Search Documents

Organization Place - Date 1918 American Iron and Steel Institute New York, N. Y. May American Water Works Association :.. St. Paul, Minn. May 20-25 American Institute of Chemical Engineers Berlin, N. H.. June 19-22 American Concrete Institute Atlantic City, N. J. June 24-26 American Society for Testing Materials Atlantic City, N. J. June 25-28 New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. 9-13 National Exposition of Chemical Industries New York, N.Y.. Sept.23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic' City, N. J. Sept.

Jan 5, 1918

By Craig R. Barrett, Oleg D. Sherby

The creep characteristics of four pure metals with widely Varying stacking-fault energies (silver, copper, nickel, and aluminum) were evaluated above 0.5Tm. Creep tests were performed under conditions of constant atomic diffusivity and constant stress over the elaslic modulus. The sleady-state creep rate, Es, was found to he a funclion of the THE most common empirical representation of the steady-state creep rate, Es, at high temperatures and intermediate stresses is of the form where a is the applied stress, E is an elastic constant, A and n are constants (n is typically stacking-fault energ, y, such that Es is proportional to y3,5. In addition, it was uncovered that the primary creep strain and the strain to fracture increased with increasing y, and that the ratio of initial to steady-state creep rate decreased with increasing y. about 5), Q is the activation energy for creep (usually equal to that for self-diffusion), and kT has its usual meaning. sherbyl and McLean and ale' have used this expression to correlate creep data for a number of pure metals. An interesting aspect of Eq. [I] is the absence of any dependence on the stacking-fault energy. While most creep data seem to obey the stress and temperature dependence predicted by Eq. [I], when data for several metals are put on a master plot they do not fall on a common line but form a band. The width of this band corresponds to a variation in Es of 102 to l03. sherbyl attempted to explain this band by assuming that a grain-size effect was present which led to the observed variation. On the other hand, Felt-

Jan 1, 1965

By Arne Bergholm

Australian rutile was chlorinated in the presence of CO or carbon. The chlorination velocity in CO was found to be strongly influenced by temperature and proportional to the CO concentration, but independent of the Cl, concentration. In the presence of carbon, the reaction velocity is much higher. The reactivity of the carbon and the distance between the carbon and the rutile surfaces are important variables. The reaction velocity is approximately proportional to the Cl, concentration and independent of the CO concentration of the surrounding atmosphere. Experiments with fluidized-bed chlorination of carbon-rutile mixtures indicate that the motion of the bed has little influence on the reaction velocity. At low temperatures, the chlorination velocity of dense tablets is much greater than that of TiO, coke mixtures suitable for fluidization. The reaction mechanism is discussed. In the industrial production of TiCl, rutile is chlorinated in the presence of carbon. Disregarding intermediate steps, the reaction may be expressed by the following equations: The ultimate object of this study was to find out whether the reaction velocity was higher in fluidized bed operation compared with chlorination of pelle-tized carbon-rutile mixtures. From a literature survey and preliminary experiments it was learned that some basic knowledge about the reaction mechanism was needed for a good experimental design. Therefore the following sets of experiments were carried out: 1) Studies on the reaction velocity in the chlorination of rutile with CO as the only reducing agent. 2) Chlorination of separate rutile-carbon tablets. 3) Chlorination of rutile-carbon tablets at different temperatures with various kinds of carbon, various grain sizes, and various tablet-making techniques. This series of experiments was carried out not only with pure chlorine but also with mixtures of chlorine with argon, CO and CO,. 4) Chlorination of rutile-carbon tablets made in a strictly standardized manner. 5) Chlorination of static-bed rutile-carbon mixtures. 6) Fluidized-bed chlorination of the same mixture. The experiments 4 to 6 formed the final and direct test of the main question: Static bed vs fluidized bedo. Although there are many patents and papers dealing with the general aspects of chlorination, only few experiments from which detailed information can be obtained have been reported in the literature. Pamfilov and coworkersl3 have studied chlorination of TiO, with CO or carbon as the reducing agent. They found that the weight decrease per hour at 600o to 800°C amounted to 11 to 14 pct with CO and 45 to 51 pct with carbon. They suggest that phosgene might be an intermediate in the chlorination of TiO,. Takimoto and Hattori have chlorinated reduced titanium oxide (TiO) and found a very high rate of TiC1, -production. They proved that the composition of the gas from the chlorination of rutile-carbon mixtures contained mainly CO. They reported for instance 74.7 pct CO, and 5.6 pct CO at 800°C at which temperature the Boudouard equilibrium composition is 12 pct CO and 88 pct CO. Seligman and Segerchano6 have studied the chlorination of TiO. They proved that Ti0 and chlorine react rather rapidly at temperatures as low as 300°C. Above 400°C, the reaction was complete. At 500°C the velocity of this reaction was much higher than was chlorination of TiO, + C. McTaggart,7 Nishimura, et al. and Wilskam have chlorinated mixtures of carbon and various kinds of rutile or beneficated ilmenite. Nishimura, et al. also report the results from reduction of TiO, with H2, CO, or carbon. At 900°C only 1 pct Ti O is formed in 2 hrs. At 1100°C 23.1 pct Ti, 0, was formed if elementary carbon was present. No carbide formation occurred below 1400°C. McIntosh and Cofferll have observed that the CO, content of the exit gases from chlorination of rutile and calcined petroleum coke is appreciably higher than found in the Boudouard equilibrium. At 900°C the ratio (CO, /CO + CO) is about 80 pct, whereas the equilibrium value is about 2 pct. W. E. Dunn12 has studied the chlorination rates of several TiO,-bearing minerals with CO + Cl, or COCl . Chlorinations were carried out either in a fluidized reactor or a fixed-bed reactor, both having a 30-mm diameter. The results obtained in both reactors were comparable. It was proved that benefi-ciated ilmenite (i.e., ilmenite from which the iron oxide had been removed by chlorination) was chlorinated 10 times faster thanrutile. Sore1 slag showed an intermediate rate. When phosgene is used, the

