Search Documents

By Salinger, Herbert

WITH the large amount of metallurgical re- search work now being done and the constant effort of the engineer to effect economies of operation, I think it is a safe prediction that the next few years will see a great change in the handling of mine products. The well-managed mine, with sufficient ore reserves to warrant the necessary plants, will increasingly call upon the metallurgist and chemist for the solution of its problems. Shipping sorted ore or concentrate to the nearest smelter will not be the course followed. From ore to metal, or at least to a product directly salable to the consumer, will be the practice followed. As a consequence, mine managers will be increasingly interested in metal trade problems. By metal trade I mean the buying, selling, shipping, handling, and all the practices, forms and customs that go to make up the trade.

Jan 1, 1928

By W. C. Ellis

IN an ingot of germanium solidified progressively from the bottom by a method' devised by J. H. Scaff and H. C. Theuerer, examination discloses ex- IH. C. Torrey and C. A. Whitmer, Crystal Rectifiers. p. 364. 1948. New York. McGraw-Hill Pub. Co. tensive twin relationships. A slice taken about midway in a cylindrical ingot approximately 3/4 in. in diameter and 1 1/2 in. in length, after etching and polishing to delineate different orientations, is shown in fig. la. The orientations of the regions designated with letters were determined by Laue X-ray back-reflection methods and plotted on stereograms. The orientation relationships of the designated components were determined by comparing the values for the nine angles between the three respective cube poles of each orientation with the values calculated in a formal treatment of octahedral multiple twinning in cubic crystals. Germanium, diamond cubic in structure, has the octahedral twinning habit. I am indebted to K. H. Storks for the calculation of the angular relationships of cube poles in octahedral twinning to four orders. The set of values for the nine angles is distinctive of the order of twinning. Confirmation for a multiple twin relationship is obtained from the determined indices of the mirror planes. These exist for all orders of twinning through the third and for some of the fourth." If the orientations are not those for twinning, then the nine angles for the cube poles do not correspond in value and distribution to those formally calculated. Since all nine angles must correspond in values and distribution of values to the calculated ones, the Laue method with a precision of one or two degrees is adequate to establish or deny with confidence the existence of multiple twins. Regions of the same orientation can also frequently be identified by the optical reflections. For example, the narrow twin bands in A at 2: 00 o'clock have orientation B1. The interesting twin relationships shown schematically in fig. lb were found for the section in fig. la. Most of this slice was made up of orientation, A, appearing in widely separated regions. Of the four possible first order twins of A, three were present in this slice and are designated by B with subscripts. Four second order twins of A are designated by C with subscripts. It is worth emphasizing that two of these, C, and C,, are second orders of A through the first order missing in this section. Two regions, designated by D with subscripts are third order twins of A. D2 is a sixth order twin of D,. All orientations found were ascribable to multiple twinning, as if the orientations in this section originated earlier in solidification from a single nucleus. The presence of extensive multiple twinning to- gether with the absence of other orientations appears to be a characteristic result in many instances of solidification of germanium. Fertile conditions for twinning probably exist in the array of atoms in the diamond cubic structure. The high order twins in the section shown, it is reasonable to presume, are the result of progressive octahedral twinning through several generations in the material freezing earlier. Some of these generations do not appear in this section, it is suggested, because their orientations with respect to the growth direction were unfavorable for survival. The extensive twinning is probably promoted during solidification by constraint imposed by volume increase, and to an irregular growth front. Twinning may also be due, in part, to the attempt of the solidifying region to attain the orientation most favorable to the growth direction (maximum thermal gradient). The nucleus for a twinned orientation could have its origin in a "stacking fault" on the close-packed octahedral plane. Further work is being done in which the course of twinning throughout an ingot is being studied. The results appear to be important in the general theory of solidification.

