Search Documents

By L. H. Sjodahl, J. B. Conway

of each particle on grain boundary movement is proportional to the area it occupies on the grain boundary and this increases with the square of the particle radius. In contrast to the impression gained by Tiwari the effectiveness of a particle, as a grain boundary obstacle, increases rapidly as the particle size increases. The counterbalancing factor in a dispersion of constant volume (e.g., those considered by Zener) is of course the rapidly diminishing number of particles, a situation which does not exist in thoria dispersed materials where the volume fraction of thoria remains constant. Although it has been assumed that the Zener approach is valid for the sake of the above argument, it is open to the following objections: 1) It assumes that the effect of many small particles along a grain boundary is cumulative and does not take into account the possibility of each small particle being overcome separately. In this case the boundary will not be able to move forward until the largest particle on the boundary has been overcome. This means that the rate controlling factor will be the rate at which a few relatively large particles are overcome with the remaining small particles playing a negligible role. 2) When the dispersion consists of very small particles the interparticle spacing is usually small compared to the grain size and most particles are located away from grain boundaries where they can play no part. The most efficient dispersion, from a purely geometrical viewpoint, is one where the particle spacing is equal to the grain size so that all the particles are on grain boundaries. Tiwari's second point that voids cannot prevent re-crystallization seems to be unfounded as several workes20-23 have shown that voids alone can retard grain boundary movement and recrystallization. To further convince Tiwari, Fig. 17 shows a void in deformed TD Nichrome holding back a recrystallization interface. Tiwari's explanation for the effect of voids on recrystallization, i.e., they reduce local strain energy and hence lower the driving force for recrystallization may be valid in itself but is irrelevant to the present case where even complete recrystallization after ONE of the more recently proposed expressions for describing stress-strain behavior is that due to Voce.1,2 This equation is usually written: s =s8 ?(s8?so)e??/?c [l] where s is the true stress, ? is true strain, cC is a constant called the characteristic strain, s8 is the asymptotic stress approached at high strain values, and so is the threshold stress at which the plastic deformation begins. While this expression has not been universally accepted as yet it does contain certain features which are consistent with experimental stress-strain behavior. In a more recent publication Hsu, Davies, and Royles3 employed the concept of generalized strain proposed by seth4 and identified a method for linearizing the stress-strain plot. In this approach the generalized strain was given by: where 7 is the generalized strain, 1 is the instantaneous length, 1, the datum length, and n is a constant called the "coefficient of strain measure". A value of n was said to exist which would yield the linearity: s —s+ S[.-(tf] [3] In recent studies of both these approaches, it has been found that while the Voce equation and the gen-

Jan 1, 1970

By Gopalan Ramadorai

Tailings water from primary flotation concentrators usually contains minor amounts of pollutants such as heavy metals, cyanide and solubilized molybdenum, which are solubilized in the flotation process. A review of various techniques to reduce pollutants to acceptable levels is presented. Generally, molybdenite ores are processed by conventional size-reduction techniques, followed by flotation to produce a metallurgical-grade concentrate of 88% to 92% MoS2. Reagents commonly used in the milling process include: vapor oil (collector); pine oil, MIBC (frother); Dowfroth 250 (water-soluble frother); lime (rougher pH control); and sodium cyanide (Fe and Cu depressor). For lead depression, Nokes reagent is stage-added to the regrind mills and cleaners. Flocculant is added to obtain clear overflows in the intermediate thickeners.

