Search Documents

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By Patricia J. Rand, Kailish Narayan

Atlantic Richfield Co. began operating a commercial uranium solution mining project in April 1975, in Live Oak County, Tex., 10 miles southwest of the town of George West. The operation is designed to produce 250,00 lb of U308 per year and is jointly owned by Atlantic Richfield Co., Dalco, and U.S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural cattle ranching and farming---but several producing gas fields are present in the areas as well. A nine month enviromental baseline study was conducted on the property beginning in Feb. 1975. Plants and animals of the Clay West area were identified and representative terrestrial and aquatic communities were analyzed. Physical and chemical parameters of the soils were described and analyzed. The surface and underground waters were analyzed chemically; radionuclides, heavy metals, nutrients, and pesticide concentrations were measured in the creek sediments; bacteriological measurements were made in creek water and sediments; radionuclide and chemical levels in plants and animals, both terrestial and aquatic, were measured. These studies, though not required by existing, state or federal laws, were considered necessary to assess the existing conditions before operations began on site. The in-place leaching technique for uranium mining eliminates the enviromental disturbances associated with open pit or underground mining. No grinding and crushing of ore is needed, nor are large tonnages of waste tailings produced. Surface subsidence is not expected since less than 5 lb of uranium is present per ton of rock and even complete removal of such small amounts should not cause subsidence. Solution mining has fewer environmental problems than conventional mining. Members of the Texas Water Quality Board recognized the differences which exist and have recently formulated new environmental control procedures which apply specifically to solution mining. Some of the solution mining activities which are of particular concern are discussed in the following pages. Process Description The produced uranium-bearing solution is pumped through a pipeline from the pattern area to the plant area. The first pattern area consists of a nest of 125 fluid injection, production, and monitor wells [(Fig. 1)]. Injection wells have 4-in. casings and are spaced 50 ft apart on a square grid. Production wells have a 6-in. casing and are located in the center of each square. A block flow sheet of the plant is given in [Fig. 2]. The produced solution goes through parallel trains, each consisting of a carbon column and an ion exchange column in series. The carbon column removes any sand present in the produced solution and the ion exchange column extracts the uranium. The depleted solution is treated with chemicals and returned to the field for reinjection. The uranium retained in the ion exchange column is removed periodically with a sodium chloride solution. Uranium-bearing solution from the ion exchange column is passed through a charcoal column for removal of impurities and then to a precipitation tank where the uranium is precipitated as yellowcake slurry. The yellowcake slurry is clarified, filtered and dried to produce a granular yellowcake product. Environmental Considerations Sources of waste solutions to storage reservoirs, the backwash reservoir and atmospheric discharges are shown in the block flow sheet [(Fig. 2)]. These waste solutions pose a relatively small problem and are adequately controlled by conventional means. There is one area, however,

Jan 1, 1978

By Cyril Stanley Smith

ON the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1958, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Cavallo3,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold-working restored it. He encountered some samples of brass that could not be rendered magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condition, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitters in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant,9 Honda and Shimizu, 10,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1941

By Thomas M. Drown

I DESIRE to communicate to the Institute the results of a few analyses which bear on the condition of carbon in gray and white iron. These analyses were made in the course of an investigation, now in progress, of the chemical composition of "chilling" irons. It will be remembered that Bell says he found no material difference in the amount and condition of carbon in gray and white pig iron made at the Clarence furnace, in England, and he therefore refers the difference in color and appearance in these two varieties of iron to the size of the particles of graphite. I quote from his "Chemical Phenomena of Iron Smelting:" "The inference I would draw from the information afforded by these analyses is, that the condition of iron in respect to its so-called 'richness' is, within certain limits, entirely independent of its chemical constitution.. .. In the fluid state, I conceive the carbon, so taken up, confers upon the iron the property of fusion much below the temperature at which the pure metal melts, and the carbon itself may be regarded as dissolved in the iron. If, during the process of manufacture, the pig metal has been formed at a low temperature, consolidation, I imagine, takes place under such circumstances that the crystals are so minute, and the carbon which is separated assumes the uncombined or graphitic form in particles so minute as to be invisible, and, in consequence, the iron is white. If, on the other hand, the furnace is working at a very high temperature, the intensely heated iron crystallizes with large facets, upon which the extruded carbon assumes the condition of distinct plates or flakes. Should the temperature be less intense, these crystals are of smaller dimensions, and the separated carbon is less conspicuous, and, as the temperature of the furnace declines, the crystals decrease in size, as do the flakes of carbon, until both disappear in white iron.. .. Returning, then, to temperature as the cause of differences in quality of pig iron, the 'chilling' of gray metal, and its conversion into white, may be regarded as the effect of preventing, by rapid cooling, the formation

