Search Documents

By Walter Snelling

IN the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I 'experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment.

Jan 4, 1915

By R. R. Morral, F. M. Krill, K. T. Aust

THE occurrence of twins in aluminum ingots cast under certain conditions has been well established. For instance, Herenguel and Lacombe1,2 have observed a twinned columnar structure in 99.5 and 99.9 pct Al, solidified by continuous or semicontinuous casting. The structure, which they termed "basaltic," appears in the form of elongated crystalline fibers of alternating luster. Herenguel and Lacombe2 found sections of flat crystalline plates composed of twin crystal plates, in which the twin plane (111) and a [I121 direction contained in the twin plane are parallel to the principal heat gradient. This orientation relationship is different from the usual orientation texture observed in cast face-centered cubic metals, where the [100] direction is approximately parallel to the long columnar axes lying in the direction of growth." A large amount of twinning has also been observed by the present authors in semicontinuous cast aluminum of 99.2 pct purity, Fig. 1. Mondolfo4 has suggested that the twinned cast structure forms by a deformation twinning process as the result of uneven cooling stresses within the ingots. This suggestion appears to be inconsistent with the large amount of twinning observed in the semicontinuous cast ingots and with the large difference of dendritic

Jan 1, 1953

IN presenting the medalist, Scott Turner, director of 'the Bureau of Mines, said in part: "Mr. Blaylock is a Canadian by birth, training, ex-perience and preference. He was born in the Province of Quebec, graduated from McGill University in 1899, and immediately thereafter became an employee of the company for which he is now general manager. His outstanding achievements have been the acquisition for his company of the Sullivan mine, and the organization of a metallurgical staff, which, under his leadership and personal direction, solved the difficult problems pre-sented by the extraordinarily complex lead-zinc-silver ores of the Sullivan mine. "By title only, I will suggest to you the high lights of his career: (1) Development, of the great mine at Kimberley, and a huge plant at Trail. (2) Discovery and application of a successful differential flotation process for Sullivan ore which had previously not re-sponded to any process. (3) Improvements in lead-blast-furnace and refinery practice. (4) Development of an electrolytic process for treatment of zinc concen-trates. (5) Development of an electric-furnace-smelt-ing-method for zinc-plant residues. Besides this, we recognize his great organizing ability, his gift of leader-ship, and the cooperative spirit he always displayed.

Jan 3, 1928

By D. E. Peacock, B. Harris

The mechanical behavior of a niobium (columbium)TUNG alloy containing 20 wt pet Ta. 15 wt pet W, and 5 wt pct Mo has been studied in the temperature range 77° to 423°K. All specitrzens tested, apart from those into which oxygen was introduced deliberately, were fully recrystallized at 1500°C, had an average grain diameter of approximately 0.03 mm, and a combined carbon, ox-vgen. nitrogen, and hydrogen content of not not more than 250 ppm The meckatnical behavior of this alloy was found to be similar in seine respects to that of unalloyed bcc transilion metals. Both yield and flow stresses were sensililae to changes in deformation rate and both increased rapidly as the temperature was lowered below 150°C. A detailed examination revealed, however, that most of the temperature dependencc of the yield stress could be accounted for by the temperature dependence of the elaslic, modulus, whish is not true of the unualloyed metals. In lension at moderate strain rates, the trunsition fvom ducfile to hvittle behavior occurred just belour room teunperature bur incveasing the oxygen content from 190 to 200 pptn raised the transition temperature to about 4000K. TUNGSTEN and molybdenum have been found to be very effective high-temperature solid-solution strengtheners of niobium, but the amounts of these elements that can be added are limited if the alloy is to retain useful room-temperature ductility. It has been shown, however, that partial replacement of niobium with tantalum lowers the ductile-to-brittle transition temperature of such alloys and allows larger additions of molybdenum and tungsten to be made. Some of the high-temperature properties of niobium alloys containing these elements have been reported by Bartlett et al.,' and the work presented here describes the low-temperature behavior of one of these, a solid-solution alloy containing, by weight, 20 pct Ta, 15 pct W, and 5 pct Mo. The elastic modulus, the temperature and strain-rate dependence of the yield and ultimate tensile stresses, and strain-hardening effects are discussed and compared with those of unalloyed niobium. EXPERIMENTAL MATERIAL AND PROCEDURE The material used in this investigation was produced from a 6-in.-diameter, double arc-melted ingot. This was can-extruded at about 1150°C to a 3-in.-diameter billet, and after annealing for 1 hr at 1345°C the billet was heated to 1315OC and part rolled and part forged to 0.5-in.-thick plate. The resulting material exhibited a cold-worked structure

