Search Documents

By M. E. Learmont, I. Iwasaki

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1985

By N. I. Fisher, J. Shepherd

Statistical studies have been carried out on structural geological data collected across a large zone of roof failure 600 m (1968 ft) wide and at least 800 m (2642 ft) long in the Greta coal seam at Aberdare East Colliery. Two swarms of hundreds of minor, normal faults with throws commonly between 3 and 300 mm in the room and pillar workings are broadly coincident with roof failure. The faults have been classified into dip slip and oblique and strike slip types. Roof conditions have been classified into good; troublesome with subclasses scaly, heavy, gutter falls and wide, flat-roofed falls; and severely failed with subclasses very heavy roof, gutter falls and dome falls. Troublesome conditions are defined as those in which the height of the fall is less than or equal to 0.3 m, and severely failed conditions as those in which the fall height is greater than 0.3 m. Comparison of faults, roof condition and mining rate on a shift basis indicates that faults and roof failure are much more important than machine breakdowns in reducing mining rate. The effect of faults on roof conditions has been quantified using a concept called the "zone of influence," a rectangular area around a fault in which the fault has potentially deleterious effects. The spatial comparison of fault "zones of influence" with areas of roof failure wing Spearman's rank correlation coefficient shows that, while normal dip slip faults do not appear to be associated with roof failure, oblique slip and strike slip faults appear to be associated with roof classed as severely failed. The "zone of influence" of an oblique slip fault may extend up to 3 m on each side of it in the headings and up to 1.14 m in the cut-throughs. The fault "zone of influence" has geomechanical implications for the design of mine openings and Possibly represents the maximum length of a cantilevered roof beam likely to fail during mining, owing to a fault. Roof conditions could Possibly be predicted in blocks of &gin coal if the type of fault could be identified in oriented drill cores.

Jan 1, 1979

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining Engineer. Graduate of Colorado School of Mines, 1912, experienced in coal, lead manganese and limestone mining, wishes execu¬tive position. A-2146. Graduate Mining Engineer.-Discharged, reserve officer, age 32, single, 7 years' experience holding responsible executive positions, in iron, copper, and talc mining. Well recommended. A-4913. Mine Manager, Superintendent or Engineer. Age 41, graduate of Michigan College of Mines; 20 years' experience in responsible positions in connection with large operations; in iron, copper, pyrites, lead and zinc mines; successful in finding and developing orebodies, increasing production, and reducing costs. Desires a position with a future. A-4081. Mining Engineer.-Graduate from Polytechnicum, Stockholm; 14 years' practical experience in Sweden, United States, Belgium, and Spain, in iron-ore development, mining, and milling; thorough knowledge of English, French and Spanish; desires position as superintendent or assistant manager. Good references; member; now in Sweden. A-4914. Research Engineer. Now in Chile on the erection of a 50-ton mill with modern machinery for the treatment of Chilean nitrate. Desires connection from the first of next year; with firm operating in South or Central America. A-4915. Metallurgical Engineer. Junior member, age 26, single, graduate Columbia School of Mines; recently discharged as lieutenant in the heavy artillery. A-4916. General Superintendent. Technical graduate, age 35, desires position over a group of four or five mines or as assistant general superintendent for a large. company. Has had experience in superintending mines, construction work, opening new and abandoned mines, safety and effi-ciency engineering and handling organized labor. At present employed by a coal company in the middle West. A-4917.

Jan 11, 1919

By K. A. Natarajan, I. Iwasaki

The effect of poisoning on the behavior of platinum electrodes in redox potential measurements in metallurgical systems was studied in the presence of such inorganic surfactants as cyanide and sulfide and such organic surfactants as dodecylammonium acetate, trimethyldodecylammonium chloride, potassium ethyl xanthate, and potassium diethyl dithiophosphate (Aerofloat®). These chemical species represent, more or less, typical constituents encountered in leaching, flotation, and sewage treatment systems. Triangular wave voltammetry was used as the experimental technique to study the nature of poisoned surfaces. Among the species studied hydrogen sulfide and dodecylamine were found to form a resistant surface film affecting charge transfer. Platinum electrodes appeared to have a weaker tendency to adsorb sulfide species in alkaline pH ranges, while cyanide, xanthate, and dithiophosphate affected the normal electrode behavior differently. Possible methods of reactivation of a poisoned electrode by mechanical cleaning are suggested.