Jan 1, 1951

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state's annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state's annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By Eugene A. Stephenson

The writer apologizes for presenting this very elementary analysis of one aspect of proration, but a search of the literature failed to disclose any concrete illustrations of the effect of various proration formulas upon the allowable oil produced by tracts of different sizes. Many engineers have doubtless made somewhat similar calculations and are fully acquainted with the results. The various allocation formulas that are in use are based on one or more of the following factors: (1) wide-open well potential, (2) potential through an orifice, (3) uniform well allowable, (4) acreage, (5) sand thickness, (6) bottom-hole pressure, (7) productivity index, and (8) volumetric displacement. Of these, the unrestricted potential formula, or open-flow test, and the uniform well allowable are commonly regarded by engineers as those least likely to give each producer his proportionate share of the oil or gas, as represented either by acreage or by sand thickness, or both, except when the wells are located on tracts of large size. Unless the mechanical equipment that may be used during the potential test and the method of taking the test are both specified, the net result of the potential formula is to practically force the operators to use special equipment and adopt special procedures prior to and during the potential test, so as to secure the largest possible allowables. Much ingenuity and skill have been devoted to this,problem, but the general effect is to permit excessive allowables for very small tracts, and stimulate unnecessary drilling. It is interesting to compare some of the high yields from the Wilcox horizon at Oklahoma City with each other, as an illustration of the effect of an allocation factor based solely on potential (Table 5). One of the glaring instances is a well on a ½-acre lease, which had produced, as of September 1936, at the rate of almost 3,000,000 bbl. per acre. This is at least twice as many barrels as could have been present under the property if the reservoir had consisted of a tank of oil 200 ft, deep and 56 acre in area. Numerous combinations of acreage, potential, bottom-hole pressure, sand thickness, etc., have been proposed and are in use in various fields.

Jan 1, 1937

By K. Adam

Grinding in steel mills adversely affects the flotation of pyrrhotite. The electrochemical nature of inter action between pyrrhotite and active metals was investigated by contacting pyrrhotite with platinum at different applied potentials. Flotation tests, scanning electron microscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy were wed to examine the surface properties of pyrrhotite. The formation of hydroxide or oxide and sulfate species of iron through the oxygen reduction reaction at the cathodically polarized surface of pyrrhotite was shown to be the mechanism responsible for the reduced floatability of pyrrhotite.

Jan 1, 1985

By N. LILIENBERGS

DURING the past few years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice was to mike steel ingots of sufficiently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is ?worked up,? the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnance and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory, is, that the silver-clear blow-holes, without the blue oxide, can be welded by sufficient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the "blue" cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it ?dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of

May 1, 1906

By Walter O. Snelling

In the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment. Evidently some condition existed in the first experiment that had not existed in the second test, and here began a series of tests in which I sought by the change of one variable after another to arrive at the identical conditions which must have existed in the first experiment. Only the fact that the bottle of heavy oil used in the first test was still in its place,

Jan 1, 1915

By Robert Glass Cleland

WALTER DOUGLAS succeeded his father, Dr. James Douglas, as president of Phelps Dodge in 1916. Before assuming office, the new president had been assayer at Bisbee, superintendent of the Copper Queen, general manager of all the Phelps Dodge mining interests, and altogether had spent a full quarter of a century in various phases of the company's business. Energetic and imaginative, experienced and courageous, he had need of all these qualities before he surrendered the direction of affairs into younger hands, fourteen years later. For the period of his administration was one of sudden ebb apd flow, flush production, drastic curtailment, quick recovery, and near-disaster. In 1917, soon after Walter Douglas became president, Phelps, Dodge & Co., Inc., which had been formed in 1908 as a holding company, went through an internal reorganization for the purpose of simplifying the structure and changing it from a holding company to an operating company. The Copper Queen Consolidated Mining Company, which had the necessary charter power and authority to carry on the business of any and all the subsidiary com-