Jan 9, 1978

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By A. B. Parsons

NOT every organization on reaching the relatively ripe age of three score and fifteen can say with truth that its purpose and objects remain precisely the same as prescribed by its founding fathers. Of course, constancy of purpose may be something else than unalloyed virtue. It could merely reflect slavish worship of tradition, intellectual stagnation, or sheer inertia. On the other hand, it could establish the fact that the founders were men possessed of broad outlook, of prophetic vision, and of an acute sense of direction. In addition to charting the course with precision, the founders of the A.I.M.E. surely showed a flair for expressing clearly in a few words what others might say obscurely in many words. To quote verbatim from the "call" for the meeting, in 1871, the proposed organization was to have: "two great objectives: "First, the more economical production of the useful minerals and metals. "Second, the greater safety and welfare of those employed in these industries." This text underwent some refining on several subsequent occasions but today the ultimate product, as set forth in the Constitution reads: "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means." The original call was dated "Wilkes-Barre, Pa., April, 1871," and was signed by Eckley B. Coxe, of Jeddo, and by R. P. Rothwell and Martin Coryell, both of Wilkes-Barre, each of the three subscribing himself as "mining engineer." The authors proceeded to explain briefly just how it was proposed to achieve these objectives: "In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed, as the free interchange of experience among those actually engaged in these industries; and this object has been accomplished mainly through the medium of `Institutes,' `Associations,' or `Societies,' composed of those engaged in these occupations, and by the periodical publication of `essays' or `papers' communicated to such societies by their members. "It must be evident to all practical men that the interchange of the varied experience

Jan 1, 1947

By J. A. Stachura

Continuous mining machinery provides the coal industry with one way to compete for a larger share of the total energy market. Various types of machines are discussed and some of the problems with continuous miners, encountered by operators, are reviewed. Equipment manufacturers are working with mine personnel to provide solutions for problems that arise. While coal production over the past 25 or 30 years has been on a horizontal plane, coal's share of the total energy market has declined. To participate more effectively in this total energy market, it is necessary to produce coal more efficiently. It is the obligation of all management, employes, and mining departments to gear the deep mining industry to the rapid progress and changing of today's modern industry. This can be accomplished in the near future with the selection of the proper type of continuous miner best suited to each operator's individual situation. In most mining operations there is tremendous incentive to undertake the continuous mining program. It can reduce the size of the mine greatly by permitting a minimum of working places; it makes pillar recovery work more efficient from the standpoint of overall cost, amount of coal recovered, and safety. The work force can be reduced materially permitting closer and more efficient supervision. It simplifies maintenance because equipment can be more readily standardized. The trend of the coal market favors the use of continuous mining machines. Although there appears to be a general feeling that continuous mining is still a relatively new program and will be slow in replacing conventional mechanical equipment, the fact is that tremendous strides have been made since the first machines were installed in 1948. This program is advancing at approximately the same rate that mobile loading machines replaced hand loading. From 1948 to 1955 there were approximately 450 continuous mining machines in service. In October 1959, a survey revealed that there were more than 700 continuous mining machines in service. Many operators have expressed a desire to undertake this program, but they feel that they could not do so at this time because of one or more of the following reasons: 1) the thickness of their coal seams, 2) seam characteristics, 3) soft bottoms, 4) bad roof conditions, 5) size consist, 6) insufficient flexibility in machines, 7) difficult ventilation problems, and 8) high maintenance costs. With the realization on coal about the same today as it was in 1948, or slightly less and since coal is still failing to participate to a greater degree in the total energy market, it is not surprising that the coal industry is desperately exploring more economical methods for deep mining. The manufacturers are aware that the coal industry is willing to invest in continuous miners if the equipment is built for maximum flexibility, will produce higher tons per man, and assure long life between overhaul programs. CONTINUOUS MINING MACHINES Before discussing details regarding the selection of a continuous miner, let us have a preview of some of the continuous mining machines which are available to the coal industry today. Jeffrey Manufacturing Co.: The machine shown is the Jeffrey 76 A.M. Colmol. This is their most widely used miner, and has been particularly successful in central Pennsylvania and in high-wall mining in western Kentucky. One of the outstanding features of this auger-type miner is its portability. The entire mining range can be changed from its lowest point to the maximum height without stopping the mining operation. Jeffrey 76 B.M. Colmol: This machine is similar to the 76 A.M. model; however, it is built bigger and stronger for a mining range of 50 1/2 to 72 in. This is the model that is now available (Fig. 2). Jeffrey has added two arms to the top row, omitted the odd arm in the bottom row, thus permitting a 50 pct larger throat opening. This eliminates one

