Search Documents

By E. C. Carris

THE loading of bituminous coal mechan¬ically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous pro¬duction in the United States was loaded by mechanical means. During the past i6 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all¬time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase in mechanical cleaning. The importance of mechanical cleaning of coal was recognized many years before the mechanical loader was introduced, because of the impossibility of cleaning manually the sizes below 2 in., and the increasing competition from other fuels. Utilization of mechanical loaders without mechanical cleaning on the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely intro¬duced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problems have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expendi¬tures; the solution taking the pattern of rearranging and improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. LARGE IMPURITIES The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1946

By J. R. Long, T. R. Graham, R. S. Dean

FOLLOWING the development of elec¬trolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to com¬positions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study1 established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, 10 pct manganese, 25 pct zinc alloys' a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-working and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

I. PRESIDING OFFICER, At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President, 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6, Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute, He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute, The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account in ledger form of all such back numbers, He shall on the first day of January of each year submit to the Library Committee a statement of the number of copies of Transactions, magazines and other publications printed during the preceding year, giving the number distributed and remaining undistributed; also a statement covering additions to and withdrawals from the total stock of Institute publications, with the number 'remaining on hand at date of statement,

Jan 1, 1928

By Gunnar Thaning, Borje Bjorkvall

At LKAB Central Division for Metallurgical Research at Malmberget, Sweden, fired pellets are examined in respect to mechanical and reduction properties. The paper deals with descriptions of the test methods. It also involves the rationale for the choice of these tests. Their correlation to the blast furnace operation will be examined. The mechanical tests used are the ISO-tumbler test and the cold compression strength test. Concerning the metallurgical properties, experiments have shown that some superbasic pellets in particular have different disintegration properties in different temperature ranges. Pellets which have favorable reduction properties when tested under isothermal reduction at high temperature may disintegrate to a large extent under low temperature reduction. This is also valid for some types of acid pellets. Consequently, it was found to be necessary to determine the reduction strength both at high and low temperatures. In the low temperature range, the disintegration is measured by tumbling the pellets in soft reducing conditions at 600°C in a modified Linder test equipment. The high temperature reduction strength is determined under load in the Burghardt-Grebe equipment. However, in order to get more information of the high temperature strength, LKAB intends to introduce a softening test. The tendency of high temperature disintegration will also turn up in the swelling test. The swelling properties are examined according to a procedure developed at LKAB. In this test the pellets are subjected to free swelling without mutual contact. The reducibility of the pellets is recorded in the swelling test.

Jan 1, 1974

By Morris Muskat

The detailed analogy between flow systems in porous media and the corresponding poten-tiometric model systems is developed under conditions where it may be desirable to take into account variable pay thickness, variable porosity, and permeability, and also the dependence of the fluid density on pressure. It is shown that in such models it is only necessary that the electrolyte thickness be made everywhere proportional to the millidarcy-feet of the formation. In contrast to the iso-vol type model, previously suggested as a basis for the analogy, the porosity does not enter directly in the construction of the model. It is introduced only in translating the electrical voltage gradient measurements into the equivalent fluid travel times. A discussion of this procedure is given. I NTRODUCTION It is now some 50 years since it was pointed out' that on the basis of Darcy's law Laplace's equation must govern the steady state flow of homogeneous fluids through porous media. It is 16 years since the obvious implication of this fact, namely, that such steady state homogeneous flow systems in porous media could be simulated by electrical analogies, was first applied2 to problems of practical interest with respect to oil production. In these initial studies major emphasis was placed on the use of electrolytic models, made of blotting paper, to give a direct and graphic history of the fluid particle motion in regular and infinite well networks. However, it was also noted there that the basic requirement of the model was that it give a potential distribution similar to the pressure distribution in the flow system, and that from the electrical measurement of the potential distribution the fluid particle motion could be graphically or numerically determined. This was demonstrated by application to the five-spot infinite network, for which a conducting metallic sheet was used to establish the equipotential contours. As anticipated, the fluid particle motion computed from these contours agreed well with that given directly by the blotting paper model. For irregular well distributions it was found more convenient to use electrolytic bath analogs rather than metallic sheets. Several investigations,3'4 as applied specifically to cycling well patterns, have been reported with these models, which have become known as "potentiometric models." However, the extremely laborious nature of both the electrical measurements by direct probing and the associated interprctive computations retarded the widespread use of these procedures. The electrical measurements can be accelerated by using a four-probe electrodc,5,6 which provides a means for simultaneously determining the streamline paths along which the fluid particles must move and the voltage gradients along these paths which are proportional to the fluid velocitics. With the increasing frequency of discovery of condensate pools, as drilling depths are becoming greater, the applicability of the potentiometric model to production problems, and especially to the study of well patterns for cycling, has been given a fresh impetus. Although the formal theory for determining the motion of fluid particles in porous

