Search Documents

By A. M. Gaudin

IN flotation lime is used to depress pyrite. For this purpose it is preferred to caustic soda. The low cost of lime and the widespread availability largely account for this preference. However, there is some evidence1 that pyrite is more readily depressed by calcium than by sodium ions at the same pH. To measure the difference in adsorption of calcium and sodium, which is thought to lie at the basis of the differences in depressing action, radionuclides of

Jan 2, 1953

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By F. C. Stanford

The work of an engineer is to direct natural forces so that the: bring about the results that he wishes to secure. Heretofore he ha concerned himself chiefly with physical forces and inanimate objects until he has secured a truly marvelous degree of control over them The great problem of the present age is to secure a like degree of know1 edge and control of the human factor. Progress has already been made along this line, but it is only a beginning. Wilhelm Ostwald says tha scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to main tain a high average in prophecy. In short, 'the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essentia need of the period is for more brains; if we only had sufficient knowledg and sagacity we could not only solve all difficulties, but prevent then from arising. This generalization holds good for an industrial organization. Th most vital need of the management is for more brains. The logica course for an engineer in charge of an industrial organization is, therefore to direct whatever forces may be at his command toward the development training, and guiding of all the brains in his organization. This is easie said than done, for it involves the carrying on toward two objective: the maximum of productive work, and the development of the individual who perform it. This is essentially like the rebuilding and enlarging of plant, keeping it in full operation the while. On the other hand, if th aim is merely for maximum production from an organization, withou offering opportunity for development, the final outcome will necessari be like that of a plant that is driven at full capacity without stoppin for repairs or improvements; it eventually becomes so run down th either a complete rebuilding is necessary or else it has to be abandone

Jan 1, 1918

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By R. V. Ramani, G. W. Luxbacher

Computer simulation of mine ventilation system is rapidly becoming an essential tool in mine planning and design. This Paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve primarily for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1980

[ ] (17) WORTHINGTON: Cartoonist-author Don Herold recently took a look at the Worthington Corp., putting the results into a compact booklet called "A lot of things beside pumps." The story is aimed to better acquaint you with Worthington and how they came to produce a diversified industrial equipment. (18) SPEED REDUCERS: Now available is Cleveland Worm & Gear Co.'s new general catalog. In its 180 pages are the illustrations and description of the complete Cleveland line, together with full engineering data, dimensions, weights and horsepower capacities of the various drives. (19) METAL PRODUCTS: Armco Drainage and Metal Products, Inc. has just published a condensed 6-page catalog of its products designed for mining use. It describes and illustrates such products as Flex-Beam guardrails, corrugated metal pipe, liner plates, retaining walls, Steelox buildings, and welded pipe. (20) RECORDS: Pre-scheduled, controlled, preventive maintenance reduces costly downtime to a minimum and eliminates the need for large emergency crews. A new folder describes how such a program can be accomplished by using Remington Rand Inc., Kardex visible records. Another Remington Rand Inc. bulletin is the certified case history of how Kardex visible purchasing records help maintain a smooth running purchasing department.

Jan 1, 1952

By Allan B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drill- holes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 ¼ -in. diam, on 25-ft and 100- ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals.

Jan 7, 1959

By O. Lietard, J. Yvon, R. Mercier, J. F. Delon, J. M. Cases

INTRODUCTION Fineness is one of the main characteristics of powders and this parameter is the object of several definitions based on criteria connected with their uses as well as their determination methods. In trying to obtain the best reaction surface, fineness is characterized by the determination of the specific surface, but in other cases, particle size analysis is used. These two main methods are not, in fact, entirely independent and their complementary nature provides information concerning the morphology of the particles. In the case of a product formed by isodimensional spheres, the relationship between the specific surface and the diameter is well known: [S = 6 spd] where p is the specific weight of the material and d the diameter of the spheres. With no monodimensional spheres, but rather a granulometric distribution whose occurrences follow a mathematical law (1), the relationship is more complicated. The relationship between the specific surface measured by gas adsorption and the data of the particle size analysis is much more difficult to predict in the case of asymmetric porous particles, whose particle size distribution curves do not correspond to a known statistical law.