Jan 1, 1961

By K. E. Brown, G. H. Fancher

An 8,000-ft experimental field well was utilized to conduct flowing pressure gradient tests under conditions of continuous, multiphase flow through 2 3/8-in. OD tubing. The well was equipped with 10 gas-lift valves and 10 Maihak electronic pressure recorders, as well as instruments to accurately measure the surface pressure, temperature, volume of injected gas and fluid production. These tests were conducted for flow rates ranging from 75 to 936 B/D at various gas-liquid ratios from 105 to 9,433 scf/bbl. An expanding-orifice gas-lift valve allowed each flow rate to be produced with a range of controlled gas-liquid ratios. From these data an accurate pressure traverse has been constructed for various flow rates and for various gas-liquid ratios. A comparison of these tests to Poettmann and Carpenter's correlation indicates that deviations occur for certain ranges of flow rates and gas-liquid ratios. Numerous curves are presented illustrating the comparison of this correlation with the field data. Poettmann and Carpenter's correlation deviates some for low flow rates and, in particular, for gas-liquid ratios in excess of 3,000 scf/bbl. These deviations me believed to be mainly due to the friction-factor correlation. However, Poettmann and Carpenter's correlation gives excellent agreement in those ranges of higher density. This was as expected and predicted by Poettmann. He pointed out that their method was not intended to be extended to those ranges of low densities whereby an extreme reversal in curvature occurs.l As a result of these experimental tests, correlations using Poettmann and Carpenter's method were established between the friction factors and mass flow rates which are applicable for all gas-liquid ratios and flow rates. Definite changing flow patterns do not allow any one correlation to be accurate for all ranges of flow. INTRODUCTION The ability to analytically predict the pressure at any point in a flow string is essential in determining optimum production string dimensions and in the design of gas-lift installations. This information is also invaluable in predicting bottom-hole pressures in flowing wells. Although this problem is not new to industry, it has by no means been solved completely for all types of flow conditions. Versluys,2 Uren, et al, 3 Gosline,4 May,5 and Moore, et al,6,7 were all early investigators of multiphase flow through vertical conduits. However, all of these investigations and proposed methods were very limited as to their range of application. Likewise, many are extremely complicated and therefore not very useful in the field. Only in the last decade have any significant methods been proposed which are generally applicable. The most widely accepted procedure in industry at the present time is a semi-empirical method developed from an energy balance, proposed by Poettmann and Carpenter8 in 1952. Their correlation is based on actual pressure measurements from field wells. Accurate predictions from this correlation are limited to high flow rates and low gas-liquid ratios. Although this method will be discussed in detail later, it should be pointed out that two important parameters, namely the gas-liquid ratio and the viscosity, were omitted in their correlation. The viscosity was justifiably omitted since their data was in the highly turbulent flow region for both phases, and most wells fall in this category. The gas-liquid ratio was incorporated to some extent in the gas-density term. In 1954, Gilbert9 presented numerous pressure gradient curves obtained from field data for various flow rates and gas-liquid ratios for the determination of optimum flow strings. However, no method is presented for predicting pressure gradients except by comparison to these curves. Baxendell, et al,10 proposed a method based on Poettmann and Carpenter's procedure

Established as a Division November 17, 1948 B W Gonser, Chairman J C Kinnear, Jr, Past Chairman H H Kellogg, Chairman-Elect R C Cole, Vice-Chairman, '58 A E Lee, Jr, Vice-Chairman, '59 W R Opie, Vice-Chairman, '60 R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1957