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion- equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control.

Jan 3, 1954

By E. Martinez, M. L. Hollander

Sulfurization of copper oxides was investigated using differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). When mixtures of cuprous oxide and sulfur were heated, the surface of the cuprous oxide was converted to cupric sulfide at the melting point of sulfur (119°C); additional sulfuriza-tion took place when the sulfur vaporized above 200°C. Cupric oxide also reacted with sulfur to form cupric sulfide but the starting temperature was approximtely 225°C. When the cupric oxide and sulfur were physically separated, sulfurization still occurred indicating a reaction with the vapor phase of sulfur. Sulfurization was obtained in runs with cuprite, chrysocolla and basic copper carbonate. Further decomposition of cupric to cuprous sulfide was noted at somewhat higher temperatures. The DTA-TGA data made it possible to set up postulated reactions in each system. These techniques were found to be well suited for studies of this type. Because of the difficulty encountered in flotation of many metallic oxide minerals, efforts have been made to find suitable reagent combinations to sulfi-dize these minerals in the flotation circuit. Recently Bautista and Sollenberger,1 using a different approach, showed that the surfaces of many oxide minerals can be converted to sulfides by heating them with sulfur to temperatures between 150° and 225°C. This technique was effective even with chrysocolla, a mineral which is very difficult to sulfidize. The primary objective of the present study was to obtain information on the reactions between the oxide minerals and suIfur. A better understanding of the mechanisms involved might prove useful in pointing the way to improvements in the process. A secondary objective was to demonstrate the value of thermo-analysis in investigations of this type. Bollin and Kerr2 have reported the use of a modification of differential thermal analysis to study the thermal reactions which occur on heating elemental constituents in a closed system to synthesize copper sulfides and iron sulfides. Differential thermal analysis (DTA) was used to detect enthalpic changes as mixtures of minerals and sulfur were heated. The DTA indicated the temperatures at which reactions started and whether they were exothermic or endothermic. Weight change data were obtained by thermal gravimetric analysis (TGA). These data could often be used to support postulated reactions and to eliminate consideration of other possible reactions. EQUlPMENT Differential thermal analysis (DTA) involves measuring the temperature difference between the sample being tested and a thermally inert reference, generally aluminum oxide, as both are heated at a uniform rate. Series connected thermocouples in the sample and reference are used to detect the temperature differences that occur as the sample undergoes enthalpic changes.3 Crystalline transitions, fusions, vaporizations, dehydrations, decompositions and many solid state reactions can be detected. A DTA unit manufactured by the Robert L. Stone Co., Austin, Tex., was used in this investigation with a temperature rate increase of 10°C per min. The samples and reference were placed in Inconel cups with wells in the bottom into which the differential thermocouples fit, and run in a nitrogen atmosphere. Thermal gravimetric analysis (TGA) measures the changes in weight that a sample undergoes as it is heated. A Chevenard thermobalance converted electronically for graphic recording was used with a heating rate of 5°C per minute. An X-Y recorder plotted temperature on the X axis and weight changes on the Y axis. A flow of 250 ml per min of nitrogen was streamed through the furnace. Samples were placed in a porcelain crucible open at the top, unless otherwise noted. EXPERIMENTAL RESULTS Sulfur: Two sulfur samples from different sources were tested. The DTA of a high purity sulfur and a reagent grade sublimed sulfur are shown in Fig. 1. Nearly all the tests were run with the sublimed sulfur due to the difficulty in grinding and high electrostatic charge encountered with the high purity sample. Sulfur undergoes three endothermal reactions below 200°C. The first is a solid-solid crystalline transi-