Jan 1, 1949

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.' Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph' (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,' have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

By Howard Eavenson

PRIOR to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and was usually used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia-which was then regarded as the standard coking and gas coal of the coun, try, and the best coal available anywhere for these purposes. With the advent of the by-product oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for cokemaking, gas and other metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than the best of the coal from the Pittsburgh seam, or than any northern coal, and in by-product ovens produce coke that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these seams is shipped in great quantities without beneficiation and is lower in ash and sulfur than the best washed product from any seam mined in the north.

Jan 1, 1932

By A. B. Dyes

In the operation of a water-driven reservoir, a free gas saturation can he established by maintaining production rates fast enough to cause the reservoir pressure to decline below the bubble point. The benefit of such a procedure on the displacement efficiency of the oil by water is illustrated for two types of sandstone samples from one reservoir. Those rock samples showing the poorest recovery to water drive in the absence of a free gas saturation give the most improvement in the presence of a free gas saturation. Employing one type of reservoir fluid (low .shrinkage) the benefit of evolved gas on oil displacement is calculated at several reservoir pressures below the bubble point. This demonstrates the presence of air optimum pressure for water displace,rnent which is .several hundred pounds per .square inch below the bubble point. Displacement of oil at the optimum pressures results in the removal of 7 to I? per cent more oil than would be obtained by displacement at the bubble point pressure. In some instance. this magnitude of increase may be worthy of consideration in establishing the maximum efficient rate of production from many water-driven fields. INTRODUCTION For many years the belief that the use of gas could be combined with that of water to result in a better recovery operation than the use of either of these phases alone has been prevalent in the oil industry. This is evidenced by the several field trials which have employed the injection of gas and water in combination.1.2.v In most cases the small amount of any additional recovery, in combination with the limited knowledge available on the older reservoirs, has left uncertain the influence of gas on recovery in these earlier attempts to combine the use of gas with water. Research studies in recent years have demonstrated through laboratory. floods the magnitude of the benefit of the presence of gas on the displacement of oil from sandstones by water.5,6,7,8,9,10,11 In addition, studies of the distributions of the phases which are present during the displacement process have developed concepts concerning the mechanism by which this benefit is obtained."." It now remains for the engineer to incorporate these findings into the general technology of reservoir operations. It is the purpose of this paper to illustrate that the production of a water-driven reservoir at pressures below the bubble point is one such operation whereby improved oil displacement efficiency can be obtained as a result of gas evolution. The establishment of a gas saturation by evolution of dissolved gas was one of the techniques used by several investigators in the laboratory studies. The possibility of obtaining the benefit of gas evolution in water-driven reservoirs by producing at pressures less than the bubble point has 3150 been pointed out previously." The desirability of this operation has undoubtedly

Jan 1, 1955

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By Martin S. Maier, H. R. Nelson

THE diffusion of metals plays an important role in many metallurgical processes, 1,2 as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystallization and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved.1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms-self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radio-activity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes-lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-10 and bismuth10 using natural radioactive isotopes, and of gold11 and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited on one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc, 14-16 silver,17 and copper.18 The second method was used for the work described in this paper. MATERIALS The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by 1/8 in. thick. Samples of high-purity copper described by Phillips and Skinner19 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By William J. Douglas, Jack T. Urie, Randall D. Metz