By C. G. Rhodes, D. Kramer

High-field critical transport current density (J) measurements at 4.2 °K as a Junction of applied magnetic field (H) were made on samples of cold-rolled and annealed columbium with H parallel to J. Microscopic examination of the samples revealed a well-defined planar fiber structure produced by the cold rolling. J was found to he lower when fibers are parallel to the direction of magnetic field penetration than when they are perpendicular. This effect may he a consequence of the interaction of flux movement with fiber boundaries. THE severe changes in microstructure brought about by cold working superconductors leads to profound changes in their superconducting behavior. In particular, the ability of a superconductor to carry a transport current with zero resistance (the maximum value of this current density will be called "J" in the presence of large external magnetic fields (to be referred to as "H") is greatly influenced by the microstructure. In the case of columbium, LeBlanc and Little1 and Autler et a1.2 have observed an increase in J due to cold work. LeBlanc and Little also observed an anisotropy in J in cold-rolled columbium strips, which Hake et al.3-6 have shown to depend upon the angle between H (H ? J) and the rolling plane. An increase in J due to cold work has been found in a variety of high-field superconducting alloys3'4'7-9 as has the anisotropy effect.10 First explanations of why cold work raised J invoked the idea that dislocations carried the high-field supercurrents,8,11 since cold working drastically increases the dislocation density and presumably the number of supercurrent paths. However, recent ideas on the nature of high-field superconductivity together with new experimental evidence reveal that the bulk of certain superconductors can remain superconducting in high fields while carrying high transport currents. These later developments have been discussed by Berlin-court and Hake12 and a comprehensive review has been prepared by Berlincourt.13 According to the ideas of Gorter14 and Anderson,15 one would expect that the influence of microstructure on high-field supercurrent density will depend on tine interaction between microstructure and penetrating flux and on the direction of the Lorentz

Jan 1, 1965

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By Frederick T. Fischer

INTRODUCTION Post-Lower Ordovician karstification on a continental scale produced a wide-spread paleoaquifer in the upper portion of the Knox Group of the Southeastern United States. The presence of economic zinc deposits in the Knox of Tennessee is considered to be a con- sequence of this paleoaquifer(1). During The New Jersey Zinc Company's initial exploration of the middle Tennessee region the known artesian nature of modern Knox water and its potentially adverse effect upon mining activities was a matter of concern. This concern intensified as a mining situation appeared imminent and a program of hydrologic investigation was begun in early 1969 and continued through August 1972. The preliminary findings of this work were reported at the AIME World Symposium on Mining and Metallurgy of Lead & Zinc in 1970(2). This paper presents additional data acquired during subsequent stages of the program and relates the hydrologic relationships to the overall geologic framework of the area. PHYSICAL GEOGRAPHY The Elmwood mine is 85km east of Nashville and 8km southeast of Carthage in Smith County, Tennessee (Figure 1). Its physiographic location is in the Central Basin of Tennessee, a basin resulting from erosional breaching across the Nashville Dome of the Mississippian strata which now form the bordering Highland Rims. Both the Central Basin and Highland Rims are divisions of the Interior Low- lands Province. Outcropping rock units of the Central Basin are predominantly Middle Ordovician limestones with scattered high hilltops capped by Devonian and Mississippian strata. One outlier

Jan 1, 1977

By David M. Hopstock

The performance of the most common type of low-intensity dry magnetic separator is analyzed on the basis of fundamental physical principles. Expressions are developed for estimating the optimal choice of design and operating parameters for beneficiation of magnetite ores. By proper choice of these parameters either a high-grade concentrate or a low-grade tailing can be produced from an incompletely liberated feed.

Jan 1, 1976

By Joseph F. Shirley

A froth flotation plant to recover byproduct molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning byproduct molybdenite plant design can be suggested that would be valid for most processes. The term byproduct molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals. Thickener It is considered essential that the feed to a byproduct molybdenite plant be thickened prior to being treated for molybdenite recovery for the following reasons: 1) Thickening allows the rougher and any preconditioning stages to be operated consistently at the optimum percent solids. 2) Generally, the size of equipment used for pretreatment and the rougher flotation is considerably smaller and less expensive than if the copper flotation concentrates were treated directly. 3) The removal of as much water as practical by thickening removes flotation reagents added in the copper flotation circuit, especially frother which can be quite troublesome in a byproduct molybdenite plant. Although thickening of the molybdenite plant feed has long been recognized as necessary to optimum metallurigcal results, very often this area has been designed poorly. The thickener should be sized so that it can produce a consistent thickened product containing 60 to 65% solids without the use of flocculants. Some plants are only able to thicken to 45 to 50% solids consistently while other plants let the percent solids vary from 45 to 60% over a 24-hr period. While the former is more desirable than the latter, in many cases better metallurgical results could be obtained if the percent solids could be held consistently close to 60%. Probably the simplest and most satisfactory system of handling the thickener underflow is to spigot it into a sump, using a sphincter type valve for the orifice, controlled by a density meter. Another satisfactory approach is to use an ODS type pump to meter the underflow. There are other methods of handling thickener underflow which work satisfactorily as long as the amount of copper concentrates entering the thickener is relatively uniform. However, they often fail to operate satisfactorily when there are large fluctuations in the thickener feed rate due to fluctuations in ore tonnage and/or copper grade. If the percent solids in the plant feed could be held close to 65%. There is the possibility the molybdenite plant tailing would not have to be thickened prior to the copper filter plant. This means that the molybdenite rougher float would have to be conducted at 45 to 50% solids with all the cleaner tailings returned to the rougher for dilution. Admittedly, in some situations this approach would be impossible, but if capital or plant area is limited, it should be considered.

