Search Documents

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

By Christopher H. Bierbaum

The first significant fact observed in the study of bearing metals is that not a single pure homogeneous metal has given satisfactory service; all bearing metals are alloys made up of two or more phases; that is, they consist of hard and of relatively soft microscopic particles intimately mixed. The function of the hard particles, or bearing crystals, is to support the load and resist the wear when actual metallic contact exists between the bearing surfaces. The functions of the softer particles are to allow the harder particles to adjust themselves to the surface requireinents of the journal and to wear down slightly below the surface of the harder, forming slight depressions on the apparently smooth wearing surface of the bearing, in which some of the lubricant is held when the bearing surfaces are brought into contact with each other. It is this characteristic of certain alloys to form these slight depressions, and thus provide the means for retaining a lubricant, that characterizes them as true bearing metals; in fact, a bearing metal has been defined as "an alloy that is capable of retaining a lubricant upon a bearing surface."' The extent to which the lubricant can be so held determines the most valuable characteristic of an alloy as a bearing metal. An alloy which, perhaps, most characteristically represents a bearing metal is the composition of copper and tin that contains sufficient tin to produce the tin-copper eutectoid, or delta crystal. The depressions worn upon the surfaces of the softer crystals of the teeth of a motor-truck worm wheel, made of an ll-per cent. tin bronze, in many cases were from 5 to 6 microns in depth; all other conditions remaining constant, this depth of wear increases with an increase of working pressure. This copper-tin bronze contains intercrystalline shrinkage cavities, which also

Jan 1, 1923

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By William Wraith

1. INTRODUCTION. AT the Washoe smelter,. Anaconda, Mont., the blister-copper from the converters is transferred, by means of a crane, to a refining-furnace,, in which it is brought to proper pitch by means of air and poles. From this furnace the refined copper, containing gold and silver, is poured into cast-iron molds placed on a platform-conveyor, giving an anode 36.75 in. long, 28 in. wide, and 21 in. thick. By reason of a disagreement between the smelter and the refinery, in reference to the silver-content of the anodes, it became necessary to investigate the methods of sampling used. II. SMELTER METHOD OF SAMPLING. At the smelter the sampling is done by " spotting " into water a small portion of the molten stream of copper as it flows from the furnace, by batting" the stream with a wooden paddle. The first sample is taken 30, min. after the pouring is started, three. other samples being taken at 1-hr. intervals, each sample weighing from 4 to 6 oz. The samples are dried, examined for particle's of burnt wood, screened on a 10-mesh screen of No. 8 wire to remove the fines, the oversize then screened on a 4-mesh screen of No. 20 wire to remove the coarse, the undersize of this screen being taken as the sample. Teh four portions thus obtained are thoroughly mixed and spli in half by passing over a 16-slot splitting-device, slots being 0.5 in. wide. One-half of the sample is sent to the laboratory for analysis and one-half kept as a duplicate. III. REFINERY METHOD OF SAMPLING. The method used at the refinery and also used in this investigation is the one developed by Dr. Edward Seller, of

Mar 1, 1910

By J. L. Brimhall

Slip-line formation during bending has been studied on neutron-irradiated molybdenum single crystals. For equivalent strains, the slip lines are coarse and distinct in the irradiated molybdenum and not resolvable in the unirradiated molybdenum. The slip lines have been directly correlated with dislocation channels present in the irradiated and deformed thin foils. The heterogeneous distribution of the dislocations during deformation in the irradiated material results from dislocation interaction with the dejects produced during irradiation. Impurities , in the form of' carbides, affected the dislocation channeling Principally by acting as dislocation sources. ALTHOUGH the mechanical behavior of irradiated materials has been studied extensively, the precise mechanism of irradiation hardening has not been established. Some information on the microstructural species responsible for hardening of irradiated materials has been derived from direct and indirect observations. The direct observation of the structure of deformed irradiated metals, particularly by transmission electron microscopy, is a relatively new and unexplored area. Slip-line studies in fcc metals have been restricted primarily to copper.1-3 Very coarse slip lines, representing slip on many closely spaced planes, have been observed in deformed, irradiated copper. Coarse slip lines have also been observed in irradiated aluminum.4 Clear channels in irradiated copper caused by dislocation motion through the defect structure have been seen by transmission electron microscopy and correlated with slip lines.5-6 To date, little work has been reported on the irradiated bcc metals. Eyre described the slip lines around hardness indentations on irradiated iron and found them to be more distinct than lines in unirradiated material.' Mastel et al.' have observed channels in deformed irradiated molybdenum similar to those reported in copper. As part of a program concerned with the effect of neutron irradiation on metals, the slip-line

