Search Documents

By Joseph Kaye Wood

A metal is said to be overstrained when it is deformed beyond the elastic limit at a temperature well below the critical range, as in cold working. Quantitatively, overstrain might be considered as that part of the total elastic deformation of the piece of metal, left over after the external load is removed, that added to the permanent deformation due to plastic action will give the total permanent deformation. Ordinarily the effects of this phenomenon, which vary with the internal residual stress probably in accordance with Hooke's law, are more noticeable when the yield point of the metal is exceeded, but they probably also exist to a smaller degree when the load is just large enough to cause the least amount of permanent set. These effects, which we recognize as the result of overstrain, are as follows: 1. An apparent increase of the elastic limit in tension and a decrease of the elastic limit in compression, provided the external load is tensile. The reverse is true when the load is compressive. 2. An elastic after-effeet in which time and temperature are important factors. 3. A state of imperfect elasticity in which Hooke's straight line becomes slightly curved, giving rise to an hysteresis loop. 4. In addition to the apparent increase in the elastic limit, such properties as the hardness, ultimate strength, and resistance to fatigue failure are increased, provided the overstraining has not been carried far enough to make the metal brittle. 5. Correspondingly the ultimate elongation, reduction in area, magnetic quality, ratio of endurance limit (fatigue breaking stress) to elastic limit, and resistance to season cracking (in certain copper alloys) are decreased. The question naturally arises: how do these changes in the properties of a metal resulting from overstrain influence our method of design? The fact that most of the desirable qualities are increased makes overstraining a favorable process, from an engineering standpoint; but on the other hand, the loss of such qualities as perfect elasticity and complete

Jan 1, 1924

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By Ray W. Arms

DRY cleaning, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc. Air Stratification In all of the above groups of air separating devices, the same phenomena are found as exist in water concentrators; that is, free settling will be found in some and hindered settling in others, with a complex action on the reciprocating tables similar to the wet tables. The experimental value of the settling ratios of particles in air has never been determined but, following the formulas given in Richards'

Jan 1, 1924

By L. H. Schwartz, M. V. Nevitt

THE phase Ti2Ni has been described by Laves and Wallbaum,1 who found the phase to be face-centered cubic with 96 atoms per cell, by Duwez and Taylor,2 who confirmed these observations and reported a lattice parameter of 11.333A, and by Rostoker,' who reported the structure to be isomorphous with the double carbide Fe,W,C, type E93, and to have a lattice parameter of 11.29A. In this study a group of isostructural phases has been found among alloys of certain second and third long-period transition elements. The systems investigated included all the combinations of zirconium and hafnium with the Group VIII elements rhodium, palladium, iridium, and platinum. There is evidence that many of these new Ti2Ni-type phases require oxygen for their stability in the temperature ranges in which they were studied. EXPERIMENTAL PROCEDURE Alloy samples weighing 5 g were prepared by arc-melting metals whose purity is indicated in Table I in a helium-argon atmosphere. Samples of the as-cast buttons, wrapped in molybdenum foil and sealed in evacuated quartz tubes, were

Jan 1, 1959

By C. A. Czako

INTRODUCTION In recent decades sintering and pelletizing of finely divided materials have become the primary tonnage producing modes of agglomeration. This statement is especially true in the iron and steel industry and, to a lesser degree, in the nonferrous, chemical and non-metallic minerals processing industries. In every industry the main objectives in agglomerating fines are essentially the same, namely to convert ores, minerals and chemicals of undesirable fineness into agglomerates characterized by a size consistency desirable for subsequent use or processing. Depending on the type of agglomeration process selected and the conditions maintained during agglomeration, the physical process of increasing size is complemented by a number of other unit processes. These processes can occur simultaneously, consecutively or in an overlapping manner. Some of these additional unit processes are incidental to the agglomeration operation, but at the same time can be critical, depending upon the subsequent use of the product. Accordingly, during processing, conditions have to be controlled to either suppress or enhance the extent of completion of these unit processes. The purpose of this report is to review laboratory testing as the basis for engineering modern sintering and pelletizing plants. Considering that most typical applications are for the iron and steel industry, agglomeration of ferrous materials is reviewed and discussed. When these total processes are adapted to suit non- ferrous materials, chemicals, or non-metallic substances, the over- all approach remains the same; only the processing parameters are affected as necessitated by the different nature of the materials.