Jan 1, 1964

By H. J. Fraser

LIKE a runner catching his second wind, the mining geologist in 1944 has had some opportunity to appraise the result of three years of active and intense search for the metallic sinews of war and peace. The war period has been one of physical activity and accumulation of new data but has not so far resulted in the announcement of any profound or revolutionary theoretical concepts or techniques. Most technical publications during the year have been either descriptive or statistical. A review of accomplishments during the war years, although affording some measure of satisfaction in individual cases or regarding production of certain metals or' ores, is far from justifying any feeling of complacency regarding the growth of the profession either in fundamental knowledge or in application. During 1944 an abundant supply of all metals and minerals flowed steadily to smelters and fabricating plants. Also, during this and preceding years, adequate stock piles for war needs, in view of the improved foreign and domestic supply situation, were accumulated in many metals in such quantities that the mining industry has become concerned not with the problem of supply but with the effect these accumulated stocks, if maintained, might have on the postwar market. These considerations culminated in the enactment by Congress of the Surplus Disposal Act, which, admittedly a tempo-

Jan 1, 1945

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By M. J. Williams, C. P. Proctor, J. T. Crawford

The purpose of this paper is to present some data and comparisons regarding three types of Rheolaveur plants washing bituminous coal from the Pittsburgh seam. It deals only with the sections that handle coarse coal. The Rheolaveur system consists of launders or troughs in which coal and its associated impurities are conveyed by water. The impurities. being heavier than the coal, settle toward the bottoms of the launders and are drawn off through specially designed openings called Rheo boxes. Fundamentally, each plant consists of straight-sided, flat-bottomed launders of varying width and length, each launder equipped with one or more Rheo boxes for the removal of high-grauity fractions of the feed that are undesirable in the cleaned coal. Each launder has at least two longitudinal sections, the first with a slope of from 11/2 to 4 in. per foot of length, called the classification section. The single-box launder has a classification section followed by a washing section ahead of the box. A two-box launder is a single-box launder followed by a washing section and a second box. The slope of the washing section between the first and second boxes is determined to some extent by tonnage. At the end of the classification section, which may. vary from 8 to 15 ft. in length, the slope abruptly flattens out to a slope of from 92' to 1 in. per foot of length. This flatter section of the launder, called the washing section, may vary from a few feet, in a single-box launder, to 15 ft., in a two-box launder. Raw coal entering the head end of what we choose to call the "primary" launder or launders is pushed down the classification section by a stream of water entering the head end of the launder with the coal. As it strikes the washing section, of lower pitch, the velocity of flow is retarded and the heavier particles of slate, pyrite, bone, etc., take their places on the bottom and are drawn off as they pass over the Rheo boxes. The clean coal, of lighter gravity, remains on the top of the stream of

Jan 1, 1938

By M. J. Williams, C. P. Proctor, J. T. Crawford

The purpose of this paper is to present some data and comparisons regarding three types of Rheolaveur plants washing bituminous coal from the Pittsburgh seam. It deals only with the sections that handle coarse coal. The Rheolaveur system consists of launders or troughs in which coal and its associated impurities are conveyed by water. The impurities. being heavier than the coal, settle toward the bottoms of the launders and are drawn off through specially designed openings called Rheo boxes. Fundamentally, each plant consists of straight-sided, flat-bottomed launders of varying width and length, each launder equipped with one or more Rheo boxes for the removal of high-grauity fractions of the feed that are undesirable in the cleaned coal. Each launder has at least two longitudinal sections, the first with a slope of from 11/2 to 4 in. per foot of length, called the classification section. The single-box launder has a classification section followed by a washing section ahead of the box. A two-box launder is a single-box launder followed by a washing section and a second box. The slope of the washing section between the first and second boxes is determined to some extent by tonnage. At the end of the classification section, which may. vary from 8 to 15 ft. in length, the slope abruptly flattens out to a slope of from 92' to 1 in. per foot of length. This flatter section of the launder, called the washing section, may vary from a few feet, in a single-box launder, to 15 ft., in a two-box launder. Raw coal entering the head end of what we choose to call the "primary" launder or launders is pushed down the classification section by a stream of water entering the head end of the launder with the coal. As it strikes the washing section, of lower pitch, the velocity of flow is retarded and the heavier particles of slate, pyrite, bone, etc., take their places on the bottom and are drawn off as they pass over the Rheo boxes. The clean coal, of lighter gravity, remains on the top of the stream of

