Search Documents

THE Annual Fall Meeting held in Chicago in conjunction with the celebration of a Centennial of Engineering brought forth a round of field trips and symposiums which did much to add to the store of information of the 240 who registered for the gathering. Instead of a scattered program, technical papers were grouped together in organized symposiums, where the particular importance of each report was enhanced by presentation in context. Despite the heavy accent on technical papers and informative field trips, those attending the meeting had ample time to enjoy the benefits of a visit to Chicago. The AIME dinner dance was held at the Palmer House, in the Red Lacquer Room. The Chicago Section played host Friday evening at dinner. The MBD held four sessions at the meeting headquarters, the Palmer House, September 4 and 5. Featuring the meetings was a review of taconite concentration and new theories on comminution. The first session opened with a paper on the Structural Features Which Effect the Concentration of Iron Formations, presented by F. J. Tolonen. The paper was centered upon the various members of the low grade iron formations of the separate Michigan districts. The study correlated macrostructure, microstructure, and concentration tests. [ ] Beneficiation Characteristics of Michigan Low Grade Iron Ores, presented by F. X. Tartaron, cochairman of the session, reviewed the work of his laboratory on the beneficiation of low grade ore taken from various strata of a deep shaft on the Marquette Range. The paper included data on flotation, gravity separation, magnetic separation, and combinations of these processes. The economics of low grade ore treatment generated great interest. Ty. Maki offered a compilation and correlation of field results with magnetic separators in ferrosilicon and magnetite medium recovery circuits. Following the morning session, 130 persons attended a luncheon, followed by a brief business meeting. Later, a film illustrating the grinding, separation, and pelletizing steps investigated by the Mines Experiment Bureau, was presented by H. H. Wade. T. E. Ban, and L. J. Erck gave a report on pelletizing which evoked much discussion. R. A. Limons presented a paper on the Mineralogy of Blast Furnace Sinter, for its author, H. M. Kraner. Friday sessions featured a new hypothesis for high speed drill rod milling and a new technical approach to comminution. Jack Myers commented that Consolidated's large rod mill was a hammer mill turned inside out. Steve Erickson described the use of Cyclones for Heavy Media Concentration of Iron Ore Fines. Bob Meaders gave a Progress Report on the Aerofall Mill. Shiou-Chuan Sun described an improved high frequency analyzer for studying the conductivity of suspensions of various minerals. L. A. Roe discussed a magnetic reflux condensor which enabled him to determine the degree of liberation of magnetic iron ores. Roy A. Johnson described a function of the hydroscilator in which the fan rake was eliminated in favor of a conical bottom. The Industrial Minerals Division sessions held September 5 and 6 and were well attended. The Friday morning session was particularly concerned with developments and advances in industrial minerals with special emphasis on the Chicago area. The first two papers dealt with transportation on the Great Lakes and fuel movement into the Chicago area. The third paper proved to be of great interest, turning the spotlight on the fairly new hydraulic mining methods introduced by a silica company in the Ottawa, Ill. field.

Jan 1, 1952

By C. R. Fast

In order to evaluate the ability of a Hydrafrac treatment to effect a sustained increase in well production, data were accumulated on the first 65 wells in 26 fields treated by Stano-lind. Since these data were obtained from such a large number of fields, it is felt that individual well or reservoir characteristics do not affect the overall picture, as might be the case if the study were made in one field or one group of wells in a field. These data are tabulated in Table I and plotted on Figs. 1 and 2. An analysis of Fig. 1 shows that at the end of six months, 75 per cent, or 45, of 60 wells on which data were available showed a sustained production increase. At the end of two years, data were available on 25 wells. Of these, 15 wells, or 60 per cent, showed a sustained production increase. At the end of three years, 55 per cent, or 10, of 18 wells had a production rate greater at that time than before Hydrafrac treatment. The lack of information on additional wells at the end of the third year is primarily a result of the small number of treatments conducted in the early stages of field application

