Search Documents

Jan 1, 1944

By P. Davey Wheeler

San Francisco meeting, September, 1915) IN an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in. thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. 1.) Fig. 2 is a photograph of the end of the punching, showing the .hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of, radiographing metals. In order to gain some preliminary data, several pieces of ½ -in(12.5mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter 1 1/4 in. = 6.3 mm 2 1/8 in. = 3.1 mm. 3 1/16 in. = 1.6 mm. 4 1/32 in. = 0.8 mm. 5 1/64 in. = 0.4 mm.

Jan 8, 1915

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid cobalt and a number of dilute cobalt alloys Was measured in the temperature range 1550" to 1700°C at nitrogen pressures to 1 atm. At 1600°C and 1 atm nitrogen pressure, the solubility in pure cobalt is 0.0047 wt pct [3.8 cu cm (stp) per 100 g Co]. The standard free- energy change for the solution reaction 1/2 N,(g) = gout pct in Co) is iF - 10,000 + 5.24 T cal per g atom N. The alloying elements Cv, Cu, Mo, Nb, Tu, W, and V increase the nitrogen solubility, while Al, Fe, Ni, and Si decrease the nitrogen solubility. THE solubility of nitrogen in cobalt was studied previously by Sieverts, Busch and Dodd,2 and Schenck, Frohberg, and Graf.3 Sieverts investigated the solution below the melting point of cobalt, and Busch and Dodd worked with the liquid metal; however, neither study found any solubility for nitrogen in cobalt. Schenck et al, reported a solubility of 0.005 wt pct N in cobalt at 1600°C. Seagle et al. 4 reported residual nitrogen in cobalt after electron-beam melting, although no reasons were ventured for the presence of this interstitial impurity. This investigation was undertaken to clarify these inconsistencies, and to provide additional data on atomic interactions in dilute metallic solution. EXPERIMENTAL PROCEDURE This study was well-suited to the Sieverts' method, which has not changed significantly since its introduction by Sieverts. 5 The apparatus was of the same design as that described by Humbert and Elliott, 6 with a reaction bulb similar to that reported by Weinstein and Elliott. 7 The buret was not water-jacketed, but the measured gas volumes were corrected for small changes in room temperature. The melt temperature was measured by a disappear ing-filament optical pyrometer sighted through a prism onto the melt surface. Temperature calibration was made based on a measurement of the melting point of pure cobalt taken as 1495°C. The difference between the reciprocal of the observed and the true temperatures was assumed to be a constant, neglecting the changes in emissivity with small additions of alloying elements. The total error in gas-volume measurement caused by accuracy limitations in reading the mercury level in the buret, variation in ambient temperature, and variation in melt temperature was about 0.5 cu cm. This represents approximately 10 pct of the total solubility, and is a larger relative error than in previous studies6-' because of the small nitrogen solubilities encountered in the present investigation. The source and purity of the materials used are listed in Table IA. Recrystallized alumina crucibles were used throughout the investigation. Examination of the crucibles after solidification of the melts showed no reaction or penetration. Alloying of the cobalt melt was accomplished with the dropping technique described by Humbert. 6 The investigation was started using cobalt from African Metals Corp. in shot form, but this material was not of sufficient purity and did not yield consistent solubility results. Sherritt Gordon Mines Ltd. cobalt was then used throughout the investigation. In experiments involving alloying elements which could react with oxygen dissolved in the melt, the cobalt was further refined by annealing at 1400°C in a dry-hydrogen atmosphere. This treatment, described by Woolley and Pehlke, 8 markedly reduced the oxygen content. The oxygen and nitrogen analyses of the cobalt used in this study are presented in Table IB. RESULTS Hot Volume. The hot volume was measured prior to each run and was 50 to 55 cu cm (stp) at 1600°C. It increased linearly with increasing pressure and decreasing melt temperature. Pure Cobalt. Measurements of the solubility of nitrogen in pure cobalt and the temperature coefficient of solubility are summarized in Table 11. At 1600°C and 1 atm nitrogen pressure, the solubility was found