Jan 1, 1981

The John Fritz Medal was awarded in January, 1916, to Dr. Elihu Thomson, "For -Achievements in Electrical Inventions, in Electrical Engineering, and in Industrial Development, and in Scientific Research." The medal will be presented to Dr. Thomson at a meeting, to be held in Boston on Friday evening, Dec. 8, 1916, in the Central Lecture Hall of the new buildings of the Massachusetts Institute of Technology. The program of the evening will include adresses by John J. Carty, Chairman of the Presentation Committee of the Board of Award, E. W. Rice, Jr., President, General Electric Co., and Dr. Richard C. Maclaurin, President, Massachusetts Institute of Technology. The presentation will be made by Dr. Charles Warren Hunt, Chairman of the Board at the time the award was made, and the ceremonies will conclude with the response of Dr. Thomson. The John Fritz Medal is awarded from time to time for notable scientific or industrial achievement, and was provided for in a fund subscribed in memory of the great engineering pioneer, John Fritz. The award of the medal is made by a permanent board composed of four members from each of four American National Engineering Societies, namely, the American Society of Civil Engineers, the American Society of Mechanical Engineers, the American Institute of Mining Engineers and the American Institute of Electrical Engineers. The members of the 1916 Board are: CHARLES WARREN HUNT, Representing the A. S. C. E., JOHN A.. OCKERSON, GEORGE F. SWAIN, CHARLES D. MARX. JOHN R. FREEMAN, Representing the A. S. M. E., AMBROSE SWASEY, JOHN A. BRASHEAR, FREDERICK R. HUTTON. ALBERT SAUVEUR, Representing the A. I M. E., E. GIBBON SPILSBURY, CHARLES F. RAND, CHRISTOPHER R. CORNING.

Jan 12, 1916

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

By John E. Sweet

THERE have already been so many subjects of a purely mechanical nature presented to the Institute of Mining Engineers, that it is unnecessary for me to apologize for adding another to the list. When a new invention, or what is supposed to be a new invention, claiming simply an improvement on the well-known devices, is to be described, it is usual to point out the defects of the old and give a history of the object or the art up to date. But, as no doubt a large proportion of the members of this Institute know as much, or more, about the history and use of the steam-engine indicator than I do myself, I will not further preface the subject, than to remind you that what called for the Richards's improvement on the Watt's indicator was high speed ; that the leading improvement was the reduction of momentum in the reciprocating parts; and that this was accomplished by making the parts lighter, and reducing the travel of the heaviest of them, and consequently the speed and momentum. The use of the indicator has been extended, for the speed of steam-engines and other prime movers has been increased, until one engineer at least, John Cooper, of Philadelphia, says, "I want an indicator that will work up to a thousand revolutions." Mr. Thompson, of the Buckeye Steam-Engine Company, of Salem, Ohio, has improved on the Richards's indicator by another reduction in the momentum, which is done by putting the parallel motion nearer the fulcrum of the pencil arm, reducing both weight and travel. The characteristic feature of the indicator I am going to illustrate is a still further reduction in the same direction, which is accomplished by dispensing with the parallel motion altogether. As is often the, case, in putting a simple idea into shape, some difficulties