Jan 1, 1952

By Lars Rossemyr, Terkel Rosenqvist

The equilibrium Mn + 2 IiCl = MnCl2(g) + H2 has been studied at 1090°C for pure manganese and for Mn-Si alloys. For this reoction a standard free energy of Fo1363, = - 19,700 i 300 col ioas found. Combined with other thermal data, the standard free energy of the reaction Mn(s, ß) + Cl2 = MnCl2(g) was derived: Fo=- 56,140 + 9.78 T log T - 40.10 T For the formation of the various manganese silicides the following free energies were obtained. 5 Mn + 3 Si - M1z5Si3 ?F°1363 = -41,500 i 1500 cal Mn + Si - h.lnSi ?F°1363= -10,000 i 500 cnl Mn + 2 Si = MnSiz ?F°1363= -11,500 ± 500 cal In the search for a method suitable for the study of thermodynamic properties of certain alloy systems, it was found that the heterogeneous equilibrium between the alloy and a gas mixture consisting of hydrogen chloride, hydrogen, and volatile metal chlorides has considerable advantages. In addition to giving thermodynamic information about the alloys, such measurements may be used to derive thermodynamic data for the volatile metal chloride itself. The present paper gives some results which were obtained for manganese silicides and manganous chloride. Similar studies are presently being carried out for the iron silicides. The phase diagram of the Mn-Si system is rather well known,' but no information exists to the authors' knowledge about the thermodynamic properties of manganese silicides or about the chemical activities in molten Mn-Si alloys. At elevated temperature, manganese may react with hydrogen chloride according to the equation: Mn(s, ß ) + 2 HC1 = MnC1, (g ) + H2 [ 1] with the equilibrium constant The value of K, may be determined from measurements of the gas composition in equilibrium with pure manganese. When this value is used in connection with measurements on manganese alloys, the chemical activity of manganese in the alloy may be derived. Initial calculations showed that around 1000" to 1200°C the equilibrium constant K1 has a value of a few thousand, i.e., the reaction is shifted far to the right. In order to study this rather unbalanced gas composition, a flow method was used in two slightly different modifications. For all experiments with manganese silicides and for some experiments with pure manganese the apparatus shown on Fig. 1 was used. A bed of the metal or alloy was placed in a tube furnace. The refractory tube had an internal diameter of 14 mm and the bed was 75 mm long. Electrolytic manganese of high purity and silicon, 99.95 pct Si, were used as raw materials. All alloys were prepared by melting weighed amounts of the elements in a high frequency induction furnace in argon atmosphere. The melting was done in a silica crucible which was placed inside a graphite shell. The alloys were crushed to - 10 +40 mesh and analyzed chemically. Also, for the pure elements, the same size fraction was used. A controlled gas mixture of purified hydrogen and from 3 to 12 pct HC1 was passed through the bed where it reacted with manganese according to Eq. [I]. The volatile manganese chloride was collected in a condenser placed in the cooler part of the furnace tube. The gas mixture before and after the furnace was sampled and analyzed by absorption of

Jan 1, 1962

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By Walter Knox, Charles H. Sawyer

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By Carl Scholz

During November and December, 1907, four serious mine-explosions occurred in the Appalachian coal-field, which resulted in the loss of nearly a thousand lives and caused an eliormous damage to propcrty. These accidents attracted more than the usual attention; coal-trade and engineering papers contained many comments and suggestions on the cause and prevention of accidents; the daily press in many instances condemned the coal-operators and charged these accidents to their negligence, or their anxiety to make money without adopting precautionary measures. Immediately after cach accident the respective State authorities ordered close investigations to be made, with the view of establishing the cause and suggesting remedies to prevent recurrence. Representatives of the Technologic Branch of the IT. S. Geological Survey, to whom the investigation of mine-accidents had recently been delegated by the Secretary of the Interior, visited the mines and co-operated with the local authorities in their determinations. It may be safe to say here that an investigation of a mine after an explosion has occurred discloses but little, because the causes hare been removed and conditions have been entirely changed. On Jan. 8, 1908, the coal-operators of West Virginia organized an association at qTashington for the purpose of making extensive investigations, and sufficient funds were pledged to carry out this work. At this organization meeting, the representatives of the Geological Survey present had no suggestions to offer as to the cause of these accidents. An examinatiou of the various reports concerning these accidents indicates that the explosions were caused by the ignition of gas or dust; they show the point of origin and the direction in which the force was expended, and give a detailed description of the damage done. Very little has bee11 said as to what

Jan 1, 1909

By S. L. Hoyt

ABOUT three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. ? This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some com-ments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1.