Jan 1, 1965

By W. R. Shimer

IN his valuable report on Finishing Temperatures and Properties of Rails, I Dr. G. K. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying put the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. . Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development ,of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high per centages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility, than. rails of identically the same composition and section which were rolled, direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 3, 1915

By M. E. Wadsworth, R. C. Peterson, W. M. Fassell

The temperature and pressure dependence of the reaction of tantalum in oxygen were investigated from 500° to 1000°C at pressures from 10 mm Hg to 600 psi total oxygen pressure. Tantalum was found to oxidize linearly under the above conditions. Three distinct regions of temperature dependence were found with different energies of activation. From 500° to 600°C the rate of oxidation of tantalum was found to be essentially independent of the oxygen pressure at the pressure investigated. The oxidation rate increases rapidly with an increase in pressure from 600' to 800°C. The dependence of the oxidation rate on the bulk concentration may be expressed by V = k'?, where k' is the specific rate constant and ?=k1Co2/(l + K1Co2), where k, is the equilibrium constant for the adsorption of oxygen on tantalum. ONLY a limited amount of data has been presented in the literature on the oxidation behavior of tantalum metal. Some values of its oxidation rate were reported in the Corroston Handbook' and by McAdams and Geil.' The first extensive investigation of tantalum was the work of Gulbransen and Andrews." They determined the reaction rates of tantalum in O2 and N2. Their results indicate that this metal follows the parabolic law in the temperature range of 250" to 450°C in O2 at pressures of 7.6 cm Hg with an activation energy of 27,400 cal per mol. In nitrogen, the metal follows the parabolic law from 500" to 800°C at 7.6 cm pressure. All experimental determinations were of 2 hr or less duration and deviations from the parabolic rate conceivably could occur at longer times. A spectrophotometric study of the oxidation of tantalum by Waber, Sturdy, Wise, and Tipton' indicated good agreement between this method and the microbalance technique. The experiments were conducted in air from 220" to 350°C. The metal was found to follow the logarithmic law up to 320°C and the parabolic law at higher temperatures. The activation energies in the logarithmic region were reported as 12.57 kcal per mol and 12.0 kcal per mol, respectively, for the microgravimetric and spectrophotometric methods. In the parabolic region the activation energy was found to be 27.2 kcal per mol, in good agreement with the value of Gulbransen and Andrews." The present paper is concerned with the behavior of tantalum from 500" to 1000°C in oxygen at pressures ranging from 1/2 to 40.8 atm pressure. Earlier preliminary data by McKewan5,6 indicated the following facts concerning the behavior of tantalum: 1—At temperatures from 500" to 600°C, the metal followed the linear law. 2—At 575°C the rate of oxidation was found to increase with O2 pressure. 3—The Arrhenius plot in this temperature region was nonlinear. The nonlinearity of the Arrhenius plot was indicative of a more complex behavior than originally suspected for this metal.

