Search Documents

By L. P. Teas

Although 1930 has been a year of stagnation, proration and curtailment, the Gulf Coast has measured up to its tradition in the matter of interesting and significant discoveries. Only 2 domes and 7 new structural areas were brought into the producing column in 1930, whereas, in 1929, 13 domes and one structure were added to this list, yet a total of 14 new producing horizons were proved on various domes and structures. On 5 domes new flanks were successfully tested for commercial production. The year 1930 has shown at Barber's Hill that oil in commercial quantities may exist below salt or cap. Numerous wells have been drilled through cap, or even salt itself, into good producing sands. The past year has been particularly notable in the interest and in the number of deep holes drilled. Two wells have gone below 8000 ft. in each of the states of Texas and Louisiana, and in the two states together 14 wells have gone below 7000 ft At the beginning of the year only one well was producing below 6000 ft. in coastal Texas, while at its end, 19 wells were producing or had produced. Geophysical discoveries and activity on the Coast have waned and this type of work has moved further inland. The peaks of production at Pettus, Barber's Hill, Raccoon Bend, Refugio, Orchard and at Humble, in Texas; and at Lake Barre, Port Barre, Black Bayou, White Castle and Vinton in Louisiana, were seen this year. These were new peaks for Humble and Vinton, of course, these fields having previously gone through periods of peak flank production. In Table 1 the completions listed are for the entire month of December in both years. It is remarkable that in 1930, a year of overproduction and proration, there were actually more wildcat operations at its end than at the end of 1929; but it is gratifying that the operations in the proven fields were exactly one-half what they had been at the end of 1929. The price of A grade coastal crude, or oil below 25" Bé., has been cut from $1.30 at the beginning of the year to $1.00 at its close; and B grade, or oil above 25o Bé., has been reduced from a price range of $1.15 to $1.63 down to a range of from $0.75 to $1.22. In spite of these reductions there has been no proration program on the Coast. Systematic

Jan 1, 1931

By E. W. Engle

For several years the Fansteel Products Co. has been engaged in e production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770' C., tungsten 3350' C., and molybdenum 2550" C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum somewhat resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids. The three metals oxidize rapidly when heated at or above a dull red in air. This feature limits their use in many applications where their high melting point and strength make them appear usable. Tungsten and molybdenum, at red heat, are quite inert to hydrogen and nitrogen; while tantalum has a rather remarkable affinity for all the ordinary gases, which results in its becoming embrittled in their presence. This

Jan 1, 1925

By C. H. Mathewson

THIS paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferrous metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties-and this we consider to constitute the elements of metal technology-might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary

Jan 9, 1919

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated' by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By L. W. Kempf, R. S. Archer

The binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.' Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application. Constitution of Alloys Magnesium and silicon combine in aluminum alloys as the compound Mg2Si, which forms a binary system with aluminum. In alloys containing an excess of silicon over that required to form the compound, solidification ends with the freezing at 1022' F. (550' C.) of a ternary eutectic of aluminum, Mg²Si, and silicon. Judging from the horizontal projection of the liquidus surface as given by Hanson and Gayler,² this ternary eut,ectic contains about 13 per cent. silicon and 6 per cent. magnesium. All of the alloys discussed here contain excess silicon, so it

Jan 1, 1931

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC's original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

BASIC open-hearth slags have no obviously unique features when compared with slags from other metallurgical operations. Open-hearth slags form and exist at temperatures ranging from 2500 to 3100 F (1370 to 1700 C). In the course of an open-hearth heat, the liquid slag changes slowly and continuously in chemical analysis-the changes reflecting changes in temperature, changes in metal analysis, solution of charged materials, solution of feed additions, and solution of refractories. Throughout the process, the slag performs specific primary functions that are responsible for a large measure of the technical and economic importance of basic open-hearth steelmaking. It is intended in this chapter to present the chemical reactions by which the primary functions of basic open-hearth slags are carried out, to describe the physical and chemical principles governing the extent to which these reactions proceed and can be regulated, and finally to indicate the limitations imposed on other features of the process by the fulfillment of the primary functions. Basic open-hearth slags perform three primary functions. First and foremost, the slag provides a means of removing phosphorus from the liquid metal. The ability to remove phosphorus is largely responsible for the widespread use of the basic open-hearth process. Second, the slag serves as a controlling factor in transferring the oxygen required for the other oxidizing reactions. Third, the slag provides a means of eliminating some sulfur from the open-hearth bath. While the extent of sulfur removal is not comparable to that of phosphorus, the ability to remove some sulfur contributes much to the value of the process. The effectiveness with which the slag fulfills its functions varies with temperature and composition. Since operating temperatures are fixed largely by the specified nature of the product and the equipment, .the speed and extent to which the functions of the slag are carried out depend largely on its composition. The necessity for regulating slag composition to accomplish the re-