Jan 1, 1937

By Jerry H. Service, F. L. Partlo

The following investigation was undertaken to develop a method for determining with reasonable accuracy the depth of overburdens of 100 ft. or less. Seismic methods seemed to offer good possibilities. The problem differed from that of the familiar salt-dome location in that the depth of overburden to be determined is much less than is encountered in oil prospecting. This means that a much shorter time interval must be measured with accuracy. Refraction methods seem at present to offer greater possibilities than reflection. The air sound persists for from 0.1 to 0.5 sec., because of echoes, and seismic reflections coming during this time are difficult to detect. A seismometer sensitive to vertical vibrations only offers possibilities and has been used here with some success. It is hoped that the application of this type of seismometer to reflection shooting in this region may be investigated still further. The apparatus used consisted of a carbon-button seismometer followed by a three-stage, transformer-coupled, vacuum-tube amplifier and a General Radio string oscillograph. Time marks are provided by a 1000-cycle, 600-r.p.m., synchronous motor provided with five spokes which intercept the light to the camera at 1/50 sec. intervals. This motor is driven by a two-stage vacuum-tube amplifier of 3 watt output, actuated by a tuning fork. The power supply for the seismometer amplifier is one 2-volt storage and one 45-volt B battery. The motor amplifier is powered by a 6-volt storage battery and 6 to 225-volt, 15-watt motor generator. The temperature-frequency characteristics of the tuning fork have been determined and for ordinary working temperatures the error in time that would be introduced is less than M millisecond for time intervals up to 100 milliseconds. The impact is produced by a sledge blow for surface distances less than 100 ft. and dynamite for greater distances. Two steel balls with wires attached form an electric circuit through a 1-ft. piece of railroad rail upon which they rest. When the rail is struck by the sledge the balls rebound, opening the circuit and indicating the time of impact by a break in the oscillograph record line as at A, Fig. 3. When dynamite

Jan 1, 1934

By Robert F. Love

Deep under the hills of southwestern Wyoming lies a nonmetallic mineral deposit of incredible dimensions and value. This nearly pure, horizontal bed of the mineral trona, a sodium sesquicarbonate (Na2HC0,.NaHC08.H20), is found in the Green River formation some 1500 ft below surface. It is believed that evaporation of an ancient saline lake left this sodium carbonate as the evaporite and mysteriously left practically no sodium chloride, which is the common constituent of an evaporated saline lake. The trona bed averages 10 ft in thickness and extends over an area of several hundred square miles. In 1938 a geologist with the U. S. Geological Survey identified the trona in the core from a former oil exploration drillhole. By so doing, he initiated the developments of a chemical industry of impressive growth in the area, an industry on the threshold of further and much more spectacular growth. A drilling program by the Union Pacific Rd. and Intermountain Chemical Co. in the early 1940's succeeded in blocking out mineable reserves of several hundred million tons. Development of the deposit started in 1946 with the sinking of a 12-ft diam, concrete-lined shaft 1500 ft deep-followed by construction of a small pilot calcining plant. Actual mining of the trona started in 1947 and continued on a limited scale until 1953, when the $15 million surface facilities were completed, along with the second shaft and other expanded underground facilities. Since April 1953 the mine has been producing more than half a million tons per year, from which the refining plant has produced more than 300,000 tons per year of high quality soda ash.

Dec 1, 1956

By R. E. Collins, Paul B. Crawford

Mathematical equations have been derived to show the effect of the slippage phenomomenon (Klinkenberg effect) on unsteady-state gas flow through porous media. The assumption is made that the slippage may be represented by an equation of the type It is pointed out that most of the existing data on unsteady gas flow may be corrected for slippage by a simple change in definition of the dimen-sionless groups. INTRODUCTION Several solutions to the various problems associated with the unsteady-state flow of gas through porous media have been recently presented in the literature.','" The cited publications have resented solutions for flow under ideal conditjons. The principal assumptions involved include: (a) the density of the gas obeys the perfect gas law; (b) the viscosity of the gas is constant; and (c) the gas permeability is constant. Few, if any, actual gases under reservoir conditions are believed to conform with the above, but the ideal solutions do provide the basis for making improved estimates on the performance of gas reservoirs. The purpose of this paper is to show the performance characteristics when assumption (c) is corrected for the slippage phenomenon or the Klinkenberg effect. This is believed to be a step nearer to reality. MATHEMATICAL DEVELOPMENT Case 1. Gas Flow — Ideal Conditions The equations describing the flow of gas under ideal conditions have been clearly presented in the cited literature; however, for completeness of this work they are repeated here. The basic differential equation describing the flow of gas is Equation (6). It may be derived as follows: The continuity equation, the perfect gas law and Darcy's law are combined to give: Manuscript received in the Petroleum Branch office Aug. 3, 1963 or If — is constant, Equation (5) is rewritten to form the basic Equation (6). or for the linear case A dimensionless equation is obtained by dividing through by (pl)z and making the substitutions shown below: The resulting equation is A similar procedure for the radial case leads to the following equations: where and Equations (11), (12), and (13) are those used by Bruce, et al., and Jenkins and Aronofsky for their computational work.

