Search Documents

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

IN order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.o.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the "straight wash" ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces-namely, low price of product and minimum amount of fines-iron-ore concentration has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. [ ] Table I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1943

By L. Luini, E. Lee

An exploratory survey of the heat treatment response of commercial titanium alloys (Ti-150A, RC-130B, and MST 3AI-5Cr al-loys) shows a wide range of possible hardness and microstructural characteristics. The hardening is primarily dependent on the solid state transformation of the phase. An age hardening reaction which apparently is associated with ß decomposition and precipitation has been shown. Brittleness and notch sensitivity appear to be characteristic of age hardening to high hardness. Ductility, tensile strengths, and elongations are given. A NUMBER of commercially produced titanium-base alloys have been made available by the titanium metals industry. These alloys were developed to combine the light weight of titanium with increased strength through alloy additions. Usually the properties of these alloys are reported for material in the hot rolled and annealed condition. Since the production of commercial titanium has preceded the investigation of titanium-base alloy systems, the potential of these alloys is not well known. Although heat treatability has been indicated for these alloys, data on the response to heat treatment are quite limited. The heat treatability of titanium is based on the allotropic transformation of the high temperature, body-centered cubic ß structure to the low temperature, hexagonal close-packed a structure at approximately 1625 °F. This transformation in the pure metal is of little practical significance in heat treatment since the high temperature phase is not amenable to controlled transformation. Alloy additions serve to alter the transformation kinetics and permit control of the transformation by heat treatment variables. The effects of different alloys on the allotropic transformation in titanium classify them in two general categories,1 a stabilizing and ß stabilizing elements. The a stabilizers, represented by aluminum and oxygen, raise the temperature limits of the low temperature phase and introduce a two-phase a + ß temperature range. The ß stabilizers, represented by molybdenum and columbium, lower the equilibrium temperature of ß and give rise to an extended temperature range where both a and ß phases are stable. Another type of ß stabilizer, represented by iron, chromium, and manganese, introduces a eutectoid reaction. Some commercial titanium alloys belong to complex multiple element systems. Based upon the phase diagrams of the binary systems, the general effect of commercial compositions is to vary the stability of the high temperature phase and significantly alter its transformation characteristics. Therefore it is expected that the characteristics of alloyed titanium can be altered by heat treatment. The present investigation was undertaken to survey the variations in hardness, microstructure, and mechanical properties as affected by heat treatment variables. Commercial Alloys lnvestigated The commercially available titanium-base alloys selected for this investigation and obtained as 3/4 in. diameter hot rolled and annealed bars are listed in Table I. The producer did not determine the chemical composition of the Ti-150A heats X1052 and L685. The early heats of Ti-150A, prefixed with the letter X, were melted with tungsten-tipped electrodes and cast in approximately 500 lb ingots 12 in. in diameter. The heats prefixed with the letter L were melted under a revised melting practice yielding approximately 1300 lb ingots 16 in. in diameter. The final annealing treatment was at 1200" to 1250°F for 1 hr. The MST-3A1-5Cr alloy was melted in an induction furnace and cast in 7 in. diameter ingots. This practice produces high carbon material and some variation in the amount of carbides was found in different sections of the same bar. The RC-130B alloy was melted with a carbon arc. This alloy showed approximately 2 pct carbides. No large segregation effects were observed.

Jan 1, 1955

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By WALTER B. JONES

IN ALABAMA there are three distinct groups of bauxite deposits, as follows: (1) Cambro-Ordovician contact with the principal-deposits located in Talla-dega, Calhoun, DeKalb, and Cherokee Counties, and in adjacent portions of the State of Georgia. (2) Midway-Nanafalia contact, with the principal deposits in Barbour and Henry Counties, and in adjacent portions of Georgia; also in North-eastern Mississippi. (3) Mississippian - Cretaceous contact, with a group of deposits centered around Margerum in Colbert County. For the purpose of more clearly describing bauxite mining in the state, past, present and possible future, these three groups will be described separately.