Jan 1, 1977

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By J. L. Jernegan

IN a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of Western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaft-furnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the various metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

Jan 1, 1876

By K. L. Komarek

Based on theoretical and experimental evidence a discussion follows of the behavior of phosphorus -bearing iron ores in the R-N Direct Reduction Process and suggestions are made of methods of reducing the amount of phosphorus in the metallic end product. In ferrous metallurgy a direct reduction process is one in which iron ores are reduced to metallic iron with gaseous or solid reductants without the appearance of a liquid phase. A number of attractive features have induced several companies and government agencies to invest in the development of direct reduction processes. A summary of all direct reduction processes up to 1954 has been given by Barrett,' and Wiberg,2 and Willems3 have reviewed the most recent developments in this rapidly expanding field. Many difficulties have been encountered in direct reduction processes and the nature of these difficulties has varied from process to process. One problem common to almost all of them is the removal of phosphorus which is one of the reasons for the rather pessimistic outlook given by some government publications4'5 to direct reduction processes. In this paper an attempt is made to give a theoretical explanation of the variations in phosphorus removal observed in the R-NY Direct Reduction Process. However, many conclusions are general enough to be applicable to other processes. Most iron ores treated by the R-N process yield products lower in phosphorus than the original ore. A qualitative account of the factors has been given by Stewart, Reed, and Herasymenkoe but the erratic removal of phosphorus from some ores and the general importance of this problem make a more careful analysis of the theoretical aspects desirable. In the R-N process mixed ore or balled fines, ex-

Jan 1, 1963

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. [ ] A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By L. S. Darken

THE manufacture and treatment of metals comprises operations whose effectiveness depends in large measure upon diffusion phenomena. The significance of such phenomena has, for a few simple cases, long been understood, but in more complex cases it has not been adequately recognized. This paper presents a mathematical analysis of some of the cases in which diffusion leads to the formation of a new phase within the metal, and this analysis provides a basis for interpreting quantitatively many apparently diverse experimental observations recorded in the literature, some of which are outlined in the following pages. OBSERVATIONS RECORDED IN LITERATURE An outstanding instance is the general type of phenomenon in which diffusion of an element into an alloy is followed by a phase change, which most frequently is a reaction (precipitation) of the diffusing element with one or more components of the alloy to form a compound. Thus in certain alloys heated in contact with oxygen not only the usual oxide scale appears but, in addition, beneath the surface, a well-defined zone in which free oxide particles are dispersed with notable uniformity. This zone, commonly referred to as the subscale or zone of internal oxidation, is remarkable in that the visible boundary between it and the unaltered metal is usually sharp. Such a subscale, which appears to have been recognized first in oxidized copper alloys, has been described and studied by C. S. Smith,1 by Rhines,2 and by Rhines, Johnson and Anderson;3 but it appears also in other alloys when they are exposed to conditions that bring about the precipitation of some compound, not necessarily an oxide. Another clear case of this same kind is the diffusion of carbon into a steel containing an element such as molybdenum, chromium, vanadium or tungsten, whose carbide is less soluble in iron than iron carbide, the result being that some part of that element is precipitated as a dispersed carbide. A similar phenomenon may occur on the welding of two alloys each of which contains one of a pair of elements that react to form a compound or a new phase of any sort. But in addition to the precipitation of a compound formed from the diffusing element, other effects may result merely from the presence of the diffusing element. For instance, if homogeneous austenite, nearly saturated with respect to carbon, is heated in contact with silicon in the absence of oxygen, one would expect to find, behind the several iron-silicon phases analogous to a scale, a zone of austenite containing dispersed carbide, because of the fact that silicon decreases the solubility of carbon in iron. As still another example, oxidation of an alloy may result in diffusion toward the surface of one or more of the constituents; for instance, during oxidation of a steel containing an element such as copper, which is less prone to oxidation than iron, there is a notable enrichment of copper just beneath the scale-metal interface. As an example of a yet more

Jan 1, 1942

Jan 1, 1897

By Eugene Guccione

Before answering the question raised in the title, let's briefly consider how East-West trade is viewed within the entire US political spectrum. Essentially, there are four major schools of thought: (1) The Peaceful-Coexistence School. Advocates of this school call themselves free-traders and hold to the premise that: (a) trade benefits all parties involved, hence it is the best tool to achieve peace; (b) US trade barriers should be removed, and the quicker the better; and (c) negotiations, cultural exchanges, and political compromise should be used extensively.

Jan 9, 1974

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

Jan 2, 1966

HOWARD N. EAVENSON, Chairman C. T. HAYDEN, Vice-chairman, Bituminous Coal Production CHARLES DORRANC~ Vice-chairman, Anthracite Coal Production HOWARD P. ZELLW, Vice-chairman, Evaluation of Coal for Coke Making W. H. F'LTLWEILER, Vice- Chairman Gas and Its Manufacture 3. B. MORROW, Vice chairman, Coal Preparation

Jan 1, 1928