Search Documents

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,' and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3'4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.' All material used was guaranteed by the supplier

Jan 1, 1968

By AIME AIME

THE annual meeting of the Auxiliary to the A. I. M. E. was marked by the most delightful cordiality and warm spirit of welcome on the part of the members of the New York Section and an equally charming spirit of cooperation and appreciation on the part of the visitors. On Monday Mrs. Ernest H. Wolfes and Mrs. Charles A. Bohn had charge of registration and most efficiently .provided everyone with the necessary tickets and badges. The reception hall and regisfration booth were gay with beautiful flowers that reflected the welcoming spirit one found there. The smooth efficiency with which the whole program ran was due largely to the tireless efforts of Mrs. Donald M. Liddell and Mrs. Louis D. Huntoon, joint chairmen of the Ladies' Committee, and Miss Margaret Callow, chairman of the Junior Committee. After registering, the ladies proceeded to- the fifth floor, where they had luncheon with the members of the A. I. M. E. On that day Mrs. W. H. Bassett and Mrs. Lucius W. Mayer were the hostesses.

Jan 1, 1929

By L. A. Delano

DURING 1916, the St. Joseph Lead Co. milled 2,505,670 tons of ore. This is a daily operating average of 7855 tons. The economic concentration of such a large tonnage necessarily requires a plant equipped with modern machinery and operated efficiently. The milling process used in producing this output has been a gradual development through the long period of years that the company has been in existence. HISTORICAL SUMMARY OF MILLING PRACTICE Ore was first mined at Bonne Terre, Mo., in 1864. The early milling practice was crude. It consisted of breaking the ore into small pieces by hand, pulverizing in a Blake crusher and a pair of Cornish rolls to approximately minus 6 mm., and jigging in the old-fashioned hand jigs. Only the coarse heavy galena was saved, the gangue being shoveled off and discarded. The output for the first year under this method was only 240 tons of pig lead. The first mill of the company was a combination of extensions and additions built from time to time as the mines developed. It was a museum of early mulling machinery, such as jigs, percussion tables, huddles, dolly tubs, log washers, etc., following no definite flow sheet. The chats, or tailings, were hauled to waste dumps by mule and ox teams, as much as 500 tons per day being moved in this manner, until a railroad was built in 1880. This mill was burned in 1883, at which time the annual output had reached approximately 7300 tons of pig lead. A new mill of 500 tons capacity was designed and built by C. B. Parsons. This mill has been admirably described by H. S. Monroe.1 The ore was crushed in Blake crushers, Cornish rolls, through 6-mm. screens, and treated by jigs of the Parsons type, percussion tables and log washers, or trunking machines, for cleaning the galena. The middlings were recrushed in rolls and treated on Harz jigs. The mill was operated without change, except later installing Gates crushers and en-

Jan 9, 1917

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

Tile National Research Council announces further appointments to National Research Fellowships in physics and chemistry. The object of the National Research Council in maintaining a system of research fellowships is to promote fundamental research in physics and chemistry primarily in educational institutions in the United States. Fellowships are awarded to persons who have demonstrated a high order of ability in research for the purpose of enabling them to conduct investigations at educational institutions which make adequate provisions for research: in physics and chemistry. The new appointments are as follows: In Chemistry.-Warren C. Vosburgh, of New York City, B. S. Union College, 1914, A. M. Union College, 1916, Ph. D. Columbia University, 1919. Research assistant to the Professor of Chemistry at Columbia University for the past six months. George Scatchard, of New York City, A. B. Amherst College, 1913, Ph. D. Colt tibia University, 1917. Formerly research assistant to the Professor of Chemistry at Columbia University and instructor in organic chemistry: First Lieutenant. Sanitary Corns. U. S. A.