Jan 1, 1934

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

Phase diagrams for the Ti-W and Ti-Ta systems were determined. The Ti-W system is characterized by a wide, two-phase region of ß plus tungsten which is derived from a peritectic reaction between the liquid and tungsten solid solutions. The ß field terminates in a eutectoid reaction between a titanium and tungsten terminal solid solution. Tantalum and ß titanium form a complete series of solid solutions. Other features of this system are the extensive a-ß field at low temperatures and an appreciable solubility of tantalum in a titanium. BOTH tungsten and tantalum were first thought to form ß-isomorphous systems with titanium as a result of early work' using powder-metallurgical techniques. Later work2 on arc-melted Ti-Ta alloys, made using a commercial titanium base, showed that, in the range of 0 to 10 pct, tantalum was soluble in ß titanium and that the a solubility extended to between 2 and 5 pct Ta at 790 °C. The present investigation covered the entire alloy range in both systems and was chiefly concerned with high-purity alloys at the titanium-rich end. The constitution of titanium-rich alloys made with a commercial titanium base was reported by Holla-day, Kura, and Jackson.3, 4 As will be shown in detail later, the early prediction of a isomorphism was true for the case of the Ti-Ta system, but not for the Ti-W system. The results of this investigation will be presented first. The experimental methods used are described in the Appendix. Ti-W System The entire Ti-W phase diagram is shown in Fig. 1. Details of the titanium-rich side are shown in Fig. 2. The chief features of the system are a ß eutectoid and a high-temperature peritectic between liquid and tungsten solid solution. Melting Range: Examination of cast structures of low and medium-tungsten-content ingots showed cored ß phase as the primary constituent. Fig. 3a illustrates a typical cast structure for alloys in the range of 20 to 30 pct W. From 30 to 72 pct W, coring was very severe. Alloys containing 72 through 88 pct W, however, showed definite evidence of a peritectic reaction between the liquid and a terminal solid solution of titanium in tungsten. Fig. 3b shows the cast structure for an 80 pct W alloy. A 95 pct W alloy, shown in Fig. 4, consisted primarily of primary tungsten solid solution plus a small quantity of ß probably rejected during cooling. Incipient-melting experiments located the peritectic temperature between 1850" and 1900°C and indicated that the reacting phases are liquid containing about 25 pct W and tungsten terminal solid solution containing about 8 pct Ti. Figs. 5 and 6

Jan 1, 1954

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970

By I. H. Warren, E. Devuyst

A review of the physical and chemical aspects of the direct leaching of metal oxides has been given and com- pared to recent data of the authors and co-workers. The physical aspects, including the anisotropy of the dissolution, the hydration and the zero point of charge of some metal oxides are discussed first and then the kinetics of the dissolution of metal oxides are considered. A general mechanism of the leaching of oxides which describes most of the observed results is proposed.

Jan 1, 1973

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927

By JOHN R. SUMAN

OVERWHELMING proof of the importance of oil in a modern national economy is afforded by the present European War. Treat¬ies and national boundaries have been cynically violated to secure greater supplies of the precious fuel. Petroleum substitutes have been desperately, and far from successfully, sought. The whole German military theory of the drang nach Osten, the drive to the East, is directed at cutting the British supply of oil and securing a supply for Germany. This is a war of machines, and the machines of war feed hungrily on oil. In view of this fact, it is surely comforting to know that we are living today in a nation which has surpassed all the rest of the world not merely in unearthing the raw supplies of petroleum which lie beneath its surface but also in every phase of the industry in mining, refining, processing, production, and distribution.

Jan 1, 1941

At the meeting of the Board of Directors held on October 25, the reports of the Treasurer and the Nominating and Finance Committees were received. Thirty-five members, seven associates, and six junior associates were elected; one change of status front junior associate to member was granted; six members were reinstated; and one resignation was accepted. An extension of' time was granted to fourteen members. The dues of forty-seven members were suspended on account of their being in active service. The application for formation of a Houghton Section was granted and the president was authorized to appoint a committee on organization. The courtesies of the Institute were extended to visiting engineers of France, Great Britain and Italy who are at present in the country on war missions. Votes of thanks were extended to the Committees of the .Milwaukee meeting. The proposed Survey of Engineering Organizations by Engineering. Foundation was approved. The Secretary was authorized to publish in the Bulletin an appeal from the American Ouvroir Funds. A petition signed by 110 members of the-Institute to change the name of the Institute was presented. Treasurer George C. Stone resigned on account of contemplated absence from the city, and George D. Barron was elected Treasurer in his place. Mr. Alexandre Gouvy, a distinguished French engineer, then addressed the Board.