Jan 1, 1967

By W. J. Shearer

A COMPARISON of statistics relating to coal min-ing in Great Britain and the United States leads one to suspect widely differing conditions and practice. A brief review of some of the conditions may enable American mining men to appreciate more fully the difficulties with which British engineers are faced, and to some extent explain why American, coal can be sold f.o.b. mine at the present time at about 50 to 60 per cent of the cost of British coal at the mine, and why British man-shift outputs fall far below American at present being less than 30 per cent. Bulman gives the average depth of 6-ft. seams. in Britain at 1350 ft., and of 2-ft. seams at 517 ft. George S. Rice states that 90 per cent of American coal 'is taken from less than 600 ft. Much English coal is taken below 2000 ft. and some below 3000 ft. The total influence of depth on cost is not always evident. Room work as known in America becomes less advisable with increasing depth, as pillars crush badly if left -for any length of time. A limited amount of bord and pillar work, taking very small amounts of coal in the first working, takes the place of room work, with rapid working of the pillars as soon as the panels are broken. Ventilation difficulties increase tremendously with depth and thinning coal. In America the chief use of air underground is to dilute gas. In Britain it serves a dual purpose, in many cases the amount of air cir-culated being far in excess of the quantity necessary to dilute gas to reasonable proportions. At great .depths rock temperatures exceed-95 deg. F., and great volumes of air are necessary for rock cooling. At these high temperatures humidity becomes an important factor. At present a great deal of research is under way to find methods of overcoming the troubles experienced with high temperature and humidity in deep mines.

Jan 8, 1928

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

By H. R. Gardner

The heat treatmmt of plutonium was studied using the Jominy end-quenching technique commonly used for determining the hardenability of steel. Plutonium specimens were end-guenched from temperatures in each of the ß, y, d, d') and E phases. One series of specimens with a low-iron content, 165 pprn Fe, and another gvoup with a high-iron content, 678 pprn Fe, were used in order to study the effect of a Pu-Pu,Fe eutectic network on the hardness and micro-structure. Hardness traverses indicated no significant variations in hardness with either cooling rate or quench temperature. Metallographic studies indicated major effects on microstructure. Grain size was found to vary markedly with quenching temperature and cooling rate. It was determined that the Pu-PueFe eutectic network could be modified extensively by heat treatment, including spheroi -dization in the y phase and 6 phase below 413°C. An unidentified spheroidal inclusion was observed to go into solution in the delta and higher temperature phases. 1 HE element plutonium is unique among metals in that it has six allotropic forms in the solid state.' These have been designated' as the a, ß, y, d, d', and phases. The respective phase transformations occur at approximate temperatures of 122", 210°, 319°, 450°, and 480°C with a melting point at 640°C. With this number of phase transformations it becomes pertinent to consider the effect of heat treatment and cooling rate in the various phases on the microstructure and hardness of plutonium. To determine; the effect of a wide range of cooling rates, the Jominy end-quenching technique was applied to cylindrical plutonium specimens. In addition, since the presence of iron in amounts greater than 500 pprn is common in plutonium and results in a network of the Pu-Pu6Fe eutectic, it was decided to study heat treatment effects on two bomb reduced plutonium buttons with different iron contents. A low iron button containing 165 ppm Fe and a high iron button containing 678 ppm Fe were selected for this comparison. EXPERIMENTAL PROCEDURE Experimental Material. The cylindrical bars for Jominy quenching were cast from button stock in vacuo in MgO coated graphite molds. Metal pouring temperature was approximately 950°C and the molds were preheated to 300°C. The castings were machined to 0.5 in. diam. by 2.5 in. long cylinders. Chemical analysis and density data for the two groups of Jominy specimens containing different iron contents are presented in Table I. Except for iron, heats 19-12-1 and 20-2-1 are comparable within the limits of analytical accuracy. Representative specimens from the low-iron and high-iron bars were taken for metallographic examination. The low iron specimen was found to have extensive microcracking, Fig. 1. In addition, numerous unidentified spheroidal inclusions were present, Fig. 17. The average grain size of the low-iron plutonium is 0.068 mm, Fig. 4. In the high-iron plutonium, a Pu-Pu6Fe eutectic network is prominent, Fig. 7. The average size of the network is 0.100 mm. Unidentified spheroidal inclusions were also common in the high-iron plutonium. The average grain size of the high-iron plutonium is 0.036 mm. Experimental Technique. A Jominy end-quenching fixture was fabricated for glove box use. A 2.5 in. water height was used with an orifice of 0.250 in. ID. The orifice to specimen distance was maintained at 0.5 in. Annealing temperatures of 160°, 265°, 400°, 465°, and 535°c were chosen for the study of the effect of quenching from ß, y, d, d', and e phases on microstructure and hardness. During quenching, cooling curves were obtained from the Jominy specimens at distances from the quenched end of 1/16, 1/8, 3/8, 3/4, 1-1/4, and 2 in. Cooling rate calculations were made from the cooling curves for temperature intervals of 100° to 110° 160" to 170°, 330" to 340°, 420° to 430°, and 490° to 500°c. These temperature intervals were chosen

