Search Documents

By Henry H. Angst

Tim history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 1/2-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu, yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By E. J. Krokroskia

Fletcher Mill is located in the southern part of the New Lead Belt in Southeastern Missouri, in the northwestern part of Reynolds County. Shaft sinking began in July, 1964. The mill went on stream in February, 1967, and reached the designed rate of 5,000 tons per day in July, 1968. The ore occurs approximately 1,000 feet below the surface as disseminated deposits of galena, sphalerite and chalcopyrite. There is no oxidation within the ore body and dissemination is not fine enough to present liberation problems with a normal grind. Mining is by the room and pillar method with rubber-tired diesel- propelled drilling and loading equipment. The ore is dumped through a 27-inch square grizzly into a 5,000-ton pocket. The underground primary crusher is automatically fed by a vibrating feeder and discharges directly into skip measuring bins. Hoisting is automatic, in balance, with 8. 5-ton skips dumping into a 1,000-ton mill bin. MILL The concentrator is a 5, 000 tons-per-day single section plant equipped to produce lead, zinc and copper concentrates. Contained under 35, 347 square feet of roof, without fine ore storage or remote crushing, and with sufficient automation to be operated by one man, the plant is compact, unique, and efficient in operation. The design

Jan 1, 1970

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

While coal was undoubtedly seen by the early travellers within the state, the first mention of it was in the late 1820's when hunters put some stones from a creek bed under the logs of a large camp fire, and awoke later to find the stones on fire. The stream was later named Coal Branch; the location was at the eastern side of the present Bibbs County.1 In the Louisville Daily Journal of Feb. 11, 1831, the following short editorial note appeared: "Tuscaloosa Coal.-A small quantity of this article has reached Mobile, and has been tried in the office of the Patriot; it is said to be an excellent article. We invite such of our friends as desire economy in fuel, love a cheerful and constant fire, or would eschew a smoky room, to call and examine." On a geological map published in 1832, the "Carboniferous group" is shown and a spot near Tuscaloosa indicated as showing bituminous coal,2 and this is again alluded to in Morton's Synopsis, 1834. A brief description of the coal fields in the state in 1834 said that in winter coal was brought down the. Black Warrior River to Mobile and sold there at the same price as Liverpool coal, $1.00 to $1.50 per barrel, ($10 to $15 per ton) and that the writer was using it in his laboratory.3 At that time it was in local use by smiths and an iron foundry was using it in Shelby County.4 In 1836 some coal was mined in the Birmingham district, chiefly in the northern portion of the Coosa basin, where it was loaded on barges and taken down the Coosa Rivers.5 "William Whitman dug coal out of Wolf Creek (Walker County) in 1837," and in the same county, in 1839, the first coal shaft in the state, was sunk. This was near the mouth of Lost Creek and was known as Frierson's Shaft. It was operated by a hand windlass, using two tubs.1

Jan 1, 1942

C. W. Kempton, Oro Blanco, Ariz.: In his interesting paper, Mr. Ingalls refers to reports of tin-deposits near Sain Alto, Zacatecas, Mexico. During 1891 I made some personal examinations of these deposits. They are, for the most part, located from 10 to 30 miles west of the town, in the Sierra del Fraile.

Jan 1, 1896

By William N. Page

HAVING recently made a careful professional examination of this tract, I think its peculiar geographical, topographical and geological relations may prove interesting to members, not only because they are somewhat unusual in such a combination, but also as presenting the economical conditions of a region not widely known, at the western base of the Alleghanies.

Jan 1, 1889

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

E. T. Dumble, Houston, Texas (communication to the Sec-retary?):—In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references:— Sludi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo New-berry. Department of Mines, Victoria (1892).