Jan 1, 1962

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Septa 10, 1917, to Oct. 10, 1917. ALDER, ALFRED 1020 Kansas City St., Rapid City, So. Dakota. AUBEL, VERNE WALLACE, Night Supt. of Works, Broken Hill Proprietary Co., Ltd., Newcastle, N. S. W., Aust. BAKER, ROBERT EARL Works Mgr., Keokuk Electro-Metals Co., Keokuk, Iowa. BALLAMY, JOHN H., Min. Engr., Delaware, Lackawanna & Western Railroad Co,Scranton, Pa. BRADLEY, ALLEN PALMER, Met., American Smelting & Refining Co., Murray, Utah. BRIGGS, WALTER M Pres. Regal Mines Co. Dedham, Mass. BRONSON, EDMOND B., Pres., Bagdad Copper Co., 120 Broadway, New York, N. Y. BROOK, NILES WINFIELD, District. Mgr., Cleveland Min. Co., 625 Bank & Insurance Bldg., Dubuque, BUSKETT, EVANS 1V., Assayer, Custom Assay Office, 620 Joplin St., Joplin, Mo. CAMPBELL, JOHN HATES, Chem. Engr., Robert W. Hunt. & Co., 2200 Insurance Exchange, Chicago, Ill.

Jan 11, 1917

By Henry Newton

It may seem somewhat a work of supererogation to present to the American Institute of Mining Engineers, composed largely of gentlemen with whom the subject is so familiar, a paper on iron ores and their distribution. To many of them, however, it possibly will not be without interest, as there may be some, like myself, who hare nowhere found a connected account of the character of the deposits and the circumstances upon which are founded the great iron-producing centres of the world. This blank I have endeavored to fill,

By Henry Newton

IT may seem somewhat a work of supererogation to present to the American Institute of Mining Engineers, composed largely of gentle- men with whom the subject is so familiar, a paper on iron ores and their distribution. To many of them, however, it possibly will not be without interest, as there may be some, like myself, who hare nowhere found a connected account of the character of the deposits and the circumstances upon which are founded the great iron-producing centres of the world. This blank I have endeavored to fill,

