Search Documents

By G. R. Countryman, G. H. Thomas, I. Fatt

Miscible displacement in both thewetting and non-wetting phase has been studied in two-phase systems. Experimental data show that dispersion is a function of saturation and cannot be predicted from dispersion theory developed for single-phase miscible displacement. Some of the effect of saturation on dispersion is a result of the development of dead-end pores or a dendritic pore structure in multiphase systems. The presence of dead-end pores or dendritic structure is confirmed by pressure transient studies. INTRODUCTION Displacement by flooding with a miscible liquid is a possible means for recovering the estimated two-thirds of the oil that remains behind after primary production. The immense economic importance of a process that can recover such large quantities of oil has led to extensive laboratory studies of miscible displacement. As usual in production research, most laboratory studies of miscible displacement have not attemped to reproduce all of the conditions existing in a petroleum reservoir. In the early stages of investigation the need has been for information on the broad, basic principles of the phenomena involved in miscible displacement. The effects of overburden pressure, reservoir temperature, and wettability have been considered of secondary importance. However, one property of a petroleum reservoir which is expected to be of major importance and yet has been omitted from many laboratory studies is the presence of interstitial water. Two possible effects of interstitial water on the displacement mechanism in the hydrocarbon phase immediately come to mind. First, from the general1y accepted theory that capillarity governs the distribution of oil and water in porous rock one would expect that for water-wet rock the water will be in the small pores and oil in the large pores. A miscible displacement of oil carried out in the presence of water is operating in a pore size distribution shown in Fig. lb, whereas if the same test had been performed with only one phase present the pore size distribution is as shown in Fig. la. Although there is not yet a theory of miscible displacement which explains in detail the effect of pore size distribution, one would expect the differences between Figs. la and lb to influence the displacement efficiency. A second factor which may make a multiphase system different from a single-phase system is the presence in the multiphase system of dead-end pores or dendritic structure. Experiments of various kinds on reservoir rock have led to the belief that all pores in the network structure of a porous rock take part in conducting fluid during single phase fluid flow.1,2 There are then no dead-end pores and no fingers or dendritic structures containing stagnant fluid. In a multiphase system, however, the second phase may

By Robert L. Marovelli

A recent reorganization placed the health and safety research activities of the Bureau of Mines under a director, Division of Minerals Health and Safety Technology. The new health and safety research organization and its position in the Bureau hierarchy is shown in Table 1.

Jan 11, 1979

By A. Manganwidjoyo, W. A. Wiebenga

The aim of this paper is to disclose some of the correlations between rock parameters, hidden in Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks," 1956. The empirical relations concern dry rocks of varying porosity. Curves and equations interrelating the specific gravity, compressive strength, bar velocity, and Poisson's ratio are presented. In 1956 Wuerker published his "Annotated Tables of Strength and Elastic Properties of Rock", in which various physical properties of rocks determined by different authorities, are tabulated systematically. The tables are primarily intended for use by mining-, quarrying- and ore-dressing engineers. Since the list of measured parameters for each type of rock includes properties such as — grain size, specific gravity, porosity, compressive strength, static elastic cons:ants (moduli of elasticity, rigidity, specific damping capacity and longitudinal bar velocity) the tables are also of considerable interest to the practical geophysicist. Correlations between rock parameters may enable geophysicists, geologists and civil engineers to transiate measurements from one parameter to another. Even if these translations are of limited accuracy, or valid only within certain specified ranges, they often serve a useful parpose. The aim of this paper is to disclose some of the correlations between rock parameters concealed in wuerker's Tables. Throughout this paper the following symbols and units are used unless otherwise stated: Sg is Specific gravity, the ratio of the density of a specimen to the density of water at 4°C. P is Porosity, in %, the ratio of the volume of voids in a specimen to its total volume. CS is Compressive strength in 1000 p.s.i., the stress under which a specimen will fracture when undergoing a standard compression test. V is Bar Velocity in kilo-feet/sec, the velocity of longitudinal seismic waves measured in a slender bar type specimen. Vc is Bulk or Constraint Velocity in kilo-feet/ sec, the velocity of longitudinal seismic waves measured in a very large specimen.+is Reciprocai bar velocity in millisecs/ft (1 millisec = 10-3 sec). cis Poisson's ratio, the ratio of the lateral to longitudinal strain of a body under longitudinal stress. CORRELATIONS Specific Gravity (Sg) vs. Porosity (P) Figure 1 is a diagram illustrating the relatiooship between specific gravity and porosity for approuirr~ately 70 samples of dry rocks. A curve fitted by estimation to this data yields the empirical formula: Sg =-0.0268P + 2.67 * 0.2 (1) Considering unit volume of a porogs specimen then

