Search Documents

By W. R. Johnson

In the spring of 1935 the writers undertook to compare the geomagnetic and direct-current earth-resistivity methods of tracing a concealed dike along its strike. As far as they are aware no such direct test has been attempted.# The area surveyed lies along United States Highway number 15 about one and one-half miles east of Chapel Hill, North Carolina, and northeast of Bolin Creek (Fig, 1). To the south of the highway is the flood plain of Bolin Crook, and to the north is a hill that rises almost to the elevation of Chapel Hill. A diabase dike, which strikes slightly west of north, out-crops in a. gully just south of the highway. Southward it has been covered by alluvium but northward outcrops again on the southeastern slope of the hill north of the highway. South of the highway the country rock is Triassic shale and sandstone, the northern limit of which is slightly north of the road. On the Geological Map of the United States I the pre-Triassic formations are shown as lower Glenarm and assigned a pre-Cambrian age. Since the ago of the Glenarm has been called into question in Pennsylvania 2, the writers prefer not to commit themselves as to the ago of these rocks further than to say that they are definitely pre-Triassic.

Jan 1, 1937

By L. E. PORTNER

INCREASING military demands on the petroleum industry have brought into bold relief the crude-oil reserves now available to meet combined military and civilian demands, emphasizing the necessity for a greater efficiency in recovery from what has been discovered than ever before, particularly in light of the absence of new discoveries. This situation-and the fact that the industry, as well as members of the Government charged with governing oil production, desire to meet all crude-oil demands made of the industry with the least loss in tangible reserves through production practices-paves the way for increasing application of sound principles of production engineering and conservation.

Jan 1, 1944

By George S. Rice

MECHANIZATION in coal mining is a phrase which has attracted world-wide attention, and those persons not engaged on the practical side of coal-mine operations seem to regard mechanization as a panacea for many difficulties of the industry. The term "mechanization" as now employed by experienced mining men is restricted to mean mechanical loading of coal at the face. In a broader sense mechanization in coal mining was begun nearly half a century ago with the introduction of compressed-air undercutting machines and locomotives and, later, of electrically operated locomotives, undercutting and shearing machines, and drills. The use of coal-cutting machines, which has increased until now about three- fourths of the bituminous coal produced is being mechanically cut, first displaced hand-picking except in a few long-wall mines, and later gradually displaced the dangerous and coal-smashing method of blasting-off- the-solid.

Jan 1, 1929

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By R. W. Raymond

THE absence of a convenient glossary of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as may be inferred from its great increase in length, as well as the numerous alterations which it has undergone. It could certainly be still further enlarged and improved; but I think a comparison of it with any of the glossaries of the same class now in print will show, at least, that it is an advance upon what has hitherto been accomplished. 1 shall be grateful, however, for further criticisms and suggestions; and I purpose at some future time to incorporate in a supplementary paper the results of such additional collections or corrections as I may obtain. To avoid too great prolixity, I adopted at the outset the following general principles: 1. To include the most important technical words and phrases used by American miners and metallurgists, or occurring in English books and periodicals.

Jan 1, 1881

By Halbert Powers Gillette

In every chemical reaction heat is either developed or absorbed, and this plus or minus heat of formation is as definite in quantity as the weights of the reacting elements. In this paper I shall show that each chemical element and each chemical radical has its own definite heat-valency,—a fact which, so far as I know, has hitherto escaped the attention of investigators, but, I feel sure, will be admitted after the demonstration here given, and may lead to some practical conclusions of value. When Berthelotys " law of maximum work " was found to have so many inexplicable exceptions, the pendulum of a scientific theory swung away from a recognition of the truth underlying that proposition; and this reaction went so far that not only has thermal chemistry been relatively neglected by recent investigators, but it is not uncommon now to find textbooks on physical chemistry which practically ignore all that Thomsen, Berthelot and others have done. To this temporary tendency of thought I attribute the failure to recognize the principles herein announced and explained. Not long ago, while studying tables of the formation-heat of various salts, I noticed that in this respect all potassium salts in solution differ from the corresponding sodium salts by 9.3 cal.1 I found also that similar differences exist between other salts, not only when the basic radical is varied, while the acid radical remains constant, but also when the acid radical is the variable. Thus chlorine salts in solution differ from bromine salts in this respect by 10.9 cal. Upon further study, I found that Thomsen had noted similar constant differences, but, so far as I can ascertain, he appears to have attached no great significance thereto.