Jan 1, 1953

By W. Vickers

SALKOVITZ1 has given a number of useful angles between planes for use with the Laue method in determining the orientation of bismuth single crystals. Bismuth is usually considered as having a face-centered-rhombohedra1 structure with its axial angle 87°34', Fig. 1. A similar figure given by Sal-kovitz appears to be in error in that the angle there marked as 87°34' should be 92°26. The primitive cell is a single rhombohedron of axial angle 570 14. The structure is almost face-centered-cubic and hence high accuracy in measurements is essential if there is to be no confusion in indexing poles or zone axes. It is easier to get this accuracy if zone axes are plotted on the stereogram because they will lie near the basic circle where the net has a more open scale. The zone axes can be read from the film, using a Greninger chart, and can be plotted more accurately than poles. Also, the angles between points near the basic circle can be read more accurately than those between poles near the center. In order to use the zone axes the angles between directions have been calculated from a formula given by Niggli,2 and are given in Table I. Miller indices

Jan 1, 1958

The Fifth Annual National Exposition of Chemical Industries will be held in Chicago at the Coliseum and First Regiment Armory during the week of Sept. 22. It was decided to hold the exposition in Chicago, this year, for two reasons: The U. S. Army commandeered the Grand Central Palace Exposition Building in New York, immediately on the close of the last exposition and converted it into a receiving hospital, the use for which is now, happily, nearly ceased; and it was thought that the Exposition would succeed in bringing about a greater development of chemical industries in the Chicago district and the adjoining states. The Advisory Committee of the Exposition consists of: Charles H. Herty, Chairman, Editor Journal of Industrial and Engineering Chemistry; Raymond F. Bacon, Director, Mellon Institute; L. H. Baekeland, Member Naval Consulting Board; W. D. Bancroft, President, American Electrochemical Society; Henry B. Faber, Industrial Filtration Corpn.; Ellwood Hendrick, President, The Chemists' Club; Bernard C. Hesse, Chemist, General Chemical Co.; A. D. Little, President, Arthur D. Little Inc.; Wm. H. Nichols, President, American Chemical Society; R. P. Perry, Vice-president, The Barrett Co.; H. C. Parmelee, Editor Chemical &; Metallurgical Engineering, G. W. Thompson, President, American Institute of Chemical Engineers; T. B. Wagner, Vice-president, U. S. Food Products Corpn.; M. C. Whitaker, President, U. S. Industrial Chemical Co.; and Charles F. Roth and Fred W. Payne. There is also added a special Chicago committee consisting of L. V. Redman, W. D. Richardson, A. V. H. Mory, Carl S. Minor, F. W. Willard, and Wm. Hoskins; the managers, as in the past, are Charles F. Roth and Fred W. Payne.

Jan 6, 1919

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10, 1916 to Dec.10, 1916. BARNSDALL, THEODORE N., Treas. & Mgr., Highland Gas Co., 24 West Corydon. St., Bradford, Pa. BEASLEY, FRED E., Asst. Supt., Copper Refinery, Consolidated Mining & Smelting Co., Trail, B. C., Canada., BREWSTER, THOMAS T., Vice Pres., Gen. Mgr., Mt. Olive & Staunton Coal CO., 1012 Federal Reserve Bldg.,-St. Louis, Mo. BRINDLE ARTHUR ST. C.... Mining Recorder's Office, Trout Lake, B. C., Canada. BULLOCK, Harry E., Pres Kentucky-Jewel Coal Co., Lothair, Ky. BUTLER, PERCY BENNETT, Mine Operator :..P. 0. Box 335, Joplin, Mo. BUTLER, ROBERT S Supt., Three Johns Mining CO., ,Joplin,.Mo. CABOT, Godfrey, L., Carbon Black Maker, Gas Engr., 940 Old South Building Boston Mass.