Jan 1, 1961

By Goldye Leeds, Marian Balicki

A SURVEY of literature reveals the scarcity of experimental evidence relating to work hardening and reannealing of silver.'-'" With the exception of the well-known X-ray investigation of silver and other metals by W. A. Wood? the effect of progressive cold working has not been studied. The determination of thermal stability of silver in the work-hardened state by means of isochronal or isothermal annealing has been confined apparently to very high reductions only. In the survey made, no study was encountered which endeavored to produce a complete picture of the changes in various properties due to cold working and subsequent reannealing. To fill these gaps and to assemble data that could be used for the determination of activation energies and of frequency coefficients of primary recrystallization, a systematic experimental approach, which was developed by one of the authors, has been applied to pure silver. Material and Processing The silver used was Handy and Harman fine silver, with a spectroscopic analysis at the testing stage of Cu, 0.0001 to 0.001 pct; Te, 0.0001; Pb, Si, Ca, Mg, and Mn, traces. The material was supplied in the form of a rod 0.406 in. diam and was converted into test samples according to the procedure condensed in Table I. It should be mentioned that air annealing was adopted to simulate industrial practice, though it was realized that annealing in a neutral gas or in a vacuum would be preferred. The usual precautions have been taken to eliminate any structural changes and property changes resulting from the storage of the samples prior to annealing or testing. Thus the wires were kept at the fully annealed stage, and the final wire drawing, which produced the desired degree of work hardening, was done just prior to the final annealing or testing. During the short waiting period, the samples were kept in a thermosflask filled with ice. Even with these precautions some strain-age-hardening or self-annealing could occur. To test such a possibility, wires of different reductions were prepared in the manner adopted and portions of them were immediately tested. The remaining portions were similiarly tested after different periods of storage, both at room and melting-ice temperature. Within experimental error, all samples obtained from a wire of a given percentage of reduction yielded identical values. This result qualified the material for further tests and interpretations, because it showed that either strain-age-hardening and self-annealing were absent, or that these effects fully balanced each other. The final annealing was carried out in an electric resistance furnace automatically controlled to within a 10°F. It was realized that the temperature fluctuations were greater than desired for this type of work. TO diminish the errors due to fluctuations of temperature, the hot junction of the thermocouple was placed as close to the samples as possible; the time of soaking was reduced to 15 min; and the number of samples annealed at different temperatures was increased. It will be seen from Table I that some tests were performed on the same material at rising temperature. These will be discussed elsewhere. Room temperature testing was limited to the determination of some of the mechanical properties that are known to be additive in a degree sufficient to be used for indirect study of the kinetics of the reannealing process, Tensile tests, carried out on a manually operated J. Camillon machine, accurate to within permitted the determination of the ultimate stress (U.S.1 and of the 2 in. elongation, (A,). The proof stress (d,e) has been determined from a series of bend tests carried out on a Tinius Olsen Stiffness Tester by using the offset method. This involved accurate determination for each sample of load-angular deflection curves, finding a

Jan 1, 1952

By P. G. Winchell, R. J. Russell

The distribution of displacements of originally plane surfaces by an invariant-plane strain has been analyzed statistically. The displacement ratio (the magnitude of the displacement of a point originally a unit distance from the invariant plane) can be determined from an analysis either of tilts of random surfaces or of displacements of random scratches scribed on a randowz surface. In either case the mean of the tangent of the observed displacement angle is related to the displacement ratio, and the number of observations used in determining the mean is related to the confidence limits placed on the estimate of the displacement ratio. In estimating the effect of applied stress on a phase transformation whose displacement effects can be approximated as an invariant-plane strain,* the dis- placement ratio of the invariant-plane strain is of primary importance. Two procedures for determining such displacement ratios are considered here. In the tilt method the measured quantity is taken to be the angle through which a random polish plane is rotated by the invariant-plane strain. In the scratch method the measured quantity is taken to be the angle between the original direction of a random scratch in a random polish plane and the projection of its final direction in the polish plane. In order to obtain precise results from either of the methods, it is necessary to measure the relative volume change associated with the strain in a separate experiment. TILT METHOD A locally homogeneous invariant-plane strain, P, with displacement ratio, S, may be written&apos; where ; and < are unit vectors indicating the displacement direction and invariant-plane normal, respectively, as pictured in Fig. 1. Eq. [I] describes a uniaxial strain if the direction of displacement is parallel to the invariant-plane normal and a pure shear strain if the displacement direction is perpendicular to the invariant-plane normal. The original orientation of the random polish plane relative to the invariant plane and to the displacement direction is shown in Fig. 2. The angle 03 between < and u is related to the relative volume change, ?V/V, and to the displacement ratio by As a result of the invariant-plane strain, the polish plane is rotated about its intersection with the invariant plane by the angle y, which is always taken to be positive. The tangent of this angle in terms of the above parameters is

