Search Documents

By W. A. Wood, W. H. Reimann, Maria Ronay

The basic mechanism of fatigue is studied in annealed a brass subjectecl to alternating torsion at room temperature, 100°, 200°, 300°, and 400°C, and in air. It is shown that the slip-zone micro-cracking which characterizes fatigue damage produced by small amplitudes at room temperature is progressively replaced by grain boundary cracking at elevated temperatures, replacement being complete at 400°C. Replacement occurs not because slip activity decreases hut because slip movements at elevated temperatures cease to concentrate in narrow zones and instead disperse. Decrease of amplitude at 400°C through permitting longer lives of specimens before fracture actually causes in- MOST studies of fatigue at elevated temperature have been concerned with data for design. Observations on the basic mechanism of fatigue have been largely incidental, though they have led to the interesting inference that this mechanism has features in common with that of creep.' This paper is concerned primarily with the mechanism itself. Advantage has been taken of mater- crease in pain boundary damage, an anomaly attributed to the greater difficulty at elevated tempwature of starting and propagating a crack. Surface corrosion was most pronounced along slip bands but since at elevated temperatures the slip hands showed no cracking the surface corrosion did not appear to influence onset and early spread of fatigue damage. Similarly the type of fatigue damage produced at room temperature by cyclic strain at large amplitudes, characterized by irregular mi-crocracks at zones between disoriented regions in a grain, was also replaced by mainly grain boundary cracking at elevated temperature, though not so completely. ials and procedures known to show readily how fatigue affects the microstructure of a metal at room temperature, so that direct comparison might be made with what the same procedures show when the material is subjected to fatigue deformation at higher temperatures. 1) MATERIAL This was 70/30 a brass, used extensively in previous studies at room temperature.' Specimens were turned from extruded rod to have parallel test portions 1-1/4 in. long and 7/32 in. diameter, annealed to a grain size -1/10 mm, and electro-

Jan 1, 1965

By Andrew W. Jenike

STORAGE AND FLOW Introduction The layout and design of a bin or stockpile for bulk solids should assure reliable feed at the required time and rate without spillage and, when required, without segregation and degradation. The typical procedure in the design for gravity flow follows these steps: 1. The bulk solids to be stored are identified and the range of moisture content, temperature, feed rate and time of storage at rest, as well as the storage capacity, are specified. The materials of construction of the hopper, that is of the converging part of the bin, are decided upon. Hopper liners and coatings to reduce wall friction are considered. 2. The flow properties of the bulk solids and the friction angles against the wall materials are measured for the expected range of conditions. 3. The width of a slot outlet needed for reliable flow of each solid under the full range of conditions is determined from the tests. This dimension is an explicit measure of flowability of a solid. The widest slot determines the critical solid and the critical conditions. 4. A suitable feeder of size sufficient for the widest slot outlet is selected. 5. On the basis of the measured wall friction angles, a suitable wall material is selected and a mass flow hopper is designed to ensure reliable and uniform flow of solid into the feeder and to minimize the load on the feeder. The mass flow hopper may extend upward to the intersection with the cylinder thus producing a mass flow bin. Alternatively, the hopper may terminate at a height equal to a few widths of the outlet and then expand at a less steep slope in its upper part in order to save headroom, or it may terminate in the flat bottom of a bin or stockpile. The choice depends on the flow properties of the solids and the size of the bin or stockpile. 6. The design of the bin is completed for the specified storage capacity. Multiple hoppers and

Jan 1, 1982

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By A. J. Kesterton

MORE than 90 pct of the total tonnage of ingots made at Abbey Melting Shop is for steel sheet to specifications ranging between 0.055 and 0.07 pct maximum carbon. Since the rate of carbon elimination in the open hearth declines considerably as the carbon approaches these low levels, the use of oxygen for this purpose constituted a profitable field for development, particularly to increase ingot output. Development Several experiments were carried out initially in which water-cooled guns, originally of all-steel construction and later with fabricated copper heads, were introduced manually through a hole in the back wall of one of the 225 net ton furnaces, the oxygen being delivered about 4 to 6 in. above the slag. Successful blows were obtained, but manipulation of the gun was cumbersome. Application through the charging doors by means of bare steel lances was considered but rejected, because much of the scrap was light, necessitating a large number of buggies per charge, and consequent long occupation of the track in front of the furnaces by buggies. To construct an efficient mechanism it was decided to experiment with the introduction of the gun through a hole in the roof. This was eventually successfully achieved, with the following advantages. 1) The actual mechanism required is simplified, and can easily be remotely controlled. 2) No large steel framework projects out over the back platform, possibly interfering with tapping, and there is no danger of damage by casting cranes. 3) The railway track in front of the furnaces is left entirely clear for the passage of scrap buggies, eliminating interference with adjacent furnaces charging. 4) As compared with the use of bare steel lances, a water-cooled jet eliminates the manpower required to handle, control and change the bare pipes. 5) A jet through the roof can be situated over the center of the bath so that, whatever the direc-

