Search Documents

BURKE BAKER, Philadelphia, Pa. (written discussion*).-The small briquetting plant of the American Briquet Co., at 25th Street and Washington Ave., Philadelphia, was built primarily as a demonstration plant. Its output per hour is 4 tons of 2-oz. briquets, which have been retailed in the, vicinity during the year the plant has been in operation. They have proved very acceptable for use in ranges, heaters and grates in-home, and in steam heating plants in apartment houses and hotels. They have not been sold for power purposes, although satisfactory tests have been made in. this field. Anthracite silt is used and is shipped direct from breaker or washery, the only preparation it receives being the removal f excess moisture by means of a Ruggles-Coles rotary dryer. Care is taken, however, to purchase silt containing less than 18 per cent. ash. The method is covered by U. S. Patent No. 941454, issued to Chas. E. Hite, and is known as the "emulsion process." The binder, which is the, basis of the patent, is composed. of 0.5 per cent. cornstarch or wheat flour; 1 per cent. asphaltum or hydrolene, and 6.5 per cent. water, on the weight of coal dust. It is prepared in a tank equipped with paddle agitators and heated by steam jets. The starch and water are first made into a paste by being brought to the boiling point with live steam; the melted asphaltum is then introduced and thoroughly beaten into the paste by the agitators. This rapid stirring breaks. the hot asphaltum into minute particles which are distributed through the paste, producing a smooth chemical emulsion. This emulsion, when dried, is not soluble in water. The binder is mixed with the dry coal dust in a horizontal paddle mixer, 8 per cent. binder to the weight of coal being used. The resultant plastic mass is then discharged into the press, which is of the simple roll type. Since the binder is a liquid and is not sticky or gummy until

Jan 3, 1918

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

Henry LOUIS, London, England (communication to the Secretary) : Prof. Richards's paper has impressed me as highly valuable. Without entering upon any discussion of it as careful and thorough as it deserves, I venture to mention one or two points which a perusal of it has recalled to my mind in connection with my own study and practice of ore-dressing. I always mentally divide jigging into two phases: 1. A particle at rest on the jig-bed is lifted and carried upwards by the rising current of water, at an increasing velocity, which tends to a maximum. When the upward current is stopped, the particle continues to rise with rapidly diminishing velocity until it comes to rest. This completes the first phase. 2. In the second phase, the particle falls from its position of rest with an increasing velocity which tends again to a maximum, and continues to fall until the rising current of water has reduced its velocity to zero. This completes the second phase. The second phase will evidently be greatly modified by the effect of suction, as Prof. Richards shows; but I do not see that his experiments very clearly imitate the action of the second phase. And the brief intervals at the end of each phase, when the mineral particle, by reason of its acquired velocity, is still moving, though in opposition to the water-current, yet remain to be investigated. I feel especially, in Prof. Richards's paper, a difficulty which I have felt with regard to all similar previous investigations, namely, that the experiments deal with particles falling a long distance, when the velocity becomes uniform. I question whether this uniform maximum velocity is attained in actual jigging-practice. If so, it is certainly for a comparatively very small proportion only of each stroke. It seems to me that an investigation like that of Prof. Richards, but confined to the first 6 or 8 inches of fall only, and carried out with suitably delicate recording-apparatus, is what we

Jan 1, 1895

Howard N. Eavenson, Gary, W. Va. (communication to the Secretary*):—For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting to the Institute my results in the form of a discussion. It has long been a matter of common opinion among mining-men that mine-explosions are more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more inclined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what otherwise probably would have been small explosions. To show the difference in mine-conditions during summer and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas coal-region, in McDowell county,w.Va., the first one being a shaft-mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jan 1, 1910

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior's Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By L. O. Howard

THE CHAIRMAN (WALTER DOUGLAS, New York, N. Y.).--I presume, gentlemen, that Mr. Howard's experience with the Great Falls basic-lined converter has been as regards the tonnage produced from a single lining, perhaps, a world's record. About 6 months ago Mr. Howard shut down and tore out what was left of the first basic-lining which was installed at the Old Dominion, the lining having produced something over 70,000,000 lb. of copper. This was due probably not only to the very excellent grade of the matte which was produced by the smelter there,