Jan 1, 1962

By John V. Beall

Never having done it before, it took us all day and until 11 at night to select and pack for a four-day back- pack trip up Lake Chelan last month. When we were through, we couldn't lift our own pack and Sylvia's, OUT spouse's, we barely managed to budge. Nevertheless, the next morning we were at the dock to board the Laldy of the Lake for the 3 ½ -hr boat trip to Lucerne. Our dress and accouterments creating the appearance of a veritable expedition into the wilderness made a sharp contrast with our fellow passengers, a senior citizens tour group from Spokane. We had come out to Seattle for the SME Fall Meeting and were taking advantage of the occasion for a vacation trip back to Lucerne and Holden where we had lived briefly 25-years ago, and a backpack trip up Railroad Creek from Holden to the Glacier Peak country, weather permitting. No matter what you say, weather is important, and this is one of the ingredients that went into making the SME Fall Meeting and Exhibit in Seattle, September 22-24, a thoroughly delightful experience for the 700 plus persons who attended. Seattle is a beautiful city, but with late September sunshine, which we experienced, it is the best. The second ingredient, is a swinging host committee. Under the leadership of Don Anderson and Tom Van Zandt, co-chairmen, and Mrs. Cecilia Reed, Ladies Program, superb hospitality and fine arrangements were blended. Earl Beistline, from Fairbanks, organized a two-day short course on arctic operations which preceded the meeting and drew an attendance of 44. Dick Robbins, in charge of arrangements, provided Masters-at- arms for technical sessions and a presentation of the colors by the U.S. Coast Guard at the Welcoming Luncheon. Eric Cheney's field trips ranged far and wide with events both before and after the meeting. David (Jeff) Kroft, capably managed audio-visual operations with a group of students from the University of Washington. Charles Hochmuth worked long, hard and effectively before and during the meet- ing on finances. Hank Reed, managed an authentic three-ring circus as Entertainment Chairman. His activities covered two cocktail receptions for all registrants and a dinner-dance. Dolph Campbell and Joe Hackbarth provided publicity by press and TV (see p. 37-40). SME's meetings have certain characteristics and possibly not all of these are known to everyone. The first of these is the deliberate involvement of the AIME Section in the area of the meeting. Most trade shows and conventions are run 100% by a professional staff and although SME staff could also do this, it has been our experience that a more friendly and better meeting results when the local members apply their talents. Actually SME only considers a site for a meeting after it has received an invitation from a Section. The knowledge of local conditions which Section committeemen bring to a meeting is of great value.

Jan 1, 1971

By J. Van Steveninck, A. C. Pols, R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rock,1,2,3 metal,4,5 and wood6 have been reported to serve various applications. A number of papers have been published on these subject, 7,8,9 some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'.7 Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making holes, only conventional drilling fluids have been considered. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (1 ½ in. ) and full-scale bits (6 ½ -9 5/8 in. ) . In view of the application of jets in deep holes, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids.

Jan 6, 1974

"Power is transmitted to Butte, a distance of 130 miles, over two separate lines running parallel on the same right of way.The transmission line embodies the most approved ideas in construction. The conductors are No. O. B. & S. gauge, hard drawn copper strand. The insulators are of the suspension type, each insulator consisting of six units, 10 inches in diameter. The insulators will stand a wet test of over 300,000 volts, and were selected after long and careful tests by the company's engineers. The wires are carried on steel towers of four-legged, single crossarm type, manufactured by Milliken Bros. The three conductors are suspended in a horizontal row from the crossarm, and there are no transpositions in either line. Above the power wires and symmetrically located are two galvanized steel strands, Vs-inch in diameter, grounded at each tower, which serve as a protection against lightning.The distance between towers in level country is 600 feet. In mountainous country, however, the spans are irregular in length and spans of 1,500 or 2,000 feet are common. The longest one in the line is that crossing- the Missouri River and is equal to 3,034 feet. The length of this span is such that a person standing at one end of it can sec the wires go off and vanish into space, while the tower at the other end is barely visible to the naked eye on a clear day. The towers at one end of this span arc shown in the accompanying photograph. The line starts at an elevation of 3,200 feet, rises to an elevation of 8,200 feet as it crosses the Continental Divide, and again descends to 6,100 feet, the elevation at Butte.Quantity of coppc1· in transmission line, 1,330,000 pounds.Number of towers, 2,-1-00.Steel used in construction, approximately, 2,-1-00 tons."