Jan 1, 1955

By R. B. Adamson

The fatigue behauior of irradiated copper single crystals is compared to that of unirradiated crystals. Proton or electron irradiation did not substantially change the fatigue-lzj.e, fatigue-hardening-, or slip-line characteristics, while neutron irradiation did appear to alter these parameters. Postfatigue transrrzission electron microscopy did not reveal any marked structural differazces between irradiated and unirradiated specimens. Possible dislocatio~a mechanisnzs to explain the observed behavior are discussed. A LTHOUGH considerable work has been done to ascertain the effects of radiation on the tensile properties of metals (e.g., Refs. 1 and 2), little work of a basic nature has been reported on the effect of radiation on fatigue properties. Since it is known that fatigue properties are sensitive to conditions at the surface of the metal, it was felt that charged particle irradiation, whose penetration into metals is very small, might influence the fatigue behavior. To investigate this surface effect, irradiations with 10 mev protons and 1.5 mev electrons were conducted. The range of 10 mev protons in copper is about 0.236 mm; which is very small compared with the thickness of the specimens used (1.53 mm). The range of 1.5 mev electrons is somewhat larger, on the order of 0.665 mm.4 On the other hand, irradiation with reactor neutrons produces damage throughout the entire specimen, so neutron irradiation can be used to study the effects of bulk damage. The damage introduced by proton and neutron irradiation is expected to con!ist of large interstitial dislocation loops,5 tiny (<25A) vacancy loops," and/or various vacancy-rich regions called depleted zones.&apos; In the case of electron irradiation at about -173°C the damage is expected to consist of isolated Frenkel pairs.&apos; The effect of radiation damage on the fatigue properties of some engineering materials has been reported,g,10 but the results are not clear-cut or consistent. SPECIMEN PREPARATION Zone-refined copper was used to grow single crystals by a modified Bridgeman technique in an inert helium atmosphere. Using a seeding method, single crystals were obtained as bars about 6 in. long with a cross section of 3 by $ in. Immediately upon removal from the split-mold graphite boat in which they were grown, the very soft bars were embedded in a room-temperature setting plastic. They could then be cut into specimen lengths without introducing any long-range damage. Generally, four or five specimens plus one seed were obtained from each bar. The plastic material was dissolved away in acetone and the orientation of each sample was checked by the standard Laue X-ray

Jan 1, 1968

By Stewart, J. B.

THE property at which this work was done consists of a large deposit of potash salts occurring in massive beds of rock salt, overlain by 600 ft. of salt-impregnated shales and marls. It is in the Province of Cataluiia, Spain, about 45 miles from the railway station of Mauresa and about a mile south of Suria. In addition to sinking the shaft, the program of construction work laid out by the European owners (not Spaniards) included a single-track narrow-gage railroad from Mauresa to the mine; one large office building and several large shop buildings, all of brick and concrete with steel truss roofs; two extensive benches for the future recovery plant; and a large village of stone dwellings for employees. The pay-roll showed approximately 1200 to 1500 men employed. After two years&apos; operation, ending early in the autumn of 1920, the shaft had been sunk 325 ft. and still had an equal distance to go to reach the potash; all tunnels for the railroad were done and the road-bed $0 per cent completed; only a little more than the foundations were completed for all the large buildings, and the excavations of the benches were about 75 per cent done-while only a fair start had been made upon the employees&apos; village. This was the state of affairs when the European owners decided to offer this property under a one-year option to an American syndicate, providing that they agreed to carry on the entire building program and to sink the shaft as fast as was consistent with the quality of work which they demanded, for they wished the shaft to endure at least 200 years.

Jan 1, 1926

By Carl Belser

This paper summarizes the data on the oil-shale deposits of western Colorado, Utah and Wyoming. It is based on published reports by the U. S. Geological Survey, on the results of core drilling and sampling by the Bureau of Mines, on the drill cuttings from the Genera1 Petroleum well, on a recent unpublished report by the Geological Survey on the geology of Naval Oil-Shale Reserves No. I and No&apos; 21 and from information supplied by geologists of private companies who have investigated the Green River formation. The paper also contains a revised estimate of the grade and tonnage of minable thicknesses of oil shale of western Colorado. Introduction The oil shales of the Green River formation of Colorado, Utah and Wyoming comprise an important natural resource for the production of synthetic liquid fuels. The oil shale in western Colorado generally is more amenable to exploitation, apparently richer, and probably more persistent than in Utah or Wyoming. Work is now being done by the Bureau of Mines near Rifle, Cola. to ascertain the best procedures for mining the oil shale, producing shale oil from the oil shale, and converting the oil into more salable products. As a part of this program, holes were drilled and cores were taken of the oil shale on Naval Oil-Shale Reserve No. I. In addi- tion, drill cuttings were obtained from a well drilled through the Green River formation by the General Petroleum Co. about 18 miles northerly of the Naval Oil-Shale Reserve. Geology During middle Eocene time a broad, shallow body of water, now called Uinta Lake, covered northwestern Colorado and east-central Utah; a similar lake, known as Gosiute Lake, was in southwestern Wyoming Each of these contemporary lakes was bounded by high hills; the drainage was to the south. The Green River formation was laid down as sediments in the bottoms of these lakes. It is 3000 ft thick and has been divided into the following four members:

Jan 1, 1949

By L. G. Austin

If S (x) is the specific rate of breakage of size x and B (x, y) (see Table 1 for Nomenclature) is the cumulative breakage distribution function, the Herbst Fuerstenau2 assumption is that Inserting this assumption into first-order grinding equations it has been shown" that there are then simple analytical solutions to the grinding equations, as shown in Table 2. In this context "plug flow" is defined as all material passing through the mill in the same length of time, the residence time t. The term "n fully-mixed" means that the mill has a residence time distribution" which can be treated as if the mill were n equal fully mixed sections in series. In addition it has been shown that the assumption of Eq. 1 also leads to simple analytical solutions for closed-circuit, steady-state grinding with an ideal classifier at the mill exit returning oversize to the mill feed. The solutions are also given in Table 2, with µ as the ideal classifier cut size, C the circulation ratio, and Q (x) the size distribution of the circuit product. The specific surface area of these size distributions is where the density-shape factor k. is assumed to be constant with size. In practice, most methods of size analysis or area [ ] measurement have a finite lower limit, so that the integration is really performed from xm, to xm, For a realistic degree of grinding the value of So is dominated by the fine sizes because of the 1/x factor. Consider batch grinding of a feed of size y to y + dy. The batch grinding solution given in Table 2 is then [ ] The fresh surface area produced is the area of the fines plus the area of the original material remaining minus the area of the original material, [ ] Little error is introduced by neglecting the last term on the right-hand side since at t = 0 it is zero, and when t is significant the first term dominates because of the fine sizes produced. In addition, the form of P (x, t) for [ ] realistic values of S (x) 2t ax° is such that the major fraction of fresh surface produced is contained within the bottom 10% of weight of broken material, that is, for sizes for which P(x, t) < 0.1 (providing y is not near x.,). Thus for surface area purposes Eq. 3 can be approximated by [ ] becomes providing again that the feed sizes are coarse relative to xmi. Then the fresh area production is and W is the mass in the mill. The rate of surface production is WK, and the specific surface is Kt. From Table 2, the specific energy is mt/W so surface production per unit energy is [ ] Surface produced per unit energy input = KW/m (8) where m is the energy input of the mill. Clearly, identical reasoning applies to open-cycle, plug-flow grinding, with t replacing t, and Eq. 8 is obtained again. Considering open-cycle, fully mixed grinding, similar reasoning gives P(x) - t S(x) for surface area purposes, and

Jan 1, 1974

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company&apos;s property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company&apos;s property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By W. R. Hudspeth