Jan 1, 1965

By K. Thirumalai

Although the term "spalling" has long been known, Norton l first referred to its usage for the fracture or disintegration of materials subjected to rapid temperature changes. Spalling of ceramic materials at high temperatures has received attention in the past.2-4 Removal of the char formed during ablation in reentry of space vehicles has been referred to as mechanical spalling.5 The first experiments to evaluate the process of rock fragmentation by thermal spalling were conducted by Stoces6 using a series of gasoline burners on the quartz veins of the Zinnwald deep mines in Germany. After the development of rocket-jet burners, the principles of thermal spalling combined with high fluid momentum found wide practical application in rocks. The well-known jet piercing process for drilling blastholes in taconite and for jet channeling in the quarrying of granite are among the more notable of these application.7 For the purposes of this study, thermal spalling or spallation of rocks is defined as progressive failure caused by thermal stresses induced by a sudden application of heat from a high temperature heat source. Gray observes that the size of the spall is dependent on the pattern of induced thermal stresses before failure. The spallability or the relative susceptibility of rocks to failure by thermal spalling is a complex but potentially useful parameter for qualitative comparisons. Fundamental differences exist in the degree of spallability among different types of rocks. Accurate prediction of spallability of any particular rock has so far not been possible. Measurement of the state of stress and temperature in the rock during the rapid thermal spalling process poses difficult problems that must be solved. Identifying the parameters that influence the thermal spalling proc-

Jan 1, 1970

By R. R. Sayers

IT has long been common knowledge that workers in anthracite are prone to develop a disabling disease of the lungs. Some of the earliest scientific contributors dealing with anthracosis were: Pearson1, in his report in 1813, on the coloring matter of the bronchial glands and black spots in the lungs; Stratton2, in 1838, who first termed the condition anthracosis; Greenhow3, who reported to the pathological society in 1865, on the Black Lung of the Collier, and Pick4 in 1870, who reported on the chemical composition of the ash of a collier's lungs. Visconti5, in 1870, is accredited with being the first to use the term "silicosis" to denote the pathological condition of the lungs resulting from the inhalation of silica. Rovida6 confirmed the reports of Pick and Visconti in 1871, in his report on a case of silicosis and chemical examination of the lungs for silica content. The relationship of pulmonary infection, as associated with disabling pneumoconiosis affecting the coal miner, has frequently been discussed. While most reports have emphasized the role of infection, there has been some disagreement regarding the prevalence of tuberculosis among those suffering from anthracosis. The report by Wainwright and Nichols7 in 1905 has frequently been cited to show that the incidence of pulmonary tuberculosis among coal miners was -less than that among the general population. It was their opinion that pulmonary tuberculosis was more prevalent among the miners' families than among the miners themselves.. Collis and Gil-christ8, in 1928 in their study of the Effects of Dust upon Coal Trimmers, concluded that among such workers there was an excess of deaths from bronchitis and pneumonia but not from pulmonary tuberculosis. They

Jan 1, 1935

By Arthur F. Taggart, G. R. M. Del Giudice, M. Hassialis, A. M. Saddler

Flotation of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest days of flotation that certain of the nonsulphide nonmetal minerals—e.g., sulphur and graphite—would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation† of certain oxidized minerals, both metalliferous‡ and nonmetalliferous, and separation thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentration, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion. The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material. By using large quantities of oil, it is possible to form substantially air-free oil-bound masses or granules of nonsiliceous minerals and to

Jan 1, 1939

By A. M. Saddler, G. R. M. Del Giudice, Arthur F. Taggart, M. Hassialis

Flotation of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest days of flotation that certain of the nonsulphide nonmetal minerals—e.g., sulphur and graphite—would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation† of certain oxidized minerals, both metalliferous‡ and nonmetalliferous, and separation thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentration, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion. The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material. By using large quantities of oil, it is possible to form substantially air-free oil-bound masses or granules of nonsiliceous minerals and to

