Search Documents

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one senice hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown. THE property of Kerr-Addison Gold Mines is located in the Larder Lake district of Ontario about 3 miles from the Quebec boundary on the highway between Kirkland Lake and Noranda. It is roughly 320 miles due north of Toronto and 365 miles north of Buffalo, N. Y. The property was staked in 1906 and after several development efforts finally came into continuous production at 500 tons per day in 1937. In 1939 the daily tonnage -was increased to 1200 and in 1941 to 2100 tons. At the end of the war, because of the shortage of labor, tonnage was down to 1100 tons per day, rising to 2200 in February 1947. A further plant expansion inaugurated in 1946 was completed by December 1948, bringing the capacity of the mine and mill to a production rate of 4000 tons per day. Current production, with 880 men employed, is 4400 tons per day. Changes in mining methods and equipment, required by the recently completed expansion program, have yielded interesting comparative results, some of which are described in this paper. Hoisting of ore and waste from the mine, as well as all service facilities for handling men and supplies underground, are provided for in a single vertical five-compartment shaft. Ore and waste are hoisted in 12½-ton skips in balance by a 14-ft diam hoist with drums 115 in. wide, grooved for 2?-in. wire ropes. This hoist, with a total rope pull of 85,000 lb, was designed to operate at a speed of 2600 ft per min to a depth of 4000 ft, hoisting 15 tons of ore in each skip. It is amplidyne-controlled and powered with dual drive dc motors of 2250-hp each, through flexible couplings to two pinion shafts, one on each side of the main gear. Each motor has a peak load rating of 4500-hp at point of greatest duty. Direct current power to the hoist motors is supplied from a motor generator set consisting of a 5000-hp synchronous motor driving two 1750-kw dc generators. The loading pockets used so far are at depths of 1500 and 2725 ft respectively. Consequently the present hoisting speed is 2000 ft per min and the skips capacity only 12½ tons. Now that the shaft has been deepened the new pockets at 3934 ft will be increasingly used so that the speed and the skip size will be increased up to original specifications as required. Some difficulty in meeting the required hoisting cycle is expected because of the shape of the skips. As now in use the cross-sectional dimensions of the inside of the skip are 4 ft 6 in. x 3 ft 8 in. To hold 121/2 tons, therefore, they are 14 ft 10 in. deep. Since the skips are the conventional overturning or Kim-berley type, considerable hoisting time is lost in retardation in entering the headframe dump and in acceleration when leaving. It is expected that to obtain the specified tonnage from this hoist when the skip size is increased to 15 tons it may be necessary to resort to bottom dump skips. This type of skip could reduce considerably the present excessive acceleration and retardation times. Analyses of the skip-hoisting operation are made monthly, and every effort is made to reduce controllable delays. For a nine-month period in 1951 such an analysis shows that the hoist was in operation 92.5 pct of the available time, which was allotted as shown in Table I. Overall hoisting costs, cage and skip, for the year 1951, averaged $0.168 per ton of ore milled. The mine is serviced entirely by means of a single cage, capacity 35 men or 15,700 lb, operating in con-