AS an outgrowth of its spodumene recovery operation at Kings Mountain, N. C., Foote Mineral Co. has been recovering a heavy mineral by-product. Foote leased this idle plant in 1951, reactivated it, using a new spodumene recovery process, and purchased plant and properties in October 1951. While the operation at Kings Mountain is primarily concerned with the production of spodumene concentrate, pilot plant work determined that the pegmatites also contained heavy minerals including cassiterite. Plans were made to recover the heavy minerals as a by-product and the flowsheet incorporated these facilities when the mill was modified for the new spodumene recovery process. The orebodies consist of spodumene, feldspar, quartz and mica. Apatite, tourmaline, and beryl are present in small quantities. The wall rock is pre- dominantly hornblende shist. The heavy minerals, including cassiterite, columbite, pyrrhotite, monazite, pyrite, and rutile represent about 0.2 pct of the ore. The fine-grained heavy minerals are disseminated throughout the dikes, apparently unassociated with the spodumene. The pegmatites are quarried and secondary breakage is by mud-capping and block-holing. Power shovels load into trucks transporting the ore to a coarse ore bin. A Telesmith 10x36-in. apron feeder delivers the ore to an 18x36 in. Traylor Jaw crusher adjusted to discharge -3 in. product to a primary conveyor. The conveyor delivers to a 4x5-ft Tyrock single deck vibrating screen using 3/4 in. cloth. The screen undersize is elevated to the crushed ore bin. Screen oversize goes to an Allis-Chalmers Hydrocone Crusher fitted with 4 in. concave and set to deliver approximately 66 pct minus 3/4 in. The crusher discharge returns to the primary conveyor. The crushing and screening installation has a capacity of about 60 tons per hour. Spirals The crushed ore is delivered at a rate of 350 tons per day to two 6x8-ft Hardinge Pebble Mills, equipped with 20 mesh Ton-Cap trommel screens. The screen oversize is pumped to a 12-in. hydroclone for primary desliming. The hydroclone underfl spirals. There is no heavy mineral loss in the hydro-clone overflow. The spirals bank consists of eight 5-turn Model 24-A Humphreys Spirals. The top port and the last four ports of each spiral are blanked, the remaining nine port splitters are adjusted to remove about 5 pct feed weight. The heavy mineral rougher concentrates are upgraded on a Deister Overstrom table. The spiral concentrates contain approximately 4 pct heavy mineral, and the spiral reject, which goes to another section of the plant for spodumene recovery, contains about 0.03 pct heavy mineral. There is an interesting feature in the spirals installation. An adjustable splitter mounted on the discharge boxes splits out a mica fines product containing very little heavy mineral. The mica product is cleaned by spiralling and screening. Thus the spirals recover two products; mica, and a heavy mineral rougher concentrate. Table Treatment The rougher spiral concentrate goes to a Deister Plato table, modified to receive a Deister-Overstrom No. 6 rubber cover with sand riffles. The table is operated with a 5/8 in. stroke, 270 strokes per minute, and a slope of 1/2 in. per ft from feed to tailings side. There is no slope adjustment from motion to concentrate end. Wash water consumption is relatively high, since the large spodumene grains tend to report with the fine heavy minerals. A middling band about 4 in. wide is maintained in order to produce clean concentrate. The middling, representing about 10 pct of table feed, is recirculated by air-lift. A band of concentrate grade coarse spodumene occurs just below the middling. This is removed and delivered to concentrate storage. The table tailing, containing approximately 0.7 pct heavy minerals, is returned to the spodumene feed preparation circuit. The heavy mineral table concentrates are approximately 45 pct cassiterite, 33 pct columbite, 14 pct pyrrhotite and 8 pct monazite, together, with some rutile, pyrite, and copper from blasting wire. Concentrate is collected at 24 hour intervals. and dried. If the concentrate remains in wet storage appreciably longer surface oxidation takes place which seriously interferes with the subsequent magnetic separation process. About 150 lb of heavy mineral concentrate is produced per 24 hours and shipped to the company&apos;s plant at Exton, Pa. for final separation into tin and columbium concentrates.

Jan 1, 1952

By F. R. Hensel

ACCORDING to statements by Guertler,1 Smith and Hamilton were the first to study the copper-titanium alloys, but owing to the presence of large amounts of impurities their data are inconclusive. M. A. Hunter and I. W. Bacon later investigated the electrical conductivity and the temperature coefficients at room temperature. The present writers reported their results2 in November, 1930. Recently Droll published data on copper-titanium alloys3 which agree closely with those obtained by the authors. MATERIAL TESTED The titanium used was in the form of square sintered rods, the analysis of which runs as follows: titanium, 95.4 per cent; silicon, 0.7; iron,1.8; aluminum, 1.4; copper, 0.1; manganese, 0.05. . The ingots were prepared in a high-frequency induction furnace in air atmosphere. Their analyses are given in Table 1. Up to 5 percent titanium the alloys could be forged. Above that amount they were red short and broke up easily. Owing to their rapid absorption of nitrogen and oxygen from the air, the alloys with the higher amounts of titanium tend to form surface films which greatly increase the casting difficulties, especially when small masses of metal are handled. It was, however, possible to prepare sound ingots up to 25 per cent titanium.