Jan 1, 1958

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

The early records of coal in Kentucky by Walker and Gist have already been mentioned. Thomas Hutchins was aware of it in 1778, or perhaps several years earlier, as in writing of the Buffaloe, now Green, River, he said, "several persons who have ascended this River, say, that Salt Springs, Coal, Lime and Free Stone etc. are to be found in a variety of places."1 The next record found is an entry to Ellis and Marshall, of 878 acres on Coal Bank Creek, in the, then Fayette County on July 14, 1784.2 The settlement might have been made, or the name given, some time before. Hermeline, in 1783, mentioned iron ore and coal on the Green River,' although he had not been west of the Susquehanna River; his knowledge of coal might have come from Hutchins, although the latter made no mention of iron in that locality. In November 1790, coal was mined on Sturgeon's Creek in Lee County and floated in three barges down the Kentucky River to Cleveland's Ferry, where it was hauled to Lexington. The results were not equal to the expectations, and it was 1793 before the experiment was. repeated 4 In 1791, the estate of Samuel Wharton advertised for sale 31,000 acres "in the county of Jefferson, on the North Side of the Green or Buffaloe river, in the State of Virginia."5 In November 1795 three patents were issued for land in the then Lee County, aggregating 130,000 acres. These patents cover much of Harlan County. The descriptions of these surveys mention passing stone coal. on Rough Branch of Martin's Fork, a "great deal of stone coal" on Blacksnake Branch of Pucketts Creek, and "a quantity of stone coal" probably on Crummies Creek.6 Jedediah Morse, in The American Gazetteer, 1798, said that in Kentucky "in many places there are appearances of potter's clay, and coal in abundance." It is possible that shipments may have been made from near

Jan 1, 1942

By Walter E. Duncan, Oscar F. Tangel, A. M. Gaudin, Franklin Dewey, R. A. Johnson

Xanthates have been used as collectors of sulfide minerals in the concentration of ores by flotation for over a decade, yet much remains to be done to elucidate the underlying reasons for the remarkable effectiveness of these compounds in this connection. Briefly stated, the known facts concerning the effect of these reagents on the floatability of minerals are as follows: 1. Xanthates are without effect on silicates, silica, and generally on minerals currently regarded as "gangues." 2. Xanthates in very small amount increase enormously the floatability of sulfides of copper, lead, silver, iron and mercury. 3. If zinc sulfides are first '(activated," as by treatment with a copper salt, they are readily floated by xanthates; otherwise not. 4. Elemental copper, silver and gold have their floatabilities increased by xanthates. 5. Sulfides of elements that are not typically metallic—e.g., stibnite, realgar, molybdenit—are not made to float markedly better by treatment with xanthates. 6. Oxidized minerals of lead and copper are floated if treated with large amounts of xanthates, but not so if treated with amounts of the same order of magnitude as required for sulfide flotation. Oxidized zinc minerals are not floated unless xanthates having unusually long hydrocarbon chains (e.g., eight carbon atoms or more) are used. Iron oxides and carbonate are not floated by xanthates. From a flotation standpoint the most striking feature about xanthates is the very small amount required to accomplish startling changes in the behavior of some minerals. The amounts used in practice to effect excellent concentration are frequently of the order of 0.05 lb, of agent per ton of ore; that is, of the order of one part of agent per forty thousand parts of ore. Changes in amount of agent of the order of 0.01 lb. per ton of ore (or 0.002 lb. per ton of pulp, on a 4:l basis) have marked effects on the metallurgical results obtained. Yet these changes represent a variation of but one part per million parts of pulp.