Jan 1, 1954

By C. E. Lundin, D. T. Klodt

The binary alloy systems, Y-Ti, Y-Zr, and Y-Hf, have been investigated throughout their entire composition regions. There is no compound formation in any of the systems, and each system is characterized by a single eutectic reaction. The eutectic compositions and temperatures are as follows: A eutectoid reaction pct Y and 870°C occurs in the Y-Ti system, whereas a peritectoid reaction,: pct Y and 880°C occurs in the Y-Zr system. Peri-tectic-type reactions at temperatures above the eutectic levels are postulated for the yttrium and hafnium transfovmations. The development of the technology of yttrium has been given considerable attention during the past few years, and studies of binary phase equilibria have, of course, taken a prominent position in this development. In many respects yttrium, in the third group of metals of the periodic table, is similar to the adjacent group of metals, titanium, zirconium, and hafnium, and the knowledge of the phase relationships of yttrium with these metals is basic to their technology. MATERIALS AND EXPERIMENTAL PROCEDURES Materials. The metals for this investigation were supplied by the General Electric Co., Aircraft Nuclear Propulsion Department. The yttrium was in the form of an arc-melted ingot, and the other metals were in the form of high-purity, iodide-Process crystal bar. Table I lists the purities of these materials. Alloy Preparation. Melting was done by conventional techniques in a nonconsumable electrode arc furnace in an atmosphere of purified argon. Melting conditions for each binary system were the same. Each alloy button was inverted and remelted several times to assure homogeneity. Accurate weights of the charges and resultant alloy buttons were obtained to indicate deviations from intended compositions. No chemical analyses were obtained since melting weight losses were consistently in the range of 0.1 to 0.2 pct of the total weight. 10- or 20-g buttons for each 5.0 wt pct composition increment were melted to survey the three individual alloy systems. Additional alloys differing in composition by 1.0 or 0.1 wt pct increments were also melted to study selected regions of the systems. Metallograpllic Techniques. Standard metallo-graphic techniques were followed for mounting and rough grinding. Preliminary polishing was accomplished using 6-u diamond paste as an abrasive on a Metcloth Lap. Final polishing was done on a Microcloth-covered wheel using 1-u diamond abrasive paste. Purified kerosene was used as a lubricant for both polishing stages. • sothermal- Annealing. Alloys were sectioned for as-cast structlure examinations and then homogenized in preparation for isothermal-annealing treatments. Homo{:enization was accomplished by cold pressing the alloy buttons followed by 72-hr anneals at 1100c. The alloys were encapsulated in Vycor or quartz for the homogenization treatments or for isothermal anneals. Resistance-wound or resistance-element tube furnaces were used for the annealing treatments. The homogenized alloy buttons were cold rolled until cracking occurred or until a -in. specimen thickness was obtained. Small -in. square) specimens for the isothermal anneals were then sawed from the alloys. Each specimen was wrapped in tantalum foil before being sealed in the capsule. Temperatures during the anneals were controlled The time at temperature necessary to equilibrate the structures during the anneals was determined for each alloy system by holding triplicate specimens of alloys at a constant temperature for three different periotls. The specimens were quenched and examined microscopically to determine the number and amounts of phases present in the micro-structure as a function of time. Melting Studies. Eutectic temperatures of the three alloy systems were established from the results of incipient-melting studies conducted on as-cast alloys. Specimens to be melted were suspended on a tungsten wire inside a graphite cylinder placed in a glass vacuum chamber. An optical pyrometer was used to follow the temperature of the specimen as it was inductively heated in a high vacuum. The temperatures were corrected for emissivity losses by standardizing the pyrometer with known-melting-point metals. Accuracy of the temperature measurements is estimated to be + 10°C. The melting point of the yttrium was determined to be 1550°C by this technique. The invariant-temperature levels were also checked by an anneal-quench technique. This technique consists of annealing a series of

Jan 1, 1962

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during. the period May 10 to June 10, 1915: Robert M. Keeney, Somersville, Conn. C. A. Moffett, Birmingham, Ala. Emilio Mosonyi, San Salvador, C. A: A. W. G. Wilson, Ottawa, Canada. Junjiro Nagazumi, Fukuoka, Japan. G. H. Glover, Jr., Short Hills, N. J. Francis R. Pyne, Elizabeth, N. J. R. W. Brock, Vancouver, B. C. F. C. Alsdorf, Los Angeles, Cal. J. L. W. Birkinbine, Philadelphia, Pa. W. J. Loring, London, England. Roy H. Allen, Jamesburg, N. J. R. A. Bull, Granite City; 111. Francis Andrew Thomson received the degree of Master of Science from the Colorado School of Mines at the recent commencement exercises. The subject of his thesis was Stamp Milling and Cyaniding.

Jan 7, 1915

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,1 see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in California, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War II. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eightman crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on.2 Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1952

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth's crust.

Jan 5, 1974

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from '0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962