Jan 1, 1938

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1' the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man' permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if' the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a'Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a'Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955

By Wallace W. Key

Chalk is a natural calcium carbonate occurring as the remains of soft, friable, minute marine organisms. Whiting can be either finely ground calcium carbonate prepared from chalk, marble, or limestone or the product obtained by chemical precipitation from a solution or suspension containing lime. Until relatively recently, whiting made from limestone was termed "whiting substitute," but it is now usually designated as limestone whiting. Precipitated calcium carbonate, sometimes called "precipitated whiting" or "precipitated chalk," is a finely divided calcium carbonate product obtained by chemical precipitation from a solution or suspension containing lime. Considerable quantities of precipitated calcium carbonates are produced from many chemical processes. Naturally occurring calcium carbonate in a variety of crystalline forms and in all degrees of chemical purity forms a substantial part of the earth's crust. Exactly where a chalk grades into a marl or calcareous shale through increase of clay or silt or into a hard limestone through consolidation and crystallization is difficult to determine because no rigid specifications have been promulgated for classifying them. Composition and Properties Once considered to be amorphous, chalk was later found to be cryptocrystalline. In the pure state it consists entirely of CaCO3, but many deposits are impure. When impurities are removed and the material is reduced to a finely divided state, it is known as chalk whiting. Much confusion attends the use of the term "chalk" as well as the classification of whiting materials. For instance, blackboard chalk is not necessarily chalk but is sometimes plaster of paris or a form of talc. Colored "chalks" may be true chalk colored and compressed with a binder but are probably such materials as hematite, clays, or carbonaceous matter. The term whiting was applied exclusively to the product derived from true chalk before World War I. Chalk imports were difficult to acquire during World War I, and whiting substitutes, a term applied to the products derived from natural rock deposits and precipitated calcium carbonate, were introduced. Substitute whitings were not acceptable at first, but it was found that blending true chalk with substitutes often created an improved product; eventually by selection of limestone and finer grinding, products not only acceptable, but for some uses superior to chalk whiting, were developed. Gradually the term "substitute" was dropped because chalk whiting had lost its importance, being largely supplanted in the United States by other whiting materials. Whiting is now made in ever-increasing quantities from limestone, marble, dolomite, marls, vein calcite, oyster-shell, as well as primary and byproduct precipitated calcium carbonates. Distribution of Chalk Europe-In England, France, Belgium, Denmark, and other European countries highpurity chalk occurs in extensive beds. The Cretaceous period, or the "age of chalk," in geologic history receives its name from the great deposits of chalk exposed on either side of the English Channel. It has been estimated that oceans in which chalk and allied deposits were formed covered more than 500,000 square

Jan 1, 1960

By W. A. Eardley

FIFTEEN years ago the world's deepest oil well penetrated the earth about 7300 ft. That depth has now been more than doubled. Why has such deep drilling become necessary and how has it become possible? Three factors have had an important bearing: (1) Depletion of shallow zones, making it necessary to search for deeper producing measures. (2) The perfection of prospecting methods, which have been success- fully used to locate favorable buried structures, many at great depth. (3) Improvement in the quality of steels used for drilling.