Jan 1, 1905

By W. J. Kroll

W. J. Kroll (Belgium)—Those who are acquainted with the metallurgy of our forefathers may have occasionally a good time when glancing at recent publications in which aged discoveries are unconsciously reported as novelties. We know very well, that oxygen blowing of iron has been described by old Bessemer. The author of the present article is, however, not aware of the fact that the process he describes, the fused salts scrubbing, was already used in the middle of the last century by St. Claire Deville in his attempts at making higher-purity aluminum from raw AlCl3 by sodium reduction. The same fact escaped the three investigators to whom the author refers. The technical grade AlC13 produced by St. Claire Deville from impure oxide, chlorine, and carbon (Oersted process) was contaminated with Sic4 and FeC13, which he removed on an industrial scale by various methods.' He sublimed, for instance, his chloride in contact with iron nails, or aluminum chips, or in hydrogen, which reduced the FeC13 to the less volatile FeCl2. He used also alkali-alkaline earth chlorides as a solvent for A1C13 and FeC13 in presence of iron as a reducing agent, and sublimed his purified AlC13 from solvent salts. The successors of Deville used also zinc or lead as a reducing agent. These methods were later used currently for the purification of BeCl2 and for collecting this compound in a salt bath, suitable for fusion electrolysis. More recently, the same Deville process has been described as applied to the purification of ZrCL4, as part of a method of extraction of ZrCL4 from silico zirconium, which later was reacted with FeC12 in a separate part of the equipment. According to the patent referred to3 the ZrCL4 is dissolved as a gas in a carrier salt such as alkali-alkaline earth chloride, from which it can be reclaimed in a purified form by distillation. A bath of NaCl/KCl is recommended in the specifications. The FeC12-FeC13 go in the salt solution in which raw ZrCl4 is introduced by bubbling, while Sic4 and Tic4 pass through the bath and escape in the atmosphere. purification by this salt-solvent method is thus well described. It may be worth while insisting on some minor details about which the author did not bother too much. One of these concerns the material of construction for the container. If iron is used, and if no other reducing agent is added, then it is the iron of the pot that acts as a reagent in the breakdown of FeC13 to FeCl2, and corrosion can be expected. This shows the importance of using extraneous large surface-reducing agents, of which there is a choice. Zir-

Jan 1, 1963

By W. R. Ingalls

THE propaganda in favor of the adoption of the metric system of weights and measures in the United States is founded upon the idea of compulsory adoption. There can be no argument about this, for the metric system has been legal, by Act of Congress, in the United States since 1866. Nobody ought to oppose an educational movement, and if pro-metric activities were confined to that there might be no reason to gainsay them. I do not propose to enter into any discussion of 'the relative merits of the metric and the English systems of weights and measures. The simple case is that the metric system not having made much headway in the United States after more than 50 years of legality, 'it is now aimed to force it upon the people by legislative compulsion. The main arguments in favor of such compulsory adoption are that it would- simplify the education of our children and would promote our foreign trade, for the reason that more countries of the world, with which we do business, use the metric system than the English system. I am going to disregard,' in this contribution, the first of these arguments, for it is largely conjectural." Not so with the other, which is specific, and being so its speciousness can be, proved. It is true that the metric system is used by more countries of the world than the, English system. It is commonly stated that of the Indo-European nations only the United States, Great Britain, and her colonies, and Russia have failed to adopt it. However, if with "colonies" we equate Canada, Australia, New Zealand, Tasmania and South Africa, we have a longer list of non-metric countries, and it comprises not only the most populous, but also the most industrial nations of the world.

Jan 1, 1921

By Pierre I. Desré, Donald T. Hawkins, Ralph Hultgren

The torsion effusion method has been used to measure the vapor pressure of thallium over pure thallium in the temperature range 931" to 996'k The resulting 100 cal per g-atom is in excellent agreement with previous values. Vapor pressures of T1 above seven Ag-Tl alloys ranging from 33 to 90 at. pct T1 were measured at 979K. Calculated silver activities show a positive deviation from Raoult's law, approaching ideality near the liquidus. Measured thallium activities scatter less than previous measurements using the electromotive force technique. Values for the silver component were calculated by Gibbs-Duhem integration. This paper reports the results of a study of the liquid Ag-T1 system by the torsion effusion method. The method has been discussed in detail previously1 and will be only briefly summarized here. The sample is contained in a cell which is suspended on a torsion wire. Vapors effusing from orifices on opposite sides of the cell exert a torque on the wire. The torque is related to the vapor pressure by the following relation: where D is the torsion constant of the wire, 4 the angle of torque, fl and f2 the correction factors determined by Freeman and seamy2 to account for orifice length, a1 and a2 the areas of the orifices, and ql and q2 the distances of the orifices from the axis of rotation. By using the same cell for pure thallium and the alloy, it follows that: so that most systematic errors are eliminated in determining the activities. EXPERIMENTAL 99.999+ pct T1 was obtained from the American Smelting and Refining Co. and 99.999 pct Ag was obtained from Cominco American, Inc. Seven Ag-T1 alloys, ranging in composition from x^\ = 0.33 to 0.90, were prepared by melting together weighed amounts of the pure metals in sealed, evacuated Vycor tubes and quenching the melts in water. The apparatus and graphite cells were the same as those used by Hawkins and Hultgren3 in their study of the Pb-Sn system. RESULTS Ten measurements were made on pure thallium in the temperature range 931" to 996K, and the results are presented in Table I. Values of were calculated using tabulated Gibbs (free) energy functions.4 No dependence of on temperature or orifice size was found, indicating that equilibrium was attained. Data for the Ag-T1 alloys are shown in Table 11. Values were smoothed with respect to composition by a plot of where . DISCUSSION The value = 43,520 * 100 cal per g-atom for pure thallium (95 pct uncertainty limit) is in excellent agreement with previous investigations.4 In the Ag-T1 system, this study shows positive deviations from Raoult's law at all compositions. Fig. l gives the phase diagram according to Hansen, and Fig. 2 presents the activity values measured in this study as well as those from electromotive force measurements at 950°K by Terpilowski, Kundys, and slaby.'