Jan 1, 1904

By Byron W. Cheever

In working up the process which I described at the Chicago Meeting, May, 1884 (p. 163 of the present volume), for the estimation of phosphorus in iron and steel, I employed samples of steel obtained from one works only, and of a given brand. Since then I have had frequent occasion to test the process on other steels, and find that it works equally well. But some steels present certain colors which may mislead the operator; and I therefore propose a slight change in the directions formerly given. On the second page of my paper, in the second paragraph, I would substitute the following modified directions: Place the flask under the hydrant, till the solution is perfectly cold ; then add, gradually, strong ammonia, with constant stirring, till the solution is changed into a pasty mass and the ammonia is in slight excess; then add cautiously HNO3 (1.40 specific gravity)

Jan 1, 1885

By Charles Law McCabe, Lyndon H. Everett, Edna A. Dancy

It has been found that the carbide phase present at equilibrium in the system M-H2-CH4, at about 600°C, is MC for the rare-earth metals Ce and Pr. X-ray diffraction analysis showed that the monocarbides have fcc structures with lattice constants of 5.036 + 0.009Å and 5.131 + 0.001Å for CeC and PrC respectively. Gaseous equilibrium measurements were used to calculate the standard free energy of formation of the monocarbides from the elements. for the formation of (+ 1300) for the formation of PrC. THE rare-earthdicarbides, and their crystal structures, have been known for some years,l but only more recently were the carbides CeC,2,3 Ce2C3 2 and CeCS3 reported. In 1958 to 1959, Spedding et al. published work on the lanthanum-carbon system4 and other rare-earth metal-carbon systems,5 proving the existence of M2C3 and MC2, and measuring the lattice constants. They also demonstrated that tri-rare earth carbides, M3C, exist for the rare-earth metals samarium through ytterbium. However, they concluded that the cerium monocarbide reported by Brewer and Krikorian2 and by Warf,3 and given a fcc structure with a lattice constant of 5.130Å bythe former workers, was, in fact, cerium metal with carbon dissolved in it. They were also unable to find any evidence for the existence of Warf's CeC3, for which no structural details had been given. Even more recently, Palenik22 reported the existence of only M2C3 and MC2, having been unable to find any evidence for the existence of any other rare-earth carbides. There are no published experimentally derived thermodynamic data for the formation of any of these carbides, although Brewer and Krikorian6 have estimated values of for CeC, Ce2C3 and CeC2. The objective of the present investigation was; to determine experimentally the free energy of formation of any of the reported carbides of cerium and praseodymium, through a study of the rare-earth metal-hydrogen equilibrium. EXPERIMENTAL A methane-hydrogen mixture was circulated, in a closed system over previously prepared cerium or praseodymium hydride, and when equilibrium had been attained, the gas mixture was analyzed by selectively oxidizing the hydrogen and condensing out the water formed. The metal hydrides were used as starting material for convenience because, otherwise, the hydrogen in the gas mixture would immediately dissolve in the metals; in addition, the metals would not react with methane alone at the experimental temperature (around 600°C). The circulating system was based on that used by Browning, DeWitt, and Emmett7 for similar studies on iron carbides. It consisted of a quartz reaction vessel, all-glass circulating pump, analysis tube containing copper oxide that could be heated to 300" C by means of a small furnace, a solid CO2-methanol trap, and a double limb absolute manometer, Fig. 1. A cathetometer, capable of reading to 0.005 cm, was used to measure the difference in height between the two columns of mercury. In its final form, the reaction vessel was enclosed in an outer jacket, containing approximately the same pressure of hydrogen as that within, to reduce errors due to diffusion of hydrogen out through the fused silica of the reaction vessel., The circulating system was supplied with

Jan 1, 1962

By R. L. Templin, D. A. Paul

The modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 Ib. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately corrcct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements. a National Metals Handbook. b Intcrnatiunal Critical Tables. '' Aluminum Co. of America. " Based on density of alurminum (2.70). c Smithsonian Pliysical Tables.