Jan 1, 1967

By Douglas Bunting

The first presentation of this paper was before the Pennsylvania Anthracite Section of the Institute in May, 1914, after which a committee was selected to verify and add to the data contained in the original paper. The author is indebted to G. W. Engel, H. W. Montz, R. V. Norris, and H. H. Otto, of this committee, for additional information. I also wish to acknowledge the courtesies extended me by a number of the mining companies for information relative to accidents, systems of proving, and mining practice. The paper should bring forth additional criticism and recommendations, which will be of value in establishing future practice relative to this subject. Throughout the northern anthracite field of Pennsylvania glacial and alluvial deposits of sand, gravel, and clay exist in varying quantities. The extent and character of these deposits are described by N. H. Darton in Bulletin 45 of the U. S. Bureau of Mines, entitled, Sand Available for Filling Mine Workings in the Northern Anthracite Basin. It is estimated that the northern field contains 10,000,000,000 tons of these deposits, or a sufficient quantity to cover the 176 square miles of coal area to a depth of about 25 ft. These deposits of sand, etc., overlying the coal measures attain a maximum depth of more than 300 ft., and are usually saturated to such an extent as to render them semi-fluid. It is this condition of fluidity that limits the mining of coal seams cropping in or in close proximity to these deposits, and it is in the interest of safer and more efficient mining methods under these conditions that the study of this subject is here presented. The dangers incident to mining under deep deposits of sand have long been realized by operators in the northern anthracite field, and much has been done to prove the contour of the rock and vein croppings underlying these water-bearing deposits of sand and gravel. Although, as far as we know, the accidents of the past have not resulted in the loss of life, except in two instances, yet nearly all were attended with more or less miraculous escapes of men working in the vicinity of the breaks, so that the probable existence of pot holes, etc.,

Jan 1, 1915

By W. F. Mattes

The manufacture of steel rails in the United States upon a large scale may be roughly dated from the years 1875-76, and the same years witnessed an active movement among the railroads toward the adoption of heavier and improved patterns. In this movement each road was a law unto itself, and the "personal equations " of some scores of engineers were so freely injected into the calculations that patterns were multiplied in the most absurd and mischievous manner, until at length the burden upon the mills became wellnigh unendurable, and called forth a vigorous protest in Mr. Holley&apos;s paper,* read before the Institute in February, 1881. There were then regularly manufactured in the various mills of the United States, no less than 119 different patterns of steel rails, subject to current order, of which 64 per cent. were embraced under five weights per yard. Commenting upon these and other figures there given, Mr. Holley stated as the primary object of his paper, " to show that,, while this multiplication of rail-patterns is an annoyance and an expense to rail-makers, it is a source of immense loss to railway companies." Since 1876 the increase in gross annual tonnage upon our leading lines has been very great, and has been accompanied by an increase of wheel-loads and running-speeds. As the average weight of the rails of 1876 was by no means excessive, the growing deman Is of traffic have slowly driven the roads toward stiffer sections, inaugurating a movement that now promises to become epidemic. In 1876 a 67-pound rail was a first-class equipment; to-day everything under 75 pounds is light, and many 80&apos;s are coming into use. European practice has long been heavier than ours; in part because the higher cost of sleepers has led to an average of 3-feet spacing, instead of two-feet as with us. The old 84-pound double-header, and Sandberg&apos;s 80- and 89-pound rails, respectively 51/4 inches and 591/2 inches high, are reported common on English roads; and he is strongly advocating the general adoption of the 100-pounder shown in Fig. 7, with what success I have not learned, except that the Belgian government has ordered a lot. Mr. Sandberg points out the undesirability of frequent changes of pattern, and the recent rapid growth in traffic-requirements; prognosticates a continuance of this