Jan 1, 1875

PENNSYLVANIA ANTHRACITE SECTION Executive Committee R. V. NORRIS, Chairman. CHARLES F. HUBER, Vice-Chairman, W. J. RICHARDS, Vice-Chairman, EDWIN LUDLOW, Vice-Chairman, ARTHUR H. STORRS, Vice-Chairman. CHARLES ENZIAN, Secretary-Treasurer, U. S. Bureau of Mines, Wilkes-Barre, Pa. DOUGLAS BUNTING, FRANK A. HILL, ALBERT B. JESSUP, RUFUS J. FOSTER, JOHN M. HUMPHREY, ROBERT A. QUIN. The Pennsylvania Anthracite Section held its second regular meeting at the Pottsville Club House, Pottsville, Pa., July 25,1914. The meeting was attended by more than 90 members and guests. Vice-Chairman W. J. Richards presided. Following an informal dinner, W. G. Whildin, Mining Superintendent, Lehigh Coal & Navigation Co., Lansford, Pa., presented a. paper on Steep Pitch Mining of Thick Coal Seams, illustrated by numerous drawings. This paper will be printed in the November number of the Bulletin. A lively discussion followed the reading of the paper.

Jan 10, 1914

Engineering Experiment Station, Kansas State College, Manhattan, Kansas. For publications or a list of publications, address the above Of the 29 Bulletins issued by the Engineering Experiment Station, a few on cement and road-building materials may well be listed here: Bulletin 12, Road materials of Kansas; 15, Tests of Kansas road materials, 17, Some strength characteristics of portland cement; 25, Volume change of concrete, 26, A study of fourteen brands of standard portland cement and four early-strength concretes, 28, The durability of concrete, 29, The effect of aggregate and other variables on the elastic properties of concrete

Jan 1, 1933

Executive DONALD B. GILLIES, Chairman WILLIAM WRAITH, Vice-Chairman ERLE V. DAVELER PAUL D. MERICA W. H. PEIRCE Finance H. G. MOULTON, Chairman H. T. HAMILTON HENRY KRUMB Admissions CHESTER A. FULTON, Chairman GEORGE D. BARRON, Vice-Chairman A. B. JESSUP PHILIP KRAFT EDWARD MEAGHER Alternates P.B. BUCKY SAMUEL HASKELL F. T. SISCO

Jan 1, 1939

A. W. AMBROSE, Washington, D. C.-Did you make any analysis of the amount of emulsion at the well and after you flowed it through a lead line to the storage tank? E. A. TRAGER.-B. S. can be formed in passing through a lead line by the friction due to the roughness of the pipe and the irregularities at the joints. R. W. MOORE.-Did you find the percentage of water to be limited to the percentage of oil in the emulsion which formed? E. A. TRAGER.- Yes, the percentage is about 67 percent. water and 23, per cent. oil. R. W. MOORE.-If you added more water would the emulsion be permanent? E. A. TRAGER.-Yes, it would be permanent, but the excess water would separate out. THE CHAIRMAN. (C. W. WASHBURNE, New York, N. Y.).-Did you use hot or cold water in these experiments?

Jan 12, 1919

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Oct. to Nov. 10, 1915: Lester S. Thompson, New York, N. Y. Arthur L. Sweetser, Boston, Mass. William Reed, El Oro, Mexico. Dorsey A. Lyon, Salt Lake City, Utah Heinrich Ries, Ithaca, N. Y. D. W. Blaylock has resigned his position with the St. Joseph Lead Co., Bonne Terre, Mo., and has accepted the position of division engineer for the Big Creek Coal Co., of Chicago, at Harrisburg, Ill. R. B. Lamb announces the removal of his office to Room 1809, 43 Exchange Place, New York, N. Y. C. C. Sanders has taken a bond and lease on the Red Mountain group of 34 mining claims (copper), Patagonia, Ariz., and has commenced extensive development.