Jan 1, 1931

By Charles M. Rolker

It is now three years ago that I wrote a paper on the fire which broke out in October, 1880, at the Chrysolite mine, Leadville, Col orado, of which I was at that time manager. The paper was read by title at the Harrisburg meeting in 1881, and was accompanied by plans and sections fully illustrating it. It was written to invite a general discussion of the course pursued in the management of that fire, since the various fragmentary and sometimes prejudiced or inaccurate newspaper accounts were not suitable to base judg ment on. The paper I offered, gave the facts as they appeared in the contemporaneous record which I had kept. At that time, a dif ference of opinion had arisen with an adjoining mine, as to possible damages entailed through the fire; and a law suit was talked of. In view of these circumstances, the President of the Chrysolite Company advised a temporary withdrawal of my paper. Somewhat later, I withdrew it entirely, because of the unlooked-for delay in * arranging the controversy referred to. It. has now, indeed, been amicably settled; but the lapse of time has deprived the matter of much of its immediate professional interest. To the urgent request of some of the members, that I should, at least, give a description of the fire- and gas-proof bulkheads employed, I yield with some hesitation, since I lay no claim whatsoever to orig inality in these devices, and therefore question the value of such a paper. The fire originated by accident, in the Chrysolite, a mine comprising extensive and more or less irregular workings, containing immense quantities of timbering, but partially packed with waste rock or earth. This class of mines is numerously represented at

Jan 1, 1885

By EDBIUND U. NORTH

IN making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that. the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By S. Acar, P. Somasundaran

The results obtained for the selective flocculation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is discussed. Dissolved iron, copper, and nickel (Fe, Cu, and Ni) species are found to affect the properties of natural chalcopyrite and pentlandite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation, and complexation of species

Jan 1, 1986

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By J. L. Huiatt, D. G. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated methods of recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite and carnallite. Six sulfate- chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2% to 22.2% K20, and recoveries by crystallization ranged from 85% to 99%. Sylvite flotation from chloride evaporites with amine collector, recovered 90% to 97% of the potash in a concentrate containing 54.3% to 60.3% K20. Fatty acid flotation of the high sulfate evaporite recovered 78% of the sulfate minerals in a 28%-K20 concentrate. Flotation of the remaining chloride minerals with amine collector recovered 80% of the potash in a 59.7%-K20 concentrate. Solar evaporation of 37 854 L (10,000 gal.) of brine recovered 99% of the potash in a crude evaporite containing 24.5% schoenite and 20% sylvite. Flotation in a 45-kglh (100-lblh) continuous flotation unit recovered over 95% of the potash in schoenite and sylvite concentrates, containing 28% and 62.3% K20, respectively. An economic evaluation is included.

Jan 1, 1985

SINCE I have begun to tell you of the semiminerals that serve as colors, I wish to tell you of azure and green azure, so that you may know what they are. I tell you first that there are two kinds of azure, one called ultramarine blue by painters, and the other German blue. Ultra-

Jan 1, 1942

By J. G. Koenigsberger

The electrical specific resistance of rocks in the field is measured by sending a current through a medium of great volume, compared to the electrodes, whose resistivity should be measured. The whole resistance can be determined by the Wheatstone bridge and the specific resistance calculated by a well-known formula. The resistivity of some rocks in place in Germany and in Switzerland is given; first, of a rock near the surface, and especially near electrodes. Practical applications are made in the determination: (1) of the continuity of a conducting orebody; (2) of the surface ares of an orebody; (3) in the detection of a water-bearing fault in a salt mine. Preliminary 'observations are described: (1) on the influence of the depth of ground-water table; (2) on the detection of gas under high pressure in coal seams. The observations in this paper of the electrical resistivity of rocks and soil in place are along the lines of the very interesting method and results of the Messrs. Gish, Rooney, Hotchkiss and Fisher. 1,2 All the work described has been done since 1920. Method Used The very simple method consists in the application to the rock of two plane circular electrodes of iron or brass of a suitable diameter, with the aid of a contact substance, and in measuring the resistivity in a Wheatstone bridge with alternating current of 100 to 400 Hertz frequency per sec.). The general formula is known to be R= R0 +d/4(1/a+1/b-1.7/l+0.8(a+b)/l2) (1)

Jan 1, 1929

By D. F. Stoneburner, G. Derge, Ling Yang

PREVIOUS investigations in this laboratory have shown the existence of electronic conduction in several molten metal sulfides and the specific conductance of a number of these has been measured as a function of temperature.' In order to better understand the electronic nature of these melts, the thermoelectric power of a molten FeS-solid tungsten thermocouple was measured and a value of approximately 55 µv per "C was obtained in the temperature range from 1200" to 1400c2 These studies have been continued and the thermoelectric power of several other molten metal sulfide-solid tungsten thermocouples have been obtained. The experimental arrangement is shown in Fig. 1. A Kanthal furnace was used, doubly wound to prevent any undesirable effects of an external field. A 1/2-in. McDanel tube was fitted with two vertical 5/8-in. McDanel tubes as shown. These tubes were about 2 in. apart. A graphite boat was used to hold a re-crystallized alumina boat in which the prefused sulfide was placed. Two probes were made using

Jan 1, 1960