Jan 1, 1913

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900' to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,' nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.' In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance' present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By L. G. Austin, R. R. Klimpel

This article demonstrates that the Gilvarry and Klimpel-Austin equations for the random fracture of solids are incorrect by deriving intuitively correct expressions for simple cases and showing that the foregoing equations do not reduce to right answers. It is the purpose of this article to point out serious errors in some existing treatments of the random fracture of solids. Gilvarry ' gives the equation where B(y,x) is the cumulative fraction by weight of particles which fall below size y when particles of size x are broken. The constants i, j, k contain shape factors and densities of flaws leading to propagating fracture surfaces. The authors believe this equation to be incorrect. Klimpel and usttin' give where r~ is the number of fracture planes originating from edge flaws (per L where L is the edge length of the original particle), rs is the number of fracture planes originating from flaws on the particle surface (per S where S is the surface of the original particle) and rv is the number of fracture planes originating from flaws within the particle volume. This equation is also incorrect. The failures of these equations will be demonstrated by deriving intuitively correct expressions for simple cases and showing that the Eqs. 1 and 2 do not reduce to the correct answer. In this process, the flaws in statistical reasoning inherent in the derivations of Eqs. 1 and 2 become apparent. THE KLIMPEL-AUSTIN EQUATION Eq. 2 was derived by considering a set number of fracture planes occurring spatially at random within a given particle. This case will be treated here in its simplest form: a line with 1, 2, 3, etc., fractures occurring at random. This is illustrated in Fig. 1, with the original length of the line as Vo. The breakage of a long, thin, brittle fiber is a corresponding physical case, with the volume of a fragment proportional to its length. Assuming independence of the occurrence of the fractures, the probability of any one fracture occurring in length dV is dV/V0. The probability of the first fracture occurring at a length V to V + dV is dV/Vo. For the case of only one fracture per particle, formation of a number-size distribution of the left-

Jan 1, 1969

By H. Y. Hunsicker

A graphic method has been devised for three-di-mensional analysis of hot deformation and for correlating the amount and directionality of the deformation with resulting directional properties. Deformation is evaluated in terms of dimensional change ratios referred to three orthogonal axes. Since all combinations of the three ratios can be represented in a triangular coordinate field with logarithmic scales, a two-dimensional chart of extent of deformation and degree of asymetry is possible. The entire gamut of shape changes from upsetting through flat-rolling to rod-rolling is accommodated. The resulting coordinate system is a base upon which can be represented the properties of the wrought products measured in the directions of the axes employed fir evaluating the deformation. When property data are available for many types and amounts of deformation, a three-dimensional figure can be constructed, and the projection of this figure is referred to as a ''3d'' chart. Experience in using such charts to plan fabricating operations for a variety of thick-section forged and rolled products of heat-treated aluminum alloys has verified its practical value for optimizing directionality relationships. MechANICAL anisotropy of thick section products of heat-treatable aluminum alloys is recognized by producers and users of these products, and the extent of the directional differences is apparent in property tabulations included in handbooks, standards, and specifications.' Attention has also been directed to the existence of important directional differences in the resistance of these products to stress-corrosion cracking. Metallurgical structure factors responsible for these directional differences include, among other possibilities, shape and alignment of grains, voids and nonmetallic inclusions (when present), volume fraction and spatial distribution of secondary phase particles and solid-state precipitates, crystal-lographic textures, and Bauschinger effect. The contributions of the individual factors vary with alloy composition, heat-treated temper, type of working process (forging, rolling, extrusion), and the amount and directional nature of the deformation. In general, the cast ingot used as the starting material for producing these wrought products exhibits only a modest degree of directionality. A monotonic and continuous transition from this nearly isotropic state with progressive hot deformation would appear probable, assuming that the working temperature is sufficiently high to cause continuous dynamic recovery. Several years ago a project was undertaken to evaluate the effects of hot deformation and metallurgical structures on the directionality of thick wrought aluminum alloy products, and the method to be described was developed as an analytical tool in this investigation. DIRECTION NOMENCLATURE The nomenclature system adopted by industry for the three mutually perpendicular directions employed in testing aluminum alloy products includes four terms: "longitudinal", "transverse", "long transverse", and "short transverse". These terms are conventionally related to the external geometry of the product but also by implication to the deformation and resulting metallurgical structure. Occasions arise in which through use of unusual fabricating methods, intentional or otherwise, the structure does not have the usual relationship to external geometry or may be very complex because of inhomogeneity of deformation throughout the piece. The longitudinal direction is generally parallel to the primary rolling direction or to the direction of extrusion. In the case of forging, it is parallel to the direction of maximum extension (not maximum "working" or "flow", as frequently stated). The term transverse is applied to any direction perpendicular to the longitudinal direction in a product having symmetry about the longitudinal axis, and generally, although not always, the deformation to produce these forms is nearly symmetrical in the transverse plane. This term then may be applied to a round, square, hexagon, or other polygonal, symmetrical shape produced by extrusion or rolling or by forging, if produced by a simple, symmetrical drawing procedure. The type of microstructure generally associated

