10,000 h.p. capacity for each vessel, and coupled,

Jan 1, 1907

By John Chipman, Carl F. Floe

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By W. F., Netzeband

SEVERAL criteria have been used more or less successfully in finding and developing orebodies in this district. Among them is the relation of the fracture to the orebodies. It has been known for some time that there was some relation, but it has been but recently. that careful study has been given to this subject. Like all the criteria used in this district, this relationship must be used with caution, for what-is true in one part of the district is not necessarily true in another.

Jan 1, 1928

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By E. J. Eisenach, Edward Matsen

AT the present time the Climax Molybdenum Co. is the largest molybdenum producer in the world and the operator of the largest underground mine in North America. It has grown steadily and rapidly since its beginning in 1917. Only 250,000 lb of MoS2 were produced during the first year from 1917 to 1918 when the company was formed. Operations were suspended shortly thereafter because of the lack of a market and knowledge of the uses of molybdenum. During World War I it was used as a substitute for some rare metals and for minor chemical purposes. After 5 years of intensive research and sales promotion, Climax metallurgists succeeded in finding proper applications for the newly discovered metal and the mine was reopened in 1924. Demand for molybdenum increased gradually and in 1930, 3.5 million lb of MoS2 were produced. In the meantime, research work for additional uses of molybdenum continued until it had established itself as one of the most important alloying elements in producing high quality steels. After the start of World War 11, from January 1942 to October 1953, 43 million tons of molybdenum ore were mined and 484 million lb of MoS2 were produced. Climax mine is located in Colorado, 100 miles southwest of Denver and 12 miles northeast of Leadville on the Continental Divide of the Rocky Mountains. The principal mine workings range from 11,170 to 12,000 ft in elevation. Topographically, it lies in the base of a large cirque that is surrounded by Mt. Bartlett to the north, Clinton Peak and McNamee Peak to the east and Ceresco Ridge to the south. This cirque opens to the west and to the Ten Mile Valley.

Jan 3, 1954

By Robert Glass Cleland

BECAUSE of the country's vast mineral resources, Alexander Von Humboldt, the great German scientist who visited Mexico, or the Kingdom of New Spain, a hundred and fifty years ago, very aptly called that country the "Treasure Chest of the World." During the three centuries of Spanish rule, mining was the principal industry of the kingdom, the largest contributor to the country's prosperity, the chief common denominator in Mexican economic life. Public revenues and private fortunes, employment and markets, agriculture and trade, charities and churches, the incentive for frontier settlement and exploration, and the funds for outfitting the expedition of colonizer and conquistador-all were dependent upon the streams of precious metals that flowed century after century from the mines of Guanajuato, Zacatecas, Real del Monte, San Luis Potosi, and scores of other minería that lay scattered everywhere throughout the land. Sonora, one of the oldest and most renowned of the frontier provinces of New Spain, had been the scene of a hundred rich strikes, sudden stampedes, and widely heralded bonanzas long before the famous and frenzied Gold Rush

Jan 1, 1952