Jan 1, 1879

By D. R. Wieland, H. T. Kennedy

The object of the work reported here was to determine the content of elemental sulfur in gaseous methane, carbon dioxide, hydrogen sulfide, and in mixtures of these gases, at pressures and temperatwes encountered in natural gas reservoirs. Sulfur content at equilibrium is reported for pure methane, carbon dioxide, hydrogen sulfide, and on three binary mixtures of each of the three pairs of gases at pressures of 1,000, 2,000, 3,000, 4,000, 5,000 and 6,000 psia and at temperatures of 150°, 200° and 250°F. In addition, the sulfur content of three ternary mixtures at the same temperatures and pressures are reported. The results indicate that the sulfur content is higher in the gases at higher temperatures and pressures. The content is highest in hydrogen sulfide, intermediate in carbon dioxide and lowest in methane. INTRODUCTION At ordinary pressures and temperatures, the concentration of a nonvolatile material, such as sulfur in a gas at equilibrium, is a function of the vapor pressure of the material and is independent of the nature of the gas. As the pressure and temperature increase, the gas assumes some of the properties of liquids, including the power to dissolve other liquids and solids, to an extent dependent on the nature of both the gas and the material dissolved. At equilibrium, the content of sulfur in the several gases considered here may thus be considered as solubilities which are fixed for a given composition of gas, temperature and pressure. The study of the solubility of elemental sulfur in gases is of interest because sulfur is sometimes present in reservoirs producing natural gas and must be present in the vapor phase. Upon reduction of pressure and temperature, the sulfur precipitates from solution in the reservoir and in the tubing and fittings. Due to the fact that the greatest pressure drop in the reservoir is around the wellbore, the volume of sulfur precipitated will be greatest in this locality and can cause a substantial reduction in the permeability of the formation in this area. As the natural gas flows up the tubing string, the pressure and temperature are further decreased, causing further sulfur precipitation. If the volume of free sulfur is large and remedial measures are not taken, complete plugging of the tubing can occur. Knowledge of the content of sulfur as a function of composition, temperature and pressure will enable the operator to determine what changes in pressure and/or temperature are necessary to keep the sulfur in solution. If the sulfur solubility is large and can be controlled, the operator may desire to produce the well at a high wellhead pressure and temperature and reclaim the sulfur at the surface. The high solubility of sulfur in hydrogen sulfide (5.6 per cent by weight at 5,000 psi and 200°F) suggests the feasibility of recovering sulfur by injecting this gas into sulfur-bearing reservoirs and expanding the produced gas to precipitate out the sulfur. The present project was designed to measure the solubility of sulfur in carbon dioxide, methane, hydrogen sulfide and mixtures of these three gases at various temperatures and pressures. These gases were the major constituents of the gas well where plugging by sulfur was encountered. A study of the published literature shows no data on the solubility of sulfur in any gas, although Hannay and Hogarth,' in 1880 reported that it was soluble in carbon disdlide above the critical temperature of carbon disulfide. EQUIPMENT AND PROCEDURE Fig. 1 shows the layout of equipment employed to bring gases to equilibrium with sulfur and to isolate the quantity of sulfur contained in a known volume of gas. Pure gases were measured in the charging bomb at known temperatures and pressures and displaced into the reservoir bomb to make up the desired mixtures. When equilibrium was achieved

By C. S. Allen

With increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration ? Deceleratien-or-retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. Types or Braking Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the srrew-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application—which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse Direction.-This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck,, them (which reverses the connections to the motors) and then to apply power. Theoretically, this should be done only in an emergency, but locomotives in mine service are frequently thus treated., Dynamic braking is retardation of the locomotive by the motors acting as generators, which take no power from the line.

Jan 1, 1942

By C. S. Allen

With increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration ? Deceleratien-or-retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. Types or Braking Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the srrew-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application—which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse Direction.-This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck,, them (which reverses the connections to the motors) and then to apply power. Theoretically, this should be done only in an emergency, but locomotives in mine service are frequently thus treated., Dynamic braking is retardation of the locomotive by the motors acting as generators, which take no power from the line.

Jan 1, 1942

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry' extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.' These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952