Jan 7, 1919

By AIME AIME

THE meeting of the Petroleum Division at Houston, Oct. 10-12-headquarters, Rice Hotel-was preeminently a technological success. Two hundred and twenty-five attended the Thursday morning session and approximately 200 attended the sessions on Thursday and Friday afternoons and Saturday morning. Harry Power, Chairman of the Division, in his opening remarks, credited Paul Weaver and M. Albertson, respectively chairman and vice-chairman of the local committee, with working long and prodigiously in organizing the program. The theme of the initial session was indicated by Mr. Albertson in a statement relative to the estimation of developed petroleum reserves. He said that the problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became an acute one. Mr. Albertson gave some of the more important reasons for this situation. Since the decline-curve method became inapplicable, the volumetric method has become the chief one used. It depends on the factors of productive formation volume, porosity, saturation, and recovery. He briefly discussed the factors necessary for application of the volumetric method. P. P. Gregory discussed the estimation of petroleum reserves in prorated lime¬stone fields (see his paper in the October

Jan 1, 1935

By J. Chipman, H. Towers, M. Paris

A simple radioactive tracer technique is used to measure the diffusion coefficient of calcium ion in molten slags. In a slag of 40 pct Ca0-40 pct Si0,-20 pct Al203, Dc " at 1450°C is 1.3x10-6 cm' sec-'. THE application of the principles of thermodynamics to steel and iron making problems has proved so fruitful that the kinetic approach has tended to be neglected. It seems probable that in some reactions the rate-determining step is the dif-fusivity of the reactants or of the products. But knowledge of the diffusion coefficients of the constituents of liquid slag and metal is singularly lacking. The present work was undertaken as a first step toward supplying such data for slags. Furthermore, any additional information on the physical properties of liquid slags might be expected to help in elucidating their structure. It is essentially a preliminary investigation, the course of which was determined more by the necessity of establishing a method than by the immediate intrinsic interest of the results. For example, the selection of calcium ion to be studied was dictated by the suitability of the isotope Ca45 in that it is a simple emitter with a long half-life. Of the other ions commonly encountered in slags, the isotopes of iron and manganese have relatively complex radiations as well as the normal disadvantage of requiring control of the oxygen potential of the atmosphere; Mg27 and Al29 have half-lives measured only in minutes; Si3' has a simple decay process but its half-life of 2.8 hr is too short for preliminary studies; the only useful oxygen isotope is the stable O18; and there remain only sulphur and phosphorus both of which have suitable isotopes but were rejected as being of less fundamental interest than calcium. Similarly a lime-alumina- silica slag was used in preference to calcium silicate primarily because of its low melting point and its capacity to form a glass on fairly rapid cooling. Literature Review Very few studies of diffusion in liquid silicate systems have been reported. In order to determine the origin of diopside inclusions in felspathic rocks, Bowen1 investigated the diffusion between diopside and various mixtures of albite and anorthite. Platinum crucibles were used with diopside, the heavier of the two liquids, forming the lower half of the cell and diffusion taking place against gravity. Change in concentration along the diffusion path was found by measuring the refractive index of the quenched glass. Nearly thirty years later McCallum and Barrett2 used essentially the same method to determine the diffusion coefficient of lime in lime-alumina-silica slags. In this case the interest was to find the rate-determining step in the process of slag attack on refractory materials. In an investigation of the kinetics of the sulphur reaction, Derge, Philbrook, and Goldman8 determined the diffusion coefficient of sulphur in a typical blast furnace slag by the simple procedure of melting a slag containing 2 pct S over an identical slag sulphur-free. They make no claim to a high degree of accuracy but suggest that D, is of the order of 10-6 cm2 sec-l. Other high temperature liquid diffusion studies have been concerned with metals. Holbrook, Furnas, and Joseph4 determined the diffusion coefficients of silicon, phosphorus, sulphur, manganese, and carbon in liquid iron by immersing a small carbon crucible containing pure iron-carbon alloy in a large vessel containing iron with a high concentration of the particular element. Their results were confirmed by Paschke and Hauttmann5 using a similar method. Diffusion coefficients in silicates in the glassy state have been studied by Johnson, Bristow, and Blau6 Both Na24 and Ca45 were used as tracers but only the