Jan 1, 1964

By A. C. Heath, E. H. Dix

The importance of aluminum-silicon alloys in thc light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and likc silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminurn and alurninum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. Part I.—Aluminum-silicon Alloys The early work on this system was largely confined to determining the general form of thc diagram and in this respect the results are in good agreement. Briefly, alulninunl and silicon form a simple eutectifcrous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Ipraenkell (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solu-t'ion. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility docs not appear

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

By Notman, Arthur

THIS is a day of surpluses, some good and some not so good. One can hardly pick up a newspaper, magazine, review or economic treatise without confronting the fact that we have or are threatened with more .of certain goods than we have use for, whether it be corn, wheat, cotton, coal or oil, -lumber, 'leather, newsprint, automobiles, zinc, lead, copper or what not. How did this unprecedented state of affairs arise? Who is to blame? How shall we avoid smothering ourselves in our own production? The voice of the farmer is raised in appeal to the Government to relieve him from the dilemma of his own fertility. In answer the Government employs thousands of experts and spends millions of dollars to aid the farmer. But to what end? To make him still more efficient so that he may produce even greater surpluses? Not satisfied with the result, it spends other millions to prepare vast areas of the arid land of the West for more farmers to cultivate and insure yet larger surpluses. Then what? Naturally another appeal to the Government to fix prices by financing the

Jan 1, 1928

By N. A. Gokcen

The construction and operation of a simple and accurate vacuum-fusion apparatus are described in detail. Absolute accuracy of the oxygen analysis has been determined by the reduction of oxides weighed to 20.01 mg. The Bureau of Standards steel samples have been analyzed repeatedly, and their inadequacy for the acceptable range of oxygen is presented. The limits of interference of manganese, aluminum, and titanium, and the effects of tin and water-cooling of the furnace tube have been investigated in detail. ANALYSIS by the vacuum-fusion method consists of melting a sample in a degassed graphite crucible under high vacuum and extracting oxygen as carbon monoxide, and nitrogen and hydrogen as gaseous elements. The resulting gas mixture is analyzed for its constituents, from which oxygen, nitrogen, and frequently hydrogen may be determined within 1/2 hr or less. The history and summary of methods1-4 and extensive reviews of literature'.' for the determination of gases in metals have been published in detail. The foundation of the modern vacuum-fusion method of analysis was laid by Jordan and Eckman,11 and Oberhoffer and his associates.1, 10 Diergarten,11, 12 Meyer,13 Thanheiser et al.,14, 15 Ericson and Benedicks,16 Ziegler,17, 18 Sloman,16-23 Thompson et al.,24 and later many others contributed to the improvement, accuracy, and limitations of the method. In some investigations, however, the limitations of the procedure and the errors involved in the analysis require further critical examination and evaluation. In many apparatuses, lunnecessarily complicated and cumbersome features and elaborate precautionary measures do not have conclusive advantages. The purpose of this invest:igation was, therefore, a) to construct a very simple and accurate apparatus, b) to determine the absolute accuracy of results, c) to establish the limits of interference of manganese. aluminum, and titanium, d) to reexamine critically the reduction and recovery of oxygen from oxide powders of various sizes, and e) to evaluate critically the eight steels of the Bureau of Standards."' Apparatus The apparatus used in this investigation is shown in Fig. 1. It has been used for over three years, during which several modifications were made. A brief description of the apparatus is as follows. The transparent silica or Vycor tube, E, is joined to the Pyrex head, B, by mean of a face to face ground joint sealed with mercury. A similarly sealed ball and socket joint would also have been satisfactory. A standard tapered ground joint, successfully used by some investigators, was tried, but in the absence of grease or vacuum cement it was very difficult to disassemble the joint. The graphite crucible, G, 15/16 or l 1/8 in. OD, 2 1/2 or 3 in. high, 1/10 in. wall, shown enlarged in Fig. 3a, is made from the rods containing less than 0.08 pet ash. Two baffles, overlapping sufficiently to prevent spattering, are inserted in two opposite slots cut on a band saw. Two small holes in the baffles permit the temperature measurement of the melt. A second type of crucible, Fig. 2, G, shown enlarged in Fig. 3b, is also satisfactory, though not as convenient as the crucible shown in Fig. 3a. Somewhat similar but more elaborate crucibles with baffles were first tried by Ericson and Benedicks,'" but were abandoned in favor of a crucible with a stopper and a peripheral graphite powder filter. Various versions of their crucible with a stopper have later been used by other analysts, 10-27, 27-30 The crucible is packed directly in E, Figs. 1 and 2, with —35 + 48 graphite powder for shielding and insulation. A minimum layer of 7 mm of powder is necessary for keeping E cool and minimizing the blank. The first use of graphite powder was made by Sloman,10-23 Who found that —200 mesh was the most satisfactory. The author tried various size powders from +20 to —100 mesh and found that a) particles of 28 mesh or larger were not sufficiently insulating and were heated by the induction current, b) the powder finer than 60 mesh packed too much and did not readily permit the escape of gases even when the crucible was heated very slowly; hence, the powder was occasionally blown out of the side in the crucible and in the mercury pump. The optimum size powder is, therefore, 35 to 48 mesh size or 0.4 mm in average diameter. The furnace is designed to eliminate excessive amounts of