Jan 1, 1970

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, 'mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924

By Harry Udin

IN 1948, the writer and his associates determined the surface tension of solid copper by balancing the force of surface tension in a very fine wire against an external load.' At that time we, in common with other early workers, assumed that grain boundary energy in a pure metal is very small in comparison to the energy of an external surface. Accordingly, we neglected the internal surface energy of the coarse-grained specimens. Since that time, experimental evidence has accumulated showing that grain boundary energy, far from being small, is generally about one-third of the energy of an external surface.2-4 This is sufficient to introduce a significant error into our determination. The differential equation governing equilibrium is: wdl - yds, + y*ds2 [I] rather than wdl = yds as originally written. w is the balancing force in dynes, 1 the length of the specimen, sl the external and s2, the internal surface area, y the copper/ copper vapor surface tension, and y* the grain boundary tension. Fortunately, we had made for another purpose a careful study of the size and shape of the grains, and found that the boundaries, with rare exceptions, traversed the specimens and were perpendicular to the wire axis. For this case, eq 1 leads to w = rry -(n) r2y* [2] where r is the wire radius and (n is the number of grains per unit length. A count of some twenty 5-mil wires indicated that - n became 80 & 10 after a short anneal near the melting point, and remained nearly constant for as long as 96 hr at temperature. An assumption of y* = 1/3y leads to a defining eauation for r: [31 The term in the brackets may be considered a correction factor applied to eq 11 of ref. 1. Upon applying this factor, the surface tension of solid copper at its melting point is found to be 1650 & 100 dynes per cm, rather than 1370 as previously reported.' The new temperature coefficient is —0.55 dynes per cm per "C. Grain boundary energy is more significant than surface energy to the physical metallurgist. It is evident from eq 2 that a series of experiments with wires of different grain size can lead to an evaluation of y*. The details of such an experiment are being worked out now. References 1 H. Udin, A. J. Shaler, and J. Wulff: The Surface Tension of Solid Copper. Trans. AIME, 185, 186-190; Journal of Metals (Feb. 1949) TP 25303. 2 G. L. C. Bailey and H. C. Watkins: Surface Energies in the System Solid Copper-Molten Lead. Proceedings Physical Society. (London) (1950) 36B, 350. 3 L. H. VanVlack: Inter granular Energy of Iron and Some Iron Alloys. Ph.D. Dissertation, Univ. of Chicago, Sept. 1950. 4 . P. Greenough: Grain Boundary Energies in Silver. R.A.E. Report, No. Met. 52. (May 1950) Fan-borough, Hants, England.

Jan 1, 1952

The entire War Minerals Relief Commission heard the case of the Chas. T. Pyrites & Chemical Company of Georgia on April 15 and 16. The Commission insisted on great detail with regard to the entire enterprise, although the main questions seemed to be of the amount involved. It is considered by the Commission that this claim comes unquestionably under the Act, it is one of the best examples that has been brought to the attention of the Government thus far. Testimony showed that operations were done on the property late in 1916 without request from the Government. Preparations were made to work the pyrites deposit on a comparatively small scale but , following a visit from a representative of the Secretary of Interior and a personal interview of the principal owner of the property and Secretary Lane, operations on a much larger scale were begun. The amounts expended prior to this interview were carefully separated from the expenditures thereafter. Testimony showed that it was the intention of the owners to transport their product by motor truck to the railroad-13 mi. away. This limited shipments to about 50 tons daily. Under the enlarged plan taken against the better business judgment of the owners, a railroad spur at a cost f nearly $200,000 was built to the mine. The operation included a concentrating mill with a capacity f 600 tons daily and an expensive dam to make possible the use of waterpower. With these improvements, the company was just beginning, operation under its enlarged program when the armistice was signed. This resulted in a greatly decreased demand and consequently lower prices, with all prospects indicating that the property could not operate profitably when Spanish pyrites begin to move.