Production and financial planning for a new underground mine requires the coordination of equipment and coal reserves in a manner which assures that resources are utilized efficiently in achieving the target mine production. It is necessary to establish the productions which are attainable at the section level during different mining operations (advance, retreat, development) and under different mining conditions (roof, seam height, resource quality). It is also necessary to identify the interactions between production plans and ventilation equipment So that operations can be carried out without disruptions caused by inadequate ventilation. A set of computer models has been applied in planning a number of new coal, oil shale, and phosphate mines. A critical path production model, CPMINE, was used to determine face production levels for different cut sequences and seam heights, taking into account machine performance characteristics and operational availabilities under these varying conditions. The results formed a production data base for use in the mine sequencing model, MPLAN. This model processes each of the segments of a user-defined mine sequence network (strategy tree) taking into account the equipment available for mining operations and the previously determined production scheme devised by the mining engineer. Mine ventilation was analyzed with an expanded version of the Penn State MVS Ventilation model to determine fan and ventilation shaft requirements for supporting alternative production strategies. The MCOM mine cost analysis model has been applied to evaluate the economic performance of mining alternatives. The results of these studies were used to make decisions relating to equipment selection and acquisition schedules for both room-and-pillar and longwall mining systems. The approach and procedures which were used during these studies are described.

Jan 1, 1983

By Nicholas J. Grant, John Chipman

A FULL understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization; the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag-i.e., equilibrium conditions-and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck :20 [ ] Among others there appear the following:

Jan 1, 1946

By Gilbert H. Cady

Extensive sampling of coal in Illinois during the past 10 or 12 yegrs by the State Geological Survey, in cooperation with various organizations, such as the U. S. Bureau of Mines, the University of Illinois, and the Illinois Cooperative Mining Investigations, has made possible the delineation of two areas of low-sulfur coal in the southern part of Illinois. The $fur content is less than 1.25 per cent., so that, if otherwise suitable, these coals can be employed for metallurgical uses and for the manufacture of water-gas and retort gas. One of these areas is small and lies in Jackson County, near Murphysboro, the other is much larger and includes a large part of the famous Franklin County field. A small area of No. 2, or Murphysboro, coal has been worked for many years near the town of Murphysboro, Jackson County, Ill. In two mines, at least, the coal has a sulfur content of less than 1.25 per cent. It is doubtful, however, whether this field will ever be a source of large tonnage as the total area underlain by low-sulfur coal in workable thickness is probably less than 15 sq. mi. (24.14 sq. km.), and a large part of it has already been worked out.. The location of the area of low-sulfur coal in the Franklin County field is shown in the accompanying map. The small area underlain by the Murphysboro low-sulfur coal is shown near the town of that name in the central part of Jackson County. The larger area lies in the west side of Franklin County, extending also about 6 mi. (9.65 km.) south into Williamson County, about 4 mi. (6.43 km.) west into northern Jackson and western Perry County, and northward an undetermined distance into Jefferson County. All but the northern limit of the area is fairly well defined by sampling in numerous mines. The inner cross-lined area is underlain by coal having less than 1 per cent. sulfur, the outer boundary surrounding the area underlain by coal having less than 1.25 per cent. sulfur. The coal mined in the district is No. 6 or Herrin coal, commonly known as the Carterville or Franklin County coal. The bed has a thickness varying from about 8 ft. (2.4 m.) on the border of the low-sulfur area up to more than 10 ft. (3 m.) in the central portion, locally having a thick-

Jan 1, 1920

The finding of gold, in enriching quantity, along the streams that issued from the western foothills of the Sierra Nevada was the prelude not only to the birth of an organized mining industry in California but to the intensive exploration of the entire Pacific slope; it presaged the feverish exploitation of the mineral resources that the ubiquitous prospector soon uncovered all over our western domain. At first when this migration began, as typified by the rush of 1849, there was no time to examine the signs of ore that were to be detected along the track of adventure, and, it must be added, not many in that motley crowd of gold-seekers were qualified to interpret the signs if they had lingered to look at them. Such intelligent curiosity as a few of them possessed was directed to the finding of gold chiefly, if not exclusively; and their good sense in this respect can not be impugned, because in a new and remote country the less valuable metals and minerals are unlikely to be worth the winning. Many of those that came to California crossed the alkaline wastes and sagebrush prairies that extend between the Great Sal? Lake and the ramparts of the snow-clad Sierra; when coming overland they found it convenient to halt on the eastern slope and to pitch their camp in the valley of the Car- son river before they began the tedious ascent of the mountains and the final entry into the land of gold. One of the trails most used by these immigrants followed the Carson river to the mountain meadows south of Lake Tahoe and then descended among the pine-woods of Placerville, where they went to work with pan and shovel in the gold-bearing streams

Jan 1, 1932

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.'s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936