Jan 1, 1952

By A. J. McEvily, R. C. Boettner, C. Laird

The processes leading to fatigue failure in the low-cycle range were studied to obtain an understanding of the basis of Coffin's law. Particular attention was paid to the manner of mack nucleation and to the determination of the portion of the total lifetime spent in crack propagation. It was observed that cracks are nucleated at surface notches meated during reversed plastic deformation, Principally at grain boundaries, and that crack growth occupies greater than 75 pct of the fatigue life. When inclusions are present, they are often the primary sites of crack initiation. From consideration of the incremental distances advanced by a crack in each cycle and of the lifetimes of different materials, it appears that the universality of Coffin's law arises from the similarity of crack-tip strain for a given applied strain amplitude, irrespecti7:e of material. STUDIES of low-cycle fatigue have been particularly rewarding in that a simple correlation between fatigue lifetime and plastic-strain range has been shown to exist. This empirical relationship takes the forml,2 Nner=C [1] where N is the number of cycles to failure, Er is the plastic-strain range defined as the total plastic strain per cycle (the sum of the tensile plastic strain plus the compressive plastic strain), n, the exponent, is a constant independent of the material to a first-order approximation and often has a value of about 0.5, and C is a constant which for a number of ductile and metallurgically stable materials is approximately 0.65 for fully reversed strain.3 This relationship has been shown to be valid for a wide variety of metals and alloys and is often referred to as Coffin's law. However, it is yet not clear why so many different metals and alloys exhibit the same over-all behavior in the low-cycle range. Less is known about the mechanisms of fatigue failure in the low-cycle range than in the high-cycle range, but it is expected that the processes would have much in common. For example, an important characteristic common to both high-and low-cycle ranges is that fatigue crack propagation can occupy a considerable portion of the total lifetime. This has been shown by Laird and smith4 by a count of the number of ripples present on the fracture surface of copper specimens, each ripple corresponding to one cycle of load. On the other hand, some marked differences have been noted. For example, in copper,5 nickel, and aluminum4 there is a greater tendency for grain boundary cracking to occur as the strain amplitude is increased. The purpose of the present work was to study further the processes leading to fatigue failure in the low-cycle range and to obtain an understanding of the basis for the validity of Coffin's law. Particular attention has been paid to the manner of crack initiation and to the determination of the portion of total lifetime spent in crack propagation. MATERIALS A number of metals and alloys were tested, although more attention was focused on a particular few, once general trends had become apparent. Alloys were selected so as to investigate the effects of crystal structure, number of phases, stacking-fault energy, and impurity content. The materials in this grouping were: high-purity copper OFHC copper 1100 aluminum (commercially pure) 70-30 brass (Cu-30 wt pct Zn)