Jan 1, 1954

By Luis Toron, Salvador Cortes-Obregon

John D. Price (Colorado Fuel and Iron Corp., Pueblo, Colo)—The paper on the coal fields of the Oaxaca district as prepared by engineers Toron and Cortes-Obregon of the staff of the Bank of Mexico bears witness to the thorough and careful way in which the men associated with this organization perform their work. There is little to be added to their paper in way of discussion other than to confirm and amplify some of their statements. Since the only extensive and well-developed field of coking coal lies in the northeastern section of the country adjacent to Sabinas in the state of Coahuila, it follows that blast furnace plants would be located in that same region. Two such plants are now operating at Monterrey and Monclova, using coke produced at the Sabinas district mines. But the nearer of these two plants is 600 miles from Mexico City and even farther from the center of population. Transportation of products from these mills to the market area is therefore expensive, both because of the distance and the difficulty of the terrain over which it must be carried. The development of an integrated steel industry closer to the center of population has therefore long been a goal toward which the Mexican technicians have been striving. While the presence of coal of some grade has been reported in many of the states, and many ideas have been advanced regarding its possible uses in iron and steel production, deposits of anthracite in Sonora and the various coals of the Oaxaca district as reported on in this paper are the only ones that have been explored in a serious manner. The coking coal from the Mix-tepec zone appears to offer promise of producing a coke which could be used in a standard blast furnace. Several problems are indicated, however: 1—The ash in the coal is high as mined, but indications are that it can be washed to an ash content of 15 pct with a recovery of 70 pct of washed coal. 2—Such washing would increase the volatile content from 17.4 pct to about 20 pct, and in a byproduct oven this should give a coke yield of close to 80 pct with an ash content of coke under 20 pct. 3—A free swelling index of 5 appears low for a good coking coal, and below that of the coals from the Sabinas district, which show between 6 and 9. But washing of the coal should result in an improvement in this regard; in the United States coals from Utah with an index even lower than 5 have made a usable coke. 4—A coal with volatile as low as 17.4 in raw coal and 20 in washed coal would come close to being classed as a low-volatile rather than medium-volatile coal, and low-volatile coals are notorious for their high expansion properties. Several plants in the United States are making coke from straight medium-volatile coal of 26 to 28 volatile content, and one at Rosita,, Mexico, from coal of 25 volatile. But no plants to my knowledge are using coal as low as 20 volatile. Since the Rosita coal appears to be a borderline coal from the angle of its expansion properties the coking of one of the straight lower volatile must be approached with caution. 5—There are few coals possessing any degree of coking properties which cannot be used in coke production by careful attention to its preparation and blending. The fact that coals of other types are available in this same region make improvement through blending very possible. 6—There are other workable methods of reducing iron ore other than the conventional coke-blast-furnace method. These will not be discussed here but it is known that their use has been considered. The technicians of not only Mexico but also of the other Latin American countries are keenly aware of their natural resources and their national needs. This paper emphasizes the fact that the Mexican technicians are working on their problem and attempting to speed the day of self-sufficiency for their country. Salvatore Cortes-Obregon (author's reply)—I wish to thank Mr. Price for his kind remarks. The Mixtepec coal as shown in Table II has 30 pct ash and a free swelling index of 5, but when the same coal is washed to 15 pct ash it has a free swelling index of 8 to 9 and the volatiles increased from 17.4 to 20.7 pct. A satisfactory coke has been produced from blends made in the Mexican laboratory using at least 40 pct of the Mixtepec coking coals with the other Oaxaca non-coking coals. Koppers in Germany report good coke obtained from the Oaxaca coal with a blend of 80 pct Mixtepec coal. Consideration is being given the possibility of using methods other than the conventional blast furnace for the reduction of iron ore near the Oaxaca area; electric furnaces appear promising. The non-coking coals could be used to produce cheap electric energy and the coking coals to make metallurgical coke.

