Search Documents

C. P. BOWIE, San Francisco, Cal.-In my work with the U.S. Bureau of Mines, I have been detailed to report on oil storage containers, and in going around the country I have, been much interested in, the possibilities in the use of concrete for such containers. In talking with a good many people, I have discovered that concrete is being used A good deal for a wide variety of oils ranging from 14° to as high as 40° Bé., especially, by some of the western railroads:, If any member has had experience, in storing gasoline in concrete, I should like to learn of it. DORSEY HAGER, Tulsa, Okla.-Mr. M J. Munn, formerly .with the U. S. Geological Survey, acid connected with the Gypsy Oil Co., until a short time ago, has invented a invented a method for the application of concrete to the storage not only of crude oil but of refined products:. The Cosden Oil Co., of Tulsa, is now working on that plan, and, expects to store refined products in concrete tanks. THE CHAIRMAN (I.N. KNAPP, Ardmore Pa.).-I have had considerable experience in building masonry tanks for gas Holders. I do not believe it is possible to build a concrete or masonry tank of any kind. With hydraulic cement, mortar, which will be absolutely water-tight, unless the bottom and inner wall, after completion are waterproofed with some impervious material. The same will be true of oil tanks, the bottom and inner face of which must be made impervious to oil. Masonry tanks are intended to be sunk in the ground. All that the wall of the tank then amounts to is a retaining wall to keep the excavation in shape and to receive an impervious coating. The bottom of, a; tank, when empty, must be protected by a relief valve from any hydraulic: pressure acting from below. At ordinary prices, for sheets, a tank 100 ft. diam by 20 ft. deep can be built of steel much quicker and cheaper than of masonry. Several years, ago I saw very large oil storage tank under construction in California the bottom and sides being concrete. The sides were, sloped at about the single of repose for the material excavated: If you build a steel oil tank, you can get. .men for the work who do nothing else, and you, are likely to get a satisfactory job; but if you wish to build a concrete or masonry tank it is almost: impossible to find men skilled in building absolutely water-tight masonry Work. The general idea is that any laborer can mix up concrete in any old way and make a,

Jan 1, 1918

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after it has been pulverized to pigmentary size. The current world production of iron oxide pig¬ments is estimated by the author to be between 450,000 and 550,000 tons based on 1969 data. The fact that highly colored natural deposits of iron ore are found throughout the world ac¬counts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments pro¬duced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970). Nomenclature With the increasing importance of the syn¬thetic iron oxides it is necessary to make a distinction between the natural or mineral pig¬ments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a com¬mercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pig¬ments. Natural pigment ore sources are se¬lected for their special physical-chemical prop¬erties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pig¬mentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1975

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By H. M. Morse

Mississippi, during the year 1941, experienced the greatest diversity of oil activity since the beginning of oil interest in the state—core tests for exploration, core tests for sulphur, continued drilling at Tinsley for production, and wildcatting, which brought to light two new oil fields and two new salt domes. There were 45 wildcat wells drilled in 1941, which showed greater results and findings geologically than the 85 drilled in 1940. Tinsley Oil Field (Yazoo County).—The Tinsley oil field, with its boundaries fairly well defined now, is 8 miles long and 3 miles wide at its widest point. During the past year 213 producing wells were completed, which brought the total number of producers in the field by the end of 1941 to 325 wells. Seven producing sands have been logged, with a total average thickness of 30 ft. of oil sand. The producing formations are the Selma, Eutaw and Tuscaloosa. The average total depth of the wells is 5012 ft. The average gravity of the oil is 35.4°. Production for 1941 was approximately 15,500,000 bbl. of oil. Vaughan-Pickens Oil Field (Yazoo County).—At the end of 1941 only three wells were Producing in this field, the fourth having been abandoned. The total production for the field for the year was approximately 250,000 bbl. of oil. The producing sand is the Wilburn, in the Eutaw formation. Cary Field (Sharkey County).—The British American Oil Producing Co. completed, on Sept. I, 1941, its F. B. Houston No. A-I well, sec. 23, T. 11 N., R. 7 W. It is