Jan 1, 1965

By K. A. Jackson, G. A. Chadwick, A. Klugert

The diffusion field ahead of a lamellar interfnce is analyzed using an electrical analog. A self-consistent solution is obtained for the shape of the interfnce and the diffusion field by an iterative process. The solutions presented here are for a 50-50 eutectoid or eutectic, The shape of the interface is found to he independent of growth velocity and lamellar spacing, and to depend on the relative values of interfacial free energies at the phase houndaries . The mode of growth of lamellar eutectics and eutectoids has been a subject of much interest for many years.1-4 Mehl and Hagel 1 have shown photomicrographs taken by Tardif when he attempted to determine experimentally the shape of an advancing pearlite interface; the results are completely ambiguous. Brandt' and schei13 have made approximate calculations of the composition ahead of a lamellar growth front. The shape of the advancing front and the composition distribution ahead of the front are difficult to calculate because one depends on the other. It is the purpose of the present paper to describe a method by which this calculation has been done. Lamellar-eutectic growth usually occurs under conditions where the growth is fairly rapid, and the interface temperature is close to the eutectic temperature. The growth rate is usually determined by heat flow. Eutectoid growth, on the other hand, can best be studied by quenching to some temperature, and allowing growth to proceed isother-mally. In both cases the growth is believed to be controlled by diffusion* rather than by the atomic kinetics of the transformation. This being the case, a single treatment of the diffusion equation will apply to both cases, provided the region of the interface in a eutectic may be considered to be isothermal. If a part of the interface could appreciably change its thermodynamic driving force by advancing ahead of or lagging behind the mean interface, then the two cases would not be similar. Eutectics normally grow in temperature gradients of the or-der of a few degrees per centimeter. The normal eutectic spacing is the order of a few microns. Part of the interface would have to extend many lamellar spacings ahead of the mean interface before it experienced sensibly different conditions. The interface temperature is usually a few tenths of a degree below the eutectic temperature so that temperature differences of the order of one-thousandths of a degree (a displacement of one lamellar spacing) would be unimportant. Protrusions large compared to the mean spacing do occur when one phase only grows into a eutectic liquid. This is usually a dendritic type of growth, and easily distinguishable from the lamellar mode of growth. A single treatment of lamellar growth will apply equally well to both eutectic and eutectoid decomposition. At the interface, which as shown above is essentially isothermal, the difference between the equilibrium eutectic temperature Teu and the actual interface temperature Ti, can be divided into two parts: 1) the composition varies across the interface, so that the local equilibrium temperature is not Teu; and 2) the interface is curved, so that the local equilibrium temperature is depressed according to the Gibbs-Thompson relationship. This undercooling can be written as Teu-Ti =?T = mAC(x) + a/r(x) [1] where ?C(X) is the departure of the composition at a point x on the interface from the eutectic composition, see Fig. 1, r(x) is the local radius of curvature at a point x on the interface, m is the slope of the liquidus line on the phase diagram, and a is a constant given by where s is the interfacial free energy, TE is the equilibrium temperature, and L is the latent heat of fusion. The calculations in this paper will be made only for the case where the phase diagram is symmetric, that is, the eutectic occurs at 50 pct, the liquidi have the same magnitude slope m at the eutectic temperature, and C,, the amount of B rejected when unit volume of a freezes, see Fig. 2(a), is the same for both phases. As shown in Fig. 2(b), the composition ahead of the a phase will be rich in B, the composition ahead of the ß phase will be rich in A. The composition at the phase boundary is the eutectic composition. The difference between the local liquidus temperature and the actual tempera-

Jan 1, 1964

By W. T. Burns

Attempts were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No. 1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles. The average composition of the furnace charges was as follows: Per Cent. Peer Cent. Copper. Precipitate,..........7.5.3 40 to 80 Purification cathodes,.....1.9 92 Refinery slag (oxide slag),.. 10.1 50 to 60 Electrolytic cathodes,... 2.1 99.9 Precipitate anode scrap,.... 3.1 99.0 Scrap copper,.........7.5 99.2 100.0 The slag from this furnace amounted to 46 per cent. of the total amount charged and was of the following average composition: Per Cent. Cu..............16.86 SiO2.............34.7 FeO.............18.8 A12O3.............13.0 CaO.............9.4 MgO.............2.7 S............... 0.47 As..............0.11 Sb...............0.006 Ag, oz per ton.....0.18

Jan 1, 1914

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By William P. Roe, James F. Ellis, W. P. Fishel