Jan 1, 1955

By Robert Anderson Cook

AS the margin of profit in the manufacture of iron continues to decrease, attention is called more and more to economies in every department. Beginning at the bottom, in the preparation of the ore at the mine, me notice a general tendency is towards the shipment of richer ores, securing to the mine-owner a better price per ton, which the purchaser is glad to pay by reason of the saving in freight of iron, and in the cost of reduction, which depends so largely upon the amount of fuel and flux, and the productive capacity of the plant. In other words, the difference in value between rich and poor ores is much greater than their relative percentages of iron indicates; because the barren material in a lean ore is not merely worthless, it is a positive source of expense, requiring transportation, handling, fluxing, smelting, and its due share of general expenses; in return for which it yields nothing and decreases the available capacity of a given plant and capital for profitable work. The enriching of the ore is done in most places by hand-picking, and in a few by wet concentration; but the managers of several magnetite mines in Sweden have been practically successful in doing it by machinery. The only magnetic separating machine which has actually taken the place of hand-picking was designed and patented by Mr. Jonas Wenström of Örebrö, Sweden. In this machine, which is illustrated in Figs. 1 and 2, Mr. Wenström has taken advantage of the property of soft iron to become magnetized by induction. The machine consists of a barrel made up of soft iron bars and some non-conducting material (usually wood), which is rotated around a stationary shaft by means of a cog-wheel. Inside of this barrel, on the shaft, is placed eccentrically a cylindrical electro-magnet, provided with a number of manges (N, S, Fig. I), between which wire is wound in such a manner that the flanges are of negative and positive polarity, being energized by a current passing through the wire coils from a small dynamo. As will be seen in Fig. 1, the flanges, N, S, are circular, and follow the internal contour of the barrel on the front side, while on the opposite side they are cut down to the line B, B' in Fig. 2. Hence the bars of the revolving barrel on the front side of the machine are mag-

Jan 1, 1889

By J. T. McGrath, G. B. Craig

Tensile tests on aluminum single crystals, grown from the melt, revealed that the yield stress of these crystals was raised as the amount of striation substructure was increased. The number of striation-type boundaries was varied by changing the rate of growth of the crystals. The results are interpreted in terns of a blockage of dislocation movement by striation boundaries. IMPERFECTIONS are known to have a large effect on the mechanical properties of metals. Teghtsoonian and Chalmers 1 studied a block or striation-type substructure in tin and found that the formation of the striations depended upon rate of crystal growth and orientation. They found that the angular misorienta-tion between neighboring striations varied between 15 min and 5 deg. Atwater and chalmers2 investigated striations in tin and lead, and found that purity was another factor which influenced their formation. There was a limiting purity above which the striations were straight and regular. There is little information in the literature concerning how substructures in melt-grown crystals affect strength. washburn3 introduced small-angle boundaries into zinc by a shear process and found a subsequent increase in yield stress which he attributed to the presence of these boundaries. Lauriente and pond4 found the critical resolved shear stress in aluminium crystals grown from the melt, to increase with etch pit density. The etch pits were used as an indication of growth imperfections. In Hibbard's5 work on lineage structure in copper crystals grown from the melt, he tested one crystal containing interlineage boundaries, and found a 50 pct increase in the critical resolved shear stress. Fleischer and Chalmers6, in a recent paper, mention briefly that, in the production of aluminium crystals from the melt when the growth rate was raised from 1.2 to 18 cm per hr, the yield stress increased 50 pct. They felt that the increase in yield stress with rate of growth might be attributed to a higher concentration of impurities in the gage length and also might be affected by the increased number of small-angle boundaries (striations). The present investigation was undertaken to determine the effect of the striation substructure on the strength of aluminum single crystals. EXPERIMENTAL PROCEDURE Aluminum single crystals of 99.9992 purity were grown from the melt using a technique described by Chalmers.7 The growth rate was varied from 0.6 to 20 mm per min, thus producing crystals with varying numbers of striation boundaries. To avoid prior deformation, the crystals were chemically cut to the desired length with a saturated solution of cupric chloride. They were then annealed at 580°C for 24 hr and allowed to cool slowly in the furnace. Finally, the specimens were electropolished using an electrolyte of 5 parts ethyl alcohol and 1 part perchloric acid. Each specimen was approximately 5 in. in length and 0.125 sq in. in cross section. The average orientations of the 5 series of crystals studied are shown on the stereographic projection of Fig. 1. The crystals were strained approximately 2 pct in a soft tensile machine. The strain sensitivity was 3.6 x 10-4 cm over a 5-cm gage length.