Jan 1, 1939

By Joseph E. Pogue

The outstanding features of 1926 in the petroleum industry included the following: 1. Stocks of all oils (crude and refined) were reduced, making the first annual decline since 1918. 2. Domestic crude oil production increased steadily during the last 11 months of the year, accelerating during the fourth quarter, and ending the year at the highest level ever attained. 3. Three new major oil fields were developed—Panhandle, Spindle-top and Seminole. 4. Important advances were registered in production technique, tending to retard the declines of old wells and to maintain the flush periods of new wells. 5. The problem of gaining greater economic control of production through unit operations and gas conservation received growing recognition by the industry and the Federal Oil Conservation Board. 6. The rate of drilling was sharply increased during the second quarter of the year and suffered only a very slight retardation during the closing months. 7. The runs of crude oil to stills were maintained above normal throughout the year and underwent acceleration during the fourth quarter. 8. The gasoline situation was marked by a continuous and substantial increase in the rate of production of cracked gasoline, and by an improvement in the statistical position of the commodity. 9. Prices of both crude petroleum and its principal derivatives were characterized by more profitable levels and greater stability than for a number of years past; and, while showing declines during the fourth quarter, prices did not recede sufficiently to slow down materially either drilling or refinery operations. Change in Stocks The keynote of 1926 was a reduction in stocks of all oils to the extent of approximately 24,000,000 bbl., or 4.4 per cent., of which roundly

Jan 1, 1927

By S. G. Dixit, A. K. Biswas

The flotation and adsorption behavior of ilmenite, monazite and zircon have been studied with sodium oleate as the collector and pH as the principal variable. The maxima in the flotation and adsorption properties of any of the above minerals fall within similar pH ranges. The bell shaped pH versus adsorption magnitude (r) curve is explained on the basis of collector concentration (Co and the concentration of hydroxyl ion (COH-) acting as the depressant. An equation of the type: 1 =KiCor~K2 Coh-/Coi-is proposed to account for the experimental data. The beach sand deposits along the sea coast in Southern India contain ilmenite, monazite, zircon, rutile and sillimanite as valuable minerals while quartz, garnet, shells and traces of hornblende form the gangue. A typical composition of the deposits is reported to be as follows:' Ilmenite 75%, Zircon 4-6%, Rutile 3-4%, Monazite 2 - 4%, Garnet 2 - 5% and the rest 8 -10%. Selective flotation of beach sand constituents has been reported by many workers.2-4 The fatty acid soaps have been invariably used as collectors. It is seen that all the valuable constituents of the beach sand are efficiently floated by soap collectors such as sodium oleate. In order to selectively float the beach sand constituents, it is necessary to use some depressants such as sodium silicate.3 The physicochemical parameters that govern the flotation of these minerals are yet to be studied in detail. In the present article, the findings on the parallel studies on the flotation and adsorption of the systems — ilmenite-sodium oleate, monazite-sodium oleate and zircon-sodium oleate — are being reported. In these correlative studies on adsorption and flotation of beach sand minerals, ilmenite (FeTiO3), monazite (Ce, Dy, Nd) PO4 and zircon (ZrSiO,) have been selected because they represent three important

Jan 1, 1970

By Karl Sundberg

ElectRical investigations carried out in regions containing sedimentary rocks showed that sediments generally are good electrical conductors, a fact which at the present time is used for structural investigations by electrical methods. It is of fundamental importance, not only for these investigations but also for electrical prospecting in general, to know the electrical properties of various soils and rocks. It will be useful, therefore, to discuss this question with the hope that the general points of view discussed in this paper will perhaps be completed by further observations and determinations of material from various localities. This paper is based principally on the study of literature, and the purpose is primarily a discussion of the main factors that determine the electrical conductivity of soils and rocks. It will follow, however, that the factors discussed here also frequently decide how far a certain orebody can be regarded as a good electrical conductor compared with the surrounding rocks. All rocks are more or less porous, and the pores are filled with liquids and gases. Their electrical conductivity, therefore, depends on the following factors: 1. The electrical conductivity of minerals composing the rock. 2. Electrical conductivity of the liquid filling the pores. 3. Proportion of the volume of liquid filling pores of the rocks to the solid rock material. 4. Shape of the pores. 5. Arrangement of the particles of gas and liquids. 6. Temperature. Dry minerals, with the exception of certain ore minerals, are complete nonconductors from the point of view of applied geophysics; in the present investigation we deal with rocks which have no conducting minerals, and factor 1, therefore, is not important. The same is true of soils. The liquids contained in soils and rocks in most cases are waters, sometimes oil. As oil is a nonconductor of electricity, the impregnating waters will determine the electrical conductivity of soils and rocks.