By William H. Spice

Exploratory drilling in South Central Texas for the year 1944 showed a marked increase over that of 1943 and resulted in a similar increase in new fields discovered. In this area, which comprises the 30 counties included in district No. I, Oil and Gas Division, Railroad Commission of Texas,? 61 exploratory wells were drilled during 1944 as compared with 29 exploratory wells drilled during 1943, or an increase of over 100 per cent. Three new oil fields, two new gas fields and one gas-distillate field were discovered during the year, as compared with one new oil field and one new gas field discovered during 1943. These new fields were the result of exploratory drilling throughout the district along the Wilcox trend and the deeper Edwards lime trend, which was started during the previous year. The Wilcox trend yielded the new Loma iilta-Wilcox oil field and the San Caja gas-* tlistillate field, both in McMullen County. The Charlotte field, in Atascosa County, was discovered along the deeper Edwards lime trend. These three discoveries were of considerable importance and subsequent development should indicate the desirability of continued exploration along these trends. The other three discoveries, United oil field in Guadalupe County, Pederson gas field in Milam County and Van Cleve gas field in Zavalla County, were of minor importance. Charlotte Field, Atascosa County, was discovered by the Humble Oil and Refining Company's No. 3 Pruitt, completcd on Aug. 9, 1944, flowing 176 bbl. per day, 3/16-in. choke, 710 lb. tubing, 475 lb. casing pressures, 37.7º A.P.I. gravity, from the top of the Edwards lime from 6917 to 6923 ft. Two oil wells were completed during the year in this field. This discovery is 14 miles southwest of the same company's Imogene field, also producing from the Edwards lime but with considerable difference in reservoir characteristics. The discovery of this field is the result of surface geology and subsequent seismograph survey of the area. Loma Alta-Wilcox Field, McMullen County, was discovered by the Atlantic Refining Company's No. I Atkinson, completed on June I, 1944, flowing 102 bbl. per day, 9/64-in. choke, 1900 lb. tubing pressure, 37º A.P.I. gravity, from Wilcox sand from 6866 to 6869 ft. after being drilled to a total depth of 7185 ft. This discovery is the result of subsurface geology and an extensive seismograph survey of the entire area. Sun Caja Field, McMullen County, was discovered by Edwin M. Jones No. 2-C Ezzell, completed on June 2, 1944 as a dual completion in the Wilcox sands, flowing 1,740,000 cu. ft. gas with 53 bbl. distillate, 1/4-in. choke, 2035 lb. tubing pressure, 53.2º A.P.I. gravity, from sand 6416 to 6453 ft. and flowing 2,000,000 cu. ft. of gas with 127 bbl. distillate, 1/4-in. choke, 2500 lb. tubing pressure, 50º A.P.I. gravity, from sand 6889 to 6916 ft., after being drilled to a total depth of 7264 ft. Three gas-distillate wells were completed during

Jan 1, 1945

By John G. Hall

The unstable metal market during 1949, with resulting lower metal prices, has focused every mine operator's attention on the problem of reducing operating costs. Improvement in mining, methods, use of modern mechanical mining equipment, and increasing the efficiency of the labor force are the tools with which we will have to work. Careful planning is necessary to coordinate all phases so that no one phase is overdone. A mine may become over-mechanized if, for instance, capital charges against new equipment exceed the savings in labor costs, or where a large enough tonnage is not produced. The cooperation, of labor is essential to any mechanization program. There have been too many instances where mechanization and improvements have done nothing more than make up for a decrease in labor efficiency, thus bringing the production of labor back to its old standard. The operator has gained little and labor has gained only a "softer job." In any mechanization program there are gains to be had by both the operator and labor. By the efficient application of modern equipment and improved mining methods the operator should gain by decreased costs, and labor may profit by receiving a share of these decreased costs.

Jan 1, 1950

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By H. W. Reinhardt, J. W. Dally