Jan 1, 1980

By A. G. Weber, R. L. Ledbetter, A. L. Hicks

A procedure which makes use of both analog and digital computers has been developed for predicting the pressure-production behavior. of water-drive reservoirs. The electric analyzer is used for matching the past pressure and production history of the reservoir and inferring the physical characteristies of the aquifer. When the history has been matched, a .set of base curves called influence functionce" are derived and the future behavior of the reservoir is calculated from these curves. INTRODUCTION Electric analog methods are particularly well-suited for complex water-drive problems. Like all other methods of analyzing water-drive reservoirs, however, analog methods are subject to certain limitations. One of the more obvious and serious of these results from inaccurate or insufficient knowledge about physical characteristics of the reservoir and aquifer. However, it is not insurmountable because the unknown characteristics can usually be inferred from the reservoir's previous behavior. Simons and Spain have shown that even with scant reservoir data and limited production history, electric analyzer studies can provide useful and reliable results. Aside from this limitation on analyzer predictions, the main disadvantage has been lack of a technique for keeping predictions abreast of latest production forecasts. Pressure behavior of a reservoir depends on the rate at which fluid is withdrawn; it is therefore necessary to specify the future withdrawal schedule before the future pressure behavior can be calculated. Conventionally, the electric analyzer predicts pressure behavior for a specific production schedule. If this schedule is abandoned in favor of some new one, as is frequently the case, either the study must be rerun or results adjusted in some manner. The usual procedure is to predict pressures for several different forecasts covering a wide range of production rates. Pressures for specific rates other than those studied can then be approximated by interpolating between the analyzer predicted curves. However, reliability of this type of prediction is doubtful. This paper describes a technique for predicting future behavior of water-drive reservoirs that retains all advantages of electric analyzer analysis and eliminates the main disadvantage. That is, the analyzer is used conventionally to infer unknown reservoir parameters from the pressure history, but not to predict the future behavior directly. Instead, a derived set of base curves, called influence l'unctions, can be used to calculate future behavior for any production schedule.

By Dr. O’Neil Thomas J., Donald W. Gentry

Pure gold was hidden in the quartz, they said, 'Twas proved by dreams and signs, and rods divining, By chemic tests, and spirits of the dead, In fact by everything-except by mining. " from R.E. White, "The Mining Town," Alta California, August 18,1873 Textbooks in mining engineering have traditionally covered ore reserve estimation and mine valuation in a single volume. Indeed, Examination and Valuation of Mineral Property by R. D. Parks (1957), having been the standard of the profession for over 20 years, is a classic example. However, the state of knowledge in these two fields has grown tremendously. Most mining engineering curricula now cover these topics in separate courses, and in practice, these tasks are usually performed by different individuals. Thus, this trend now suggests the need for separate, specialized publications rather than a single volume for both topics. Because of the separate development of the science of ore reserve estimation, it is important to state at the beginning what this chapter does not cover. It does not address in detail the design of sampling programs, sampling methods, or the processing of samples or sample data compilation. There are a number of suitable references available on these topics, including Peters (1978), Gy (1979), as well as the previously cited book by Parks. Furthermore, this chapter does not cover in any substantial detail either the traditional methods for using sample data to calculate ore reserves or the more recently developed geostatistical methods. The traditional methods are thoroughly covered by Popoff (1966) and more concisely by Barnes (1980). Among the more useful references for statistical applications in ore reserve estimation are Barnes (1980), David (1977), and Clark (1979). A thoughtful review of the entire science and art of ore reserve estimation is provided by King, McMahon, and Bujtor (1982). In spite of the fact that expansion of knowledge now calls for separate books on ore reserve estimation and financial evaluation, neither publication can ignore the important interrelationships between the two fields. In regard to this text, the unique and crucial role of ore reserves can not be omitted entirely; however, the field is now simply too extensive to treat here in any comprehensive manner.