Jan 1, 1942

By H. M. Morse

Mississippi, during the year 1941, experienced the greatest diversity of oil activity since the beginning of oil interest in the state—core tests for exploration, core tests for sulphur, continued drilling at Tinsley for production, and wildcatting, which brought to light two new oil fields and two new salt domes. There were 45 wildcat wells drilled in 1941, which showed greater results and findings geologically than the 85 drilled in 1940. Tinsley Oil Field (Yazoo County).—The Tinsley oil field, with its boundaries fairly well defined now, is 8 miles long and 3 miles wide at its widest point. During the past year 213 producing wells were completed, which brought the total number of producers in the field by the end of 1941 to 325 wells. Seven producing sands have been logged, with a total average thickness of 30 ft. of oil sand. The producing formations are the Selma, Eutaw and Tuscaloosa. The average total depth of the wells is 5012 ft. The average gravity of the oil is 35.4°. Production for 1941 was approximately 15,500,000 bbl. of oil. Vaughan-Pickens Oil Field (Yazoo County).—At the end of 1941 only three wells were Producing in this field, the fourth having been abandoned. The total production for the field for the year was approximately 250,000 bbl. of oil. The producing sand is the Wilburn, in the Eutaw formation. Cary Field (Sharkey County).—The British American Oil Producing Co. completed, on Sept. I, 1941, its F. B. Houston No. A-I well, sec. 23, T. 11 N., R. 7 W. It is

Jan 1, 1942

By T. E. Davidson, C. G. Homan

This report deals with a study of the effects of extreme hydrostatic pressure on a polycrystalline material which exhibits a high degree of elastic anisotropy. Metallographically prepared polycrystalline bismuth samples were subjected to pressure levels up to 20,000 atm in a piston type gas-liquid system. The observed structural changes consisted of deformation localized along the grain boundaries, which appears to be a boundary migration phenomena, and widespread slip and cross slip. Subsequent deformation is progressive with increased pressure, and is substantially different in type from the deformation characteristic of uniaxial compression. A large amount of interest has been shown in recent years in the effects of extreme pressure on metals. In this connection, many investigations into the effects of pressure on physical and mechanical properties and reactions have been undertaken. Due primarily to the experimental difficulties involved, there has not been a great deal of study of the structural changes resulting from exposure of metals to extreme pressure. It has been difficult, for instance, to produce a true hydrostatic stress state in many of the extreme pressure devices used, and also to directly examine specimens metallographically before and after pressurization. The results of a preliminary investigation into one of the effects of extreme pressure, and its associated true hydrostatic stress state, on the structure of metals are discussed herein. Metals exhibit varied degrees of anisotropy in their physical and mechanical properties. Significant among the anisotropic properties is the modulus of elasticity, which varies by a factor of as much as three in some of the fcc metals, and by much larger factors in some of the less symmetrical elements. As a result of the variation of the modulus of elasticity with crystallographic direction, shear stresses will be induced in polycrystalline samples under true hydrostatic compression. Depending on several factors, these shear stresses could become of suffi- cient magnitude to cause localized plastic deformation. Presented herein are some of the structural changes observed in polycrystalline bismuth as a result of exposure to hydrostatic pressures of up to 20,000 atm. Although several other materials in both bicrystal and polycrystalline form are also currently under investigation, bismuth was chosen initially, due to its low symmetry and moderately high degree of anisotropy in the elastic properties. The fact that extreme hydrostatic pressure can induce structural changes in some elements in the polycrystalline state is of importance in itself. However, it may also be a factor in many of the other extreme pressure effects. For instance, this localized plastic deformation could substantially lower the recrystallization temperature, thus altering the effects of extreme pressure on this phenomenon. Also, as commented on by ridgman,' the hysteresis in the polymorphic transition of polycrystalline bismuth under extreme pressures could possibly be attributed to structural changes brought about by unequal compressibility. Therefore, to accurately determine the true effects of extreme pressure on metallic substances, one first must determine if any structural changes due to hydrostatic compression are also simultaneously occurring. The purpose of this work has been to determine whether the shear stresses induced by hydrostatic pressure in an anisotropic polycrystalline material, such as bismuth, could reach a magnitude great enough to cause plastic deformation and to study the resultant structural changes and effects. THEORY In a metallic crystal, the elastic properties are dependent upon the crystallographic direction and plane. Depending upon the degree of anisotropy of the elastic properties and other factors, internal shear stresses of sufficient magnitude to cause localized plastic deformation may be induced in polycrystalline material by true hydrostatic compression. The following highly simplified two-dimensional model of two adjacent grains in a polycrystalline aggregate under hydrostatic pressure serves to schematically demonstrate how these shear stresses arise in an anisotropic material.