Jan 1, 1960

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

By Rossiter W. Raymond

The formal outline of Mr. Hague's life and work is embraced in the following statement, chiefly based upon data furnished by him, at my request, shortly before his death. At that time the probability that I would survive to record his death was apparently small; but I urged upon him the duty of providing, whether for me or for my successor as Secretary of the Institute, trustworthy material for the notice which somebody would some day have to write—and which might otherwise be incomplete or incorrect. Mr. Hague, with characteristic promptness and freedom from affectation, did what I asked of him; and I am therefore able to present an authoritative sketch—concerning the details of which I shall add my own comments, and some particulars obtained from friends. James Duncan Hague was born Feb. 24, 1836, at Boston, Maes., where his father, Rev. William Hague, D.D.,an eminent clergyman, then resided. After a preliminary education in private schools, he studied in 1854 at the Lawrence Scientific School of Harvard University; in 1855 and 1856 at the University of Göttingen, Hanover; and from 1856 to 1858 at the Royal Mining Academy of Freiberg, Saxony. In 1859-1861 he was attached as chemist to a South Sea exploring expedition, sent by W. H. Webb, of New York, to examine Jarvis, Baker, and other islands for phosphate-deposits. After the outbreak of the Civil War, he entered the U. 5. Navy, serving for a year as Judge Advocate to the fleet stationed at Port Royal, S. C. In 1863 he became Superintendent of the Albany and Boston copper-mine, in the Lake Superior region, where he was also connected with the earliest development of the Calumet and Hecla property. In 1867 he became the First Assistant Geologist in Clarence King's famous Exploration of

Jan 1, 1909

By Morris A. Steinberg

Because of the broad scope of my topic I will discuss my subject from the point of view of a present status of the metallic materials that are used in structures and will dwell primarily on those structures related to high- performance aerospace systems. Thus, I can best portray the status of these structural materials as related to existing transportation systems, delineating some of the highlights of alloy development, fabrication, and properties obtained. I shall point out what are, in my opinion, the needed solutions to pressing unsolved metallurgical problems connected with certain selected metals: aluminum alloys, beryllium, titanium, steels, superalloys, refractory metals and some metal-matrix composites. Aluminum Alloys For a number of years a series of strong aluminum alloys used for airframes has had an important bearing on the development of minimum- weight, highly efficient structures. Among these alloys are such familiar ones as 2024-T3, 2014-T6, 7075-T6, 7079-T6 and 7178-T6. A review of the development and use of strong aluminum alloys in aircraft structures indicates that before about 25 years ago there was very little application of products other than forgings in the high-strength tempers produced by precipitation heat treating to T6- or T8-type tempers. 1 As stated by Dix in 1944, "There has been a gradual evolution in engineering viewpoint regarding the mechanical characteristics which are required in a structural material suitable for aircraft. Formerly, emphasis was placed on a generous spread between yield and tensile strengths, on elongation, on impact strength and on resistance to corrosion. Aircraft structural engineers still differ widely as to the importance which they attach to these proper tie.” 2 It is fair to say that this evolution is still taking place, that the problem is much the same in 1970 as in 1944 - except that strength levels have advanced some - and the question remains as to how far we can go in that direction. In the meantime, a new group of alloys has received acceptance and widespread use. The first alloy of this group, 7075-T6, was formally introduced by Dix's 1944 paper. The drastic changes that have taken place in the size and configuration of components employed in air-