A dynamic photoelastic analysis of stress waves interacting with a free surface is described. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb N,). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. The mechanics of rock breakage by means of explosives has received considerable treatment by many investigators including Duvall, Obert, Broberg, Rinehart, and Langefors1-11 over the past two decades. Indeed in more recent years several texts12-15 have been written on the topic, treating a wide variety of subjects which are logically related to the modern technique of rock blasting. In rock blasting the chemical energy of a concentrated explosive contained in a relatively small diameter borehole is utilized to fragment the rock. The explosive is transformed into a gas with enormous pressures which exceed 10-5 bars18 This high pressure shatters the rock in the area adjacent to the borehole and produces dilatational and distortional stress waves which propagate radially away from the borehole. The state of stress associated with these outgoing waves produces a system of cracks which extend for a few feet from the borehole. The breakage produced in this manner is limited as the dynamic stress in the pulse attenuates markedly with distance. In the absence of a free surface, the stress wave propagates away from the source without further fracture. With a free face of rock near the drill hole, another mode of breakage occurs which is due to scabbing failure of the layer of rock adjacent to the free face. These scabbing failures are produced by the reflection of the incident waves and the conversion of compressive stresses into tensile stresses sufficiently large to fracture the rock. The detailed nature of the interaction of the stress waves with the free surface is complex and difficult to treat analytically. However, dynamic photoelasticity offers an experimental approach which gives a fullfield visual display of propagating stress waves and the reflection process. Applications of static photoelasticity to solution of problems related to mining technology have become relatively common (see, for instance, Refs. 17 and 18) with a plastic model loaded to produce a state of stress representative of that occurring in the workings of a mine. The application of dynamic photoelasticity is ex tremely limited. Tandanand and Hartman19 have used a multiple spark camera to study fracture in glass and plastic plates impacted by a chisel-shaped tool. This paper describes a dynamic photoelastic analysis of stress waves interacting with a free surface. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb-N6). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. Experimental Procedure The model illustrated in [Fig. 1] was fabricated from a sheet of Columbia Resin CR-39 to represent a bench with a fixed bottom. Properties of the CR-39 pertaining to these dynamic experiments are listed in [Table 1]. Scribe lines on 1-in. centers are used to identify locations along the bench face. The bench height was 8 in., the burden was 3 in., and the overall dimensions of the sheet, 16 and 18 in., were large enough to eliminate reflections from nonessential boundaries during the period of observation of the dynamic event. To simulate a charge in a borehole, a groove 0.062 in. wide and 0.080 in. deep groove was cut into the sheet from one side. The lower end of the groove was 1 in. or 1/3 the burden distance below the bottom of the bench. The upper end of the groove was 3 in. or one times the burden distance below the upper level of the bench. The groove was packed with 60 mg of Pb No per in. of length, and ignited with a bridge wire detonator. Four different ignition procedures were used to examine the effects of detonation direction on the stress wave interaction with the free face of the bench. In Test 1 the line charge was ignited at the top and the line charge detonated downward. In Test 2 the line charge was ignited at the bottom and the charge burned upward. In Test 3 the charge was ignited in the center with the top half burning upward and the bottom half burning downward. Finally in Test 4 the line charge was ignited at both ends simultaneously. Sixteen high-speed photographs of the photoelastic fringe patterns representing the stress wave propagation were recorded for each of the tests. A Cranz-Schardin multiple spark gap camera 20,21 was operated at framing rates which were systematically varied from 110,000 to 250,000 frames per sec during each test.

Jan 1, 1972

By E. L. Jr. Spain

This study was undertaken primarily to determine the reasons for certain varia-tions in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates it some cases exhibited marked differences in specific gravity, crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents.

Jan 1, 1937

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-', a lo-'-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10' cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell's law that where = critical angle, n - index of refraction of air, n' - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,' and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert's law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By W. H. Holman, J. B. Wagstaff

IN spite of considerable interest among blast furnace operators on the question of the penetration of air into the furnace, there is still uncertainty as to how far the blast does, in fact, penetrate. Moreover, it is not always clear just what is meant by the word penetration in this sense. In 1952, Elliott et al.1 showed that at the end of each tuyere of a blast furnace there is more or less of a void. In this region, coke particles are blown around by the force of the air. This explained the well-known observation reported by Sweetser2 hat if a bar is pushed into a furnace through a tuyere it will go easily into the furnace a distance of some

Jan 1, 1958

By Charles A. Chase

This paper, descriptive of a single mine, is presented in the belief that it may furnish useful suggestions to mine-managers encountering similar problems; and it includes the details which will enable them to estimate the value of the methods employed—especially where these depart from common practice. Tt should be added, however, that this mine is not typical of the San Juan district, but differs markedly from neighboring mines in physical conditions and metallurgical requirements. The Liberty Bell mine is situated in San Miguel county, Colo., on the west front of the San Juan mountains, 2 miles north of Telluride. The vein was discovered in 1876 by Wm. L. Cornett, who, with subsequeilt locators, took up claims along the apex. A few hundred feet of development-work was accomplished, and a few? tons of ore were smelted or milled; but profitable working proved impossible under existing

Jan 1, 1912

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company's underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905

By T. Okubo

Gold is generally recovered from silver anode slime by electrolysis in the final step of the copper anode slime treatment. In the present investigation, rapid and direct hydrometallurgical separation and recovery of gold in the early step of the process is studied. Gold is recovered just after the elimination of copper and selenium from copper anode slime. The studied process consists of: (a) oxidizing roasting for selenium elimination, (b) sulfuric acid leaching of the calcine for copper removal, reduction of gold in the liquor by the use of proper reductant such as hydrogen peroxide (production of gold powder), (el nitric acid treatment of gold powder for further purification and (f) melting and casting of gold. Laboratory and miniplant testwork showed that the extraction ratio of gold by chlorine leaching was 99 % up and four nine gold ingot could be recovered without electrolyses.

Jan 1, 1984