Jan 1, 1887

By R. A. Esmonde

This paper describes the building and testing of a prototype welded aluminum truck body to a new design concept. The results of these tests are given along with an outline of further developments in the design and field application of aluminum bodies. The results of field service history are recorded with special reference to types of mining operations, service performance, wear, maintenance and economics of operation. Mention is made of current U.S. usage and predictions given as to future development of aluminum bodies in the mining industry. The use of aluminum for off-highway truck bodies in hauling rock for the mining and construction industries is by no means the novelty that it may seem. In 1932 an aluminum unit proved very satisfactory in service on the Hoover Dam project but at that time the only high strength aluminum alloys available were not weldable and with the high cost of construction, a sound economic case for an aluminum body could not be made. After World War I1 great advances in aluminum welding techniques, using the inert gas shield, combined with the development of high strength alloys with good welded properties and welding characteristics changed the whole picture. Welded aluminum bodies were rapidly developed and by 1958 attention was again focused on the use of aluminum for off-highway truck bodies. EARLY DEVELOPMENT WORK In 1959 Alcan, the Aluminum Co. of Canada, embarked on an extensive development program to prove the durability and economics of aluminum truck bodies for the mining and construction industries. The first step was to design a prototype aluminum body which took particular advantage of the fact that the modulus of aluminum is only one third that of steel. This means that within the elastic range, aluminum moves three times as much as steel which makes it more flexible and capable of absorbing much greater impact shocks. A body was built and mounted on a 22-ton truck and taken to the Jeffery Mine of Canadian Johns Manville Company at Asbestos, P.Q., Canada. Very little information was available as to the order of stresses that were set up in off-highway truck bodies and so it was therefore decided to carry out a test program to find out this information.

Jan 1, 1969

THE Boston meeting, August 29-31, was in many ways one of the pleasantest the Institute has enjoyed in years. Much hard work had been done by the committee, and with excellent results. The program had been purposely restricted with the idea that a smaller, more homogeneous audience formed the best basis for a regional meeting, and the event fully justified the plan. The one hundred and sixty-three members and guests attending were dominantly interested in geophysical methods or their application, and, despite the highly technical character of the papers and the unusual heat, attendance and interest in the technical sessions were well sustained. The exhibition of geophysical instruments and aerial maps added greatly to the meeting.