Jan 1, 1935

By David Cole

At the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that time impending. The simplified flow sheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.l The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopy-rite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow ,would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) the very fine sand, and especially the very fine but still granular sulphide particles, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrassment, the increase of capacity required. For reasons that are obvious, this kind of feed preparation for the slime could not be successfully accomplished in any form of pointed boxes or

Jan 1, 1917

By Samuel Hoyt

This paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by vow Gomperz,l was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disc floats on the melt, and is provided with a central hole about 1 min. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started. The capillary brings up a small quantity of molten metal with it to a point just above the lava disc. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a -small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

By Charles H. MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat,, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now " potash " has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks. It has been found that the amount of potash remaining in decomposed rocks is not the same as that in the original rock. For instance, granite containing originally 5.58 per cent. potash contained only 1.49 per cent, in the decomposed rock. Syenite containing 6 per cent. in the original

Jan 1, 1915

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By R. G. Webber, F. C. Langenberg

During the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point. The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the bars was tested in this manner and in no instance could any difference in structure in the three specimens1 be detected. Bars 1 to 3 inclusive are pearlitic in structure. The white areas are ferrite (iron with certain impurities in solution) and the dark areas pearl-

Jan 1, 1915

By Major N. R. Junner

Although manganese-garnets are rarely seen in hand specimens of the manganese ores and associated rocks, they have been detected by the writer in thin sections of all the ores and wall rocks that have been sliced, with the single exception of the Insuta deposit. Rhodonite, and an almost colorless amphibole, which appears to be manganiferous, are less common. Types of Occurrence (a) Rocks Composed of Manganese-garnet and Quartz The best known examples of this type are from near Bole and Wa in the Northern Territories of the Gold Coast, and from near Chama in the Gold Coast Colony. Normally these are fine and even-grained rocks, in which the garnets cannot be recognized in hand specimens. They are often stained with secondary manganese oxide. Thin sections examined microscopically are seen to be composed of aggregates of minute crystals of garnet in a matrix of mosaic quartz. Some manganese oxide and braumite (?) is often present, but other minerals are exceptional. The relative proportions of garnet and quartz in these rocks vary greatly and there is a complete gradation from quartz-rock to garnet-rock. (6) Rocks Composed Mainly of Manganese-garnet and Manganese Oxides Rocks of this type are known from Kalimbi Hill near Siripe, Pabini Hill near Bangwon, near Odumase and Konongo, and in the Ya Ya creek, about 5 miles east of Dunkwa. These are usually fine-grained banded dark-colored rocks, composed of abundant minute garnets in a matrix of black manganese oxide and braunite (?). A little microcrystalline is often present, and occasionally a little colorless amphibole. quartz (c) Rocks Composed of Rhodonite and Manganese-garnet Rocks of this type are not common. They are known from near Chama, and from the road between Senyong and Mangkuma. Some quartz is usually present. All these rocks resemble closely in texture and composition certain rocks from India, described by Fermorl as "gondite;" and they also resemble certain rocks described by Derby2 from the Queluz district,

Jan 1, 1927

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By W. J. Keep

Manganese is a nearly white metal, having about the same appearance when fractured as white cast-iron. Its specific gravity is about 8, while that of white cast-iron, reasonably free from impurities, is but a little above 7.5. As produced commercially, it is combined with iron, and with small percentages of silicon, phosphorus, and sulphur. It is generally produced in the blast-furnace. If the silicon is under 0.50 per cent., the product will be white. If the manganese is under 40 per cent., with the remainder mostly iron, and silicon not high enough to make the product gray, the alloy is called spiegeleisen, and the fracture will show flat reflecting surfaces, from which it takes its name. With manganese above 50 per cent., the iron alloy is called ferromanganese. As manganese increases beyond 50 per cent., the mass cracks in cooling, and when it approaches 98 per cent. the mass crumbles or falls in small pieces. When the percentage of manganese is high, the planes of the fracture are not so bright as when it is lower. The ferro-manganese which we have used in the experiments reported in this paper, contains Mn, 81.62; Si, 0.256 ; and combined carbon, 6.153 per cent. We have not been able to make test-bars from this, because the alloy cracks in small pieces in cooling. Manganese combines with iron in almost any proportion, but if an iron containing manganese is remelted, more or less of the manganese will escape by volatilization, and by oxidation with other elements present in the iron. If sulphur be present, some of the manganese will be likely to unite with it and escape, thus reducing the amount of both elements in the casting. Hence, in remelting irons, some of the sulphur which has entered from the fuel with which the iron is melted will very likely unite with some of the manganese in irons which make up the mixture and escape. Remelting, therefore,' reduces the percentage of manganese in cast-iron.

Jan 1, 1892

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944