Jan 1, 1984

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. Fugitive dust has been defined by the courts as particulate matter other than that emanating from a specific point such as a stack or chimney. A typical air pollution control agency regulation reads as follows : “Fugitive Dust " "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired or demolished without taking reasonable precautions to prevent particulate matter from be- coming airborne. Such reasonable precautions shall include, where applicable, but not be limited to the following:

Jan 1, 1981

By J. N. Sicking, F. H. Brinkman

A new method for obtaining equilibrium vaporization ratios (K-values) for reservoir fluids has been developed and tested. By application of the method, complex experimental measurements of liquid and vapor phase compositions are eliminated. This simplified technique reduces the cost of experimental equilibrium-ratio data for reservoir studies of condensates and volatile crude-oil systems. The method is designed for systems of constant composition and, therefore, is best suited for depletion studies where compositional changes at high pressures are minor. The basic data required, in addition to the composition of the initial reservoir fluid, are the relative vapor-liquid volumes and densities at reservoir temperature and variom reservoir pressures. Tests demonstrated that the method predicts equilibrium ratios accurately for condensates. A single test on a crude oil was not conclusive; further testing will be necessary before the accuracy of the method can be determined for crude-oil systems. In addition to determining equilibrium ratios, the calculation method provides information on the physical properties of the "plus" component in the vapor and liquid phases. The "plus" component is that mixture of components heavier than the least volatile fraction analyzed. This information is useful in studies of both natural depletion and cycling operations for condensate reservoirs where the heptanes-plus component in the gas phase is produced from the reservoir. INTRODUCTION As more volatile oil and condensate reservoirs are found, the use of phase behavior techniques to predict their performance is increasing in importance. These techniques have long been used for condensate fields and have more recently been applied to crude-oil fields containing oils of medium-to-high volatility. In these phase behavior methods, equilibrium ratios (K-values) are used to predict compositional changes in the reservoir fluids—thereby accounting for the recoverable oil that exists in the gas phase. The reliability of the predictions depends to a large extent on the equilibrium ratios used. These values must be obtained for each component for the entire pressure range being investigated. Unfortunately, because of the complex nature of hydrocarbon mixtures, accurate K-values are hard to obtain. The equilibrium ratios for a particular component will vary not only with the temperature and pressure, but also with over-all composition of the system. The importance of composition is quite critical at elevated pressures, but becomes negligible at pressures below about 300 psia. Therefore, because most phase behavior problems involve the high-pressure region, each fluid system becomes a special case. Experimental programs to determine characteristic K-values are quite difficult and time-consuming. Thus, it is often necessary to resort to approximations of the K-value data. Charts giving K-values for various mixtures and classes of mixtures are available in the literature. However, there are two major difficulties in using them: (1) the K-values of the "plus" component (that mixture of components heavier than the last one analyzed) must be obtained by extrapolation from the K-values of the other components; and (2) the K-values obtained must finally be adjusted by trial and error to agree with observed volumetric data. To eliminate these difficulties, a new method of determining equilibrium ratios was developed. Briefly, after the composition of the system as a whole has been analyzed, the method uses empirical correlations and the gross fluid properties of the system (relative vapor-liquid volumes and densities) to calculate K-values. Because the calculative procedure is long, it is best solved on a digital computer. About one hour of machine time on an IBM 650 computer is required to develop a K-chart for the fluid being examined. DEVELOPMENT OF THE METHOD OF OBTAINING K-VALUES Equilibrium ratios are defined as the ratio of the mole fraction of a component in the vapor phase to its mole fraction in the liquid phase. This statement is expressed in Eq. 1. A typical plot of equilibrium ratios for a particular system is shown in Fig. 1. It should be noted that, at pressures near the saturation pressure, the K-values appear to converge to a common point. This apparent convergence point is called the convergence pressure and is a characteristic of the system involved. Various empirical correlations of K-values have been noted. It has been observed that an isothermal plot of

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960