Jan 1, 1928

By J. B. Newkirk, W. G. Martin

Oxidized cobalt powder is known to have a magnetic hysteresis loop which is asymmetric with respect to the magnetization axis. The experiment described herein shows that the orientation relationship between the basal plane of hexagonal cobalt and the oxide which forms upon it at 400°C is {111}ux//{100.1 }co <110>ux//<11.O> This orientation relationship allows a magnetic interaction between the antiferromagnetic oxide and the ferromagnetic substrate which could account for the offset hysteresis loop. Oxidized nickel powder has a symmetrical hysteresis loop and so is apparently not influenced by any magnetic interaction between metal and oxide. The orientation of the oxide (cubic) was found to be identical with that of the nickel substrate when the oxide forms on a polished surface parallel with {111} Ni. IN 1956 W. H. Meiklejohn and C. P. Bean discovered that fine particles of cobalt which had been prepared in a certain way have a magnetic hysteresis loop which in a strong field is asymmetric relative to the magnetization axis.&apos; The cobalt powder exhibited this unusual magnetic property only after it had been oxidized in air or oxygen; it lost the shifted hysteresis loop when the oxide was reduced in hydrogen. X-ray and neutron diffraction&apos; experiments showed the presence of cobaltous oxide (COO) and hexagonal cobalt in samples exhibiting the biased hysteresis loop and specifically showed no indication of any other compound with the exception of mercuric oxide.* The magnetic hysteresis loop becomes symmetrical above the Nee1 temperature (paramagnetic state) of COO. Therefore, it was concluded that the anomalous magnetic behavior is associated with the influence of cobaltous oxide upon the metallic cobalt. It has been proposed that crystallographic coherency may exist between the cobalt and a plane of some antiferromagnetic material which has unbalanced spin distribution and sufficient magnetic anisotropy to hold its spin in the direction which existed when the specimen was cooled. COO has these properties. Therefore, Roth&apos; has suggested that cobaltous oxide may form with a {111} plane parallel and coherent with the basal plane of the hexagonal cobalt metal and proposed that, as consequence of the antiferromagnetic interaction between COO and the underlying cobalt, the magnetization direction in oxidized fine Co particles may be ro-lated from the easy c-direction.2 Such a relationship, he proposed, would explain the observed magnetic effect in oxidized cobalt powder. The main purpose of this study was to determine the orientation relationship, if any, between the basal plane of cobalt and the oxide which forms upon it. Attempts to produce a film of COO which was strong enough to be handled were not successful. However we did succeed in making a film of CoCo2O, which was strong enough to be removed from the cobalt substrate and mounted on an electron-microscope grid. Because of the close structural similarity of COO and CoCo2O, we believe the orientation relation found for CoCo2O, on cobalt probably also holds for COO on cobalt. The epitaxial relationship of NiO and Ni also was investigated. To date no shifted hysteresis loop has been observed with nickel powder. However, the similarity of atomic array in cobalt and nickel leads to the prediction that a {111} of NiO may be parallel with a (111} of nickel. Experimental Method Cobalt-Cobalt Oxide—A coarse-grained specimen of a (hexagonal) cobalt was prepared by allowing a large crystal of fee cobalt to transform slowly at 400°C. The crystal was then cut to expose a surface parallel with the basal plane. A back reflection Laue X-ray photograph showed that the 00.1 plane was within 2" of the cut surface. The surface was mechanically polished and then electro polished in 85 pet orthophosphoric acid after which the crystal was held for 30 min at 400°C in air. During this heat-treatment the surface darkened slightly due to the oxide film which formed. The film was not thick enough to give an X-ray diffraction pattern, even by a glancing-angle technique. Glancing-angle electron diffraction was not possible either, owing to the interference of the electron beam with the high magnetic fields which exist at the 00.1 surface of the cobalt. However, it was possible to make an electron-diffraction photograph of the oxide film by stripping it from the cobalt substrate using the method described later. By maintaining reference marks carefully, it was possible to preserve the orientation relationship between the stripped film and the substrate on which it was formed. The oxidized surface of the crystal was first covered with a 1 pet solution of collodion (cellulose nitrate) in amyl acetate. When the film was dry, small rectangles were scored on the surface with a needle point. The specimen was then repolished

Jan 1, 1959

An appropriate change in Art. I, Sec. 9, of the bylaws was voted by the Board on April 16 whereby, in the case of Student Associates applying for change of status to Junior Member, only two endorsers are needed instead of three, provided one of them is the same member who endorsed his original application for Student Associateship.

Jan 1, 1952

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 12, 1979

By S. Zelouf, G. Simkovich

THE role that impurities play as dopants in the movement of species in ionic and semiconductor crystals was first conclusively demonstrated by Koch and Wagner.&apos; At a later date Wagner demonstrated the effect of small amounts of alloying additions upon oxidation rates of pure metals, i.e., the effect of impurities as dopants in the scale being formed.&apos;

Jan 1, 1970

By Hugh Douglas

ANTIMONY Antimony (Sb) has been used since the early Egyptian dynasties. Prior to World War I, total demand amounted to only 6000 to 7000 tons per year (tpy). Wartime uses and rapid rise of industrialization in the Northern Hemisphere nations have pushed world antimony use to the 78,000-tpy level. An overwhelming supply of low-cost antimonial resources in the Sino-Russian bloc countries has and will continue to have a major impact on availability and price to users outside the bloc. Table 14.4.1 shows trends in world production, United States production and consumption, and prices. Demand Antimony is used principally as an alloy in lead-based metals and other alloys. Pure metallic antimony usage is small and is confined to such areas as laboratory and electronic applications. Lead-antimony alloys are used in automobile storage batteries, chemical pumps, and pipes, tank linings, roofing material, and cable sheaths. The metal increases the hardness of lead, and, for such uses as foundry printing type, reduces shrinkage for casting and lowers the melting point. Antimonial oxides are used for ceramic purposes, white paint pigments, glass forming, textile finishing, fire retardants in military clothing, matches, and solder. Wartime applications include use as hardener for bullets, an element for tracer bullets, and ingredient for producing dense white smoke for visual markers. A small but rapidly growing use for antimony is for metallic compounds in semiconductors and thermoelectric devices. In the United States demand for antimony is about evenly divided between metallic end-use markets and nonmetallic markets. In metallic end uses, antimonial lead accounts for 27% of total metallic and nonmetallic use; in nonmetallic areas major uses are flame retardants (15%) which is the fastest growing market, plastics (13 % ), and ceramics and glass (11%). While antimony has advantages in most of its applications, there are uses in which other materials can be substituted, including: mercury, titanium, lead, zinc, chromium, tin, and zirconium in paints and pigments; tin in sheathings; calcium in battery plates; and bismuth in type metal. Supply Antimony is produced from both antimony ores and as a byproduct of smelting other ores. The principal ore mineral is stibnite (Sb2S3), along with its oxidized antimonial minerals and derivatives which occur in small discontinuous replacement veins or fissure vein implacements. Stibnite occurs in quartz-gold veins and copper-lead-zinc