Jan 12, 1915

By E. J. Fasiska, H. Wagenblast

The dilalion of a ivon by interslilial carbon was measured by two independent techniques —dilatometric mesurements at 719 c and X-ray measurments of the urlil cell parameters a1 room temperature after quenching. The relative expansion per increase in cavbon content by both methods is (2.9 + 0.3) x 10-3 pev at. pcl C nrzd is temperature- independent within experimental error. This corresponds to (6.3 5 0.6) cu cm per g-atom for the partial gram-atomic volume of carbon in a iron-only slightly smaller than the atomic volume for iron in the same temperature vange. THE only previous quantitative study of the dilational effect of carbon dissolved in a iron was performed in 1934 by Burns1 which, at the time, generated some discussion of possible sources of experimental error.2 For a system of such widespread importance, we felt that a new investigation was merited. Both X-ray diffraction and dilation measurements were used to determine the expansion of the a iron lattice by dissolved carbon, avoiding as much as possible any previous experimental problems and deficiencies. The dilation method at solution temperature offers not only measurements which are free of residual strain but also, in conjunction with the room-temperature X-ray measurements, a method to detect any large temperature dependence of the partial gram-atomic volume of carbon. To insure that quenching strains did not affect the room-temperature X-ray measurements, wire specimens of constant carbon content but different diameter were examined for such an effect. SPECIMEN PREPARATION The material used for both experimental techniques was "Ferrovac E" iron received in the form of 19-mm-diam rod and stated as having the following impurity contents: C, Cr, Cu, Mn, P, and V, each in the range of 10 to 50 ppm; Co, O, Mo, S, and Si, 60 to 100 ppm; W, 200 ppm; Ni, 230 ppm; N, 4 ppm. The stock material was cold-swaged to 0.71 mm diam for the Debye-Scherrer X-ray camera specimens and portions were cold-rolled from 6.3 mm diam to 0.79- and 0.25-mm sheet for X-ray diffractometer and dilation measurements. The wires were annealed in wet hydrogen for 6 hr at 840°C and 15 hr at 720°C, and then quenched into 0°C water. A chemical analysis for carbon after this treatment gave 0.0046 + 0.0014 at. pct C. Three portions of these wires were subsequently held at 719°C in three different hydrogen + methane mixtures and then quenched, resulting in carbon concentrations of 0.0283, 0.0598, and 0.1067 at. pct C by chemical analysis. After carburizing, the wires were swaged to 0.48 mm and electroplated with silver to prevent carbon loss during subsequent heat treatment. The final heat treatment consisted of holding the wires at 72 1°C for 5 min in a He-2 pct H mixture followed by quenching into 0°C brine. The wires were held at room temperature for a few minutes to remove the silver plating using a phosphoric acid-hydrogen peroxide solution, and then stored in liquid nitrogen until the measurements were made. EXPERIMENTAL TECHNIQUE A) Dilation Measurement. The dilatometer consisted of a gas-atmosphere vertical tube furnace modified so that length changes of a ribbon-shaped specimen could be measured externally. This was done by installing a gas-tight mercury seal at the top of the furnace as shown schematically in Fig. 1. The specimen (21.0 cm long, 1.27 cm wide, and 0.25 mm thick) was suspended in the center of the furnace by 3-mm-diam quartz rods with the upper one passing through the cap of the mercury seal. Above the cap, the upper quartz rod was coupled to a lever exerting a load of about 25 g (-12 lb per sq in.) on the specimen and having a 10 times mechanical magnification. The vertical position of a marker at the other end of the beam was read with a traveling microscope with a precision of 0.01 mm. The temperature gradient of the furnace was meas-

Jan 1, 1968

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe’s Minerals Corp.’s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5m3 (300 cu ft) lead and zinc