Jan 1, 1917

By V. D. Perry

Carlisle: Reno, let's start off by asking "When was the first day that you began working in your profession?" Sales: I began in Butte, Montana, on August 22, 1900 as an assistant engineer for the Boston & Montana Consolidated Copper and Silver Mining Co., and continued at that job for about a year. The general manager was C. S. Batterman, and the mines- Mountain View, Pennsylvania, Leonard, East Colusa, and one or two others-were part of Boston & Montana.

Jan 5, 1966

By R. H. Goodrich

Development in this district during the year 1929 was little different from that of any other year despite the somewhat depressed condition of the oil business in general. The year was marked by: (1) An intensive geophysical campaign in the search of deep-seated salt domes; (2) the rather successful exploration and development of lateral sand production on the flanks of some of the older domes. Geophysical Exploration Geophysical work is confined almost exclusively to the torsion balance and seismograph. At the beginning of the year there were approximately 185 individual instruments of all types engaged in the search of structures in the Gulf Coast of Texas and Louisiana. This total includes 3 magnetometers, 83 torsion balances and 100 seismographs. The number of parties operating the torsion balances was 47; seismographs, 20; magnetometers, 3. It is estimated that 4,800,000 lb. of dynamite or other explosives were used in seismic exploration. During the year the torsion balance and seismograph were credited with having discovered the following salt domes: Texas, Danbury dome, Brazoria County, H. & T. B. R. Co., and Clodine dome, Fort Bend County, John Fredricks and Wm. Stanley, Satowsky Survey; Louisiana, Iowa dome, Calcasieu and Jefferson Davis Parishes, T. 9 S., R. 6 and 7 W., and Cameron-Meadow dome, Cameron Parish, T. 14 S., R. 13 W. Because of the secrecy maintained in these developments, it is somewhat hazardous to venture opinion as to the number of salt domes found during one year. The discovery of gas at Mykawa district and at Genoa district, in Harris County, Texas, is considered of more than passing importance, because there is indication in the performance of these two districts that commercial accumulation of oil and gas may be found in the Gulf Coast on structures other than the wore or less definite salt dome type. While it is generally conceded that the accompanying structure in these instances are deeply buried salt domes, it is a fact that neither the seismograph nor the drill have indicated the presence of salt.

Jan 1, 1930

By F. H. McDowell

For more than two hundred years Mexico has been enriching the world from her inexhaustible wealth of precious metals. From this source alone, over three thousand five hundred millions of dollars have been poured into the coffers of Europe and America. During these centuries the wants of the country in manufactured goods have been supplied from the mills and machine-shop of the Old World. English, French and German merchants in Mexico have vied with each other in their efforts to control the importing of these goods from their respective countries. The overthrow of Maximilian, the departure of the French and the restoration of the Republic, largely influenced by the strong stand taken by the United States Government during our own civil war, established a new order of things. Americans were encouraged to visit the sister republic, examine into the needs of the country, as well as its resources, and interest themselves in the work of development. More recently, under Presidents Diaz and Gonzales, liberal inducements have been extended to American capitalists to build railroads, open mines, erect reduction-works, raise cattle and improve the crude systems of agriculture. The Mexican Central Railway has been pushed south from the Rio Grande to the Capital, and, by its branches and connections, makes the whole mineral belt of the country accessible.

Jan 1, 1885

By BION J. ARNOLD

WE can, I think, rightfully claim, irrespective of our faults, that engineers must, in order to last as engineers, possess the qualifications of integrity, stead- fastness of purpose, ability to think straight, and to apply these qualities consistently and continually in their everyday work. All engineers know this, most of them conform, and in order to drive it home I might, if 'clothed with proper authority, preach to you at length, but I shall not take the chance. So I only want to make a suggestion or two to the young engineers. Have an ideal and work toward it. You will have your disappointments and your temptations but keep your record clean, and if anyone says you are foolish or ugly, or homely, or that you need a guardian, take the criticism with a smile, for he may be able to prove his contention; but if he attacks your integrity, strike at once and fight hard, for he has assailed not only your character but your principal asset as an engineer.

Jan 1, 1929