Jan 1, 1976

MANY kinds of marcasite* are found since every metallic mineral, and perhaps some of the semiminerals, produces its own. I believe that [28v] rnarcasites are nothing other than the secondary materials and the menses of the conception of metals which, through insufficient time, have yet to arrive at their perfect age; and thus, because of

Jan 1, 1942

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250&apos; to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,&apos; and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By Carl R. Christiansen

Since the first pay hole in Missouri&apos;s "New Lead Belt" was drilled in 1955, this district has become one of the world&apos;s leading sources of lead. The belt extends from north of Viburnum in a southerly direction to near Eminence, a distance of about 35 miles. The St. Joseph Lead Company was the discoverer and first to develop new mines in the Viburnum area. Since the discovery of the New Lead Belt, many companies have engaged in exploration programs and several major companies have become active in development of new mines. These include Cominco American, Inc., which operates a joint venture with Dresser Industries; Ozark Lead Company, a subsidiary of Kennecott Copper Company; and Missouri Lead Operating Company, a joint venture of Arnax and Homestake. St. Joseph Lead Company, with over 100 years of experience in the Old Lead Belt, has served as a leader in development of equipment and mining techniques, making its properties some of the most efficient mining operations in the world. The new producers give the district the benefit of fresh viewpoints, as their engineers are mostly from outside of Missouri and their previous experience has been considerably different from conventional lead belt practices. While all operations are similar in that they are room-and-pillar, the diverse experience of the operators has produced a group of mines that employ a variety of equipment and mining techniques to give increased efficiency

Jan 1, 1970

I HAVE striven to demonstrate to you as well as possible the method of bringing the metals of your ores to their ultimate perfection. But one cannot always do with gold that is found in the ores what is done with the other metals, for gold is not always accompanied by fine silver nor is it

Jan 1, 1942

By F. F. Claussen

The method of making silver ingots in use at this Mint being radically different from that employed at any other Mint of the United States or, so far as known to me, any Mint in the world, there may be some interest in a description of the apparatus used and a brief history of its distinguishing feature, viz., the rotary ingotmould, which, though not a recent improvement, is comparatively unknown. The furnaces used for silver-ingot-melting are four in number and have a capacity of some seventy thousand standard ounces of silver per day of eight hours. This output is increased, when the exigencies of the service demand it, to one hundred thousand ounces. They are built of fire-brick and elevated 21/2 feet from the floor of the melting-room, in order to have space to place iron boxes and to work, in case a crucible breaks in the furnace and its contents run into the ash-pit. The furnaces are circular in horizontal section, 2 $ feet in diameter and 29 feet high inside in the clear, and rest on castiron plates, with top-plates of the same, and sides encased in boileriron. The furnace-covers are also of cast-iron, dome-shaped, and are handled by means of a small crane and lever. The furnaces stand in sets of two, and one crane and one ingot-machine serves two furnaces. The crucibles used are made specially for this purpose of a mixture of black-lead and fire-clay; the size known as No. 200 will contain and safely melt, without danger of slopping over, from 8600 to nearly 10,000 ounces of standard silver; and this is the usual weight of the ingot-melt at this Mint, as against 1800 ounces at the Carson City mint and 2600 to 3000 ounces at Philadelphia and San Francisco. Each crucible will endure, on the average, ten melts. The crucible stands in the center of the furnace, on the bottom of an old one, cut down to a height of about three inches. The fuel used is coke. Experience has shown that, notwithstanding the higher first cost, Connellsville coke is cheaper than Alabama coke and much more suitable to the work. A small triangular black-

Jan 1, 1888