Jan 1, 1969

By L. Burris, C. H. Stockman, I. G. Dillion

Zone melting is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Equations are presented which 1—predict the concentration profiles after successive passes of the zone and 2—give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing in the last zone length. These equations were solved numerically using an electronic computer, and the concentration profiles are presented as a function of the solute distribution coefficient and the ratio of molten zone to total bar length. ZONE MELTING is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Separation occurs if the solid freezing from a solution at any moment has a composition different from that of the liquid from which it is freezing. Solutes which lower the freezing point will tend to remain in solution and will be moved in the direction of zone travel. Solutes which raise the freezing point will preferentially freeze out, and they will be moved in a direction opposite to that of zone travel. After repeated unidirectional passage of a molten zone through a bar of material, impurities will be concentrated in the ends of the bar. A limiting concentration gradient will be reached in the bar after a large number of passes of the molten zone. Both the magnitude of this limiting concentration gradient and the rate of movement of solute in any pass depend on the zone length and on the equilibrium concentrations of solute in the liquid and solid phases. The basic theory of zone melting was thoroughly covered by Pfann.1 The purpose of this paper is to extend the theory of zone melting by presenting 1—equations which relate the concentration profiles in successive passes of the zone and 2—equations which give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing* in the last zone length concentration of a given solute in the solid to the concentration of the same solute in the liquid. Analytical methods for determining the concentration profiles after any pass have been developed by Lord2 and Reiss. The method developed by Lord does not take into account normal freezing in the last zone and also becomes very complicated when the number of passes becomes large. The method developed by Reiss enables the direct calculation of the complete concentration profiles (including that in the last zone) after any pass for values of k close to unity (0.9 < k < 1.1). Both methods are useful and provide valuable insight into the zone melting process. The equations given in this article are based on the same assumptions used by Pfann. These are: 1—uniform composition in the liquid, 2—negligible diffusion in the solid, 3—constant distribution coefficient, 4—constant length of the liquid zone (except at the ends), and 5—solubility of the solute in the melt is not exceeded at any point. Equations for Concentrations in Successive Passes For a melted zone of length 1 at the left-hand end of a bar of uniform unit cross-section, the amount of solute in the liquid is J0Cn-1(x) dx [1] where the subscript is the number of the pass. Cn-1(x) represents the concentration (expressed as weight per unit volume) obtained in the previous

Jan 1, 1956

By H. W. Schreiber, G. R. Castle

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties. Many of these small companies don&apos;t have the financial resources to pay for development costs from their own funds and frequently they do not even have the financial strength to permit them to borrow the money needed for development. A project financing can sometimes be arranged in such a way as to solve this dilemma. A typical project financing will not provide the answer to the "little guy&apos;s" problem because most project financings require that the sponsors of the project provide completion undertakings and sometimes other undertakings. These undertakings are often a prerequisite to obtaining financing, and if the sponsor is not financially strong enough to provide the comfort that the lenders require, then the sponsor will have difficulty obtaining financing no matter what undertakings are offered. However, with a little imagination and the right set of circumstances, a project financing can sometimes provide the solution to the small mining company&apos;s problem. The Strathcona Sound Project is unusually suited as a case study because the sponsor, Mineral Resources International Limited,(MRI) was able to arrange a project financing for the development of the project even though the lenders probably would not have been willing to loan a similar amount of money direct to MRI based on the full faith and credit of MRI&apos;s balance sheet. The way that MRI was able to arrange this financing makes for an interesting story. THE CASE In early 1974, MRI owned 100% of a small to medium sized zinc - lead - silver massive sulfide deposit (Property) located 475 miles north of the Arctic Circle less than two miles from deep water on Strathcona Sound which is a shipping zone in the Canadian Arctic. The Property was situated at a desolate location except for an Eskimo settlement (Arctic Bay) which was about 20 miles west of the Property. In other words, the project required that complete infrastructure would need to be installed in this far northern location. Independent reserve and feasibility studies (Study) had been completed on the Property which confirmed a total of 6,825,000 tons of reserves classified and summarized as shown below on Table I: [ ] These reserves were based on 229 diamond drill holes totalling 58,909 feet and were established on a cut-off grade of 7% zinc and a minimum mining height of seven feet. The overall mining recovery rate was estimated at not less than 85% and not more than 90%. The feasibility study indicated that it would cost an estimated $45,044,000 to develop an underground mine, a concentrator, a town-site, a power plant, storage facility, loading dock, a tailings disposal area and an airstrip on the Property with an annual capacity of 525,000 tons of ore per year. The construction period was expected to take two years and projected capital costs were broken down as set forth below on Table II:

Jan 1, 1985

By Mary Louise Theodore, R. G. Aspden, D. A. Colling

T RACES of sulfur have a marked influence on the physical and mechanical properties of many iron-base alloys. The commonly used combustion method for the determination of sulfur content is not accurate enough at the 50 ppm level by weight and below to be useful in determining the influence of sulfur. Kriege and Wolfe&apos; have described a method for the determination of sulfur in iron alloys in which the sulfur is evolved as hydrogen sulfide followed by reaction with N, N-dimethyl-p-phenylenediamine, and iron (111) to form methylene blue which is measured spectrophoto-metrically. This method of determining sulfur has been used to study the activity of sulfur in Fe-Si-S alloys,&apos; but has not been previously applied to the determination of sulfur in Fe-Ni alloys because of the insolubility of nickel in dilute hydrochloric acid. Dissolution of nickel in dilute hydrochloric acid, however, can be greatly accelerated by the addition of a small amount of platinic chloride.3 By combining these two techniques in a procedure in which 0.005 pct platinic chloride in 1:l hydrochloric acid is used as the dissolving fect on the strength of the material. However, ductility is influenced by the presence of discontinuous precipitation. In Fig. 5, percent elongation data at room temperature and 1400°F is shown for two sets of specimens of Waspalloy which were solution heat treated at 1950°F and either quenched or slow cooled to the aging temperature and then aged for 100 hr at 1292" and 1598ºF, respectively. At room temperature the existence of a discontinuous precipitation cell at grain boundaries (see data point marked by arrow) has no apparent effect on ductility. However, at elevated temperatures a pronounced lowering of ductility occurs when discontinuous precipitation has occurred in the specimen. It would appear that the morphology of discontinuous precipitation "cells" at grain boundaries would be highly conducive to the initiation of cracks which in turn lead to premature "grain boundary" failure.

Jan 1, 1970

By F. M. Lewis, Johnson. E. C.

BY now application of the liquid-solid cyclone to various classification problems in the chemical and metallurgical fields is more or less familiar. A less publicized application receiving wider consideration as time goes on is its use as a classifier in closed-circuit grinding operations. This paper presents the costs involved and the experience gained from operating a unit of this kind. In May 1951 the Tennessee Copper Co. installed in its London mill at Copperhill, Tenn., a liquid- solid cyclone in closed circuit with a 6x12-ft ball mill. The circuit in which this cyclone is used is the regrind or secondary grinding circuit of a copper flotation plant. Originally it consisted of a 7x1-ft conical ball mill in closed circuit with a bowl classifier. Changes made in the primary grinding circuit of the mill necessitated a regrind circuit of greater capacity. The bulk concentrate to be ground was raised from 900 or 1000 tpd to 1200 or 1300 tpd, and to accommodate this increase a 6x12-ft ball mill which had been in the primary grinding circuit was moved into the regrind circuit. When this was done it was found that the classifier was too small to give efficient operation. Space in the plant was at a premium, and since use of the cyclone offered considerable economy the installation shown in Figs. 1-3 was made.

Jan 6, 1954

By W. H. Hoffman

At the Glen Summit meeting (Trans., xx., 605) I described in a general way the grinding-machine known as the Sturtevant mill, built by the Sturtevant Mill Co., of Boston, Mass. My first experiments in granulating magnetic. iron-ores with this machine were made five years ago in the northern portion of New York State.