Jan 1, 1974

ALL that I have been able to tell you concerning the ordinary practice of parting with aqua fords I have striven to demonstrate to you as briefly as possible. Now, before passing on to speak of other things, I wish to teach you the method that you must follow in order to recover whatever is good in those chalky precipitates of that acid and all the silver that you put in; it was for this reason that I told you to save them in a cucurbit by themselves. This is called "water of whites" by the master parters, and in reality is nothing other than the precipitates of thick phlegm of aqua fords, white as chalk. If these were not extracted from the acid, the spirits of the infused materials [69] would be almost without

Jan 1, 1942

By D. C. Sisti

A technical evaluation of actual performance of the preparation facilities at Beaver Consolidated Coal Co.'s Stinson plant is presented, with special emphasis on sulfur reduction in 1-1/2 x 3/8 in., 3/8 in. x 28 mesh, and 28 mesh x 0 size fractions. Evaluation of the heavy medium section of the plant and the treatment of the 28 mesh x 0 coal is included. Design criteria considered for sizing and selection of equipment required to process 1-3/4 million tpy of raw coal on coals of divergent washability characteristics are summarized.

Jan 1, 1976

By O. B. Ellis, Eric R. Jette, John Chipman

In the study of the chemical reactions orcurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Hertyl and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schack-mann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete allalyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were re-melted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abnndoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the con stituents of basic open-hearth slag. Experimental Heats The first set of measurements on slag-metal equilibrium was made in the Research Laboratories of the American Rolling Mill Co, at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Rescarch Laboratories at Massachusetts Institute of Techology, and will be referred to as series B. Series A.—The induction furnace used has been described. Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By John Chipman, Eric R. Jette, O. B. Ellis

In the study of the chemical reactions orcurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Hertyl and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schack-mann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete allalyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were re-melted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abnndoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the con stituents of basic open-hearth slag. Experimental Heats The first set of measurements on slag-metal equilibrium was made in the Research Laboratories of the American Rolling Mill Co, at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Rescarch Laboratories at Massachusetts Institute of Techology, and will be referred to as series B. Series A.—The induction furnace used has been described. Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By Raphael Titi-Manyaka, I. Iwasaki

Chlorination and chloridization behaviors of pyrite, pyrrhotite, chalcocite, covellite, chalcopyrite, bornite, heazlewoodite, millerite, and pentlandite in chlorine, gaseous ferric and sulfur chlorides were investigated by thermogravimetric analysis. The reaction mechanisms are discussed in terms of theoretical weight changes, thermodynamic calculations, and X-ray analyses of reaction products. The experimental findings are in direct application to the development of a scheme for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from complex sulfide flotation concentrates.

Jan 1, 1977

By L. C. Uren, E. J. Bradshaw

This paper presents the results of a group effort by a number of University of California students and faculty members, and the authors attach their names primarily in the capacity of editors and interpreters of the data thus assembled. In addition to the writers, the following individuals have made substantial contributions in time and effort in the conduct of this research: Dr. A. J. Carlson, Associate Professor of Petroleum Engineering; J. E. Gosline, University Research Assistant; C. F. Bedford, G. W. Mikulasek and H. S. Conder, senior and graduate petroleum engineering students; H. Bachman, G. Spencer and G. W. Gard, mechanicians in the Department of Mining and Metallurgy. Acknowledgment is also due the Research Board of the University, the Department of Mining and Metallurgy, and Prof. F. H. Probert, Dean of the College of Mining, for continued cooperation in securing mechanical assistance and funds for the purchase and assembly of apparatus. Significance of the Pressure Gradient The expulsion of petroleum from its reservoir sand doubtless is due to expanding natural gas intimately associated with the oil, to the hydrostatic pressure of encroaching edge waters, and to gravitational influences. These forces may operate independently or collectively. In any case they subject the fluids stored within the reservoir sands to elevated pressures, thus causing movement of oil and gas through the productive formations toward the lower pressure of the well outlets. This movement is opposed by pore friction, capillarity and adhesion: resisting influences brought to bear by the reservoir sand on the moving fluids. The magnitude of the resisting force is influenced directly by the viscosity, surface tension and density of the oil, as well as by the properties of the gas. The more rapid the rate of flow, the greater will be the resistance offered, and the greater will be the energy consumed.

Jan 1, 1932

By K. A. Natarajan, I. Iwasaki

Electrochemical measurements were made wing chalcopyrite and pyrrhotite electrodes in aqueous solution containing a xanthute collector and ground ore mineral particles. The purpose was to investigate the electrochemical reactivity of ozone with respect to dissolved xanthute, surface adsorbed xanthute, and the sulfide mineral itself. Electro-chemical evidence for the removal of xanthate coatings from chulcopyrite, pyrrhotite, and platinum surfaces by ozone is presented. The oxidizing power of ozone is compared with that of oxygen and other common oxidizing agents to portray the superiority of ozone as an oxidant.