Jan 1, 1940

By L. A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region comprises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County. In this upper Gulf Coast region, which embraces the most heavily populated and industrialized parts of Texas, industrial and municipal water supply is obtained chiefly from wells. Largest center of ground-water withdrawal is the Houston-Baytown area, where about 200 million gallons per day was pumped in 1956 for municipal and industrial use. Other large centers of ground-water withdrawal include the Alta Loma sector and the heavily industrialized Texas City area in Galveston County, where about 23 mgd was pumped in 1956. In the Freeport area in Brazoria County about 6 mgd was pumped in 1956 for city and industrial supply. In addition to withdrawals in metropolitan districts, great quantities of ground water are supplied by irrigation wells to thousands of acres of rice. These wells are widely dispersed over many miles, principally in Harris, Waller, Fort Bend, Brazoria, and Liberty counties, and effects of pumping are not so readily noticed as in the industrial and metropolitan sectors. Subsidence: Starting with the 1905-1906 line from Smithville, Tex., to Galveston, the U. S. Coast and Geodetic Survey has extended a network of first and second-order level lines throughout the upper Gulf Coast region. In 1918, when a line was run from Sinton, Tex., to New Orleans, La., a tie was made to the 1905 leveling at Houston. In 1932-1933 a line was run from Palestine, Tex., to Houston, and a good deal of leveling was carried out in the vicinity of Houston. At this time the entire network was adjusted to the Sea Level Datum of 1929. In 1935-1936 and 1942-1943 several new lines were run and considerable releveling was performed. Supplementary adjustments were made after both the 1936 and 1943 levelings in order to reduce the elevations to the Sea Level Datum of 1929. These adjustments probably masked some of the subsidence that had occurred up to that time, although a certain amount of subsidence was noticed in the 1943 leveling. When several lines in the vicinity of Houston and Galveston were releveled in 1951, the regional nature of the subsidence became apparent.' Direct comparison with the 1943 leveling was possible because the datum was not changed. Comparisons with prior leveling were unreliable because of differences in the early and subsequent datums. In 1953-1954 many lines in the region were re-leveled and in 1957 the entire network, including the elevations previously determined, was readjusted to determine the changes in elevations as indicated by various levelings between 1905 and 1953-1954. In this instance the adjusted elevations were held fixed near the boundaries of the region where the bench marks seem to have remained stable. The only sea-level connection held fixed was the connection of the 1905 leveling to the 1903-1906 tidal series at Galveston. Almost the entire region has been at least slightly affected by the subsidence, some areas to a great extent. The profiles of subsidence (Fig. 2) and the map showing the contours (Fig. 3) illustrate both regional and local changes. A large area of subsidence is centered in the Houston-Baytown district, where the maximum recorded is about 2.7 ft between 1905 and 1954. This probably falls short of the actual maximum, since land surface subsided as much as 2.5 ft in the industrial section alone between 1943 and 1954. Sub-

Jan 1, 1960

A. M. CANDY,* Pittsburgh, Pa.-I think more stress should be laid upon the question of welding with the carbon electrode, which we ordinarily call graphite arc welding. Mr. Miller's photograph indicated that the original parent metal had been decarburized to a marked degree. It would be interesting to know the carbon content of the parent metal, and whether or not Mr. Miller has made any investigations to determine if the metal is always decarburized or whether in some instances we actually have carbon injected into the weld, which has been the understanding that has been quite prevalent. There were one or two other points that Mr. Miller brought out concerning which I desire to ask one or two questions: The illustrations that he presented were obtained with what, I suppose, would be termed a real low-carbon steel welding wire, which gives in the deposited metal grains that are more or less symmetrical, whereas the Roebling electrode, which is a mild steel of higher carbon content, apparently gives a columnar structure. I do not know which-of these I structures is more desirable, but assuming that the structure produced by the really low-carbon steel wire is the more desirable, would it not be true that the very low carbon content would, probably owing to high temperatures that prevail in the arc, result in a greater amount of oxidation and probably result in either carrying into the weld more oxide or producing more oxide on the surface as the operator progresses? The short arc is an advantage in all cases. Whether Mr. Miller's trouble is oxide or nitride, the short arc helps him out, because the closer the end of the electrode is to the work the less chance there is for either oxygen or nitrogen to get in. And whichever is the cause of the trouble, the short arc keeps it out by lessening the time in which the steel is molten and the amount of air that gets in. It also makes sure that the molten metal will not fall into the crater. Everything is in favor of the short arc.