Jan 1, 1959

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy). Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

Jan 1, 1887

By Castle. J. E., J. L. Gillson

In this chapter there is a wide difference in the meaning of some words used for rock and mineral names as defined by scientists and tabulated in the "Glossary of Geology and Related Sciences," published in 1957 by the American Geological Institute, and the meaning as used by the commercial producers of feldspar. It is necessary, therefore, to define these terms giving both the "scientific" and the "practical" definitions. There is no ambiguity about the name feldspar itself. This is a general term for a group of related minerals which are silicates of aluminum, combined with sodium, potassium and calcium. The feldspars are the most abundant minerals of the igneous rocks, and since these rocks make up the largest proportion of the earth's crust by volume (although not of the actual surface area of the continental land masses) the feldspars are the most abundant minerals of all. The igneous rocks themselves are classified on the basis of the variety of the feldspar present. The potash feldspars, which are called orthoclase and microcline, are the dominant minerals of the granites and syenites, and of their fine grained equivalents, the rhyolites and trachites. The plagioclase feldspars form an isomorphic series, of which the sodic endmember is called albite, and the lime endmember, anorthite. The members near the sodic end, albite, oligoclase and andesine are the characteristic feldspars of the granodiorites and diorites, and of their fine grained equivalents, the dacites, and andesites. These feldspars-orthoclase, microcline, albite oligoclase and andesine-are the feldspars used commercially. Labradorite, a member of the plagioclase group, in which the lime exceeds the soda in the chemical composition, is the common feldspar of the gabbros, anorthosites, norites, basalts and other so-called "basic" rocks. Although some attempts have been made to use labradorite as a commercial feldspar, none is now used except as an ornamental stone. The mineral anorthite is very rare. Since the feldspar in most of the common igneous rocks is relatively fine grained, and mixed intimately with other minerals, from which it can be separated cleanly only with difficulty, most masses of the common rocks cannot be used as sources for the feldspar contained in them. It is only the rarer types of rocks in which the feldspar is very coarse-grained, or ones containing very little of the iron-bearing minerals which are objectionable impurities in commercial feldspar, that are quarried to yield an acceptable product. The most widespread type of such a rock from which commercial feldspar can be produced, is that called "pegmatite." These rocks are dikes and bodies of irregular shape and of a size measured in feet or yards in most cases, rather than in miles. They are more commonly associated with granites, rather than with other coarse-grained igneous rocks. Many of them contain crystals of various minerals, including the feldspars, that are much larger than are found in the host rock, the granite, and in many there are large masses of feldspar that are sufficiently free from iron-bearing silicates so that products acceptable to the ceramic industry can be produced, in some cases simply by hand sorting. Most of this feldspar in pegmatites, however, does contain intergrown quartz up to 25 pct. Pegmatites are so important, not only as commercial sources of feldspar, but also of other minerals which are produced com-

Jan 1, 1960

By James Aston

A proper consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. Manufacture of Wrought Iron The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By H. P. Allen

THE chloridizing mill of the Standard Reduction Co. is located about 75 miles south of Salt Lake City on the Tintic branch of the Denver & Rio Grande Western R. R. and 12 miles from the Tintic Standard mine. The daily capacity is 200 tons of a siliceous, low-grade, silver-lead ore from this property. It has operated continuously since it was started in January, 1921. The process consists essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid, the precipitation of silver on sponge copper and of copper and lead on tin-plate cuttings. The precipitates are shipped to a smelter. Some of the general ideas involved are said to have been used by Augustin in England, in 1840. A number of textbooks treat of the subject, especially the chloridizing roast followed by a leach with sodium hyposulfite or amalgamation. The process was revived in this district by Theo. P. Holt, N. C. Christensen, the Bureau of Mines, and others.

Jan 8, 1925

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957