This paper reports the distribution of sulphur between iron and titanium in Fe-Ti-S alloys and in Fe-Ti-C-S alloys. The compound TiS was found, which exists as a separate phase at temperatures below 1200°C. Titanium in steels reacts with sulphur in preference to carbon. THE general relationship between sulphides and oxides suggests that titanium should form a sulphide having properties similar to those of titanium oxide. Specifically, titanium should form a sulphide having a high melting point, indicating a stable compound of low solubility in iron. In order for titanium to function as a desulphurizer or sulphur-fixing agent, it must form a stable sulphide. In order for titanium to be useful in steels as a sulphur-fixing agent, it must react with sulphur in preference to carbon; and to prevent red shortness, the sulphide formed must have solubility characteristics such that grain-boundary precipitation of a low melting phase be prevented. The terms desulphurizer and sulphur-fixing agent when used in this paper mean that titanium effectively ties up the sulphur as a stable sulphide of titanium and prevents the formation of FeS. The partition of sulphur between iron and titanium was studied first in a series of Fe-Ti-S alloys with carbon absent, and then in similar alloys with carbon present. It has been established1 a that titanium forms in Fe-Ti-S alloys a sulphide of undetermined composition which can be identified microscopically, and that the titanium-sulphur compound does not respond to sulphur printing. It has been suggested" that titanium acts as a sulphur-fixing agent, although little proof has been given. A report% f The Advisory Committee on Metals and Minerals summarizes the existing knowledge concerning substitutes for manganese in steels. Distribution of Sulphur Between lron and Titanium with Carbon Absent The alloys for this investigation were made by -melting Armco iron, metallic titanium, and iron sulphide in alundum crucibles in an induction furnace. The titanium was added after the other ingredients had melted. In these alloys it is recognized that some TiO, is present, since the melts were made in the air and since no other deoxidizing agent was used; therefore, some of the titanium was not available for union with sulphur. Thirteen ingots were made. Ingots 2 to 8 were cast in baked-sand molds; ingots 12 and 13 were cast in metal molds; and ingot 9 was allowed to cool in the crucible in which it was melted. All ingots were annealed at 900°C for 3 hr and were cooled slowly in the furnace. Subsequent information indicates that this anneal had no effect upon the titanium sulphide particle size, since the sulphide does not go into solution at this temperature. The ingots as-cast were approximately 8 in. long and % in. diam. The compositions of the eight ingots and the results of the partition of sulphur are recorded in Table I. Total titanium and total sulphur were determined by standard gravimetric methods. Sulphur, as iron sulphide, was determined by the evolution method. Boiling HC1 (1:4) liberates the sulphur from iron sulphide, but leaves the titanium sulphide practically undecomposed. A complete separation of titanium sulphide and iron sulphide cannot be made by digesting these compounds in dilute HC1 since titanium sulphide was found to dissolve slowly. The amount of titanium sulphide decomposed will depend upon the time in contact with the acid and upon the particle size of the sulphide. The point

Jan 1, 1952

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of complaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and insure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage o~ breakage en route. The small sizes present in a car-of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal. An Ohio dealer estimates the degradation in loading and shipment of West Virginia coals consigned to Ohio cities as follows: Pocahontas lump

Jan 1, 1950

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By William B. Plank

PRESENT enrollment of 182,361 students in the engineering schools of the United States and Canada represents an increase of 6.6 pct over the enrollment in these schools in 1951-52. Thus is brought to a halt the steady decrease in engineering enrollment that began with the close of the 1947-48 academic year, five years ago. The mineral engineering student picture is similarly encouraging. In the United States schools, 9453 students are preparing themselves for positions in the Mineral Industry. This is an increase of 8.3 pct over last year as compared with an increase of 6.6 pct in the total United States engineering enrollment. The rate of recovery for the mineral engineering group is thus more rapid than for the engineers as a whole.

Jan 4, 1953

By Charles M. Ryder

IN presenting this paper to the Institute I beg to mention, first, the results which I have obtained and the apparatus which I have employed, and to follow this with a brief description of the steps by which I have perfected this process. My present mode of testing is as follows : I obtain, either from the furnace or from the finished product in any stage in which it may chance to be, a small test-piece, usually about 4 of an inch square by 3 1/2 inches in length. I place this test-piece upon the poles of an ordinary electro-magnet, for about one minute, and thus magnetize it to its extreme limit. I then place it upon an indicator (which I will shortly describe), on which indicator there is already placed a piece of steel of similar form which has been magnetized in the same manner, the percentage of carbon of this second piece being definitely known. I then, by means of a scale, which forms part of the indicator, marked in degrees of carbonization, read the exact percentage of carbon contained in the piece under examination. My apparatus consists of an ordinary electro-magnet, connected with a suitable battery of moderate power, by which I magnetize the pieces as before described, and of an indicator which consists of a magnetic needle suitably mounted or suspended, so that it is free to deviate a few degrees only from the zero point, and having a rest, which is used to check the vibrations when in use, and to support its weight when not in use. At a right angle to the natural position of the needle I have a scale about 3 feet long, the zero point of which coincides with the natural position of the needle. This scale is marked in each direction from the zero point in degrees of carbonization. The marking of the scale is in accordance with the following rule: Taking the carbonization of the steel as a basis, I maintain the same proportion between the squares of the distances on the scale as exists between the percentages of carbon in the steel, for instance, if .08 of

Jan 1, 1877