Jan 4, 1919

By H. M. St. John

Like every present-day manufacturer, the brass foundryman is faced with the necessity of reducing the cost of his finished product without impairing its appearance or quality. He must use every economy that the progress of art and science puts at his disposal and should also be alert to profit by any peculiarity in his own situation or the nature of his product that may give him an exceptional advantage. Much can be accomplished by the adoption of labor-saving equipment and improved methods of melting, molding and handling. Control of pouring temperature, study of defective castings and their causes, laboratory control of molding sand and core mixtures, the use of less expensive alloys, all contribute to the desired end. Assuming that the composition of the alloy is already as inexpensive as the character of the casting will permit, still further savings can be made by the intelligent purchase and utilization of the metals needed to produce the desired analysis. Functions of Secondary and Virgin Metals in Casting Brass It is no longer a general assumption among foundrymen that quality castings must be made from an "all virgin" mix. If suitable secondary metals can be obtained more cheaply it is wasteful to use any larger proportion of virgin metal than is required to produce castings of the desired properties. To follow such a course, however, imposes upon the foundryman a heavier obligation than was formerly the case, to make sure by test and inspection that his castings really are of the desired quality. So long as he used the most expensive grades of metal and his melting practice was reasonably correct he was not obliged to give much thought to the quality of the metal in the castings. If he is to use secondary metals he must, in order to retain the confidence of his customer, examine these metals very carefully before use, exercise scrupulous control over his melting and pouring conditions and examine his castings closely. These statements apply more particularly to the jobbing foundry. The foundry department in a manufacturing plant is in a somewhat

Jan 1, 1930

By James F. Kemp

Discussion of the paper of JAMES F. KEMP, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1801 to 1836. WALLACE E. PRATT, Manila, P. I.-I am glad that Professor hemp has referred to the Philippine ores in his paper, inasmuch as I have had the privilege of examining, in a preliminary way, the ores there. I must say, from the resume given us, that the Daiquiri ores seem to be similar in origin and character to the magnetite-hematite ores in Bulacan Province, Philippines. Professor Kemp has also referred to C. M. Weld's description of the magnetite-hematite ores at Hongkong and to the similarity of these ores to the ores at Daiquiri and to those in Bulacan. There is a minor feature of apparent difference in origin in the Hongkong and Bulacan ores. Mr. Weld believes the iron ores at Hongkong to have resulted from the intrusion of the Hongkong granite, a distinctive rock of wide distribution in the Orient, into sedimentaries which are probably of much greater age than those which have been replaced in part by the ores in Bulacan. Associated with some of the ores in Bulacan and elsewhere in the Philippines there is a granite which may be the equivalent of the Hongkong granite; but the Bulacan ores are not related in origin to the intrusion of this granite, which is clearly older than the ores, but to the later intrusion of dikes and small bodies of basic rocks into the granite and into associated tuffs, breccias, and sedimentaries, including limestone. I gather that the intrusives to which the mineralization is related at Daiquiri are also small in volume and later than larger bodies of associated igneous rocks, from which it would appear that the Bulacan ores are even more closely related to the Daiquiri type than are the Hongkong ores. The deposits in Bulacan are inaccessible and are not large, the largest one containing about 1,000,000 tons, according to an estimate based solely on its outcrop dimensions. Ores of similar character, however, occur in Camarines Province in apparently larger quantity and in a situation on the coast adjacent to deep water.

Jan 12, 1915

By D. Hodouin, T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performance of various flowsheets. For a given flows he et configuration, unit process dimensions, and operating conditions, the simulator calculates the steady-state values of the process variables and determines the conditions that meet the required operation criteria for tonnage and product quality. Calculation examples are proposed for the design of wet and dry grinding circuits. The performance of different configurations of cement clinker and sulfide ore grinding flowsheets is evaluated and discussed.

Jan 1, 1986

By HOWARD N. EAVENS

DURING the year just closed the bituminous industry has been marked by a continuation of the period of low prices and a steady deflation, accompanied by the closing of mines and the consolidation of small units into larger ones. This pro- gram has marked almost every field in the country, and it bids fair to continue for some time. Some figures recently published for Kentucky show that in 1924 there were 660 mines producing 45,147,000 tons; in 1928 the number had decreased to 537, while production had increased to 61,860,000 tons, and a similar movement is occurring all over the country. Prices throughout the early part of the year were very low, but during the fall and winter the prices received are more satisfactory than they were earlier in the year. One of the leading developments in the marketing of coal during the year was the trade practice movement, which began in the Harlan field, and has now been adopted in the Harlan, Hazard, Appalachian, Logan. Williamson and Kanawha fields. The purpose of this movement is to prevent the shipment of coal except on order, and by the publication of price lists to prevent much senseless price quotation. Where it has been practised the longest this movement has resulted in a considerable degree of stabilization, and, undoubtedly, it will help existing conditions very materially if it becomes universal.