Jan 1, 1963

At a large meeting of the members of the American Fund for French Wounded it which Mr. Franklin D. Roosevelt presided and at which Mrs. B. Girault Lathrop, President of the Paris Administration A. F.F. W., gave a most interesting address, special rows of seats were reserved for the members of the W. A. A. I. M. E. Those who were unable to be present will be glad to hear that Mrs. Lathrop complimented our organization on having supplied the largest dispensary operated by the A. F. F. W. and the Red Cross in northern France. The A. F. F. W. is going to erect an American Memorial Hospital at Rheims and it is hoped that the one hundred beds in the hospital will be endowed in memory of the men who gave their lives for the liberty of the world. It will be possible not only to endow beds, for which sums of $6000 each are needed, but also to give, as. memorials, sun- parlors at a cost of $10,000 each, two roof gardens at $5000 each, a laundry at $10,000 and a garage at $10,000. The New York Section has undertaken to endow a heel in memory of members of the A. I. M. E. who gave their lives in the Great War. Perhaps other Sections or groups of Sections may wish to do the same thing, or if no other Section cares to assume so much responsibility possibly individuals may like to join the fund already growing in New York, in which case they should send their contributions to Mrs. W. Y. Westervelt, 1 Lexington Ave., New York, N. Y.

Jan 6, 1919

By M. R. Geer

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state's coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that - it is providing under mechanization in the rest of the country today.

Jan 1, 1949

By C. O. Lee, R. H. Feierabend, Z. W. Bartlett

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By J. P. BONARDI, William F. Boericke

BOULDER COUNTY, Colorado, ranked during the war years and until the end of 1918 as one of the foremost tungsten-producing districts of the world. In 1919 production fell off drastically, due to heavy importations of foreign ores from China, Burma and South America. So large were the imports that even after the enactment of a protective tariff in 1922 of 45c. per lb. on tungsten metal, equivalent to $7.14 per unit (201b.) of tungstic acid? (WO,), the stocks of metal in this country were extensive enough to supply the demands of industry, and prevent general resumption of mining by domestic producers. Even today there are only two producers in the Boulder district though at one time as many as twenty separate companies were in operation. About the same ratio holds for other tungsten-producing districts in the country, including California and Nevada. Total consumption of tungsten concentrate in terms of 60 per cent WO2 in the United States amounted to approximately 3790 tons in 1928, according to Frank L. Hess.' Of this amount, domestic mines contributed 1290 tons, and the rest, 2500 tons, was imported. Yet in 1917, with tungsten concentrate selling at $20 per unit, the Boulder district alone produced 2707 tons, indicating the effect of enhanced ore price upon production. It is believed by American tungsten miners that, given a sufficiently high tariff, all the demands of industry can be met by domestic production without placing a prohibitive burden on consumers. For instance, in steel manufacturing the percentage of tungsten entering into the manufacture is so small that, ?regardless of cost, it can constitute but a small fraction of the cost of steel to the buyer.

Jan 1, 1929

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965