Jan 12, 1918

By T. H. Alden

In several recent studies of fatigue fracture in single-phase metals, tests have been made using the condition of essentially constant plastic strain amplitude.1-4 This procedure departs from the more common practice of holding the amplitude of stress constant. From these studies have emerged two important generalizations about the behavior of metals during cyclic straining. First, measurements of the stress amplitude, required to impose the fixed plastic strain amplitude, have shown that the rate of cyclic strain hardening in annealed metals is rapid in the early cycles but decays quickly to a very low value.1"5 This behavior is displayed particularly for a range of strain amplitudes below about 2 pct and at low and high temperature. Frequently, the hardening rate becomes so low that one can determine a "saturation" stress. This stress increases with strain amplitude. In addition, an experimental relation between fracture life and plastic strain amplitude was obtained by Coffin and Taternelli,' namely N 1/2 ep = constant. For several metal:;, this equation has been shown to hold down to a strain amplitude of 0.1 pct. Whether it also holds in the "low amplitude" range (lives of more than about 105 cycles) has not been established. The importance of the saturation stress level (a value derived from strain hardening measurements) to the question of fracture life (the usual quantity of interest of fatigue testing) lies in the observation that cracks start to form when the cyclic hardening rate is essentially zero, and not before.4"5 This point suggests immediately a means of relating tests at constant stress and constant strain amplitudes. When making comparison, the stress in a constant stress test is to be identified with the saturation stress in a constant strain test. If these ideas are correct, then it should be possible, using the relation between fracture life and strain amplitude and experimental curves of saturation stress versus strain amplitude, to predict the fracture life as a function of stress, i.e. predict the S -N curve, for low stress fatigue. Saturation stress amplitude-plastic strain amplitude data, obtained in tension-compression, exist only for a few metals and for relatively high amplitudes of strain. Comparable S -N curves (push-pull loading) were known by the author only for OFHC copper. Values for this metal taken from Ref. 2 are shown in Fig. 1. The strain amplitudes, the lowest

Jan 1, 1962

By Ursula E. Wolff

The precipitation of carbides from an alloy containing 33 pct Ni, 21 pct Cr, balance iron, was investigated electron microscopically by means of extraction replicas and thinned metal foils. Annealing temperatures ranged from 565°to 870°C and up to several thousand hours. M23C6 precipitated in pain boundaries, incoherent and coherent twin boundaries in that sequence. The orientation relationship between carbides and austenite matrix was determined and correlated with the morphology of the carbides and with the type of boundary in which precipitation occurred. In large-angle grain boundaries, as well as in coherent twin boundaries, the carbides had the same orientation as one of the adjacent pains. These carbides formed sheets of individual flakes with shapes related to the orientation of the boundary. In incoherent twin boundaries carbides precipitated in ribbons composed of pavallel rods. An unidentified subcarbide was found to precede precipitation of M23C6 in these boundaries. The M 23 C6 rods had a kind of fiber texture with (110) parallel to the long dimension of the rods and ribbon, and with orientations of both of the adjacent twin-related austenite crystals Predominant in the texture of the carbide. A hard sphere crystal model has been used to discuss orientation and morphology of the carbides in terms of free volume and vacancies available in the boundaries. A number of papers have dealt with the morphology of chromium carbide (M23 C6) precipitated in austenitic stainless steels.1"7 In all these investigations, the carbides were examined in the electron microscope by means of extraction replicas. With this technique, the carbides retain the spatial distribution they had in the bulk sample. However, since the matrix is dissolved in the process, the particles can turn in an unpredictable way; and the orientation relationship between matrix and carbides cannot be established. In this paper the results of studies on extraction replicas and on thinned metal foils are reported. These studies were undertaken to determine the matrix-to-car bide orientation relationship, and to correlate the orientation of the carbides with their morphology. PROCEDURE The material used was an austenitic alloy with 33 pct Ni, 21 pct Cr, balance iron, containing approximately 0.05 pct C. Coupons of 1.25-mm sheet were first solution-annealed at 1050°C for 15 min and air-cooled. Then, to precipitate the carbides, samples were isothermally annealed in the range from 565" to 870°C for times up to several thousand hours. All further specimen-preparation procedures were carried out after the final anneal. Carbon extraction replicas from polished and etched surfaces were made with 10 pct bromine in methyl alcohol.' Thin foils were prepared from punched-out 3-mm-diam disksg which fit into the electron-microscope holder. The disks were prethinned by grinding to approximately 0.5 mm thickness, and then electro-polished in a polytetrafluoroethylene holder1' with a solution containing 5 pct perchloric acid in acetic acid to which 10 g per 1 Cro3 and 5 g per 1 nickel chloride were added (etchant modified from that of Briers et al."). This solution dissolves neither the carbides nor the austenite around the carbides preferentially. By using extraction replicas, electron micrographs and selected-area electron-diffraction patterns were taken from the same carbide arrays. By using thin foils, electron micrographs were made from a grain boundary area containing carbides. Electron-diffraction patterns were then taken from the same area and from each of the adjacent grains separately. In this manner, the orientation of each grain could be determined without interference by the carbide pattern. A peculiarity of extraction replicas should be pointed out. After the matrix is etched away, the carbide arrays float freely in the etching and washing solutions, and are held in place only at the anchoring points in the carbon replica. When the replica is picked up with a screen the carbide arrays tend to flip to one side. Thus, while the surface features are preserved, the original arrangement of the carbides may severely and unpredictably be disturbed whenever the specimen contains large amounts of interconnected carbides. Nevertheless, it is possible to correlate the different morphologies of the carbides with the type of boundary in which they have precipitated. RESULTS 1) Extraction Replicas. Fig. 1 shows that the grain boundaries usually are curved, multicornered surfaces of random orientation. The coherent twin boundaries (which are (111) planes) cut a grain into parallel slices. Incoherent twin boundaries occur at the ends and on the steps of twins and are often narrow, parallel-sided strips which are much longer than they are wide. Different morphologies can clearly be distinguished for the M23Ce carbides precipitated in each of these types of boundaries, and agree well with those observed by kinzel.2 The kinetics of this precipitation has been investigated." The first carbides precipitate in junctions of three grain boundaries and fan out from there into the adjoining boundary surfaces, Fig. 2(a). These carbides are oriented randomly, Fig. 2(b), and become coarser and thicker as annealing time increases. The large-angle grain boundaries are next to fill