Jan 1, 1930

By N. J. Grant, R. Nordheim

An extensive study was made of the aging characteristics of alloys based on the 80 pct Ni-20 pct Cr composition hardened with aluminum and/or titanium, each up to 4 pct. Aging was followed by means of hardness and hot electrical resistance measurements as well as by X-ray and microscopy. Stress rupture tests at 1500°F were utilized as a check on the predicted behavior. THE titanium and aluminum hardened Ni-Cr alloys, exemplified by Nimonic 80 and Inconel X, constitute one of the more important groups of alloys developed to meet the demand for materials retaining their strength at elevated temperatures. For service in the temperature range 1200" to 1500°F, these alloys offer high creep resistance. With increasing service temperature, however, the strength of the simpler Ni-Cr base alloys falls off rapidly so that above 1500°F there is a significant loss of strength. The present investigation was undertaken with the hope that a better understanding of the factors controlling the precipitation hardening of these alloys would make it possible to increase the useful service temperature range. Primarily this investigation involved the study of the effects of titanium and aluminum on the hardening and the subsequent softening at elevated temperatures. The titanium and aluminum contents were each varied between 0 and 4 pct by weight at a constant nickel to chromium weight ratio of about 4:1. (Except when otherwise stated, all compositions are expressed on a weight basis.) The major part of the investigation was confined to alloys with less than 0.06 pct C. Recently several papers dealing with the identity of the microconstituents in the titanium and aluminum hardened Ni-Cr alloys have been published. Using X-ray analysis of the residues from anodic dissolution, Rosenbauml was only able to identify carbides and nitrides in Nimonic 80 and Inconel X. However, since Rosenbaum worked with alloys in the hot rolled rather than in the aged condition, his results are inconclusive. Recently Hignett' reported that the hardening of Nimonic 80 was due to the controlled precipitation of Ni,(TiAl) having the cubic Ni3A1 structure. Taylor and Floydv-" published the results of an investigation of the nickel-rich corner of the Ni-Cr-Ti, Ni-Cr-Al, and Ni-Ti-A1 systems. In the Ni-Ti and the Ni-A1 systems the hexagonal Ni,Ti phase, 7, and the cubic Ni3A1 phase, -y', respectively, exist in equilibrium with the nickel-rich solid solution. The interatomic distances in the basal plane of Ni,Ti and the octahedral planes of the matrix are almost equal, thus explaining the Wid-manstaetten type structure formed when Ni,Ti precipitates from solid solution. When Ni:,Al precipitates from solid solution, it appears usually in globular form, often dispersed along rows corresponding to definite crystallographic directions. The 7 and phases are also the only intermetallic compounds which occur in the nickel ternary alloys with up to 25 pct Cr and 10 pct Ti or Al. Taylor and Floyd found that Ni,Ti takes practically no nickel, chromium, or aluminum into solution. Nial, on the other hand, dissolves a considerable amount of chromium and titanium and some nickel. Up to three out of every five aluminum atoms could be replaced by titanium in Ni,Al. This substitution caused a slight increase (less than 1 pct) in the lattice parameter. With respect to the effect of variation in the titanium and aluminum contents on the high temperature strength of Nimonic 80 type alloys, Pfeil, Allen, and Conway" reported that an 80 pct Ni-20 pct Cr alloy containing 0.20 to 0.30 pct A1 had the highest creep resistance when the titanium content was kept between 1.65 and 2.75 pct. Experimental Procedure The materials used for this investigation were electrolytic nickel, electrolytic or low carbon chromium, sponge titanium and 2s aluminum. The alloys were melted in an indirect carbon arc furnace under

Jan 1, 1955