Jan 1, 1971

By F. R. Morral, K. T. Aust

The preferred orientation and earing characteristics of ZS aluminum were studied. An empirical correlation was obtained relating earing behavior and variation of mechanical properties for face-centered cubic metals. Strain-ratio mecsurements for ZS were found to be in good agreement with Hill's theory of plastic anisotropy. DIRECTIONALITY in sheet metals may be revealed by earing in a cupping test, or by the variation of mechanical properties of tensile specimens taken at different angles to the rolling direction. However, no simple correlation appears to exist between earing and variation in mechanical properties in metals and alloys studied.1-5 Aluminum of commercial purity (known as 2S, with a specified minimum of 99.0 pct Al) cast by the direct casting process was chosen in the present investigation since ears at 45° or 0°, 90° can readily be obtained. Preferred orientation is often the principal cause of uneven metal flow, such as earing, and variation in mechanical properties. Consequently, the preferred orientation characteristics of 2s aluminum were initially studied using both X-ray diffraction and micrographic techniques. The variation of mechanical properties with angle to the rolling direction was next determined in an effort to clarify the apparent lack of correlation of earing behavior with mechanical properties for face-centered cubic metals. Strain-ratio*5,8 measurements were finally conducted to determine first, if the maximum values of the strain ratio occurred at the earing positions, and second, if Hill's theory of plastic anisotropy7 is applicable to other face-centered cubic metals such as aluminum. Detailed treatments, working, and heat treating are not given in this paper since this study is not concerned with the methods to produce earing, but to correlate earing with other properties and characteristics of the material. The percentage of earing was measured using the formula specified by the x—Y Aluminum Association, -------- X 100 = pct earing, where x is the height of the ear and y is the height of the valley from the bottom of the cup. Preferred Orientation Characteristics of 2S X-ray Studies: Beck and coworkers8 have determined that the rolling texture of 2s after 95 pct cold reduction may be approximately described by four equivalent ideal orientations near (123) [121]. Also, the recrystallization or annealing texture of 2s aluminum consists of four components of the (123) [l21] type, retained from the rolling texture, and of a (100) [001] or cube texture component." Fig. 1 illustrates the typical appearance of deep drawn earing cups with the corresponding X-ray diffraction patterns. The X-ray patterns were taken with copper radiation using the structure-integrating method'" in which the specimen is scanned during the X-ray exposure. The rolling direction was vertical and the rolling plane was perpendicular to the horizontal X-ray beam. It was found that an increase in the retained rolling texture component resulted in a greater 45" ear height, while an increase in the recrystallization texture component (i.e., cube texture) caused greater 0°, 90° earing. X-ray diffraction studies of 2s cold rolled to final thickness followed by a final anneal have shown that the rolling texture, and also the retained component of the rolling texture after annealing, are increased with greater cold-rolling reduction. The preferred orientation characteristics of 2s sheets given an intermediate anneal between cold rolling followed by a final anneal were found to depend on the position of the intermediate anneal during cold rolling. For instance, three identical samples of 2s homogenized ingot, each 1 in. thick, were given the following cold-rolling and annealing treatments: 1—50 pct reduction, intermediate anneal, 96 pct reduction to 0.020 in. and a final anneal; 2—75 pct reduction, intermediate anneal, 92 pct reduction to 0.020 in. and a final anneal; and 3—90 pct reduction, intermediate anneal, 80 pct reduction to 0.020 in. and a final anneal. The intermediate and final annealing treatments consisted of a 70°F per hr heating rate, held 6 hr at 800°F and air cooled. Typical X-ray patterns after each of these treatments are shown in Fig. 2. It was evident that after treatment 1, the retained rolling texture component predominated; after treatment 2, the retained roll-

Jan 1, 1954

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920&apos;s and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.o.b. mines, the output in 1948 was 1,568,848 tons worth $19,756,738.

Jan 6, 1950