Jan 1, 1931

For convenience, we tabulate below the weight systems contained in the Probierbüchlein: [Pound and centner weights used by merchants for ore, lead, and copper I frother = 20 or 50 centners (depending on locality) I centner (Stolberg & Eisleben) = 112 pounds. I centner (Nuremberg) =100 pounds I pound =2 marks =32 lot =128 quintlein-512 pennyweights =1024 beller I mark -16 lot -.64 quintlein =256 pennyweights = 512 beller 1 lot= 4 quintlein= 16 pennyweights= 32 beller I quintlein = 4 pennyweights= 8 beller I pennyweight = 2 beller Netherlands mintmasters&apos; weights for silver I mark =12 pennyweights=288 grains I pennyweight - 24 grains Assay weights for gold I mark= 24 carats 96 carat-grains. I carat = 4 carat-grains] The assayer&apos;s weights were miniature copies of the legal weights of his locality, intended, like the modern assay ton, to eliminate calculation. Each assayer made his own, not usually bothering about a given proportion between the true weights and the assay set, but maintaining the correct ratio between all the weights in any one set. The weights were quite small, to permit the use of less sample, but the exact size is nowhere stated in the Probierbüchlein. Even the legal pound varied considerably from place to place, depending on locality, and assayers would use different factors depending on the sensitivity of their balances, among other things. Agricola makes the assay centner equal to one actual drachma, by which term he means the German quintlein, or 1/12,800 of the full weight of the 100-pound centner. Schreittmann says that the 100-pound centner on the assay scale should be less than half a quintlein, i.e., the factor should be at least 25,600. Biringuccio says the assay centner might

Jan 1, 1949

By T. C. Shelton, W. M. Huang

One of the problems arising from the use of modern machines and systems in coal mining is increased emission of explosive gases into the mine passageways. Interest in degasification of coal seams has grown. The authors summarize the results of coal permeability tests done at Virginia Polytechnic Inst. on one of the fundamental aspects of the problem. There are undoubtedly many factors that affect the emission of gas from coal but the permeability of coal to gas flow would seem to be fundamental. However, there is very little information on coal permeability to gas flow available in the U.S. at the present time, despite the fact that such knowledge would appear to be significant in any degasification effort. Studies made recently in the mining engineering laboratories at Virginia Polytechnic Inst. have determined values of permeability on 1-in. cubes of selected coals. COAL PERMEABILITY The permeability values given in this paper are based on adaptations of Darcy&apos;s law formulated by Henry Darcy in I856 from experiments with fluid flow in porous media.&apos; Using air as the gaseous fluid, they were obtained by employing similar methods as are used to dete1:mine the permeability of petroleum and gas reservoir rock specimens. Permeability is. a measure of the ease with which fluids flow through a porous substance, and it is governed by the connected pores within a porous medium. If a few large-sized pores, fractures or channels are present within the medium, the medium can have great permcnability without significant porosity. It is reasonable to assume, therefore, that the permeability of coal, due to its structure, is based on fractures connecting the pore space left as the result of some degree of devolatilization or other changes of the substance from which coal was formed. The results of this irvestigation tend to validate this assumption in that the values obtained indicate a close relationship between the rank and permeability of coal. COALS TESTED AND PROCEDURE The coals whose permeability values were determined in this investigation are given in Table I.

Jan 1, 1962

By James A. Barr, R. B. Burt, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 8 1/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority under the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By J. A. Barr, R. B. Burt, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 81/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority und&apos;er the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 81/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority und&apos;er the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953