Jan 1, 1967

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By T. J. Bosworth

The effect of hydrogen pretreatment of alumina, magnesia, and zirconia crucibles on reduced oxygen levels in iron charges has been studied. Hydrogen treatment of commercial high-purity magnesia crucibles was observed to produce as high as 70 pct reduction in oxygen content in iron melts. Hydrogen treatment of the commercial high-purity grade zirconia crucibles produced a 25 pct reduction in oxygen levels in iron melts. An average reduction of Knoop hardness of 47 pct was recorded on the iron charges melted in hydrogen-treated crucibles. On the basis of the experiments and the free-energy diagram, it appears that the major source of reducible oxygen to the iron charge is the suboxides and impurity oxides rather than the major oxide of the crucible. Suitable pretreatment of the crucibles to reduce and remove these oxides yields low oxygen levels in iron melted in the crucibles. DURING the last decade, attempts to produce more pure and uniform alloyed metals have brought about the development of many new melting techniques. Notable among these are vacuum-induction melting, inert and consumable-electrode melting, the cold-mold technique, and numerous techniques for removal of impurities by chemical reaction. However great the achievements in this field, metals must still be melted in contact with media of varying reactivity; i.e., gas, ceramic, and slag. Studies have been made to attain an understanding of the reactions that take place during melting, including slag-metal reactions and equilibria, equilibrium of hydrogen and water vapor, and carbon dioxide and carbon monoxide with oxygen in molten iron. These reactions have been treated quite thoroughly. There is one condition, however, that has been widely overlooked, and, to the author's knowledge, only cursive investigation has been made of it. This is the reaction between the ceramic crucible material and the iron charge. In recent years, Hadley and Bianchi' made a series of studies on hydrogen deoxidation of iron in magnesia crucibles. Bianchi2 studied crucible-FeO equilibria in the temperature range 1525°to 1650°C in high vacuum with, however, inconsistent results. Richardson and Jeffes3 in their series of articles on thermodynamic reactions in the making of iron and steel refer to Wentrup and Hieber's4 work on iron and aluminum deoxidation. Their pork included melting iron in alumina crucibles and measuring the aluminum and oxygen content in the iron. Because of the low values obtained, question has arisen of their analytical accuracy.3 Dastur and chipman5 obtained values on hydrogen-oxygen equilibrium in molten iron contained in alumina crucibles similar to those obtained in experiments in the present program. Hochmann6 studied removal of impurities in chromium irons in high vacuum. His results with respect to oxygen level in chromium-iron melted in magnesia crucibles are consistent with results we have obtained.

Jan 1, 1959

By Lyall Zickrick

As a result of the studies on recrystallization and crystal growth made in this laboratory, certain theories have been developed. These are expressed briefly in a paper by Dean and Hudson.1 One of the principal points brought out in that paper is that in the deformation of a crystal, the energy supplied is distributed to the atoms of the lattice, probably by the forced formation of molecules. It is found that a Maxwellian distribution of the energy among these atoms will account for the grain growth at various temperatures. According to such a distribution the number of atoms with energy above a certain critical value, E, necessary for recrystallization at the absolute temperature T is given by n Ne(-E/kT) where N is the total number of atoms. It is apparent that if this line of reasoning is correct, a metal which has been cold-worked and reheated to a temperature below that of complete annealing will have the atoms with the higher energy recrystallized, that is, reduced to normal energy and there will remain only atoms below a certain energy. If this metal is again cold-worked the peak in the number-energy distribution curve will be displaced toward the regions of lower energies, that is, higher temperature of recrystallization. By a repetition of this process the position of this maximum and hence the recrystallization temperature of the metal could be raised considerably. In order to' check this theory, experiments have been made on copper wire. The wire was drawn from 1/4-in. rod to 22 B & S gage and then sample lots were annealed at 400 and 220° C., respectively. The wire annealed at 400° C. gave an elongation of 34 per cent., whereas that annealed at 220° C. gave only 23 per cent. These wires were then drawn by identical practice to 34 B & S gage and the elongation determined after an anneal of 3 mm. in an oil bath held at various temperatures.

Jan 1, 1927