Jan 1, 1980

By E. J. Ripling, S. I. Liu

IT has been shown in a number of recent publications that much information on the mechanical behavior of metals can be gleaned by first deforming test specimens under one set of conditions, and then evaluating the effect of this deformation by means of a subsequent tensile test. A straining procedure of this type has been applied to study the flow behaviors of a number of metals.1, 2 In these studies the prestraining and testing were both tensile strains, while the straining temperature was varied between the prestraining and testing steps. These data indicate that there is a more or less general flow behavior exhibited by all metals which are pre-stretched at one temperature and then tested in tension at a second temperature. Prestraining a metal at a high temperature produces a lower yield strength during the subsequent low temperature strain than would the same total strain at the lower temperature. On reversing the order of the strains, low temperature prestraining produces a higher yield strength during the subsequent high temperature straining than would a single high temperature strain of the same magnitude. Unlike the flow behaviors, the fracturing characteristics of metals when prestrained under one set of conditions and tested under a second set of conditions is quite material dependent. The fracture behavior of a number of steels2" as well as of a commercially pure zinc,4 have been investigated by these two-step tests and was found to depend upon the position of the transition temperature with respect to the prestraining and testing conditions. Since these fracturing phenomena are complicated by the appearance of the transition temperature, it has been difficult to reliably define the basic effect of a two-step straining procedure in fracturing. Metals crystallizing in the face-centered cubic system do not exhibit transition temperature effects so that the mechanical characteristics obtained on these materials could serve as a base for two-step straining behaviors. Consequently groups of specimens of the aluminum alloy 24s-T4 were prestrained various amounts at room temperature in either tension or compression after which these strained specimens were further strained to failure, or tested in tension, at either room or some lower temperature. Other groups of 24S-T4 specimens were prestretched at various low temperatures after which these were tested in tension at room temperature. These straining techniques then made it possible to compare the behaviors of aluminum with the behaviors previously presented for steels. Material and Procedure The commercial aluminum alloy 24S-T4 in the form of 3/4 in. rods was used in this investigation. The material was subjected to the following treatments before machining: 1—resolution treating at 920" & 10°F for 45 min, 2—quenching in water at room temperature, and 3—aging at room temperature for four days. The re-heat treated material was then machined to either of the specimen shapes shown in Fig. 1. Fig. la shows the threaded-end specimen used for prestraining in compression. Fig. 1b shows the specimen used for both prestrain in tension and final testing. The material subjected to precompression in the form of the specimen shown in Fig. la was re-machined to the specimen shape in Fig. 1b for final testing. Prestraining in tension and final testing were done without any intermediate machining. All straining was performed on a 10,000 1b Riehle tensile testing machine. Tensile strains were conducted in a specially designed concentric fixture which produced an eccentricity of less than 0.001 in." The change in diameter at the minimum section of

Jan 1, 1954

By John A. Emery

The Pea Ridge iron ore deposit near Sullivan, Missouri, is a dike-like mass of magnetite enclosed in Precambrian porphyries. The ore body tops at the Precambrian surface at a depth of 1300 feet below the present surface and extends to an unknown depth. It dips nearly vertically, intersecting the dip and strike of the enclosing porphyries at an extremely sharp angle. Faulting, both pre- and post-ore, appears to be of minor consequence, and present knowledge indicates that no preferred structural conditions existed prior to emplacement. The ore body is composed of magnetite with specular hematite, quartz, apatite, and pyrite occurring as accessory primary minerals. Specular hematite in appreciable quantities occurs on parts of the cap and the footwall of the ore body. Fresh porphyry breccia is enclosed in the magnetite along the hanging wall and in the western portion of the ore body. Hanging-wall quartz-amphibole and footwall quartz-hematite occur as replacements of certain porphyries. Further alteration has caused sericitization of parts of these zones. The ore deposit is interpreted as having been formed essentially by a single injection of a magmatic differentiate with hydrothermal end phases forming the quartz-amphibole and quartz-hematite portions of the deposit.

Jan 1, 1968

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.' This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

By David R. Poirier

THE activity of carbon in Fe-C-Cr liquid solutions has been measured by Richardson and Dennis,1 Fuwa and chipman,2 and Goto et aL3 Fuwa and Chipman2 have presented their data along with data of Richardson and Dennis1 and utilized an interaction parameter. However, the interaction parameter is only valid for dilute solutions of carbon, because, as indicated, the same interaction parameter does not apply to more concentrated solutions of carbon (i.e., the effect of chromium on the saturation of graphite in liquid iron). Ohtani4 has attempted to account for the effect of carbon concentration on the interaction parameter; however even his analysis does not apply to the saturation data. Also, the effect of temperature on interaction parameters must be taken into account. Therefore, in any process where the concentration of carbon and/or the temperature changes (such as solidification), the use of an interaction parameter is not adequate to know the activity of carbon. The purpose of this communication is to make use of the existing data on the effect of chromium on the activity of carbon in liquid iron solutions in such a way that the activity can be described as a function of both composition and temperature. The method is an extension of Rist and chipman's5 analysis for the binary Fe-C solutions. As in Rist and Chipman's analysis, the activity coefficient is assumed to obey the relation: log y1 = at(l -X1)2 + It [1]

Jan 1, 1969