Jan 12, 1916

By William Sharp

DISCOVERY of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silverlead mines in the United States. They have a production record of more than fifty-one million dollars.1 After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. GEOLOGY Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 [THICKNESS, FI ORDOVICIAN Pogonip limestone (upper part). Thin bedded limestone with some chert. UPPER CAMBRIAN: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425+ Dunderberg shale. Shale (clay and calcareous shale) and thin bedded limestone340+ Hamburg dolomite. Dolomite and limestonegoo+ MIDDLE CAMBRIAN: Secret Canyon shale. Shale and thin-bedded limestone1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings 335 MIDDLE (?) AND LOWER CAMBRIAN: Eldorado dolomite. Dolomite and limestone2,000 LOWER CAMBRIAN: Prospect Mountain quartzite. Quartzite with occasional inter calated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quart zite proper-I,460+ft. Total thickness6,695+] Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1947

[Appalachian Petroleum Section: Chairman: Robert H. Edele, 1st V.C.: Robert Vutech, 2nd V.C.: Robert Tullis, Sec.-Treas.: Frederick T. Solomon. Meets last Tuesday of each month in Charleston, W. Va. Balcones Section: Chairman: Dr. Frank W. Jessen, 1st V.C.: Gilbert M. Andreen, 2nd V.C.: Lloyd N. Johnson, Seo.-Treas.: W. C. Vercellino. Big Horn Basin Subsection: Chairman: B. E. Yester, 1st V.C.: Robert J. Woodhall, 2nd V.C.: Herbert A. Koch, Secretary: Dean Costello, Treasurer: Thomas W. DeLong. Meets 2nd Wednesday; alternating between Cody and Worland. Billings Petroleum Section: Chairman: George O. Ellis, 1st V. C.: Robert L. Spottswood, 2nd V. C.: Robert M. Watkins, Sec-Treas.: Joseph H. Bato. Meets 5:30 p.m., 3rd Tuesday at Billings Press Club.]

Jan 1, 1961

By Walter Stern

THE self-potential or spontaneous polarization method is one of the oldest in the field of electrical exploration. When applied in prospecting for ore bodies, it is one of the most rapid and inexpensive means of locating indications of ore bodies at shallow depth. Usually, the procedure is to survey the equipotential lines of the electrical field that is generated by the electrochemical activity of the ore near the ground-water level, and to localize the so-called negative centers or points of greatest negative anomaly. Another field procedure involves the measurement of potential differences along potential profiles, generally laid out at right angles to the assumed strike. Again, in such survey, the basis for establishing the presence of ore is the location of negative potential anomalies. The earlier writers on the subject, notably Schlumberger1 and R. G. Wells,2 did much to clarify the fundamental electrochemical phenomena involved. Interpretation of the field data, however, remained largely qualitative. In 1925, A. Petrovsky3 analyzed the relation between the shape of the potential anomaly curve and size and depth of an ore body by assuming the subsurface body to be a polarized sphere.4 Along similar lines of approach, Edge and Laby5 considered the ore body a dipping sheet with limited extent in the direction of strike, while Poldini6 based the theory on the assumption of a dipping bar. The following study endeavors to enlarge [ ] FIG. I.-ORE BODY CONSIDERED AS DIPOLE upon these earlier investigations and attempts, on the basis of the potential distribution of a polarized bar, to indicate certain characteristics of the anomaly curve that make possible the determination of depth, size and dip of a subsurface body. THE SPONTANEOUS POLARIZATION FIELD SET UP BY AN ORE BODY If a sulphide ore body is subjected to oxidation varying in degree in its upper and lower parts according to the difference in the concentration of oxygen within the surrounding medium, an electrical potential field is set up. The form and distribution of this field will be investigated herein with special reference to its components on the earth's surface. Under the simplifying assumption that the ore body may be considered as a dipole with the point sources QI and Q2 situated at its upper and lower ends (Fig. I), the potential of the spontaneous polarization at point P is given by the following equation:

Jan 1, 1944

By C. F. Cockrell, K. K. Humphreys, H. E. Shajer

It is quite conceivable that the question of using coal or an alternate fuel in the future by large industrial consumers may be decided on the basis of possible profitable utilization of flyash. Accordingly, the Coal Research Bureau at West Virginia University has been attempting to develop new uses for this waste material. This effort has resulted in the development of a process for producing flyash-based face brick and other structural materials which generally exceed published specifications for competitive clay-based materials. These structural materials, containing up to 97% waste coal ash, can be produced from flyash derived from most coals without regard to the physical or chemical properties of the coal ash. Preliminary production cost estimates indicate that face brick can be manufactured at a rate of 9000 brick per hr or more with a resultant gross profit of over $24.00 per thousand brick. Plant payout time for a plant of this size would be only about 1.2 years assuming a market price of approximately $55.00 per thousand, a well established figure for comparable clay brick. With flyash production expected to more than double in the next 15 years, there is an increasing need for a practical and Profitable method for the utilization of large tonnages of this material (see Table I listing total flyash production of utilities in each state of the U.S.). Present industrial and governmental physical and chemical restrictions, particularly for use as a lightweight filler or pozzolanic material, have limited the use of flyash considerably. For those ashes which have met the required standards, utilization is not always assured because of lack of promotion and poor public acceptance. Less than 6% of the total flyash production in the U.S. was sold in 1962. The remainder was dumped in disposal areas at costs as high as $2.42 per ton.' It is quite conceivable that in the near future the question of using coal or an alternate fuel by large industrial consumers may be decided on the basis of the possible utilization of flyash. To help insure future coal demands, the Coal Research Bureau at

Jan 1, 1968

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By F. H. Deily, D. S. Rowley, R. J. Howe

By Charles M. Brinckerhoff

When I first went to Arizona in 1925, mining was primarily an underground job. Ajo, Sacramento Hill in Bisbee and Jerome were the only open pit operations in the state. Thousands of men, however, were employed in underground mining at Morenci, Miami, Inspiration, Globe, Ray, Bisbee, and Superior. The grade of ore in the larger operations was about 1-1/2% copper while a few of the smaller ones mined ore better than 2% Cu. In Utah, the Bingham pit was doing well and growing; in Montana, the vein mines of Butte still yielded ore running 6% Cu.

Jan 3, 1972

By J. M. Morkowitr

A. Sawatzky (Atomic Energy of Canada, Ltd.)—The detailed criticism by Markowitz of my simple treatment of the thermal diffusion of hydrogen in Zircaloy-2 indicates that my paper was not as lucidly written as it could have been. I would therefore like to reiterate several of the main points of my proposed mechanism and describe in more detail some of the features only implied in the original paper. The distribution equation derived in my paper was stated to hold only for the case where the volume taken up by the hydride was small compared to the volume taken up by the solid solution phase, subsequent work, mentioned below, having shown it to be out by only a few percent up to a hydrogen concentration of about 3000 ppm. Of course, hydrogen in the two-phase region alone is not conserved in my treatment as pointed out by Markowitz. On the contrary, one of the important features of my proposed mechanism is that in the presence of a temperature gradient a two-phase region cannot exist over the whole specimen. For example, if the specimen is entirely a + 6 initially, then on application of a temperature gradient, a single phase (a) region at the hot surface develops from time t = 0 onwards. As mentioned in my original paper, the interface between the a and a+d regions moves toward the colder surface of the specimen with a discontinuity in hydrogen concen- tration developing at the interface and increasing with time. This interface moves at such a rate that hydrogen in the specimen as a whole is conserved. It must be pointed out that my distribution equation (Eq. [5] in Markowitz's paper) holds only for linear geometry. It is easy to show that for the cylindrical geometry of Markowitz the assumptions used in my treatment lead to

Jan 1, 1962

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By AIME

After an adventurous past-four changes of government in thirty years -the whole of Silesia and attached coal territories have become part of the Polish State. The coal resources of this area are the biggest among the European countries. Under a surface area of 5700 sq km are about 100 coal seams, with a total thickness of 150 meters. According to German estimates, there are some 150 billion metric tons of coal ranging in thickness up to 14 m within a depth of 1500 m. The seams are mostly level, free from faults, with good top and bottom; the coal is of excellent quality, hard and clean; and mining conditions are favorable. The mines are worked at considerable depth by means of vertical shafts and operate with cage and skip hoisting. Before the war, the mines were up to date, equipped with modern machines. Among the European countries, output per man shift was the highest ? 1.9 to 2.1 metric tons ? and cost of production was the lowest.

Jan 1, 1949