Jan 1, 1986

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 6, 1950

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By OTTO HERRES

UTAH has enormous deposits of high-grade bituminous coal. The United States Geological Survey estimates that there are 13,130 sq. mi. of land in Utah known to contain workable coal and these extensive fields contain 196,000,000,000 tons of coal. Growth in population and development of industry in the intermountain and Pacific coast regions will in time give Utah a place with the great coal producing states of the country. Even today, faced by adverse conditions in competition with cheap fuel oil from southern California, water-power throughout the western states in general, and comparatively high freight rates to its distant markets, the Utah coal industry is notable in many respects. In recent years, Utah has led the United States both in the percentage of its mines in class 1, mines producing more than 200,000 tons a year, and in average production per man per day, which was 6.01 tons in 1921. In Mineral Resources of the United States, 1921, Part

Jan 1, 1925

By K. A. Natarajan, I. Iwasaki

The meaning and the utility of redox potential (Eh) measurements in sulfide flotation systems are examined. Since some preliminary plant Eh and laboratory flotation data were available, experiments were made to establish the pH range at which a platinum electrode might be used for such measurements without much difficulty in aerated systems. Triangular wave voltammetry was used to study the surface conditions of the electrode immersed in pyrrhotite suspensions at different pH. The measured Eh both at the plant and the laboratory is interpreted in terms of the experimental water-oxygen line.

Jan 1, 1974

By I. Iwasaki, K. A. Smith

A chlorination process for treating metal sulfide flotation concentrates is described. The process involves low temperature chlorination combined with sulfur chloride conversion and selective oxidation to produce nonferrous metal chlorides, elemental sulfur, and ferric oxide in a three-stage fluidized bed reactor. The nonferrous metal chlorides may then be water leached, separated, purified, and electrolyzed to recover copper and nickel metals and to regenerate chlorine for recycling.

Jan 1, 1986

By A. E. Gorum, I. Cornet

Fatigrle of ionic crystals has been studied primarily in magnesinm oxide. under cyclic stress dislocations move irrreversibly; they multiply; slip bands form and grow; cracks mucleate and propagnte, and failure occurs. The use of ionic crystals such as MgO is advantageorus in such investigations because they are optically transparent. Individual dislocation Intersections with {100} surfaces may be observed with a standard microscope, using etch-pit techniques. Slip, deformation, crack .formation, and fracture in MgO crystals under cyclic stress are compared with cotrresponditzg processes in metals. ThE effect of cyclic loading in metals has been studied for many years. The appearance of slip lines is readily observed and the ensuing fracture may also be seen. From these observations it is possible to predict the behavior of a material and make an educated guess as to what is happening internally, but the actual changes taking place within the structure are not readily apparent. If one could obtain a material in which the individual glide components could be observed, it would be invaluable in determining the actual slip distribution resulting from cyclic loading as well as the distribution of slip in the neighborhood of a growing crack. Such a material is magnesium oxide. Dislocation arrays may be observed by means of etch pits

Jan 1, 1961

R. W. Raymond, New York City: From a study of Mr. Johnson's paper, I conclude that his apparatus is simple in construction and operation, and imitates in a revolving machine the movements of hand-shoveling. It does what a man would do in removing sand from the waste-water with a perforated shovel. I am sorry to say that I fear the present condition of the brown-ore mining industry in the East, as long as

Jan 1, 1899

By S. Mellgren, W. Opie

AN equilibrium state of importance in the process of electrolytically depositing titanium from fused chloride electrolytes is that which exists between titanium metal, titanium dichloride, and titanium trichloride. This can be expressed by the reaction titanium concentration of the solution, temperature, and the proportion of strontium chloride and sodium chloride in the solution. Procedure The general procedure used consisted of the following steps: 1) Development of an analytical method for determining Ti+2 and total titanium. 2) Preparation of batches of fused salt solutions containing various amounts of total titanium, Ti+2 and Ti+3 3) Blending of the prepared batches and excess titanium metal in Vycor tubes and allowing the solutions to come to equilibrium. By blending, solutions with different total titanium content could be prepared and equilibrium could be approached from the high Ti+2 and low Ti+2 sides. 4) Studying the effect of titanium concentration, temperature, and the mole ratio of the solvent chlorides, SrC1, and NaC1, upon the equilibrium.

Jan 1, 1958