Jan 6, 1919

[I-Institute of Metals Division PAUL D. MERICA, Chairman ZAY JEFFRIES, Vice-chairman W. M. CORSE, Secretary General Committee ROBERT J. ANDERSON H. C. JENNISON L. W. SPRING WILLIAN K. FRANK DAVID LEVINGER R. L. SUHL J. R. FREEMAN, JR. PAUL McKINNEY R. F. WOOD]

Jan 1, 1928

By Edward W. Parker

I. INTRODUCTION. AT the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899, I presented a, paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-minim industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is ?shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the United States Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent in 1907 to 37 per cent in 1908. In 1898 only 19.5 per cent. of the total product was undercut by the use of machines. The number of undercutting-machines in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 was almost exactly double that of 1898, while the machine- * Published by permission of the Director of the U. S. Geological Survey. 1 Trans.. xxix.. 400 to 4,59 (1899).

Sep 1, 1910

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925

By Robert T. MacMillan

Of all the mineral substances utilized by man, salt or sodium chloride has one of the longest and most varied histories. Because all animal life is descended from marine organisms, sodium and chlorine became necessary to life, and as sodium chloride meets requirements most readily, common salt has been essential to human and animal diets from earliest times. As civilization progressed, man learned to evaporate sea water and brines of saline lakes and springs to obtain salt, and gradually ceased to depend on the flesh of animals and the occasional salt outcrops or "salt licks" they frequented. He also learned that salt had a multitude of uses, particularly as a preservative of meat and other foods. The importance of salt in the minds of early men may be readily seen from many allusions in the Bible and other ancient writings. Expressions such as "not worth his salt," and "the salt of the earth" are deeply embedded in the English language. Salt has symbolized friendship, fidelity, purity, and hospitality. It has been used as currency; had religious significance; caused wars; and has been a favorite commodity for taxation. The English word "salary" stems from the Latin word for salt, in which Roman soldiers received part of their pay. Although salt today retains its dietary importance, it has thousands of other uses. Of each 100 pounds produced in the United States less than three pounds is for table use. The other 97 pounds goes for agricultural, industrial, and chemical uses. Fortunately, reserves of salt are enormous and reasonably well distributed on the face of the earth. The sea is an inexhaustible source of salt which may be had at prices which vary with climate and other factors. In addition, large underground salt deposits and many salt lakes, springs and playas are scattered throughout the world. Most countries have access to a salt supply, although some are more favored than others. Properties Crystallized sodium chloride or common salt is known as halite. Its molecular weight is 58.454 and it contains, by weight, 39.34 pct sodium and 60.66 pct chlorine. Alternate positions in the cubic lattice are occupied, respectively, by negative chloride and positive sodium ions; the crystal form is isometric. Crystallization from water produces concentric shells, and when broken, a crystal shows conchoidal fracture. Salt has a hardness of 2.5; its specific gravity ranges from 2.1 to 2.6 for rock salt and is 2.165 for the pure crystal. The refractive index is 1.554; it melts at 800.8 ± 0.5°C and boils at 1413°C. Its heat of fusion is 123.59 cal/ gram. Salt is transparent or translucent and highly diathermous. It is colorless when pure and has a vitreous luster. Salt containing traces of iron oxides has varying shades of yellow, orange, brown, pink, or red. The peculiar shade of red sometimes found in that produced by solar evaporation of sea water has been attributed to tiny organisms. Blue mottlings sometimes seen in halite crystals have been attributed to colloidal sodium. Salt is soluble in water to the extent of 35.7 parts per 100 parts of water at 0°C and 39.8 parts per 100 of water at 100°C. The small difference in solubility with increasing temperature is important in the economics of producing salt by evaporating brine. Salt has a negative heat of solution which is 1.281 kg-cal/ mole at 18°C in 200 moles of water.

Jan 1, 1960