Jan 1, 1932

By F. R. Morral, E. P. Miller

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By E. P. Miller, F. R. Morral

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By John L. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product ; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are: 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct ThO2,*, and the ilmenite 56 1/2 pct TiO2, whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be avail- able in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources. 1 Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations.

Jan 6, 1950

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By José Geraldo Vieira

Companhia Vale do Rio Doce (CVRD), founded in 1942, is located near the town of Itabira, Brazil. Its iron ore deposits include over 500 million metric tons (mt) of high-grade hematite and about 2 billion mt of itabirite (banded rock formed by thin alternate layers of hematite and silica). These deposits are part of the Iron Ore Quadrangle, of which the overall reserves have been estimated at more than 30 billion mt. The magnitude of the project meant difficult early years for the company, including large investments, extensive railroad rehabilitation, and construction of ore port and ore handling facilities. Companhia Vale do Rio Doce was organized as a stock company, and 91% of its shares are presently owned by the Brazilian government. Financing has been accomplished in part through loans from international monetary agencies foreign banks, and foreign industry, as well as Brazilian banks. The company markets mainly abroad. In 1967, it exported 10.6 long tons (It) of ore, principally to West Germany, Japan, Netherlands, Italy, France, United Kingdom, and the United States. The Rio Doce geographic region where CVRD operates is strategically located among the large population centers of Rio de Janeiro, Belo Horizonte, Salvador, and Vitoria (Fig. 1). It covers an area of approximately 81,000 sq km in the states of Minas Gerais and Espirito Santo, and its population in 1968 was about 3.5 million. This region presents excellent prospects for development, with factors favorable for forestry, agriculture, grazing, and exploration for minerals other than iron ore, Electric power (hydroelectric plants) is available, as well as two main systems of transportation: the Rio-Bahia highway and the Vitoria-Minas Railroad. Pioneer activities at Itabira started about 1720 as small gold mining centers. The town is about 80 km northwest of Belo Horizonte and

Jan 1, 1969

By D. Coutsouradis, L. Habraken, P. Nicolaides

The TTT curves of 0.1 pct C, 13 pct Cr steels containing up to 12 pct Co have been determined in order to establish whether the effect of cobalt is similar to that observed m plain carbon steels. It is shown that cobalt increases the incubation time and decreases the transformation rate, though not in an uniform way. The bainitic transfornation is displaced to lower temperature and overlaps partially the martensitic zone. ThE effect of cobalt on the transformation of a plain carbon austenite has been studied by many investi-gators.'-3 It was shown that cobalt displaces the TTT curves to shorter times and diminishes the harden-ability. The interpretations given for this effect of cobalt are conflicting. According to E. Houdremont,4 cobalt increases the transformation rate of austenite because it increases the diffusion of carbon as shown in the experiments of E. Houdremont and H.Schrader,' R.Smoluchowski,5 and M. Blanter.6 On the other hand, M. Hawites and R. Mehl3 deny on the basis of their own experiments any effect of cobalt on the diffusion of carbon and they assume that an explanation should be found in an eventual effect of cobalt on the mechanism of nucleation and growth of pearlite. W. C. Hagel, G. M. Pound, and R. F. Mehl7 have shown by calorimetric measurements that cobalt increases the free energy of the austenite-pearlite transformation in an eutectoid steel and this result explains qualitatively the observed effect of cobalt on the rate of nucleation and growth of pearlite. The purpose of this research was to see by determination of TTT curves, if this same effect exists in 13 pct Cr steels. EXPERIMENTAL PROCEDURES The preparation of the alloys was carried out in an

Jan 1, 1960