Jan 1, 1893

By Frank A. Herald

Through the generous cooperation of the authors of the papers in this chapter, a great wealth of fundamental data is being made available. The same plan of securing and submitting data will be carried forward next year, with the hope of making a nearer approach to complete presentation of the data contemplated in the plan. In order to conserve space, we are printing below such footnotes as have general application to Table 1 in the papers in this chapter: Footnotes to Column Headings Table I In areas where both oil and gas are produced, unless gas is marketed outside the field, such areas are included in column headed "Oil." Manufacture of casinghead gasoline and carbon black is interpreted as outside marketing of gas. Production per acre is determined by dividing into the number of barrels of oil the sum of the number of acres assigned to "Oil" plus such number of acres of the total assigned to "Oil and gas" as represents the portion thereof occupied by oil. Wells producing both oil and gas are classified as "Poducing oil only" unless gas from them is marketed off the lease. W. water; G. gas; A, air. Bottom-hole pressures are preceded by "e." All other figures represent pressures at casinghead with well closed. P, paraffin; A, asphalt; M, mixed. 0 Cam, Cambrian; Ord, Ordovician; Sil, Silurian; Dev, Devonian; Mis, Mississippian; MisL, Lower Mississippian; MisU, Upper Mississippian: Pen. Pennsylvanian; Per. Permian; Tri, Triassic; Jur. Jurassic; CreL, Lower Cretaceous; CreU. Upper Cretaceous; Eoc, Eocene; Olig, Oligocene; Mio. Miocene; Pli. Pliocene. 6, sandstone: SH, sandstone, shaly; Ss, soft sand; H, shale; L, limestone; LS, limestone. sandy; C, chalk; A, anhydrite; D, dolomite; Da. arkosic dolomite; GW, granite wash; P, serpentine. Figures are entered only for fields where the reservoir rock is of pore type. Figures represent, ratio of pore space to total volume of net reservoir rock expressed in per cent. "Par" indicates that the reservoir rock is of pore type but said ratio is not known by the author. "Cav" indicates that the reservoir rock is of cavernous type; "Fis," fissure type. A, anticline; AF, anticline with faulting as important feature; Af, anticline with faulting as minor feature; AM, accumulation due to both anticlinal and monoclinal structure; H, strata are horizontal or near horizontal; MF, monocline-fault; MU, monocline-unconformity; ML, monocline-lens; MC, monocline with accumulation due to change in character of stratum; MI, monocline with accumulation against igneous barrier; MUP, monocline with accumulation due to sealing at outcrop by asphalt; D, dome; Ds, salt dome; T, terrace; TF, terrace with faulting as important feature; N, nose; 9, syncline. Information will be found in text as indicated by symbols: A, name of author, other than above. who has compiled the data on the particular field; C, chemical treatment of wells; G, gas-oil ratios; P, proration; U, unit operation; R, references; W, water; 0. other information.

Jan 1, 1934

By D. T. Van Zandt

IN the late 1920&apos;s rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940&apos;s the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole.

Jan 8, 1954

Development: Iron Ore In Peru Utah Construction Co., of San Francisco and a Peruvian Government corporation have signed an agreement for development of a large iron orebody in Peru. Most tests show 60 pct iron or better. Most of the ore is magnetite. Although ore will be shipped mainly to Eastern U. S. blast furnaces, shipments to the West Coast may develop as the orebody opens up. The construction firm indicated three American steel companies have shown interest in the project. The orebody is located 300 miles south of Lima and about 15 miles from the coast at the same longitude as New York City. Allen D. Christensen, executive vice-president of Utah Construction noted that the distance is shorter between Peru and the East Coast. The ore deposit measures about four to five miles in one direction and 10 miles in the other. As many as 15 outcroppings within these limits have been reported. Several of the outcroppings are thousands of feet long by several hundred feet wide, Christensen said. Shipments between 100,000 and 200,000 tons of ore per month are projected by the company. Cost of opening the mine to production may go over $5 million, Christensen said. It would include building of docks for ocean going vessels, housing, and heavy duty mining and processing equipment. The contract with the Peruvian government gives Utah Construction six to eight months for additional tests and a 20 year concession for mining the orebody. Peru will collect royalties on all ore. The company will also supply about 300,000 tons per year for an electric furnace to be installed by the Peruvian Government at Chimbote. No steel is produced in Peru now. Utah Construction formed the Argonaut Mining Co. last year, and was shipping iron ore from British Columbia to Japan at a rate of more than 50,000 tons a month, before winter weather decreased operations.

Jan 1, 1952

By G. F. Bolling

HE high mobility of grain boundaries in zone-refined metals has been particularly demonstrated for lead above 150°C in grain growth studies1 and in the extensive work by Aust and Rutter.1 In these investigations, no elaborate precautions were taken to eliminate oxygen from the zone-refined lead; however the alteration of creep characteristics by oxygen concentrations of less than 5 x 10 -5 wt pet

Jan 1, 1962